Aladdin Light Lift ALL300RM-CM-240V User Manual
ALL300RM-230V
INSTALLATION
INSTRUCTIONS
Aladdin Light Lift, Inc. (256) 429-9700
61 Shields Road (877) 287-4601
Huntsville, AL 35811 www.aladdinlightlift.com
Patent #5105349
WARNING: Disconnect power source before servicing to avoid electrical shock
CAUTION: To Reduce the Risk of Electric Shock or Injury, Use Indoors Only.
Light and motor circuits are rated at AC 230V
Pour usage seulement dans un endroit
Avec acces au dessus du plafonds
Model Number: ALL300RM (136.4) Kg rated working load, 1/8” steel galvanized lay cable,
1.5amp, 50/60Hz)
Light lift is equipped with a 65’ (19.8m) cable unless checked below:
______90’ (27.4m)
______120’ (36.6m)
Light lift is equipped with a 1,650 watt (15 amps)
lighting capacity unless checked below:
______2200 watts (20 amps)
________________________
Manufacture Date © 2012 All Rights Reser ved
Read the following guidelines prior to installing the ALL300RM:
I. e ALL300RM must be installed by a licensed, bonded, and insured electrician.
II. e ALL300RM must be installed in an accessible location.
III. oroughly read, understand, and follow each step and safety warning in the ALL300RM installation
instructions and orange safety precautions supplement.
IV. Motor pulley, directional pulley(s), and chandelier pulley must be installed on the same plane. Do not
install the ALL300RM with lateral cable direction changes.
V. During installation of the ALL300RM, take one step at a time and check o each step upon completion.
VI. Call Aladdin Light Lift (877) 287-4601 if assistance is needed for installation and/or operation of
the ALL300RM. Refer to the Keyswitch Controller Guide or SmartLift Controller Guide for operation
instructions.
VII. Ignoring any safety warnings and/or symbols not only voids the warranty, but may cause death, personal
injury, and/or property damage.
VIII. e wattage of the chandelier can not exceed the wattage capacity of the ALL300RM.
IX. Give all Aladdin paperwork to property owner and/or anyone that will be using the ALL300RM.
ALL300RM Parts Bag List
A. 5/16” x 2” Lag Bolts (QTY 4)
B. 5/16” x 1¼” Fender Washers (QTY 4)
C. Screw Collar Ring (QTY 1)
D. read Lock (QTY 1)
E. 3/32” Allen Wrench (QTY 1)
1/8 IPS(10mm) x 1/4 IPS(13mm) Fixture Coupler (QTY 1)
F. 1/4 IPS(13mm) x 3/8 IPS(16mm) Fixture Coupler (QTY 1)
1/4 IPS(13mm) x 1/2 IPS(22mm) Fixture Coupler (QTY 1)
ALL300 RM Hardware Box List
5/16” USS Flat Washers (QTY 4)
3/8” Nylon Lock Nuts (QTY 2)
3/8” x 1¼” Hex Tap Bolts (QTY 2)
7/16” x 4” Hex Tap Bolt (QTY 4)
3/8” USS Flat Washers (QTY 8)
7/16” Nylon Lock Nuts (QTY 4)
Side Brackets for Chandelier Pulley Bracket (QTY 2)
Flat Brackets (QTY 2)
per directional pulley (optional)
7/16” x 3¼” Hex Head (QTY 2)
per directional pulley (optional)
3/8” USS Flat Washers (QTY 4)
per directional pulley (optional)
7/16” Nylon Lock Nuts (QTY 2)
per directional pulley (optional)
STEP 1
Determine mounting location of ALL300RM motor assembly. e ALL300RM may be mounted on an
angle, vertically, horizontally or upside down, if secured properly. See Diagram A.
Never install the ALL300RM where the ceiling height and total cable run through the pulleys exceeds
1.5 meters less than the exact length of winch cable. For example, if the ALL300RM is equipped with a
65ft(19.8m) cable do not install the ALL300RM with a ceiling height and total cable run that is greater
than 60ft(18.3m). is could cause the cable to become reverse wrapped on the winch. An ALL300RM
installed with a reverse wrapped cable could cause the chandelier to fall, which could cause death,
personal injury, and/or property damage. Winch cable length can be found on the ALL300RM product
sticker, shipping box, and the front page of these installation instructions.
Diagram A
Upside Down
Level
Left Angle
Vertical
Right Angle
STEP 2
Determine mounting location of chandelier pulley assembly. Chandelier pulley assembly must be mounted
directly above where chandelier will hang. See Diagram B.
Never mount the chandelier pulley assembly o plane or unlevel in a remote installation. is could
cause the chandelier to fall, which could cause death, personal injury, and/or property damage. e
winch cable must hang plumb through the center of the top contact plate on the ceiling box.
Diagram B
Chandelier Pulley
Assembly Height is
Adjustable
From 29.2cm to 41.9cm
34.9cm Minimum
40.6cm Maximum
If Ordered With
Conduit Cut to
Minimum
Chandelier Pulley
Assembly Height
is Adjustable
From 19.7cm to
23.5cm
STEP 3
Determine mounting location of directional pulleys if they are to be installed with ALL300RM.
Directional pulleys can be used to change winch cable direction, up or down, between motor pulley and
chandelier pulley. See Diagram C.
Never mount directional pulleys o plane in a remote installation. is could cause the chandelier to
fall, which could cause death, personal injury, and/or property damage.
Diagram C
17.8
cm
Quick Link
10.2
cm
Flat Brackets
Suitable Structure
15.2
cm
Pulley
yes NO
STEP 4
Determine that cable position on motor pulley is correct for installation. ALL300RM is equipped with
cable running under motor pulley. See Diagram D.
Never position cable on motor pulley improperly. is could damage the cable which could cause the
chandelier to fall, which could cause death, personal injury, and/or property damage.
Diagram D
Under
STEP 5
If cable rubs on motor pulley housing or motor assembly plate, change cable conguration so that cable runs
over motor pulley. See Diagram E.
Never position cable on motor pulley improperly. is could damage the cable which could cause the
chandelier to fall, which could cause death, personal injury, and/or property damage.
Diagram E
Over
STEP 6
Position ALL300RM motor assembly where it will be mounted. Adjustments can be made loosening 3/8”
channel strut bolts that hold ALL300RM motor assembly to channel struts. Retighten channel strut bolts
after adjustments are made. Conrm strut nuts are seated properly. See Diagram F.
Never adjust the channel struts improperly. is could cause the chandelier to fall, which could cause
death, personal injury, and/or property damage.
STEP 7
Securely fasten ALL300RM motor assembly to a suitable structure using 5/16” lag bolts and 5/16” fender
washers included in parts bag. See Diagram F.
Never install the ALL300RM without properly fastening it to a suitable structure. is could interfere
with the safety and operation of the ALL300RM and could cause the chandelier to fall, which could
cause death, personal injury, and/or property damage.
5/16” Lag Bolts
5/16” FenderWashers
Diagram F
3/8” Channel Strut
Adjustment Bolts
3/8” Channel Strut
Adjustment Bolts
STEP 8
Turn o supply power before wiring ALL300RM motor switch. Turn o motor switch in square box. Wire
motor switch with 230V wiring. e 230V motor feed must be kept separate from 230V light switch leg.
Keep motor and light hots separate. One motor hot is black and 14 gauge. e other is white and 14 gauge.
Only wire motor switch at this time. See Diagram G.
Never wire the ALL300RM improperly. Make sure electricity is turned o when installing and/or
performing maintenance on the ALL300RM. Improper wiring and/or electricity could cause death,
personal injury, and/or property damage.
Aladdin 12 Gauge Light Hot
Diagram G
Aladdin 12 Gauge Light Hot
(White)
(Black)
Aladdin 14 Gauge Motor Hot
(White)
Aladdin 14 Gauge Motor Hot
(Black)
Do Not Wire Light
Switch At is Time
Light Motor
230V House Hot
For Motor
230V House Hot
For Motor
Loading...