Customer Help Line: 01422 263313
Opening Hours: Mon-Fri 8am-8pm, Sat 9am-4pm, Sun 11am-4pm
Or visit our website at www.ekey.co.uk
APTUC1008PR
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
LIGHTNING FLASH WITH ARROWHEAD SYMBOL -
within an equilateral triangle, is intended to alert the
us e r t o th e pr e sen c e o f un i nsu l ate d da n ger o us
voltage within the products enclosure that may be of
sufficient m agn itu de to constitu de a r isk of electri c
shock to persons.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL -
CLA SS 1 LA SE R PRO DU CT
KLA SS 1 LA SE R APP AR AT
LUO KE N 1 L AI SERLA IT E
KLA SS E 1 L AS ER PR OD UKT
This label is attached to the place as illustrated to inform that the
apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION -
This label is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
EXCLAMATION POINT -
is used to indicate that a specific component shall be
replaced o nl y by t he c omponent spec if ie d in t ha t
documentation for safety reason.
within an equilateral triangle,
E-1
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The ap pl ia nce sho ul d be co nn ec ted to po wer sup pl y only of t he type d es cribed in the
operating instructions or as marked on the appliance.
9. GROUNDING - Precautions should be taken to ensure that the grounding means of an appliance is not defeated.
10. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
11. POWER LINES - An outdoor antenna should be located away from power lines.
12. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
13. ESD WARNING - The display does not function properly or no reaction to operation of any the control may due
14. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
15. SERVICING - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the power
back on.
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
E-2
LOCATION OF CONTROL
1.) VOLUME CONTROL
2.) FUNCTION
3.) REMOTE SENSOR
4.) STANDBY
5.) STANDBY INDICATOR
6.)
MUTE
7.)
USB / SD CARD SLOT DOOR
8.)
LCD DISPLAY
9.)
SKIP -
10.)
PLAY / PAUSE
11.)
SKIP +
12.)
STOP / BAND / USB / SD
13.)
MEMO UP / REPEAT
14.)
MONO / STEREO
15.)
FOLDER +
16.)
FOLDER -
17.)
MEMO / ADJ
BASS
18.)
19.)
SPEAKER JACKS ( L / R )
AM ANTENNA
20.)
FM ANTENNA
21.)
22.)
AC C
ORD
8 9 10
1
2
3
4
5
6
7
19
11
12
13
14
15
16
17
18
21
20
22
POWER SOURCE
AC POWER
You can power your appliance by plugging the AC power cord at the back of the appliance into a wall
AC power outlet. Check that the rated voltage of your appliance matches your local voltage.
E-3
1. STANDBY
2. MODE
3. SLEEP
4. 0 - 10
5. + 10
6. INFO MONO / ST.
7. SKIP +
8. STOP / BAND / USB / SD
9. SKIP -
10. RANDOM
11. BASS
12. MEMO / ADJ
13. VOL +
14. VOL -
15. P - DOWN
16. P - UP
17. TIMER
18. PLAY / PAUSE
19. REPEAT
20. EQ
21. INTRO
22. FUNCTION
23. MUTE
BATTERY INSTALLATION
REMOTE CONTROL
1
2
3
5
6
7
8
9
10
11
12 21
13
14
4
15
16
17
18
19
20
22
23
Insert 2 x “AAA” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid da mage to t he remote control. Always remove the batteries when the remote
control wi ll not be used for a long peri od of time, as this wil l cause leakage to the batteries and
subsequently damage to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new one.
SENSOR WINDOW OF THE RECEIVER
- Even if the remote control is operated within the effective range, its operation may be impossible if
there are any obstacies between the appliance and the remote control.
- If the remote control is operated near other appliances which generate infrared rays, or if other
remote control devices using infrared rays are used near the appliance, it may operate incorrectly.
E-4
RADIO OPERATION
AUTOMATIC TUNI
1. Press the “FUNCTION” button to select “TUNER” mo
2. Press the “STOP / BAND” button to select AM or FM.
3. Press the “SKIP +” or “SKIP -” button to start automatic tuning process.
4. When a station is tuned in the tuning process, it will stop automatically and you can listen to your
desired station.
NG
de.
MANUAL TUNING
It is for selecting stations, which cannot be tuned automatically. (manual selection)
To tune a channel manually.
- Skip step 4 in the above procedures.
- In step 3, each time the “SKIP +” or “SKIP -” button is pressed momentarily (0.5 second or less),
the frequency changes by a fixed step:
FM: 0.05 MHz steps
AM: 9 kHz steps
MEMORY PRESET
1. Repeat step 1 to 4 in the AUTOMATIC TUNING procedures.
2. Press the “MEMO / ADJ” button to start the preset process.
3. Display will show the memory sequence number and a flashing “1”.
4. Press the “P - UP” or “P - DOWN” button or the “MEMO / ADJ” button of front panel to determine
the preset station number.
5. Press again the “MEMO / ADJ” button to preset your desired station.
6. Once al l the s tations were p reset, press t he “P - UP” or “P-DOW N” butt on to l isten t o your
desired station.
MONO / STEREO
Press the “INFO MONO/ST.” button to achieve the best frequency.
E-5
CD / MP3 OPERATION
GENERAL OPERATIO
PLAY / PAUSE Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the sound.
STOP Press to stop all CD / MP3 operation.
N
PLAYBACK
1. Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
2. Close the CD door.
3. Press the “FUNCTION” button to select “CD / MP3” mode.
4. Focus search is performed if disc is inside.
Playback will start automatically from the first track.
5. Adjust the “VOLUME” control to the desired level
6. Press the “PLAY / PAUSE” button when you want to stop playback temporarily.
7. Press the “STOP” button when finished.
.
E-6
CD / MP3 OPERATION
PROGRAM
Be sure to press the “STOP” button before use.
1. Press the “MEMO / ADJ” button, the display will show “MEMORY” and “P00 000”.
2. Select desired track by using the “SKIP +” or “SKIP -” button. (You may select a desired album
by pressing the “FOLDER +” or “FOLDER -” button.)
3. Press the “MEMO / ADJ” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to play the
disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.
REPEAT
Press the “REPEAT” button during playing CD / MP3 disc,
each press switches the repeat function as follows:
1 - REPEAT 1
2 - REPEAT ALBUM ( For MP3 only )
3 - REPEAT ALL
4 - NORMAL PLAYBACK
REPEAT 1
REPEAT 1
REPEAT
ALBUM
REPEAT
ALBUM
NORMAL
AYBACK
PL
REPEAT
ALL
REPEAT
ALL
RANDOM
1
. Press the “RANDOM” button on remote control during playing disc, the appilance will select and
play a track randomly.
2. Press the “RANDOM” button again to terminate random mode.
E-7
USB / SD OPERATION
GENERAL OPE
PLAY / PAUSE Press to start playing tracks from the USB / SD card.
Press again to stop playing USB / SD operation temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the sound.
STOP Press to stop all USB / SD operation.
RATION
PLAYBACK
1. Plug or slot in USB / SD card device to the port. (Make sure no disc on disc tray)
2. Press the “FUNCTION” button to select “CD / MP3” mode.
3. Press and hold the “STOP / BAND / USB / SD” button for a few seconds to entry USB / SD mode.
4. Playback will start automatically from the first track.
5. Press the “STOP / BAND / USB / SD” button when finished.
6. Press the “PLAY / PAUSE” button again, playback will start from the first
track.
PROGRAM, MODE
The operation of PROGRAM, MODE are as the same as that of CD / MP3. Please refer to CD / MP3
OPERATION.
E-8
OTHER FEATURES
EQ
Press the “EQ” button on remote control, each press switch the EQ function as follows:
1 - CLASSIC
2 - ROCK
3 - POP
4 - JAZZ
5 - FLAT (NORMAL)
Notes:
- The player not responsible for playability of MP3 in any case. Due to recording condition such as PC
performance, writing software, media ability or etc.
- For CD-RW, CD-R, it may not be played according to the type of this disc.
EXTRA BASS
1. Press the “BASS” button on remote control to enjoy extra bass sound effect.
2. Display will show “BASS - ON”.
3. Press the “BASS” button again to switch off extra bass sound effect.
INTRO
1. Press the “INTRO” button during play disc to play each song for 15 seconds.
2. Press the “INTRO” button again to resume normal playback.
MUTE
1. Press the “MUTE” button to remove the sound during playing disc.
2. Press the “MUTE” button again to resume the sound.
E-9
OTHER FEATURES
SLEEP
1. Press the “SLEEP” button on remote control, display will show “SLEEP 90”. That means, after 90
minutes, appliance will automatically turn to standby mode.
2. Press the “SLEEP” button again to select the automatically turn off time, from 90, 80, 70, 60, 50,
40, 30, 20, 10 minutes.
3. Press the “SLEEP” button to “SLEEP 00” to canel sleep function.
CLOCK SETT
1. Press the “MODE” button to switch unit at clock mode.
2. Press the “MEMO / ADJ” button to entry clock set mode. The display will show “24H” and
flashing.
3. Adjust time format ( 12H / 24H ) by pressing the “SKIP +” or “SKIP -” button.
4. Press the “MEMO / ADJ” button to confirm time format, display will show “AM” or “PM” if 12H
format is set.
5. Adjust hour by pressing the “SKIP +” or “SKIP -” button, press the “MEMO / ADJ” button to confirm.
6. Adjust minute by pressing the “SKIP +” or “SKIP -” button, press the “MEMO / ADJ” button to confirm.
ING
TIMER SETTING
Timer setting must be after completed clock setting.
1. Press the “MODE” button twice on remote control to entry timer set mo
2. The display will show “TIMER ON”, press the “MEMO / ADJ” button to entry “TIMER ON” setting.
3. Adjust hour by pressing the “SKIP +” or “SKIP -” button, press the “MEMO / ADJ” button to confirm.
4. Adjust minute by pressing the “SKIP +” or “SKIP -” button, press the “MODE” button to confirm.
5. The display will show “TIMER OFF”, press the “MEMO / ADJ” button to entry “TIMER OFF” setting.
6. Adjust hour by pressing the “SKIP +” or “SKIP -” button, press the “MEMO / ADJ” button to confirm.
7. Adjust minute by pressing the “SKIP +” or “SKIP -” button, press the “MODE” button to confirm.
8. The display will show “TIMER”, set the source you want to play.
9. Press the “MEMO / ADJ” button to set desired mode ( TUNER / DISC / AUX ).
10.Press the “MODE” button to confirm timer setting.
11.Press the “TIMER” button on remote control to activate timer on / off function.
12.Press the “TIMER” button again on remote control to terminate timer setting.
de.
E-10
Loading...