Alamo 02986941P User Manual

Boom Arm Mower

Rev 02-12 Part No. 02986941P

PART'S MANUAL

An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy before operating the equipment.

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 210-372-3551

TO THE OWNER/OPERATOR/DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that

you retain. The use of "will-t" parts will void your warranty and can cause catastrophic failure with possible injury or death.

BOLT TORQUE

Mounting procedures for mowers will require a signicant amount of bolt nut and washer installation.

Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness.

Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart.

Bolt tightness should be completed with and checked with a suitable torque wrench.

Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual.

Loose bolts on a frame or in a casting may be a result of:

● Vibration from the mower due to imbalance of the mower blades

● Pulled threads due to over tightening

● Distortion of the hole due to under tightening during installation

Bolts broken or sheared in the mounting structure or tractor may be the result of:

● Improper alignment of the Mounting Plate or Structure such that it is not sitting at on the mating surface

● Distortion of the bolt due to over-tightening

● Under tightening of the bolts

Check the bolt torque during installation and prior to delivery with a suitable torque wrench.

PARTS

SECTION

Parts Section – 1

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and

are subject to special handling. Request a quotation for such parts before sending a Purchase

Order.

6. The Manufacturer reserves the right to change prices without prior notice.

For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Parts Section – 2

PART NAME INDEX

48 IN FLAIL AXE - HEAD ASY (PART 1)................................................................................................................................................. 5

48 IN FLAIL AXE - HEAD ASY (PART 2)................................................................................................................................................. 7

48 IN FLAIL AXE - HEAD ASY (PART 3)................................................................................................................................................. 9

50 IN ROTARY - BLADE BAR - HEAD ASY (SOLID MNT)................................................................................................................. 11

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SOLID MNT)........................................................................................................ 13

50 IN ROTARY - BLADE BAR - HEAD ASY (SWIVEL MNT)............................................................................................................. 15

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SWIVEL MNT).................................................................................................... 17

50 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 19

50 IN ROTARY - BLADE PAN - HEAD ASY (SOLID MNT)................................................................................................................. 21

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SOLID MNT)........................................................................................................ 23

50 IN ROTARY - BLADE PAN - HEAD ASY (SWIVEL MNT).............................................................................................................. 25

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SWIVEL MNT)..................................................................................................... 27

50 IN ROTARY - BLADE PAN ASY......................................................................................................................................................... 29

60 IN GRASS FLAIL - HEAD ASY (SOLID MNT).................................................................................................................................. 31

60 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 33

60 IN ROTARY - HEAD ASY (SOLID MNT)........................................................................................................................................... 35

60 IN ROTARY - HEAD SUB-ASY (SOLID MNT).................................................................................................................................. 37

60 IN ROTARY - HEAD ASY (SWIVEL MNT)....................................................................................................................................... 39

60 IN ROTARY - HEAD SUB-ASY (SWIVEL MNT).............................................................................................................................. 41

ROTARY - MOTOR AND SPINDLE ASY................................................................................................................................................ 43

ROTARY - MOTOR ASY (PART 1).......................................................................................................................................................... 45

ROTARY - MOTOR ASY (PART 2).......................................................................................................................................................... 47

ROTARY - SPINDLE ASY......................................................................................................................................................................... 49

BOOM ASY - 18 FT BOOM (PAGE 1)...................................................................................................................................................... 51

BOOM ASY - 18 FT BOOM (PAGE 2)...................................................................................................................................................... 53

BOOM ASY - 22 FT BOOM (PART 1)...................................................................................................................................................... 55

BOOM ASY - 22 FT BOOM (PART 2)...................................................................................................................................................... 57

BOOM ASY - 25 FT BOOM (PART 1)...................................................................................................................................................... 59

BOOM ASY - 25 FT BOOM (PART 2)...................................................................................................................................................... 61

BUZZ BAR ASY - 48 IN (PART 1)............................................................................................................................................................ 63

BUZZ BAR ASY - 48 IN (PART 2)............................................................................................................................................................ 65

BUZZ BAR ASY - 69 IN (PART 1)............................................................................................................................................................ 67

BUZZ BAR ASY - 69 IN (PART 2)............................................................................................................................................................ 69

BUZZ BAR ASY - 90 IN (PART 1)............................................................................................................................................................ 71

BUZZ BAR ASY - 90 IN (PART 2)............................................................................................................................................................ 73

BUZZBAR AND GRASS FLAIL MOTOR ASSEMBLY.......................................................................................................................... 75

BUZZ BAR SPINDLE ASSEMBLY........................................................................................................................................................... 77

COMMON CRATE COMPONENTS......................................................................................................................................................... 79

DECALS - 18-22-25 FT BOOM.................................................................................................................................................................. 81

DECALS - HYD TANK AND PUMP......................................................................................................................................................... 83

PART NAME INDEX

FILTER ASY................................................................................................................................................................................................ 84

HIGH FRAME MOUNT ASY - 2WD......................................................................................................................................................... 85

HIGH FRAME MOUNT ASY - 4WD......................................................................................................................................................... 87

HIGH FRAME MOUNT SUB-ASY............................................................................................................................................................ 89

HOSE ROUTING - 18 FT BOOM............................................................................................................................................................... 91

HOSE ROUTING - 18 FT BOOM NOTES................................................................................................................................................. 92

HOSE ROUTING - 22 FT BOOM............................................................................................................................................................... 93

HOSE ROUTING - 22 FT BOOM NOTES................................................................................................................................................. 94

HOSE ROUTING - 25 FT BOOM............................................................................................................................................................... 95

HOSE ROUTING - 25 FT BOOM NOTES................................................................................................................................................. 96

HOSE ROUTING - HYDRAULIC KIT...................................................................................................................................................... 97

HYDARULIC CYLINDER ASY - DIPPER 22-25 FT BOOM.................................................................................................................. 99

HYDARULIC CYLINDER ASY - LIFT BOOM...................................................................................................................................... 100

HYDRAULIC CYLINDER ASY - HEAD SWIVEL (OPTIONAL)........................................................................................................ 101

HYDRAULIC CYLINDER ASY - SWING.............................................................................................................................................. 102

HYDRAULIC CYLINDER ASY - TILT.................................................................................................................................................. 103

HYDRAULIC TANK SUB-ASY.............................................................................................................................................................. 105

HYDRAULIC TANK W/PUMP AND ELECT VALVE ASY................................................................................................................. 107

JOYSTICK CONSOLE ASY..................................................................................................................................................................... 109

PUMP ASY - SERVO CONTROLLED (PART 1)................................................................................................................................... 111

PUMP ASY - SERVO CONTROLLED (PART 2)................................................................................................................................... 113

PUMP ASY - VARIABLE DISPLACEMENT......................................................................................................................................... 115

PUMP-TANK-VALVE COVER............................................................................................................................................................... 117

VALVE - PARTS - OPEN & CLOSED CENTER.................................................................................................................................... 119

VALVE ASSEMBLY - ELECTRO-HYDRAULIC VALVE................................................................................................................... 121

WIRE HARNESS ELECT-HYD VALVE................................................................................................................................................. 123

48 IN FLAIL AXE - HEAD ASY (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 02970301 1 WLDMT, FLAIL AXE HEAD 2 02957655M 1 ASY, CUTTERSHAFT, 48" F/A

02989696 1 ASY, CTRSHFT, SHD, EXT SERV. KNIVES 3 02970465 1 WLDMT DOOR, 48" FLAIL AXE 4 02973256 1 WLDMT, MOTOR MOUNT 5 02970709 1 PLATE, COVER FLAIL AXE 6 10119000 2 HHCS 5/16 NC 1 PL5 7 00023500 6 FLATWASHER 5/16, TYPE AW, ZP 8 00750940 2 NUT, TOPLOCK 5/16 NC PL B 9 02958131A 2 FLANG BEARING ASY 10 02956714 1 CLAMP BAR 11 02956712 1 RUBBER FLAP 12 02970326 1 ROD-HINGE, F/A DOOR 13 02958198 1 1/2 X 1/2 X 1 7/8 LG 14 02970585 1 WLDM SKIDSHOE INSIDE FLAIL AXE 15 02956748 1 SKID SHOE WLDMT 16 02970540 1 WLDMT - REAR ROLLER 17 02967325 2 PULLEY, 3G5V - 8.50 DIA 18 02970325 1 PLATE-BELT & PULLEY COVER 19 02972442 1 FLAIL AXE BEARING GUARD 20 02970763 1 PISTON MOTOR 21 02675800 2 HHCS 5/8 X 1-1/2 PL GR5 22 00010300 2 HIGH ALLOY, L/W 5/8 YZ KG 23 00001400 4 FLATWASHER 5/8 PL STD 24 02892000 8 HHCS 1/2NC 1-1/2 LG PL8 25 00001800 11 LOCKNUT TLM 1/2 NC PLB 26 00752670 1 GREASE FITTING 1/4-28 BOLT THD 27 00008300 6 BOLT, HHCS 5/8" NC X 1-3/4" PL5 28 00695100 5 LOCKNUT TOPLOCK 5/8NC PLB 29 02970710A 1 CYL, DOOR, 48" F/A 31 000941 1 GREASE ZERK 1/4-28 90 BOLT THD 32 02970583 4 SHCS 3/8 NF 1-1/2 PL GR5 33 23504500 8 JAMNUT 3/8 NF 34 03200925 1 CARR 5/8 NC X 3 PL GR5 35 02967328 1 BUSHIN, QD HUB SF 1-15/16 ID 36 02970725 1 BUSHIN, QD HUB SF 1-1/8 ID 37 00013500 3 NUT, 3/8 NC JAMNUT 38 02970539 3 V BELT 39 02956768 2 PIN, ROLL 5/32X1 40 00011700 4 HIGH ALLOY, L/W 5/16 YZ KG 41 00035900 4 HHCS 5/16 NC X 3/4 GR5

48 IN FLAIL AXE - HEAD ASY (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

42 000642 7 LOCKNUT TLM 1/2 NC PLB 43 00002700 7 FLATWASHER, 1/2 PL STD 44 00019300 7 HHCS 1/2 X 1-1/2 NF GR5 PL 45 02957041 2 ROLLER BEARING & FLANGE 46 00013300 2 BOLT, HHCS 1/2" NC X 2" PL5 47 02972949 2 BOLT, HHCS 3/8 NC 1-1/4 PL8 48 02970586 2 WASHER, 2 X 7/16 X 3/16 49 02977955 4 HHCS 3/8NC 1-1/2 PL GR8 50 00015800 4 LOCKNUT TLM 3/8 NC PLC 51 00003300 1 HHCS 3/4" X 4" LG 52 00037200 7 NUT 3/4 NC LOCKNUT 53 00605600 1 HHCS 1/2 X 3-1/4 NC PL 54 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 59 02043600 2 ADP, HYD ELBOW 16MB - 16MJ 45 60 00696800 1 ADP HYD STGHT 8MB-8MJ 61 02968896 1 PLASTIC TIE, ORANGE, 11LG 62 02968894 1 PLASTIC TIE, RED, 11LG 63 02968895 1 PLASTIC TIE, BLUE, 11LG 65 02968836 1 PLASTIC TIE, YELLOW 66 02968837 1 PLASTIC TIE, YELLOW & WHITE 67 002369 1 DECAL, DANGER, MULTI-HAZARD 68 02965141 1 DECAL, DANGER BOOM FLAILS 69 02967668 1 DECAL, THROWN OBJECTS 70 02967867 1 DECAL, DANGER SAFETY SHIELD 71 00725739 1 DECAL WARN. SHEILD&GUARDS 72 00758194 1 DECAL, WARNING, BELT SHIELD 73 02925100 1 DECAL, REPLACEMENT PARTS 74 000108 1 DECAL, INSTRUC, FLAIL OPER 75 000678 1 DECAL, GREASE FITTING INSIDE 76 00757139 1 DECAL, LOGO (ALAMO BY T.K.) 77 02970887 1 DECAL, LOGO, FLAIL AXE 48" 78 3710151 4 METAL TACK 79 02971501 1 PLATE, S/N FLAIL AXE 48" 81 02979551 1 DECAL, ALAMO INDUSTRIAL LOGO 82 03200521 1 KEY, STEP, 1/4X5/16X1 83 02970324 1 PLATE-CLAMP, HITCHPOST 84 02918600 6 HHCS 3/4 NC 2 PL8 85 02981757 2 WELDMENT, PIN, HITCH POST 86 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 87 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 88 02986218 1 WELDMENT, HITCHPOST

48 IN FLAIL AXE - HEAD ASY (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

88 02986218 1 WELDMENT, HITCHPOST 89 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 90 00011400 2 BOLT, HHCS 3/8 NC 1 PL5 91 02970301 1 WLDMT, FLAIL AXE HEAD 92 02892000 23 HHCS 1/2NC 1-1/2 LG PL8 93 00001800 11 LOCKNUT TLM 1/2 NC PLB 94 02970324 1 PLATE-CLAMP, HITCHPOST 95 00003300 1 HHCS 3/4" X 4" LG 96 00037200 13 NUT 3/4 NC LOCKNUT 97 00008200 1 BOLT, HHCS 1/2" NC X 3-3/4" PL5 98 02960018 4 ADP, HYD, ELBOW, 4MB-4MJ90 99 02918600 10 HHCS 3/4 NC 2 PL8 100 02981757 2 WELDMENT, PIN, HITCH POST 101 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 102 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 103 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 104 02984370 1 ADP, SWIVEL, FLAIL AXE 105 02981318 1 BEARING, 12OD X 5.8ID 106 02985319 1 WELDMENT, HITCH POST 107 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 108 02984374 1 WLDMNT, SWIVEL, CYL BRKT 109 02981820 12 SHCS 1/2 NC X 1 1/2" LG PL8 110 02963646 1 HHCS 3/4 NC 2-1/2 PL8 111 00754105 1 HHCS 3/4 NC 4 1/2 PL8 112 02984382 1 CLAMP, PLATE, SWIVEL 113 02984470 2 STOP, FLAIL AXE SWIVEL 114 00021400 2 BOLT, HHCS 1/4" NC X 3/4" PL 115 02959924 2 NUT, TOPLOCK 1/4 NC PLB 116 02968832 1 PLASTIC TIE, GREEN 117 02968833 1 PLASTIC TIE, GREEN & WHITE 118 00011400 2 BOLT, HHCS 3/8 NC 1 PL5

50 IN ROTARY - BLADE BAR - HEAD ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986704 1 ASY, 50" ROT, PISTON, BAR 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981757 2 WELDMENT, PIN, HITCH POST 14 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 15 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 16 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 17 651102 1 PIN-DRILLED 18 02976448 1 PIN - MACHINED HEAD 19 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 20 02968837 1 PLASTIC TIE, YELLOW & WHITE 21 02968836 1 PLASTIC TIE, YELLOW 22 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986704 1 ASY, 50" ROT, PISTON, BAR 1 00015800 18 LOCKNUT TLM 3/8 NC PLC 2 02891800 4 HHCS 1/2 NC 1-3/4 PL8 3 00019600 4 LOCKWASHER 1/2 HEAVY 4 02982907 2 SKID SHOE 5 02981411 1 WELDMENT, DECK 50" HEAD 6 02961038 1 GASKET 7 02982906 1 ASY, BLADE BAR W/BLADES 8 02964861 4 SHCS 3/4 NC 4" LG PL8 9 15B600 14 WASHER 3/8 SAE P 10 00003901 4 LOCKWASHER 3/4 HEAVY 11 00059700 14 FSCS 3/8 NC X 1-1/4 12 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 13 03200269 8 HHCS 3/4 NC 3 PL8 14 02963645 8 HHCS 3/4 NC 1-3/4 PL8 15 00037200 16 NUT 3/4 NC LOCKNUT 16 5312316 16 FLATWASHER 3/4 HARDENED 17 02986200 1 WELDMENT, HITCH POST 18 02979881 1 MOTOR PISTON 4.91 CID 19 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 20 02968894 1 PLASTIC TIE, RED, 11LG 21 02968896 1 PLASTIC TIE, ORANGE, 11LG 22 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 23 00022200 8 LOCKWASHER 7/16 PL 24 02968895 1 PLASTIC TIE, BLUE, 11LG 25 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG

50 IN ROTARY - BLADE BAR - HEAD ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986197 1 ASY, 50" ROT, PISTON, BAR, SW 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 20 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 14 02981757 2 WELDMENT, PIN, HITCH POST 15 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 16 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 17 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 18 651102 1 PIN-DRILLED 19 02976448 1 PIN - MACHINED HEAD 20 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 21 00754105 1 HHCS 3/4 NC 4-1/2 PL8 22 02963646 3 HHCS 3/4 NC 2-1/2 PL8 23 00037200 18 NUT 3/4 NC LOCKNUT 24 02968837 1 PLASTIC TIE, YELLOW & WHITE 25 02968836 1 PLASTIC TIE, YELLOW 26 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 27 02968832 1 PLASTIC TIE, GREEN 28 02968833 1 PLASTIC TIE, GREEN & WHITE 29 03200762 2 ADP, HYD 6MB-4MJ 90 30 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 31 02968894 1 PLASTIC TIE, RED, 11LG 32 02968895 1 PLASTIC TIE, BLUE, 11LG 33 02968896 1 PLASTIC TIE, ORANGE, 11LG

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986197 1 ASY, 50" ROT, PISTON, BAR, SW 1 00015800 20 LOCKNUT TLM 3/8 NC PLC 2 02963646 3 HHCS 3/4 NC 2-1/2 PL8 3 00037200 18 NUT 3/4 NC LOCKNUT 4 02968894 1 PLASTIC TIE, RED, 11LG 5 02968896 1 PLASTIC TIE, ORANGE, 11LG 6 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 7 02891800 4 HHCS 1/2 NC 1-3/4 PL8 8 02979881 1 MOTOR PISTON 4.91 CID 9 00022200 8 LOCKWASHER 7/16 PL 10 00019600 4 LOCKWASHER 1/2 HEAVY 11 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 12 02980237 2 O-RING .139 DIA X 1.296 INSIDE 13 02982907 2 SKID SHOE 14 02981820 28 SHCS 1/2 NC X 1 1/2" LG PL8 15 02981318 1 SLEWING BEARING, 12 OD X 5.8 ID 16 02985319 1 WELDMENT, HITCH POST 17 02981411 1 WELDMENT, DECK 50" HEAD 18 02961038 1 GASKET 19 02982906 1 ASY, BLADE BAR W/BLADES 20 02981752 1 PLATE, HITCH POST BOTTOM, MAVERICK 21 02964861 4 SHCS 3/4 NC 4" LG PL8 22 15B600 14 WASHER 3/8 SAE P 23 00003901 4 LOCKWASHER 3/4 HEAVY 24 00059700 14 FSCS 3/8 NC X 1-1/4 25 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 26 02963645 6 HHCS 3/4 NC 1-3/4 PL8 27 5312316 18 FLATWASHER 3/4 HARDENED 28 03200269 8 HHCS 3/4 NC 3 PL8 29 02984002 1 WLDMNT, STOP, SWIVEL

50 IN ROTARY - BLADE BAR ASY

ITEM PART NO. QTY. DESCRIPTION

02982906 1 ASY, BLADE BAR W/BLADES 1 02982912 1 LEAF, MIDDLE, BLADE BAR 2 02982913 1 LEAF, BOTTOM, BLADE BAR 3 02962634 1 BLADE-MATCHED SET-50B/A HD 4 02982934 1 WLDMT. TOP BLADE BAR 5 02782900 2 BOLT, BLADE 6 02957089 2 LOCKWASHER 1-1/8 PL STD 7 00020900 2 NUT, SLOTTED, HVY,1-1/8NF PL GR5 8 00023200 2 PIN, ROLL, 3/16X1-3/4 9 15C2000 4 WASHER, 1.375 X 2.50 X .165, HARDENED 10 02969235 2 HHCS, 1-1/4X3 PL GR8 11 02969236 2 HHCS, 1-1/4X2-1/4 PL GR8

THIS PAGE INTENTIONAL LEFT BLANK

50 IN ROTARY - BLADE PAN - HEAD ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986703 1 ASY, 50" ROT, PISTON, PAN 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981757 2 WELDMENT, PIN, HITCH POST 14 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 15 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 16 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 17 651102 1 PIN-DRILLED 18 02976448 1 PIN - MACHINED HEAD 19 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 20 02968837 1 PLASTIC TIE, YELLOW & WHITE 21 02968836 1 PLASTIC TIE, YELLOW 22 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986703 1 ASY, 50" ROT, PISTON, PAN 1 00015800 34 LOCKNUT TLM 3/8 NC PLC 2 02891800 4 HHCS 1/2 NC 1-3/4 PL8 3 00019600 4 LOCKWASHER 1/2 HEAVY 4 02982907 2 SKID SHOE 5 02981411 1 WELDMENT, DECK 50" HEAD 6 02961038 1 GASKET 7 02964804 1 PAN ASSY 50" HEAD 8 02964861 4 SHCS 3/4 NC 4" LG PL8 9 15B600 14 WASHER 3/8 SAE P 10 00003901 4 LOCKWASHER 3/4 HEAVY 11 00059700 14 FSCS 3/8 NC X 1-1/4 12 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 13 03200269 8 HHCS 3/4 NC 3 PL8 14 02963645 8 HHCS 3/4 NC 1-3/4 PL8 15 00037200 16 NUT 3/4 NC LOCKNUT 16 5312316 16 FLATWASHER 3/4 HARDENED 17 02986200 1 WELDMENT, HITCH POST 18 02979881 1 MOTOR PISTON 4.91 CID 19 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 20 02968894 1 PLASTIC TIE, RED, 11LG 21 02968896 1 PLASTIC TIE, ORANGE, 11LG 22 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 23 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 24 00022200 8 LOCKWASHER 7/16 PL 25 02968895 1 PLASTIC TIE, BLUE, 11LG

50 IN ROTARY - BLADE PAN - HEAD ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986198 1 ASY, 50" ROT, PISTON, PAN,SW 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 14 02981757 2 WELDMENT, PIN, HITCH POST 15 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 16 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 17 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 18 651102 1 PIN-DRILLED 19 02976448 1 PIN - MACHINED HEAD 20 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 21 00754105 1 HHCS 3/4 NC 4-1/2 PL8 22 02963646 3 HHCS 3/4 NC 2-1/2 PL8 23 00037200 18 NUT 3/4 NC LOCKNUT 24 02968837 1 PLASTIC TIE, YELLOW & WHITE 25 02968836 1 PLASTIC TIE, YELLOW 26 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 27 02968832 1 PLASTIC TIE, GREEN 28 02968833 1 PLASTIC TIE, GREEN & WHITE 29 03200762 2 ADP, HYD 6MB-4MJ 90 30 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 31 02968894 1 PLASTIC TIE, RED, 11LG 32 02968895 1 PLASTIC TIE, BLUE, 11LG 33 02968896 1 PLASTIC TIE, ORANGE, 11LG

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SWIVEL MNT)

+ 102 hidden pages