• This Service Manual is the “Revision Publishing” and replaces “Simple
Manual” NSX-AJ10(U)/NSX-SZ10(LH), (S/M Code No. 09-99C-424-8T1).
• If requiring information about the CD mechanism, see Service Manual
of AZG-1 ZD8RNDM, (S/M Code No. 09-001-335-3N6) and
AZG-1 ZD8RNDC, (S/M Code No. 09-001-335-3NA).
10 W + 10 W
(50 Hz to 20 kHz, T.H.D. 1 %, 6 ohms)
Reference
15 W + 15 W
(1 kHz, T.H.D. 10 %, 6 ohms)
DIN AUDIO)
ohms or more
PHONES (stereo jack): accepts
headphones of 32 ohms or more
x 1, erase head x 1
Deck 2 : Playback head x 1
<Compact disc player section>
LaserSemiconductor laser (λ =780 nm)
D-A converter1 bit dual
Signal-to-noise ratio85 dB (1 kHz, 0 dB)
Harmonic distortion0.05 % (1 kHz, 0 dB)
<Speaker system SX-NAJ12>
Speaker System2 way, bass reflex (magnetic
shielded type)
Speaker unitsWoofer:
120 mm cone type
Tweeter:
20mm ceramic type
Impedance6 ohms
Sensitivity86 dB/W/m
Dimensions (W x H x D)220 x 324 x 235 mm
Weight2.0 kg
<General>
Power requirements120 V AC, 60 Hz
Power consumption38 W
Power consumptionWith power-economizing
in standby modemode off : 8.0 W
With power-economizing
mode on : 0.9 W
Dimensions of main unit260 x 324 x 346 mm
(W x H x D)
Weight of main unit5.7 kg
• Design and specifications are subject to change without notice.
– 2 –
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid expo-
sure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit-
tävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
(KSM-880CAB)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
PICK-UP Assy P.C.B
solder
– 3 –
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
1
1 Remove the AC power cord.
2
2 Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3
3 Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V)Discharging
(C101, 102)resistor (Ω)
25-48100387-A00-247-090
49-140220587-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W)Parts number
MAIN C.B
D101
3
C101C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
1 Turn on the AC main power.
2
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
– 4 –
Loading...
+ 8 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.