AJA D10CE User Manual

D10CE 10-bit Encoder
SDI to Analog Converter
User Manual
August 25, 2003 P/N 101641-00
2
Trademarks
AJA, Io, and Kona are trademarks of AJA Video, Inc. All other trademarks are the property of their respective holders.
Notice
Copyright © 2003 AJA Video, Inc. All rights reserved. All information in this manual is subject to change without notice. No part of the document may be reproduced or transmitted in any form, or by any means, electronic or mechanical, including photocopying or recording, without the express written permission of AJA Inc.
FCC Emission Information
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by AJA Video can effect emission compliance and could void the user’s authority to operate this equipment.
Contacting Support
Limited Warranty
To contact AJA Video for sales or support, use any of the following methods:
443 Crown Point Circle, Grass Valley, CA. 95945 USA
Telephone: +1.800.251.4224 or +1.530.274.2048 Fax: +1.530.274.9442
Web: http://www.aja.com Support Email: support@aja.com Sales Email: sales@aja.com
When calling for support, have all information on the product (serial number etc.) at hand prior to calling.
AJA Video warrants that this product will be free from defects in materials and workmanship for a period of five years
from the date of purchase. If a product proves to be defective during this warranty period, AJA Video, at its option, will either repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, you the Customer, must notify AJA Video of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. The Customer shall be responsible for packaging and shipping the defective product to a designated service center nominated by AJA Video, with shipping charges prepaid. AJA Video shall pay for the return of the product to the Customer if the shipment is to a location within the country in which the AJA Video service center is located. Customer shall be responsible for paying all shipping charges, insurance, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. AJA Video shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than AJA Video representatives to install, repair or service the product, b) to repair damage resulting from improper use or connection to incompatible equipment, c) to repair any damage or malfunction caused by the use of non-AJA Video parts or supplies, or d) to service a product that has been modified or integrated with other products when the effect of such a modification or integration increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY AJA VIDEO IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. AJA VIDEO AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AJA VIDEO’S RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE WHOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER AJA VIDEO OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Introduction
Features
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — Introduction
The D10CE converts Component Serial Digital (SDI) to analog Composite and Component outputs—simultaneously. Four analog outputs are provided, plus two equalized and re-clocked SDI loop-through outputs. The D10CE automatically detects and configures to 525 or 625 line component digital input and then outputs analog NTSC (525 line input), PAL (625 line input) or component as configured by an 8-section DIP switch.
The full dynamic range of input component video values, below black and above white, are not clipped when the D10CE encodes. When the D10CE is in its NTSC mode, the 7.5 IRE pedestal can be disabled by DIP switch selection.
The component and composite outputs incorporate optimum chroma filtering and independent pedestal configuration. An exclusive PLL jitter filter/memory reduces the effects of SDI jitter on the output analog video. This feature, along with the precision 4x oversampled D/A filters, provides high quality analog outputs, with very low phase noise in the composite outputs.
High quality 10-bit encoding, 4 times oversampling
1
3
SDI Input, SMPTE 259M
Two loop-through SDI outputs (SMPTE 259M) (equalized and re-clocked copies of the SDI input)
Four analog outputs (configurable as 1 composite or sync, and R/G/B, Y/Pb/Pr, or Y/C)i.
Y/Pb/Pr selectable for SMPTE/EBU levels or Betacam levels (Y, R-Y, B-Y)
Composite NTSC or PAL
Configurable pedestal
Digital noise reduction
External DIP switch user interface for configuration
4
Block Diagram
DIP
Switch
User
Interface
for
Feature
Selection
Serial Video
In
10-bit D/A
ReClock
Clocked Loop-through SDI Outputs
Converter
PLL Jitter Filter
Filter
Filter
Filter
Filter
COMPOSITE or SYNC
COMPONENT OUTPUTS (selected by DIP switch)
Y
B
COMP
Pb
G
Y
Pr
R
C
I/O Connections
SDI Input
BNC
SDI Loop Output 1
BNC
SDI Loop Output 2
BNC
Serial Video Out 1
Serial Video Out 2
D10CE 10-bit SDI to Analog Component and Composite Converter, Block Diagram
Composite and Component Output BNCs
Configuration Determined by DIP switch on other side of Converter
+ 5VDC
Power
Input
D10CE, Side View
User Controls
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — User Controls
1 2 3 4 5 6 7 8
8
The user interface for the D10CE is an 8-switch DIP accessible through a cut-out in the bottom of the unit. Use the DIP switches to configure outputs, pedestal, blanking, and enable or disable noise reduction.
Switches 1 through 3 control the COMPOSITE/ SYNC output BNC. Switches 4 through 8 control the video format of the three BNCs below. The exact function of each DIP switch and what it controls is described on the following pages.
1
DIP Switches
OFF ON
Switch 1 Selects VIDEO or SYNC output from the Composite/Sync BNC
:
5
ON OFF
Selects SYNC output for Component output (use when the device being fed the component signal requires a separate sync signal)
Selects composite video out
Switch 2 Configure Pedestal For Composite/Sync BNC
:
ON OFF
Note:
7.5 IRE pedestal for NTSC (also selects BETA 525 levels for YPbPr)
There is no effect with 625 input.
No pedestal (also selects SMPTE levels for YPbPr)
6
Switch 3 Configure Blanking For Composite/Sync BNC
:
ON OFF
WIDE Blanking: Vert ical— Line numbers indicate where video starts) line 20, field 1; line 20, field 2 (525 line) line 23, field 1; line 336, field 2 (625 line) Horizontal— Active video line duration ITU-R/SMPTE (710 pixels NTSC, 702 pixels PAL)
NARROW (NAR) Blanking: Vert ical— Line numbers indicate where video starts line 13, field 1; line 12, field 2 (525 line) line 10, field 1; line 322, field 2 (625 line) Horizontal— Active video line duration's) ITU-R.470 (720 pixels PAUNTSC)~-
Switch 4 Select Composite (CMPSTE) or Component (COMPNT) Out
:
ON OFF
COMPNT: Selects component video output
CMPSTE: Selects composite video output
Switch 5 Select Video Format of Component Outputs
:
ON OFF
YUVNC: Selects YPbPr/YC component output, if SW1 is set to “COMPNT,”
Switch 6 Configure Pedestal For Component Output BNCs (3)
:
ON OFF
7.5 IRE pedestal for NTSC (also selects BETA 525 levels for YPbPr)
Note:
There is no effect with 625 input.
No pedestal (also selects SMPTE levels for YPbPr)
RGB: Selects RGB component output, if SW1 is set to “COMPNT”
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — User Controls
Switch 7 Configure Blanking For Component Output BNCs (3)
:
ON OFF
WIDE Blanking: Vert ical— Line numbers indicate where video starts) line 20, field 1; line 20, field 2 (525 line) line 23, field 1; line 336, field 2 (625 line) Horizontal— Active video line duration ITU-R/SMPTE (710 pixels NTSC, 702 pixels PAL)
NARROW (NAR) Blanking: Vert ical— Line numbers indicate where video starts line 13, field 1; line 12, field 2 (525 line) line 10, field 1; line 322, field 2 (625 line) Horizontal— Active video line duration's) ITU-R.470 (720 pixels PAUNTSC)~-
1
Switch 8 Configure Digital Noise Reduction
:
ON OFF
Enables Digital Noise Reduction on input. Disables Digital Noise Reduction
7
Output Selection Matrix For Output 2 (3 BNCs)
The following table shows the combinations of DIP switch settings required to configure the three BNCs below the COMPOSITE/SYNC BNC.
Output Format
1 Composite and 1 Y/C (Pedestal) CMPSTE N/A ON
1 Composite and 1 Y/C (no pedestal) CMPSTE N/A OFF
RGB COMPNT RGB OFF
RGB with pedestal COMPNT RGB ON
SMPTE component (BETA625)/ EBU-N10
BETA 525 component COMPNT YPbPr/YC ON
DIP Switch#4DIP Switch#5DIP Switch
#6
COMPNT YPbPr/YC OFF
8
Installation
Specifications
1.
2.
3.
4.
Typically, D10CE installation consists of the following:
disconnect +5VDC from the convertor
configure the DIP switch for the desired equipment configuration and video formats
connect video equipment to the convertor BNCs
apply +5VDC power to the converter ((AJA power supply model DWP)
Item Specification
Serial Input SMPTE 259M 270MB, (SDI)
SDI Cable Equalization 300 meter 8281 typical
Serial Outputs Equalized, Re-clocked
Frequency Response +/- .15dB to 5.5MHz (Y)
2T K factor < 0.5% (Y)
Differential Gain < 1 .5%
Differential Phase < 1 .5 degree
Y/C delay 10ns maximum
D/A Converters 10 bits, 4X oversampling
Signal Path 10 bits
Delay (input to output) 2.5us
Output level adjustment +/- 20% (internal)
Output level matching 1 .5% or 10mv (All outputs are separately buffered)
Power (AJA power supply model DWP)
Size 147 x 79 x 25 mm
+/- .15dB to 2.5MHz (Chroma - Component, RGB) +/- .15dB to 1.3MHz (Chroma - Composite)
5v DC regulated, 4 watt
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — Specifications
1
9
10
Loading...