AJA D5CE User Manual

D5CE Serial Digital

Encoder

User Manual

December 5, 2003 P/N 101635-00

2

Trademarks

AJA, Io, and Kona are trademarks of AJA Video, Inc. All other trademarks are the property of their
respective holders.

Notice

Copyright © 2003 AJA Video, Inc. All rights reserved. All information in this manual is subject to
change without notice. No part of the document may be reproduced or transmitted in any form,
or by any means, electronic or mechanical, including photocopying or recording, without the
express written permission of AJA Inc.

FCC Emission Information

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by AJA Video can effect emission compliance
and could void the user’s authority to operate this equipment.

Contacting Support

Limited Warranty

To contact AJA Video for sales or support, use any of the following methods:

443 Crown Point Circle, Grass Valley, CA. 95945 USA

Telephone: [phone] or +1.530.274.2048
Fax: [phone]

Web: http://www.aja.com
Support Email: [e-mail]
Sales Email: [e-mail]

When calling for support, have all information on the product (serial number etc.) at hand prior to
calling.

AJA Video warrants that this product will be free from defects in materials and workmanship for a period of five years

from the date of purchase. If a product proves to be defective during this warranty period, AJA Video, at its option, will
either repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the
defective product.

In order to obtain service under this warranty, you the Customer, must notify AJA Video of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. The Customer shall be responsible
for packaging and shipping the defective product to a designated service center nominated by AJA Video, with shipping
charges prepaid. AJA Video shall pay for the return of the product to the Customer if the shipment is to a location within
the country in which the AJA Video service center is located. Customer shall be responsible for paying all shipping charges,
insurance, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. AJA Video shall not be obligated to furnish service under this warranty a) to repair damage resulting
from attempts by personnel other than AJA Video representatives to install, repair or service the product, b) to repair
damage resulting from improper use or connection to incompatible equipment, c) to repair any damage or malfunction
caused by the use of non-AJA Video parts or supplies, or d) to service a product that has been modified or integrated with
other products when the effect of such a modification or integration increases the time or difficulty of servicing the
product.

THIS WARRANTY IS GIVEN BY AJA VIDEO IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED. AJA VIDEO AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AJA VIDEO’S RESPONSIBILITY TO
REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE WHOLE AND EXCLUSIVE REMEDY PROVIDED TO
THE CUSTOMER FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
IRRESPECTIVE OF WHETHER AJA VIDEO OR THE VENDOR HAS ADVANCE NOTICE OF THE
POSSIBILITY OF SUCH DAMAGES.

•

•

•

•

•

•

•

Introduction

Features

AJA D5CE Serial Digital Encoder User Manual — Introduction

The D5CE provides low cost, all digital conversion of SDI to either composite or
component analog video. Three analog BNC outputs are user configurable to cover a
wide range of format combinations including three composite, one composite and Y/
C, YPbPr (SMPTE, EBU-N10), Betacam, or RGB. The D5CE is useful for
monitoring video, level/phase checking, dubs, or desktop video applications. In
addition, an equalized and re-clocked SDI loop-through output is provided. The
D5CE automatically configures to 525 or 625 line component digital inputs and
then outputs analog NTSC (525 line input), PAL (625 line input) or component as
configured by the DIP switches.

The D5CE encodes the full dynamic range of input component video—values below
black and above white are not clipped. In the NTSC mode, the 7.5 IRE pedestal can

1

be disabled by the external DIP switch.

Low Cost SDI to Component or Composite Analog

User Selectable Component or Composite/YC Outputs

YPbPr, Betacam, or RGB Component Formats

Re-clocked Loop-Thru SDI Output

3

Block Diagram

Automatic NTSC/PAL Selection

User Selectable Vertical/Horizontal Blanking

External DIP switch user interface for configuration

DIP

Switch

User

Interface

for

Feature

Selection

Serial
Video

In

D/A

ReClock

Clocked Loop-through SDI Outputs

Converter

Filter

Filter

Filter

COMPOSITE or COMPONENT OUTPUTS
(selected by DIP switch)

1

2

3

COMP

Y

C

Serial Video Out

Y

G

Pb

B

Pr

R

D5CE SDI to Analog Component and Composite Converter, Block Diagram

4

I/O Connections

SDI Input

BNC

SDI Loop

Output

BNC

+ 5VDC

Composite
and
Component
Output BNCs

Configuration
Determined by
DIP switch on
other side of
Converter

Power

Input

D5CE, Side View

User Controls

AJA D5CE Serial Digital Encoder User Manual — User Controls

1
2
3
4
5
6
7
8

8

The user interface for the D5CE is a 4-switch DIP
accessible through a cut-out in the bottom of the
unit. Use the DIP switches to configure outputs,
pedestal, blanking, and choose type of component
output (if using component).

Switches 1 and 2 select output BNC video format.
Switches 3 and 4 configure pedestal and blanking.
The exact function of each DIP switch and what it

DIP Switches

OFF ON

controls is described on the following pages.

1

Switch 1—Selects Composite or Component Video Output (3 BNCs)

:

ON OFF

COMPNT:
Selects component video output

CMPSTE:
Selects composite video output and Y/C output

5

Switch 2—Select Video Format of Outputs (3 BNCs)

:

ON OFF

YPbPr/YC:
If SW1 is set to COMPNT, this selection
outputs
Y, R-Y, B-Y
If SW 1 is set to CMPSTE, this selection
outputs 1 composite and 1 Y/C

RGB:
If SW1 is set to COMPNT, this selection outputs
RGB
If SW1 is set to CMPSTE, this selection outputs 3
composites

Switch 3—Configure Pedestal

:

ON OFF, RGB

7.5 IRE pedestal for NTSC (also selects
BETA 525 levels for YUV)

Note:

There is no effect with 625 input.

No pedestal (also selects SMPTE levels for YUV)

6

Switch 4—Configure Blanking For Composite/Sync BNC

:

ON OFF

Output Selection
Matrix For Output
2 (3 BNCs)

WIDE Blanking:
Vertical—
Line numbers indicate where video starts)
line 20, field 1; line 20, field 2 (525 line)
line 23, field 1; line 336, field 2 (625 line)
Horizontal—
Active video line duration
ITU-R/SMPTE (710 pixels NTSC,
702 pixels PAL)

NARROW (NAR) Blanking:
Vertical—
Line numbers indicate where video starts
line 13, field 1; line 12, field 2 (525 line)
line 10, field 1; line 322, field 2 (625 line)
Horizontal—
Active video line duration's)
ITU-R.470 (720 pixels PAL/NTSC)

The following table shows the combinations of DIP switch settings required to configure
the three output BNCs.

Output Format

3 composite (pedestal) CMPSTE/

3 composite (no pedestal) CMPSTE/

1 composite & 1 Y/C (pedestal) CMPSTE/

DIP Switch#1DIP Switch#2DIP Switch

#3

OFF

OFF

OFF

RGB/OFF ON

RGB/OFF OFF

YUV/YC

ON

ON

1 composite & 1 Y/C (no pedestal) COMPNT/ON YUV/YC

ON

RGB COMPNT/ON RGB/OFF OFF

SMPTE component (BETA625) COMPNT/ON YUV/YC

ON

BETA 525 component COMPNT/ON YUV/YC

ON

OFF

OFF

ON

Notes:

1. The D5CE is programmed for a 1.3 MHz chroma bandwidth when composite video
mode is selected. This provides the best quality video when encoding component
digital video. However, with lower cost monitors it may be desirable to reduce the
composite chroma bandwidth to 650 Khz to reduce the effects of cross-color artifacts.
This option is available from AJA Video as a special order.

2. The encoder’s D-to-A chip in the D5CE has an 8-bit input for component digital
video and 10-bit D-to-A converters for the analog outputs. This configuration is often
described as an 8-bit “signal path” and 10-bit “Quantization.” Due to the internal
processing of the encoder chip, it is advantageous to use 10-bit D-to-A converters at the
output even though the input is 8-bits.

1.

2.

3.

4.

Installation

Specifications

AJA D5CE Serial Digital Encoder User Manual — Installation

Typically, D5CE installation consists of the following:

disconnect +5VDC from the convertor

configure the DIP switch for the desired equipment configuration and video formats

connect video equipment to the convertor BNCs

apply +5VDC power to the converter (AJA power supply model DWP)

1

Item Specification

Serial Input SMPTE 259M 270MB, (SDI)

SDI Cable Equalization 300 meter 8281 typical

Serial Output (looping) Equalized, Re-clocked

Outputs 1. YPbPr - SMPTE, EBU-N10, Betacam, RGB (3 BNCs)

2. NTSC, PAL (3 BNCs)

3. NTSC/PAL and Y/C (3 BNCs)

7

Frequency Response +/-.25dbto 5.5Mhz (Y)

2T K factor < 1% (Y)

Differential Gain < 1 .5%

Differential Phase < 1 .5 degree

Y/C delay 10ns maximum

D/A Converters 10 bits

Signal Path 8 bits

Delay (input to output) 1.5us

Output level adjustment +/- 20% (internal)

Output level matching 1 .5% or 10mv (All outputs are separately buffered)

Power
(AJA power supply model DWP)

Size 5.1" x 2.4" x 1" (131 x 61 x 25 MM.)

+/-.25dbto2.0Mhz (Chroma-Component, RGB)
+/-.25dbto 1.3Mhz (Chroma - Composite)

5v DC regulated, 2.5 watt

8