Aladdin Light Lift ALL1000-CM-240V User Manual

ALL1000-230V

INSTALLATION

INSTRUCTIONS

Aladdin Light Lift, Inc. [phone]
61 Shields Road [phone]
Huntsville, AL 35811 www.aladdinlightlift.com

Patent #5105349

WARNING: Disconnect power source before servicing to avoid electrical shock

CAUTION: To Reduce the Risk of Electric Shock or Injury, Use Indoors Only.

Light and motor circuits are rated at AC 230V

Pour usage seulement dans un endroit

Avec acces au dessus du plafonds

Model Number: ALL1000(455Kg rated working load,7/32” steel galvanized lay cable,1.67amp,50/60Hz)
__ Greeneld _(if checked)

Light lift is equipped with a 35’(10.6m) cable unless checked below:
______65’(19.8m)
______90’(27.4m)
______120’(36.6m)

Light lift is equipped with a 2200 watt (20 amps)
lighting capacity

________________________
Manufacture Date © 2012 All Rights Reser ved

Read the following guidelines prior to installing the ALL1000:

I. e ALL1000 must be installed by a licensed, bonded and insured electrician.

II. e ALL1000 must be installed level, in an accessible location and directly above the chandelier.

III. oroughly read, understand and follow each step and safety warning in the ALL1000 installation
instructions and orange safety precautions supplement.

IV. During installation of the ALL1000, take one step at a time and check o each step upon completion.

V. e Troubleshooting Guide is located in the back of the Installation Instructions. Call Aladdin Light
Lift [phone] if assistance is needed for installation and/or operation of the ALL1000. Refer to the
Keyswitch Controller Guide or Smartlift Controller Guide for operation instructions.

VI. Ignoring any safety warnings and/or symbols not only voids the warranty, but may cause death, personal
injury and/or property damage.

VII. e wattage of the chandelier can not exceed the wattage capacity of the ALL1000.

VIII. e Warranty Agreement is located on the last page of Installation Instructions.

IX. Give all Aladdin paperwork to property owner and/or anyone that will be using ALL1000.

ALL1000 Parts Bag List

A. #10 x 1 ¼” Pan Phillips-Wood Screws (QTY 8)

B. 3/16” x 1” Fender Washers (QTY 8)

C. Screw Collar Ring (QTY 1)

D. read Lock (QTY 1)

E. 3/32” Allen Wrench (QTY 1)

F. 1/4 IPS(13mm) x 3/8 IPS(16mm) Fixture Coupler (QTY 1)
3/8 IPS(16mm) x 1/2 IPS(22mm) Fixture Coupler (QTY 1)

STEP 1

Determine where ALL1000 will mount on ceiling joists. ALL1000 must be installed level, in an accessible
location directly above chandelier.

Never mount the ALL1000 o plane or unlevel in a standard installation. is could cause the
chandelier to fall, which could cause death, personal injury, and/or property damage. e winch cable
must hang plumb through the center of the top contact plate on the ceiling box.

Never install the ALL1000 where the ceiling height exceeds 1.5m less than the exact length of winch
cable. For example, if the ALL1000 is equipped with a 35ft.(10.6m) cable, do not install the ALL1000
in a ceiling that is greater than 30ft(9.1m). is could cause the cable to become reverse wrapped on the
winch. An ALL1000 installed with a reverse wrapped cable could cause the chandelier to fall, which
could cause death, personal injury, and/or property damage. Winch cable length can be found on the
ALL1000 product sticker, shipping box and the front page of these installation instructions.

STEP 2

After turning o power, remove and discard existing electrical box if present in ceiling. Only use ceiling box
provided with ALL1000. See Diagram A.

Never remove an existing ceiling box while the power is connected. Electricity could cause death,
personal injury, and/or property damage.

STEP 3

Cut a 4 ½” (11.4cm) hole in ceiling for ceiling box. If you removed an existing ceiling box, existing hole may
need to be enlarged.

STEP 4

Attach conduit assembly to 3/4” conduit connector mounted below pulley. Once completely inserted,
tighten set screw on conduit connector. See Diagram A.

Never attach or adjust the conduit assembly improperly. is could interfere with the automatic shuto
system and could cause the chandelier to fall, which could cause death, personal injury, and/or property

damage.

Diagram A

3/4” Conduit Connector

Telescopic Conduit Assembly

ALL1000 Ceiling Box

STEP 5

Attach the 1/2” conduit connector on ceiling box to bottom of conduit assembly. Once completely inserted,
tighten set screw on conduit connector. See Diagram B.

Never attach or adjust the conduit assembly improperly. is could interfere with the automatic shuto
system and could cause the chandelier to fall, which could cause death, personal injury, and/or property
damage.

Diagram B

1/2” Conduit Connector

STEP 6

Tighten temporary 2.3Kg weight to xure coupler on bottom contact plate. Make sure jam nut on weight is
tight.

Never install or operate an ALL1000 before securing the temporary 2.3Kg weight to the xture coupler.
is could cause the temporary weight to fall, which could cause death, personal injury, and/or property
damage.