NSX-VC920
HR(S)
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
SYSTEM
NSX-VC920 RC-BAS08 VS
This Service Manual is the Revision Publishing and replaces Simple Manual
of NSX-VC920 (HR), (S/M Code No. 09-01A-446-8T1).
If requiring information about the CD mechanisim, see Service Manual of BZG-5,
(S/M Code No. 09-00C-353-3N8).
CD
CASSEIVER
CX-NVC920
BASIC TAPE MECHANISM : 2ZM-3MK2 PR7NM
BASIC CD MECHANISM : BZG-5 MVSD3N1DM
SPEAKER
SX-WNSZ900
SX-S85
REMOTE
CONTROLLER
S/M Code No. 09-01C-446-8R1
REVISION
DATA
SPECIFICATIONS
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)
<MW tuner section>
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<SW tuner section>
Tuning range 5.73 MHz – 17.9 MHz
Usable sensitivity 40 µV/m (IEC)
Antenna Wire antenna
<Amplifier section>
Main amplifier
Power output Rated: 144 W + 144 W
(6 ohms, T.H.D. 1 %, 1 kHz )
Reference: 180 W + 180 W
(6 ohms, T.H.D. 10 %, 1 kHz )
Total harmonic distortion 0.1 % (90 W, 1 kHz, 6 ohms,
DIN AUDIO)
Satellite amplifier
Power output Rated: 16 W + 16 W
(8 ohms, T.H.D. 1 %, 1 kHz )
Reference: 20 W + 20 W
(8 ohms, T.H.D. 10 %, 1 kHz )
Total harmonic distortion 0.2 % (8 W, 1 kHz, 8 ohms,
DIN AUDIO)
Inputs VIDEO/AUX: 300 mV (adjustable)
MD: 300 mV (adjustable)
MIC 1, MIC 2: 1.0 mV (10 kohms)
Outputs SPEAKERS: 6 ohms or more
SATELLITE SPEAKERS:
8 ohms or more
SUB WOOFERS: 1.0 V
LINE OUT: 210 mV
VIDEO OUT: 1.0 Vp-p (75 ohms)
CD DIGITAL OUT (OPTICAL)
PHONES: 32 ohms or more
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response CrO2 tape: 50 Hz – 16 kHz
Normal tape: 50 Hz – 15 kHz
Recording system AC bias
Heads Deck 1: Playback x 1
Deck 2: Recording/playback x 1,
erase x 1
<Disc player section>
Laser Semiconductor laser (l = 780 nm)
D/A converter 1 bit dual
Signal-to-noise ratio 90 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
Video signal NTSC/PAL color system (selectable)
Video data MPEG 1
Audio data MPEG 1, Layer 2 (VCD)
MPEG 1, Layer 3 (MP3-CD)
<General>
Power requirements 120 V/ 220 V – 230 V/ 240 V AC
(Switchable), 50/60 Hz
Power consumption 210 W
Power consumption With ECO mode on: 0.6 W
in standby mode With ECO mode off: 30 W
Dimensions (W x H x D) 260 x 326 x 394 mm
Weight 10.0 kg
<Main speakers SX-WNSZ900>
Speaker system 3 way, Built-in subwoofer
(magnetic shielded type)
Speaker units Subwoofer: 200 mm cone type
Full range: 100 mm cone type
Super tweeter: 20 mm ceramic type x 2
Impedance 6 ohms
Dimensions (W x H x D) 240 x 324 x 294 mm
Weight 5.4 kg
<Satellite speakers SX-S85>
Speaker system Full range (magnetic shielded type)
Speaker units 80 mm cone type
Impedance 8 ohms
Sensitivity 87 dB/W/m
Dimensions (W x H x D) 100 x 325 x 95 mm (with pedestal)
100 x 186 x 84 mm (without pedestal)
Weight 0.6 kg
• Design and specifications are subject to change without
notice.
• The word “BBE” and the “BBE symbol” are trademarks of BBE
Sound, Inc.
Under license from BBE Sound, Inc.
– 2 –
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP Assy PWB
Solder
– 3 –
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
FRONT C.B
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
15
C113
Short with tweezers.
Fig-2-2
C113
%
*
VSS
VDD
MICROCOMPUTER
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
ELECTRICAL MAIN PARTS LIST
PART NO.
NO.
IC
8B-NH6-601-030 C-IC,LC876670B-5Y60
87-A21-911-040 C-IC,M61515FP
87-A21-023-040 C-IC,BA3835F
87-A21-831-010 IC,SPS-422-1-F1
87-A21-948-030 C-IC,BD3877KS2
87-A21-695-010 IC,LA1845L
87-A21-928-010 IC,LC72131D-N
87-A20-783-040 C-IC,BA7762AFS
87-A21-018-040 C-IC,M65849BFP631D
87-A21-269-010 IC,EW732
TRANSISTOR
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-186-010 FET,2SK3053
87-A30-484-080 C-TR,KRA102S
87-A30-190-080 TR,CC5551
87-A30-204-010 TR,2SD2439
87-A30-205-010 TR,2SB1588
87-A30-086-040 C-TR,CSD1306E
87-026-609-080 TR,KTA1266GR
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-087-080 C-FET,2SK2158
87-A30-256-010 TR,2SD1933
87-A30-255-010 TR,2SB1342
87-A30-071-080 C-TR,RT1N 144C
87-A30-495-080 TR,2SA1981Y
87-A30-074-080 C-TR,RT1P 141C
87-026-225-080 C-FET,2SJ106GR
87-A30-494-080 TR,2SA1980G
87-026-610-080 TR,KTC3198GR
87-A30-063-080 C-TR,KRA104S
87-A30-521-080 C-TR,2SC5345SF/S(O)
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E
89-327-143-080 C-TR,2S2714O
87-A30-200-080 TR,2SA1585SR
87-A30-196-080 TR,2SC4115SRS
87-A30-663-040 C-TR,2SB792A(RS)
87-A30-662-040 C-TR,2SD814A(RS)
89-213-702-010 TR,2SB1370E
87-A30-216-080 TR,2SA933AS(R)
DIODE
87-017-149-080 ZENER,HZS6A2L
87-A40-291-080 DIODE,1N4148M (CPT)
87-A40-673-090 DIODE,D10XB20
87-A40-646-010 DIODE,FMB-G16L
87-A40-747-080 ZENER,UZ5.1BSB
87-A40-749-080 ZENER,UZ5.6BSB
87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-764-080 ZENER,UZ10BSC
87-A40-488-080 DIODE,1SS244
87-A40-739-080 ZENER,UZ2.7BSA
87-A40-748-080 ZENER,UZ5.6BSA
87-A40-769-080 ZENER,UZ18BSB
87-A40-802-080 ZENER,UZ5.1BSC
87-A40-781-080 ZENER,UZ36BSA
87-A40-553-080 DIODE,1N4003 LES
87-A40-745-080 ZENER,UZ4.7BSA
87-A40-530-080 DIODE,RB721Q-40
87-A40-768-080 ZENER,UZ16BSA
MAIN C.B
C11 87-012-368-080 C-CAP,S 0.1-50 Z F
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C12 87-012-368-080 C-CAP,S 0.1-50 Z F
C13 87-012-368-080 C-CAP,S 0.1-50 Z F
C14 87-012-368-080 C-CAP,S 0.1-50 Z F
C21 87-A12-780-090 CAP,E 4700-35 M 85 SKR
C22 87-A12-780-090 CAP,E 4700-35 M 85 SKR
C23 87-A10-231-090 CAP,E 3300-80
C24 87-A10-231-090 CAP,E 3300-80
C31 87-A12-062-080 CAP,E 100-10 SMG
C32 87-012-286-080 C-CAP,U 0.01-25 K B
C33 87-A12-071-080 CAP,E 47-25 SMG
C34 87-015-697-080 CAP,E 3.3-50 M 7L SRA
C35 87-012-286-080 C-CAP,U 0.01-25 KB
C36 87-A12-062-080 CAP,E 100-10 SMG
C37 87-A12-072-080 CAP,E 100-25 SMG
C38 87-A12-092-080 CAP,E 22-50 SMG
C39 87-A12-067-080 CAP,E 330-16 SMG
C40 87-A12-074-080 CAP,E 470-25 SMG
C101 87-012-276-080 C-CAP,U 1500P-50 K B
C102 87-012-276-080 C-CAP,U 1500P-50 K B
C103 87-012-368-080 C-CAP,S 0.1-50 Z F
C104 87-012-368-080 C-CAP,S 0.1-50 Z F
C105 87-012-368-080 C-CAP,S 0.1-50 Z F
C106 87-012-368-080 C-CAP,S 0.1-50 Z F
C107 87-A12-921-080 C-CAP,S 0.01-250 K X7R
C108 87-A12-921-080 C-CAP,S 0.01-250 K X7R
C109 87-010-759-080 C-CAP,U 0.1-25 Z F
C110 87-010-759-080 C-CAP,U 0.1-25 Z F
C117 87-010-759-080 C-CAP,U 0.1-25 Z F
C118 87-010-759-080 C-CAP,U 0.1-25 Z F
C123 87-010-759-080 C-CAP,U 0.1-25 Z F
C124 87-010-759-080 C-CAP,U 0.1-25 Z F
C125 87-010-759-080 C-CAP,U 0.1-25 Z F
C126 87-010-759-080 C-CAP,U 0.1-25 Z F
C128 87-010-759-080 C-CAP,U 0.1-25 Z F
C129 87-A12-319-080 C-CAP,U 0.1-25 K B
C130 87-012-274-080 C-CAP,U 1000P-50 K B
C131 87-A12-087-080 CAP,E 1-50 SMG
C132 87-A12-090-080 CAP,E 4.7-50 SMG
C133 87-A12-071-080 CAP,E 47-25 SMG
C301 87-012-188-080 C-CAP,U 47P-50 CH
C302 87-012-188-080 C-CAP,U 47P-50 CH
C303 87-012-336-080 C-CAP,U 330P-50 J SL
C304 87-012-336-080 C-CAP,U 330P-50 J SL
C305 87-012-336-080 C-CAP,U 330P-50 J SL
C306 87-012-336-080 C-CAP,U 330P-50 J SL
C307 87-A10-262-080 C-CAP,U 1-10 Z F
C309 87-A10-260-080 C-CAP,U 0.1-16 K B
C310 87-A10-260-080 C-CAP,U 0.1-16 K B
C311 87-010-787-080 CAP,U 0.022-25 K B
C312 87-010-787-080 CAP,U 0.022-25 K B
C313 87-012-276-080 C-CAP,U 1500P-50 B
C314 87-012-276-080 C-CAP,U 1500P-50 B
C315 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C316 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C321 87-A10-828-080 C-CAP,U 0.33-6.3 K B
C322 87-A10-828-080 C-CAP,U 0.33-6.3 K B
C324 87-A12-071-080 CAP,E 47-25 SMG
C325 87-A12-057-080 CAP,E 330-6.3 SMG
C327 87-A12-090-080 CAP,E 4.7-50 SMG
C328 87-A12-090-080 CAP,E 4.7-50 SMG
C332 87-A10-262-080 C-CAP,U 1-10 Z F
C335 87-A12-087-080 CAP,E 1-50 SMG
C336 87-A12-087-080 CAP,E 1-50 SMG
C337 87-010-831-080 C-CAP,U 0.1-16 Z F
C339 87-010-831-080 C-CAP,U 0.1-16 Z F
C340 87-010-831-080 C-CAP,U 0.1-16 Z F
C351 87-A10-039-080 C-CAP,U 470P-50 J CH
C352 87-A10-039-080 C-CAP,U 470P-50 J CH
C354 87-010-175-080 C-CAP,S 560P-50 J SL
C355 87-012-274-080 CHIP CAP,U 1000P-50B
DESCRIPTIONREF. NO. KANRI
6
PART NO.
NO.
C356 87-A12-071-080 CAP,E 47-25 SMG
C357 87-012-286-080 CAP,U 0.01-25
C358 87-012-279-080 C-CAP,U 2700P-50 B
C359 87-012-279-080 C-CAP,U 2700P-50 B
C360 87-012-279-080 C-CAP,U 2700P-50 B
C363 87-A12-361-080 CAP,M 5600P-100 J CP
C370 87-010-831-080 C-CAP,U 0.1-16 Z F
C373 87-A10-794-080 C-CAP,U 0.15-16 Z F
C374 87-A10-794-080 C-CAP,U 0.15-16 Z F
C378 87-010-831-080 C-CAP,U 0.1-16 Z F
C379 87-A12-069-080 CAP,E 22-25 SMG
C380 87-A12-069-080 CAP,E 22-25 SMG
C381 87-012-286-080 CAP,U 0.01-25
C382 87-012-176-080 C-CAP,U 15P-50 J CH
C383 87-012-286-080 CAP, U 0.01-25
C384 87-A12-088-080 CAP,E 2.2-50 SMG
C386 87-010-831-080 C-CAP,U 0.1-16 Z F
C387 87-012-335-080 C-CAP,U 270P-50 J SL
C388 87-012-279-080 C-CAP,U 2700P-50 K B GRM
C391 87-012-337-080 C-CAP,U 56P-50 J CH GRM
C392 87-012-337-080 C-CAP,U 56P-50 J CH GRM
C393 87-012-337-080 C-CAP,U 56P-50 J CH GRM
C394 87-012-337-080 C-CAP,U 56P-50 J CH GRM
C501 87-A12-062-080 CAP,E 100-10 SMG
C502 87-010-831-080 C-CAP,U 0.1-16 Z F
C503 87-A10-353-080 C-CAP,U 0.22-10KB
C504 87-A10-353-080 C-CAP,U 0.22-10KB
C505 87-A10-025-080 C-CAP,U 0.22-16Z F
C506 87-012-280-080 CAP,U 3300P-50
C507 87-010-986-080 C-CAP,S 820P-25 J CH
C508 87-A10-260-080 C-CAP,U 0.1-16 K B
C509 87-A10-260-080 C-CAP,U 0.1-16 K B
C510 87-012-280-080 CAP,U 3300P-50
C511 87-010-986-080 C-CAP,S 820P-25 J CH
C512 87-A10-025-080 C-CAP,U 0.22-16Z F
C513 87-A12-083-080 CAP,E 0.1-50 SMG
C514 87-A12-061-080 CAP,E 47-10 SMG
C515 87-A12-087-080 CAP,E 1-50 SMG
C516 87-A12-087-080 CAP,E 1-50 SMG
C517 87-012-279-080 C-CAP,U 2700P-50 B
C518 87-012-279-080 C-CAP,U 2700P-50 B
C531 87-A12-091-080 CAP,E 10-50 SMG
C532 87-010-831-080 C-CAP,U 0.1-16 Z F
C533 87-010-831-080 C-CAP,U 0.1-16 Z F
C534 87-012-199-080 C-CAP,U 220P-50 J CH
C535 87-012-274-080 CHIP CAP,U 1000P-50B
C536 87-010-831-080 C-CAP,U 0.1-16 Z F
C537 87-012-188-080 C-CAP,U 47P-50 CH
C538 87-012-188-080 C-CAP,U 47P-50 CH
C539 87-012-188-080 C-CAP,U 47P-50 CH
C541 87-012-274-080 CHIP CAP,U 1000P-50B
C609 87-012-277-080 C-CAP, U 1800P-50 B
C610 87-012-277-080 C-CAP, U 1800P-50 B
C611 87-010-956-080 CHIP-CAP,S 0.068-25B
C612 87-A11-070-080 C-CAP,U 0.033-16 K B
C613 87-012-286-080 C-CAP,U 0.01-25
C614 87-012-286-080 C-CAP,U 0.01-25
C615 87-A10-260-080 C-CAP,U 0.1-16 K B
C616 87-A10-260-080 C-CAP,U 0.1-16 K B
C617 87-010-829-080 C-CAP,U 0.047-16
C618 87-A12-087-080 CAP,E 1-50 SMG
C619 87-A12-062-080 CAP,E 100-10 SMG
C620 87-012-280-080 C-CAP,U 3300P-50 K B
C623 87-A12-087-080 CAP,E 1-50 SMG
C624 87-A12-087-080 CAP,E 1-50 SMG
C626 87-A12-062-080 CAP,E 100-10 SMG
C627 87-A12-086-080 CAP,E 0.47-50 SMG
C628 87-A12-086-080 CAP,E 0.47-50 SMG
C629 87-A10-504-080 C-CAP,U 0.047-16 K B
C630 87-A10-504-080 C-CAP,U 0.047-16 K B
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C631 87-012-281-080 C-CAP,U 3900P-50 B
C632 87-012-281-080 C-CAP,U 3900P-50 B
C633 87-010-831-080 C-CAP,U 0.1-16 Z F
C634 87-010-831-080 C-CAP,U 0.1-16 Z F
C635 87-A12-376-080 CAP,M 0.1-100 J CP
C636 87-A12-376-080 CAP,M 0.1-100 J CP
C637 87-A12-376-080 CAP,M 0.1-100 J CP
C638 87-A12-376-080 CAP,M 0.1-100 J CP
C639 87-A12-091-080 CAP,E 10-50 SMG
C641 87-A12-085-080 CAP,E 0.33-50 SMG
C642 87-A12-085-080 CAP,E 0.33-50 SMG
C643 87-010-831-080 C-CAP,U 0.1-16F
C644 87-A12-087-080 CAP,E 1-50 SMG
C647 87-A12-088-080 CAP,E 2.2-50 SMG
C648 87-A12-088-080 CAP,E 2.2-50 SMG
C665 87-010-176-080 C-CAP,S 680P-50 J SL
C666 87-010-176-080 C-CAP,S 680P-50 J SL
C671 87-012-195-080 C-CAP,U 100P-50CH
C672 87-012-195-080 C-CAP,U 100P-50CH
C673 87-012-286-080 CAP,U 0.01-25
C674 87-010-759-080 C-CAP,U 0.1-25 Z F
C675 87-A10-712-080 C-CAP,S 0.22-50 Z F
C677 87-A12-085-080 CAP,E 3.3-50 SMG
C678 87-A12-085-080 CAP,E 3.3-50 SMG
C679 87-010-831-080 C-CAP,U 0.1-16 Z F
C680 87-012-286-080 C-CAP,U 0.01-25
C682 87-010-831-080 C-CAP,U 0.1-16 Z F
C698 87-012-195-080 C-CAP,U 100P-50 J CH
C699 87-012-195-080 C-CAP,U 100P-50CH
C771 87-A12-062-080 CAP,E 100-10 SMG
C772 87-012-286-080 CAP, U 0.01-25
C779 87-012-278-080 C-CAP,U 2200P-50 K B
C780 87-012-278-080 C-CAP,U 2200P-50 K B
C782 87-012-286-080 C-CAP, U 0.01-25
C783 87-012-286-080 C-CAP, U 0.01-25
C784 87-012-286-080 C-CAP, U 0.01-25
C785 87-012-286-080 C-CAP, U 0.01-25
C786 87-012-286-080 C-CAP, U 0.01-25
C788 87-A10-592-080 C-CAP,S 0.015-50 J B
C789 87-A10-592-080 C-CAP,S 0.015-50 J B
C790 87-016-116-080 C-CAP,U 0.015-25 J B CB
C791 87-010-831-080 C-CAP,U 0.1-16F
C792 87-012-286-080 C-CAP, U 0.01-25
C793 87-A12-090-080 CAP,E 4.7-50 SMG
C795 87-012-286-080 C-CAP, U 0.01-25
C796 87-012-286-080 C-CAP, U 0.01-25
C797 87-A12-091-080 CAP,E 10-50 SMG
C798 87-012-286-080 C-CAP, U 0.01-25
C799 87-A12-065-080 CAP,E 33-16 SMG
C800 87-010-829-080 C-CAP, U 0.047-16 F
C801 87-A12-089-080 CAP,E 3.3-50 SMG
C802 87-010-829-080 C-CAP, U 0.047-16 F
C803 87-010-787-080 C-CAP, U 0.022-25 B
C804 87-A12-062-080 CAP,E 100-10 SMG
C807 87-A12-086-080 CAP,E 0.47-50 SMG
C808 87-A12-087-080 CAP,E 1-50 SMG
C809 87-A12-087-080 CAP,E 1-50 SMG
C810 87-010-831-080 C-CAP,U 0.1-16F
C811 87-A12-089-080 CAP,E 3.3-50 SMG
C812 87-A12-089-080 CAP,E 3.3-50 SMG
C814 87-012-286-080 C-CAP,U 0.01-25
C815 87-A12-090-080 CAP,E 4.7-50 SMG
C816 87-A12-090-080 CAP,E 4.7-50 SMG
C821 87-A12-091-080 CAP,E 10-50 SMG
C823 87-010-986-080 C-CAP,S 820P-25 J CH
C824 87-A12-090-080 CAP,E 4.7-50 SMG
C825 87-A10-504-080 C-CAP,U 0.047-16 K B
C842 87-012-286-080 C-CAP, U 0.01-25 B
C843 87-012-286-080 C-CAP,U 0.01-25 K B
C845 87-012-286-080 C-CAP,U 0.01-25 K B
DESCRIPTIONREF. NO. KANRI
7
PART NO.
NO.
C846 87-012-286-080 C-CAP,U 0.01-25 K B
C849 87-012-286-080 C-CAP,U 0.01-25 K B
C844 87-012-286-080 C-CAP, U 0.01-25 B
C850 87-A12-071-080 CAP,E 47-25 SMG
C851 87-012-286-080 C-CAP, U 0.01-25 B
C852 87-012-286-080 C-CAP, U 0.01-25 B
C853 87-012-286-080 C-CAP, U 0.01-25 B
C858 87-010-831-080 C-CAP,U 0.1-16F
C901 87-018-145-080 CAP,TC-U 6.8P-50 CH
C904 87-012-286-080 C-CAP, U 0.01-25 B
C905 87-012-286-080 C-CAP, U 0.01-25 B
C907 87-012-286-080 C-CAP, U 0.01-25 B
C908 87-A10-915-080 C-CAP, U 1000P-25 J CH
C909 87-012-286-080 C-CAP, U 0.01-25 B
C910 87-012-174-080 C-CAP, U 12P-50 CH
C911 87-012-170-080 C-CAP, U 8P-50 D CH
C912 87-012-195-080 C-CAP, U 100P-50 J CH
C913 87-012-286-080 C-CAP,U 0.01-25 B
C914 87-012-166-080 C-CAP,U 4P-50 C CH
C915 87-012-174-080 C-CAP, U 12P-50 CH
C916 87-012-180-080 C-CAP, U 22P-50 CH
C917 87-012-186-080 C-CAP, U 39P-50 CH
C918 87-A10-039-080 C-CAP, U 470P-50 J CH
C921 87-012-195-080 C-CAP, U 100P-50 CH
C922 87-012-174-080 C-CAP, U 12P-50 CH
C940 87-012-286-080 C-CAP,U 0.01-25 K B
C941 87-012-180-080 C-CAP,U 22P-50 J CH
C943 87-012-286-080 C-CAP,U 0.01-25 K B
C945 87-012-286-080 C-CAP,U 0.01-25 K B
C946 87-010-971-080 C-CAP,S 4700P-50 J B
C947 87-012-286-080 C-CAP,U 0.01-25 K B
C948 87-012-166-080 C-CAP,U 4P-50 C CH
C952 87-012-286-080 C-CAP,U 0.01-25 K B
C953 87-012-286-080 C-CAP,U 0.01-25 K B
C954 87-A12-086-080 CAP,E 0.47-50 SMG
C956 87-A12-062-080 CAP,E 100-10 SMG
C959 87-010-831-080 C-CAP,U 0.1-16F
C962 87-A12-087-080 CAP,E 1-50 SMG
C963 87-015-785-080 C-CAP,0.1-25 Z F C3216
C964 87-010-175-080 C-CAP,S 560P-50 J SL
C971 87-A12-067-080 CAP,E 330-16 SMG
C972 87-A12-090-080 CAP,E 4.7-50 SMG
C973 87-012-286-080 C-CAP,U 0.01-25
C974 87-012-286-080 C-CAP,U 0.01-25
C979 87-012-195-080 C-CAP,U 100P-50CH
C981 87-A12-071-080 CAP,E 47-25 SMG
C982 87-010-831-080 C-CAP,U 0.1-16F
C983 87-012-286-080 C-CAP,U 0.01-25
C984 87-012-286-080 C-CAP,U 0.01-25
C987 87-012-286-080 C-CAP,U 0.01-25
C989 87-012-286-080 C-CAP,U 0.01-25 K B
C991 87-012-176-080 C-CAP,U 15P-50 CH
C992 87-012-176-080 C-CAP,U 15P-50 CH
C993 87-012-274-080 C-CAP,U 1000P-50B
C995 87-012-274-080 C-CAP,U 1000P-50B
C997 87-010-831-080 C-CAP,U 0.1-16F
C998 87-A12-071-080 CAP,E 47-25 SMG
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER,CF SFE10.7MA5-A
CF832 87-008-261-010 FILTER,CF SFE10.7MA5-A
CN11 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3
CN12 87-A61-108-010 CONN,5P V TID-A
CN131 87-A60-619-010 CONN,2P V 2MM JMT
CN132 87-A60-619-010 CONN,2P V 2MM JMT
CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-099-194-010 CONN,6P V BLK 6216
CN604 87-099-749-010 CONN,9P V 9604SC
CN607 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
CNA11 8A-NF8-653-010 CONN ASSY,9P TID-A(480)
CNA12 8B-NF6-661-010 CONN ASSY,3P V PANO(150)
CNA101 8B-NF6-660-010 CONN ASSY,2P V PANO(250)
D902 87-A40-128-080 C-VARI-CAP,HVA202A
D903 87-A40-128-080 C-VARI-CAP,HVA202A
D951 87-A40-618-080 VARI-CAP,SVC 348(S/T)
FB101 87-008-474-080 F-BEAD,BL02RN1-R62T2 EMI
FB102 87-008-474-080 F-BEAD,BL02RN1-R62T2 EMI
FB501 87-008-372-080 FILTER, EMI BL 01 RN1
FB601 87-008-372-080 FLTR,EMI BL01 RN1
FFC602 88-906-481-110 FF-CABLE,6P 1.25 480MM
FFC604 88-909-141-110 FF-CABLE,9P 1.25 140MM
J101 87-A60-929-010 JACK,DIA6.3 BLK ST W/S TAI
J102 87-A60-238-010 TERMINAL,SP 4P (MSC)
J105 87-A61-487-010 JACK,PIN 4P RBWB TC58 118-06
J601 87-A60-885-010 JACK,PIN 6P R/W MSC
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02
J940 87-A60-633-010 CONN,2P H 2.5MM JMT
JR646 87-A50-322-080 C-COIL,S BK2125 LM252
JW13 87-A01-001-050 RES,220-1/2W J BLT2J
JW603 87-008-372-080 FLTR,EMI BL01 RN1
JW640 87-008-372-080 FLTR,EMI BL01 RN1
JW653 87-008-372-080 FLTR,EMI BL01 RN1
JW691 87-008-372-080 FLTR,EMI BL01 RN1
L101 87-A50-610-010 COIL,1UH K(MDEC)
L102 87-A50-610-010 COIL,1UH K(MDEC)
L121 87-A50-610-010 COIL,1UH K(MDEC)
L122 87-A50-610-010 COIL,1UH K(MDEC)
L301 87-A50-625-010 COIL,TRAP 85KHZ (SANWA)
L302 87-A50-625-010 COIL,TRAP 85KHZ (SANWA)
L351 87-007-342-010 COIL,OSC 85KHZ BIAS
L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-552-010 FLTR,CFMT-450AL(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)
L832 87-005-847-080 COIL,2.2UH(CECS)
L902 88-ZA1-602-110 COIL,FM-RF-U2 2G
L903 88-ZA1-601-010 COIL,FM-RF-U1 2G
L904 87-005-847-080 COIL,2.2UH(CECS)
L905 88-ZA1-624-010 COIL,FM IFT 7-6.2(COILS)
L906 88-ZA1-603-010 COIL,FM-OSC-U 2G
L941 87-A50-022-010 COIL,ANT SW(COI)7.96MHZ
L942 87-A50-550-010 COIL,OSC SW-2N(COI)
L943 87-A50-522-080 COIL,1MH K CEC
L944 87-A50-159-010 COIL,10MH K C2B
L952 87-A50-430-010 COIL,ANT MW(3BSW)
L953 87-A50-431-010 COIL,OSC MW(3BSW)
R681 87-012-280-080 C-CAP,U 3300P-50 K B
R682 87-012-280-080 C-CAP,U 3300P-50 K B
R790 87-012-286-080 C-CAP,U 0.01-25 B
R991 87-012-195-080 C-CAP,U 100P-50CH
R993 87-012-195-080 C-CAP,U 100P-50CH
R995 87-012-195-080 C-CAP,U 100P-50CH
SFR351 87-024-436-080 SFR,47K H RH063MC
SFR352 87-024-436-080 SFR,47K H RH063MC
TC941 87-A91-773-080 TRIMMER,PLY 20P 6.8x5.4 CDYL
TC943 87-A91-774-080 TRIMMER,PLY 30P 6.8x5.4 CDYL
WH11 87-A91-179-010 HLDR,WIRE 2.5-11P
X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST
FRONT C.B
C113 87-010-788-080 C-CAP,U 0.33-25 Z F
C201 87-016-083-080 C-CAP,S 0.15-16 K R
C202 87-012-270-080 CAP,U 470P-50 K B
C203 87-A12-319-080 C-CAP,U 0.1-50 Z F
C207 87-010-590-080 C-CAP,S 0.015-16 K R
C301 87-012-172-080 C-CAP,U 10P-50 D CH
C302 87-012-172-080 C-CAP,U 10P-50 D CH
C303 87-012-172-080 C-CAP,U 10P-50 D CH
C304 87-012-172-080 C-CAP,U 10P-50 D CH
DESCRIPTIONREF. NO. KANRI
8
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
C305 87-012-172-080 C-CAP,U 10P-50 D CH
C307 87-A12-317-080 C-CAP,U 0.1-50 Z F
C308 87-A12-317-080 C-CAP,U 0.1-50 Z F
C309 87-A12-317-080 C-CAP,U 0.1-50 Z F
C351 87-010-787-080 C-CAP,U 0.022-25 K B
C352 87-010-787-080 C-CAP,U 0.022-25 K B
C355 87-010-787-080 C-CAP,U 0.022-25 K B
C383 87-010-759-080 C-CAP,U 0.1-25 Z F
C384 87-010-759-080 C-CAP,U 0.1-25 Z F
C385 87-010-759-080 C-CAP,U 0.1-25 Z F
C386 87-010-759-080 C-CAP,U 0.1-25 Z F
C387 87-010-759-080 C-CAP,U 0.1-25 Z F
C601 87-012-282-080 CAP,U 4700P-50 K B
C602 87-010-405-040 CAP,E 10-50 M 11L SME
C605 87-A12-317-080 C-CAP,U 0.1-50 Z F
C606 87-010-112-040 CAP,E 100-16 M 11L SME
C607 87-010-759-080 C-CAP,U 0.1-25 Z F
C611 87-012-274-080 C-CAP,U 1000P-50 K B
C612 87-010-492-040 CAP,E 0.33-50 M 5L SRE
C613 87-012-191-080 C-CAP,U 68P-50 J CH
C614 87-012-274-080 C-CAP,U 1000P-50 K B
C652 87-012-279-080 C-CAP,U 2700P-50 K B GRM
C653 87-010-785-080 C-CAP,U 0.015-25 K B GRM
C701 87-010-406-040 CAP,E 22-50 M 11L SME
C901 87-010-759-080 C-CAP,U 0.1-25 Z F
C902 87-012-145-080 C-CAP,S 270P-50 J CH GRM
C903 87-012-195-080 C-CAP,U 100P-50 J CH
C904 87-010-596-080 C-CAP,S 0.047-16 K R C2012
C905 87-012-176-080 C-CAP,U 15P-50 J CH
C906 87-A10-189-040 CAP,E 220-10 M 5L
C908 87-012-274-080 C-CAP,U 1000P-50 K B
C909 87-012-286-080 C-CAP,U 0.01-25 K B
C910 87-012-270-080 C-CAP,U 470P-50 K B
C911 87-012-199-080 C-CAP,U 220P-50 J CH
C912 87-012-199-080 C-CAP,U 220P-50 J CH
C913 87-012-199-080 C-CAP,U 220P-50 J CH
C914 87-012-199-080 C-CAP,U 220P-50 J CH
C915 87-012-199-080 C-CAP,U 220P-50 J CH
C916 87-012-199-080 C-CAP,U 220P-50 J CH
C917 87-012-199-080 C-CAP,U 220P-50 J CH
C918 87-012-199-080 C-CAP,U 220P-50 J CH
C919 87-012-199-080 C-CAP,U 220P-50 J CH
C920 87-012-199-080 C-CAP,U 220P-50 J CH
C921 87-012-270-080 C-CAP,U 470P-50 K B
C923 87-010-759-080 C-CAP,U 0.1-25 Z F
C925 87-A12-317-080 C-CAP,U 0.1-50 Z F
C926 87-010-759-080 C-CAP,U 0.1-25 Z F
C927 87-010-759-080 C-CAP,U 0.1-25 Z F
C928 87-010-408-040 CAP,E 47-50 M 11L SME
C929 87-012-369-080 C-CAP,S 0.047-50 Z F
C931 87-010-404-040 CAP,E 4.7-50 M 11L SME
C933 87-010-404-040 CAP,E 4.7-50 M 11L SME
C991 87-010-405-040 CAP,E 10-50 M 11L SME
C992 87-012-157-080 C-CAP,S 330P-50 J CH GRM
CN101 87-099-720-010 CONN,30P BLK TYK-B(P)
CN104 87-099-017-010 CONN,15P V BLK 6216
CN151 87-099-196-010 CONN,8P V BLK 6216
FB601 87-008-372-080 FLTR,EMI BL01 RN1
FFC104 88-915-181-110 FF-CABLE,15P 1.25 180MM
FFC151 88-908-301-110 FF-CABLE,8P 1.25
FL901 8B-NF7-621-010 FL,BJ815GNK
J601 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
J602 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
JW202 87-008-372-080 FLTR,EMI BL01 RN1
JW205 87-008-372-080 FLTR,EMI BL01 RN1
JW547 87-008-474-080 F-BEAD,BL02RN1-R62T2 EMI
JW954 87-008-372-080 FLTR,EMI BL01 RN1
L901 87-A50-657-010 COIL,CLK 9.43MHZ (TOKO)7KLY
LED201 87-A40-317-080 LED,SLR-342VCT31 RED
LED401 87-A41-119-040 LED,SLR-56DCT31 ORN
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
LED402 87-A41-119-040 LED,SLR-56DCT31 ORN
LED403 87-A41-119-040 LED,SLR-56DCT31 ORN
LED404 87-A41-119-040 LED,SLR-56DCT31 ORN
LED405 87-A41-119-040 LED,SLR-56DCT31 ORN
R358 87-010-787-080 C-CAP,U 0.022-25 K B
R359 87-010-787-080 C-CAP,U 0.022-25 K B
S301 87-A90-164-080 SW,TACT SKQNAB(N)
S302 87-A90-164-080 SW,TACT SKQNAB(N)
S303 87-A90-164-080 SW,TACT SKQNAB(N)
S304 87-A90-164-080 SW,TACT SKQNAB(N)
S351 8B-NF6-218-010 HLDR,TS CRAMP
S352 8B-NF6-218-010 HLDR,TS CRAMP
S353 8B-NF6-218-010 HLDR,TS CRAMP
S354 8B-NF6-218-010 HLDR,TS CRAMP
S355 8B-NF6-218-010 HLDR,TS CRAMP
S356 8B-NF6-218-010 HLDR,TS CRAMP
S357 8B-NF6-218-010 HLDR,TS CRAMP
S358 8B-NF6-218-010 HLDR,TS CRAMP
KEY C.B
C502 87-A12-317-080 C-CAP,U 0.1-50 Z F
C531 87-012-172-080 C-CAP,U 10P-50 D CH
C532 87-012-172-080 C-CAP,U 10P-50 D CH
C533 87-012-172-080 C-CAP,U 10P-50 D CH
C534 87-012-172-080 C-CAP,U 10P-50 D CH
C535 87-012-172-080 C-CAP,U 10P-50 D CH
C536 87-012-172-080 C-CAP,U 10P-50 D CH
C537 87-012-172-080 C-CAP,U 10P-50 D CH
C571 87-012-286-080 C-CAP,U 0.01-25 K B
C572 87-012-286-080 C-CAP,U 0.01-25 K B
C573 87-012-286-080 C-CAP,U 0.01-25 K B
C574 87-012-286-080 C-CAP,U 0.01-25 K B
C575 87-012-286-080 C-CAP,U 0.01-25 K B
C576 87-012-286-080 C-CAP,U 0.01-25 K B
C577 87-012-286-080 C-CAP,U 0.01-25 K B
C581 87-012-274-080 C-CAP,U 1000P-50 K B
C582 87-012-195-080 C-CAP,U 100P-50 J CH
C583 87-012-195-080 C-CAP,U 100P-50 J CH
C591 87-012-274-080 C-CAP,U 1000P-50 K B
C592 87-012-195-080 C-CAP,U 100P-50 J CH
C593 87-012-195-080 C-CAP,U 100P-50 J CH
CN501 8B-NF6-606-010 CONN ASSY,6P DADA
CN502 8B-NF6-607-010 CONN ASSY,7P DADA
CN503 8B-NF6-606-010 CONN ASSY,6P DADA
LED501 87-A40-496-040 LED,SLR-342PCT31 GRN
LED502 87-A40-496-040 LED,SLR-342PCT31 GRN
LED503 87-A40-496-040 LED,SLR-342PCT31 GRN
LED511 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED512 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED513 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED514 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED515 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED516 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED517 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED518 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED521 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED522 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED523 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED524 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED525 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED526 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED527 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED528 87-A40-619-040 LED,SLR-56PT-T31-W GRN
S531 87-A90-164-080 SW,TACT SKQNAB(N)
S532 87-A90-164-080 SW,TACT SKQNAB(N)
S533 87-A90-164-080 SW,TACT SKQNAB(N)
S534 87-A90-164-080 SW,TACT SKQNAB(N)
S535 87-A90-164-080 SW,TACT SKQNAB(N)
S536 87-A90-164-080 SW,TACT SKQNAB(N)
9
PART NO. DESCRIPTIONREF. NO. KANRI
DESCRIPTIONREF. NO. KANRI
NO.
S537 87-A90-164-080 SW,TACT SKQNAB(N)
S538 87-A90-164-080 SW,TACT SKQNAB(N)
S539 87-A90-164-080 SW,TACT SKQNAB(N)
S540 87-A90-164-080 SW,TACT SKQNAB(N)
S541 87-A90-164-080 SW,TACT SKQNAB(N)
S542 87-A90-164-080 SW,TACT SKQNAB(N)
S543 87-A90-164-080 SW,TACT SKQNAB(N)
S544 87-A90-164-080 SW,TACT SKQNAB(N)
S545 87-A90-164-080 SW,TACT SKQNAB(N)
S546 87-A90-164-080 SW,TACT SKQNAB(N)
S547 87-A90-164-080 SW,TACT SKQNAB(N)
S548 87-A90-164-080 SW,TACT SKQNAB(N)
S549 87-A90-164-080 SW,TACT SKQNAB(N)
S550 87-A90-164-080 SW,TACT SKQNAB(N)
S551 87-A90-164-080 SW,TACT SKQNAB(N)
S571 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S572 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S573 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S574 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S575 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S576 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S577 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S578 8B-NF6-219-010 HLDR,TS CRAMP SLNT
S581 87-A92-114-010 SW,RTRY EC12E24504 30MM
S591 87-A92-113-010 SW,RTRY EC12E12504 30MM
AMP 3M C.B
C1 87-010-759-080 C-CAP,U 0.1-25 Z F
C2 87-010-759-080 C-CAP,U 0.1-25 Z F
C3 87-010-759-080 C-CAP,U 0.1-25 Z F
C4 87-010-759-080 C-CAP,U 0.1-25 Z F
C15 87-010-759-080 C-CAP,U 0.1-25 Z F
C17 87-016-299-080 CAP,E 10-100 M SME
C18 87-010-866-080 CAP,E 10-63 M VX
C101 87-012-276-080 C-CAP,U 1500P-50 K B
C102 87-012-276-080 C-CAP,U 1500P-50 K B
C103 87-A12-085-080 CAP,E 0.33-50 SMG
C104 87-A12-085-080 CAP,E 0.33-50 SMG
C105 87-012-278-080 C-CAP,U 2200P-50 K B
C106 87-012-278-080 C-CAP,U 2200P-50 K B
C107 87-A12-090-080 CAP,E 4.7-50 SMG
C108 87-A12-090-080 CAP,E 4.7-50 SMG
C111 87-A12-077-080 CAP,E 33-35 SMG
C112 87-A12-077-080 CAP,E 33-35 SMG
C115 87-010-177-080 C-CAP,S 820P-50 J SL C2012
C116 87-010-177-080 C-CAP,S 820P-50 J SL C2012
C117 87-A10-596-080 C-CAP,S 100P-100 J CH
C118 87-A10-596-080 C-CAP,S 100P-100 J CH
C119 87-012-368-080 C-CAP,S 0.1-50 Z F
C120 87-012-368-080 C-CAP,S 0.1-50 Z F
C121 87-A10-596-080 C-CAP,S 100P-100 J CH
C122 87-A10-596-080 C-CAP,S 100P-100 J CH
C141 87-012-282-080 C-CAP,U 4700P-50 K B
C142 87-012-278-080 C-CAP,U 2200P-50 K B
C151 87-012-286-080 C-CAP,U 0.01-25 K B
C152 87-012-286-080 C-CAP,U 0.01-25 K B
C161 87-010-759-080 C-CAP,U 0.1-25 Z F
CN1 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3
CN102 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3
CNA1 8B-NF6-645-010 CONN ASSY,5P TID-A(110)
R171 87-A00-418-010 RES,M/F 0.15-3W J
R172 87-A00-418-010 RES,M/F 0.15-3W J
R173 87-A00-418-010 RES,M/F 0.15-3W J
R174 87-A00-418-010 RES,M/F 0.15-3W J
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001
WH1 87-A90-459-010 HLDR,WIRE 2.5-5P
PART NO.
NO.
C201 87-A12-088-080 CAP,E 2.2-50 SMG
C202 87-A12-088-080 CAP,E 2.2-50 SMG
C203 87-A12-062-080 CAP,E 100-10 SMG
C204 87-A12-062-080 CAP,E 100-10 SMG
C207 87-012-286-080 C-CAP,U 0.01-25 K B
C208 87-012-286-080 C-CAP,U 0.01-25 K B
C213 87-012-172-080 C-CAP,U 10P-50 D CH
C215 87-010-831-080 C-CAP,U 0.1-16 Z F
C216 87-010-831-080 C-CAP,U 0.1-16 Z F
C301 87-012-280-080 CAP,U 3300P-50 K B
C302 87-012-280-080 CAP,U 3300P-50 K B
C303 87-A12-084-080 CAP,E 0.22-50 SMG
C304 87-A12-084-080 CAP,E 0.22-50 SMG
C309 87-A12-089-080 CAP,E 3.3-50 SMG
C310 87-A12-089-080 CAP,E 3.3-50 SMG
C311 87-A12-092-080 CAP,E 22-50 SMG
C312 87-A12-092-080 CAP,E 22-50 SMG
C315 87-012-199-080 C-CAP,U 220P-50 J CH
C316 87-012-199-080 C-CAP,U 220P-50 J CH
C317 87-012-286-080 C-CAP,U 0.01-25 K B
C318 87-012-286-080 C-CAP,U 0.01-25 K B
C401 87-010-831-080 C-CAP,U 0.1-16 Z F
C402 87-010-831-080 C-CAP,U 0.1-16 Z F
C403 87-A12-091-080 CAP,E 10-50 SMG
C404 87-A12-091-080 CAP,E 10-50 SMG
C501 87-012-282-080 C-CAP,U 4700P-50 K B
C502 87-012-278-080 C-CAP,U 2200P-50 K B
CN101 87-099-197-010 CONN,9P V BLK 6216
CN102 87-099-043-010 CONN,2P V WHT EH
CN104 87-049-919-010 CONN,3P V WHT EH
R333 87-A00-258-080 RES,M/F 0.22-1W J
R334 87-A00-258-080 RES,M/F 0.22-1W J
PT C.B
CN1 87-A61-110-010 CONN,9P V TID-A
PT1 8B-NH6-611-010 PT,BNH-6 HR
!
PT3 8B-MA6-673-010 PT,SUB BMA H (VRK)
!
RY1 87-A91-339-010 RELAY,AC DC12V G5PA-2
!
S1 87-A90-165-010 SW,SL 1-2-3 SWS2301
!
T1 87-A60-317-010 TERMINAL,1P MSC
!
T2 87-A60-317-010 TERMINAL,1P MSC
!
DECK C.B
CON502 87-099-756-010 CONN,15P H 9604
SFR1 87-024-581-010 SFR,3.3K H KVSF637A
SOL1 82-ZM3-627-010 SOL ASSY,27 SO
SOL2 82-ZM3-627-010 SOL ASSY,27 SO
SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW4 87-036-110-010 SW,MICRO SPPB62
SW5 87-036-110-010 SW,MICRO SPPB62
SW6 87-036-110-010 SW,MICRO SPPB62
SW8 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW9 87-A90-248-010 SW,MICRO ESE11SH2CXQ
HEAD-1 C.B
CON301 87-NF6-615-010 CONN ASSY,3P PB
HEAD-2 C.B
CON351 87-NF6-616-010 CONN ASSY,8P RPB
PANORAMA AMP C.B
10
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
11
TRANSISTOR ILLUSTRATION
E C B E C B B C E
KTA1266GR
KTC3198GR
CC5551
2SA1980G
2SA1981Y
G
E C B
2SA1585SR
E C B
2SA933AS(R)
2SC4115SRS
G
C
2SB1342
2SB1370E
2SB1588
2SD1933
2SD2439
D
S
2SK2158
G D S
2SK3053
S
D
G
2SK360E
S
D
2SJ106GR
B
E
2SA1235F
2SB792A(RS)
2SC2714O
2SC3052F
2SC5345SF/S(O)
2SD814A(RS)
CSD1306E
KRA102S
KRA104S
KRA107S
KRC102S-RTK
RT1N 144C
RT1P 141C
12
WIRING 1 (MAIN)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
13
R
S
T
U
SCHEMATIC DIAGRAM – 1 (MAIN : 1 / 6 <FUNCTION SECTION>)
– 14 –
SCHEMATIC DIAGRAM – 2 (MAIN : 2 / 6 <P–SUPPLY SECTION>)
– 15 –
SCHEMATIC DIAGRAM – 3 (MAIN : 3 / 6 <AMP SECTION>)
– 16 –
SCHEMATIC DIAGRAM – 4 (MAIN : 4 / 6 <DECK SECTION> / HEAD – 1 / HEAD – 2)
– 17 –
SCHEMATIC DIAGRAM – 5 (MAIN : 5 / 6 <DSP SECTION>)
– 18 –
SCHEMATIC DIAGRAM – 6 (MAIN : 6 / 6 <TUNER SECTION>)
– 19 –
WIRING 2 (FRONT)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
20
R
S
T
U
WIRING 3 (KEY)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
21
R
S
T
U
SCHEMATIC DIAGRAM – 7 (FRONT / KEY / DECK)
– 22 –
WIRING – 4 (AMP 3M)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 23 –
R
S
T
U
SCHEMATIC DIAGRAM – 8 (AMP 3M)
– 24 –
WIRING – 5 (PANORAMA AMP)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 25 –
R
S
T
U
SCHEMATIC DIAGRAM – 9 (PANORAMA AMP)
– 26 –
WIRING 6 (PT)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
27
R
S
T
U
SCHEMATIC DIAGRAM – 10 (PT)
– 28 –
WIRING 7 (DECK / HEAD 1 / HEAD 2)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
29
R
S
T
U
FL (BJ815GNK) GRID ASSIGNMENT / PIN CONNECTION / ANODE CONNECTION
GRID ASSIGNMENT
PIN CONNECTION
30
ANODE CONNECTION
NOTE:
= (UP)
= (DOWN)
31
IC B L O C K DIAGRAM
32
33
IC DESCRIPTION
IC, LC876670B–5Y60
Pin No. Pin Name I/O Description
1 O–S_CLK I VCD SR control.
2 O–S_DATA O VCD SR data output.
3 O–MOTOR O Tape motor ON/OFF.
4 O–SOL1 O Tape 1 plunger ON/OFF.
5 O–SOL2 O Tape 2 plunger ON/OFF.
6 O–RSM–CE O Rhythm IC chip enable output. (Not used)
7 O–HSP O PLL-IC chip enable output.
8 O–PANORAMA O Panoramic IC data output.
9 O–MUTE O Mute output. Mute ON/OFF.
10 O–CLK_SFT O System microcomputer clock shift ON/OFF output.
11 RESET — System reset.
12 I–DISH I CD turn-table position detection AD input.
13 I–SPEANA / I–MS I Spectrum analyzer level / MS input. AD input.
14 VSS1 — Connected to GND.
15 CF1 I Oscillator circuit input.
16 CF2 O Oscillator circuit output.
17 VDD1 — Connected to power supply.
18 I–HOLD I System power observation AD input.
19 I–KEY1 I KEY 1 AD input.
20 I–KEY2 I KEY 2 AD input.
21 I–KEY3 I KEY 3 AD input.
22 I–CDSW I CD mechanical switch AD input.
23 I–RT_VR I VOLUME rotary encoder AD input.
24 I–RT_JOG I JOG rotary encoder AD input.
25 I–MIC I Auto VF microphone input. Small signal detection (MIC IN) input.
26 I–TM–BASE I Time base input.
27 I–CD_ACK I VCD ACK input.
28 O–POWER O System power ON/OFF output.
29 I-RMC I Remote-control signal reception input. Active at “L”.
30~41 G12~G1 O FL grid G12~G1 output.
42~45 P35~P32 O FL segment P35~P32 output.
46 VDD3 — Connected to power supply.
47 SPEANA–A / P31 O Spectrum analyzer band switching output A / FL segment P31 output.
48 SPEANA–B / P30 O Spectrum analyzer band switching output B / FL segment P30 output.
49 SPEANA–C / P29 O Spectrum analyzer band switching output C / FL segment P29 output.
50 I–HPMUTE / P28 I/O Headphone MUTE input / FL segment P28 output.
51 –VP — Power supply for FL display.
52 I–STEREO / P27 I/O Tuner stereo detect input / FL segment P27 output.
53~56 P26~P23 O FL segment P26~P23 output.
57 BEAT–M / P22 I/O Beat master diode input (not used) / FL segment P22 output.
58 KCON / P21 I/O KCON enable diode input (not used) / FL segment P21 output.
59 DSP / P20 I/O DSP enable diode input / FL segment P20 output.
– 34 –
Pin No. Pin Name I/O Description
60 DOLBY / P19 I/O DOLBY enable diode input (not used) / FL segment P19 output.
61 CASINO / P18 I/O Casino DEMO diode input / FL segment P18 output.
62 KARAOKE / P17 I/O Karaoke enable diode input (not used) / FL segment P17 output.
63 PANORAMA / P16 I/O Panorama enable diode input (not used) / FL segment P16 output.
64 DEMO / P15 I/O Demonstration OFF diode input (not used) / FL segment P15 output.
65 ECO / P14 I/O Initial echo OFF diode input / FL segment P14 output.
66 OIRT / P13 I/O OIRT diode input (not used) / FL segment P13 output.
67 SW / P12 I/O SW diode input / FL segment P12 output.
68 LW / P11 I/O LW diode input (not used) / FL segment P11 output.
69 AMST / P10 I/O AMST diode input (not used) / FL segment P10 output.
70 AM10K / P9 I/O AM10K diode input (not used) / FL segment P9 output.
71 CST2 / P8 I/O CST2 diode input / FL segment P8 output.
72 VDD4 — Connected to power supply.
73 REB / P7 I/O REB diode input / FL segment P7 output.
74 CAM2 / P6 I/O CAM2 diode input / FL segment P6 output.
75 AUTO1 / P5 I/O AUTO1 diode input / FL segment P5 output.
76 AUTO2 / P4 I/O AUTO2 diode input / FL segment P4 output.
77 CAM1 / P3 I/O CAM1 diode input / FL segment P3 output.
78 CST1 / P2 I/O CST1 diode input / FL segment P2 output.
79 REA / P1 I/O REA diode input / FL segment P1 output.
80 O–CD_DA TA O VCD data output.
81 I–IFC I TUNER IFC input.
82 I–CD–DATA I VCD data input.
83 O–LED_JOG O JOG flash ring LED indicator ON/OFF.
84 O–LED_VOL O VOL flash ring LED indicator ON/OFF.
85 O–LED_TUNER O TUNER function LED ON/OFF.
86 O–LED_MD O MD function LED ON/OFF.
87 O–LED_AUX O AUX function LED ON/OFF.
88 O–LED_TAPE O TAPE function LED ON/OFF.
89 VSS2 — Connected to GND.
90 VDD2 — Connected to power supply.
91 O–LED_CD O CD function LED ON/OFF.
92 O–LED_CD1 O CD1 direct button LED ON/OFF.
93 O–LED_CD2 O CD2 direct button LED ON/OFF.
94 O–LED_CD3 O CD3 direct button LED ON/OFF.
95 O–KSCAN O “L” at key-scan timing switching retrieve.
96 O–PLL–CE O PLL-IC chip enable output.
97 O–M_STB O Main C.B strobe output.
98 O–M_CLK O Main C.B clock output.
99 O–M_DATA O Main C.B data output.
100 O–CD_CLK O CD clock output.
– 35 –
ADJUSTMENT <TUNER / FRONT / DECK>
< TUNER SECTION >
1. Clock Frequency Check
Settings : Test point : TP2 (CLK)
Method : Set to MW 1602 kHz and check that the test point is 2052
kHz ± 45 Hz.
2. MW VT Adjustment
Settings : Test point : TP1 (VT)
Adjustment location : L953
Method : Set to MW 1602 kHz and adjust L953 so that the test
point becomes 8.5 V ± 0.05 V. Then set to MW 531 kHz
and check that the test point is more than 0.3 V.
3. MW Tracking Adjustment
Settings : Test point : TP8 (Lch), TP9 (Rch)
Adjustment location :
L952 ................................................... 603 kHz
TC941 ............................................... 1404 kHz
Method : Set up TC941 to center before adjustment.
The level at 603 kHz is adjusted to maximum by
L952. Then the level at 1404 kHz is adjust to maximum
by TC941.
4. SW VT Adjustment
Settings : Test point : TP1 (VT)
Adjustment location : L942
Method : Set to SW 17.9 MHz and adjust L942 so that the test
point becomes 8.0 V ± 0.05 V. Then set to SW 5.73 MHz
and check that the test point is more than 0.3 V.
5. SW Tracking Adjustment
Settings : Test point : TP8 (Lch), TP9 (Rch)
Adjustment location :
L941 ................................................. 5.73 MHz
TC943 ...............................................17.9 MHz
Method : Set up TC943 to center before adjustment.
The level at 5.73 MHz is adjust to maximum by L941.
Then the level at 17.9 MHz is adjust to maximum by
TC943.
6. FM VT Adjustment
Settings : Test point : TP1 (VT)
Adjustment location : L906
Method : Set to FM 108.0 MHz and adjust L906 so that the test
point becomes 7.0 V ± 0.1 V. Then set to FM 87.5 MHz
and check that the test point is more than 0.4 V.
7. FM Tracking Adjustment
Settings : Test point : TP8 (Lch), TP9 (Rch)
Adjustment location: L903
Method : Set to FM 87.5 MHz and adjust L903 so that the
test point is less than 9 dBµV.
8. AM IF Adjustment
Settings : Test point : TP8 (Lch), TP9 (Rch)
Adjustment location :
L802 ................................................... 450 kHz
9. DC Balance / Mono Distortion Adjustment
Settings : Test point : TP3, TP4 (DC Balance)
TP8 (LCH), TP9 (RCH)
(MONO DISTORTION)
Adjustment location : L801
Input level : 60 dBµV
Method : Set to FM 98.0 MHz and adjust L801 so that the
distortion is minimun. Next, check that the voltage
between TP3 and TP4 is 0 V ± 500 mV.
10. Output Level Check
<AM>
Settings : Test point : TP8 (Lch), TP9 (Rch)
Input level : 74 dBµV
Method : Set to AM 999 kHz and check that the test point is
105 mV ± 3dB.
<FM>
Settings : Test point : TP8 (Lch), TP9 (Rch)
Input level : 60 dBµV
Method : Set to FM 98.0 MHz and check that the test point is
420 mV ± 3 dB.
11. FM Separation Check
Settings : Test point : TP8 (Lch), TP9 (Rch)
Input level : 60 dBµV
Method : Set to FM 98.0 MHz and check that the test point is
more than 25 dB.
< FRONT SECTION >
12. µ-CON OSC Adjustment
Settings : Test point : TP10 (K-SCAN)
TP11(GND)
Adjustment location : L901
Method : Insert AC plug while pressing of "POWER" key and
"CLOCK" function key.
Connect a frequency counter across TP10 and TP11.
Then adjust L901 so that the frequency across the test
point is 226.74 Hz ± 0.22 Hz (4.406 msec ~ 4.414 msec).
36
< DECK SECTION >
13. Tape Speed Adjustment (DECK 2)
Settings : Test tape : TTA100
Test point : TP6 (Lch),
TP7 (Rch)
Adjustment location : SFR
Method : Play back the test tape and adjust SFR
on the motor so that the test point becomes
3000 Hz ± 5 Hz (FWD) and
FWD SPEED ± 45 Hz (REV) with respect to
forward speed.
14. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : Test tape : TTA300
Test point : TP6 (Lch), TP7 (Rch)
Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 10 kHz signal of the test tape
and adjust screw so that the output becomes
maximum. Next, perform on REV PLAY mode.
15. PB Frequency Response Check (DECK 1, DECK 2)
Settings : Test tape : TTA330
Test point : TP6 (Lch), TP7 (Rch)
Method : Play back the 315 Hz and 8 kHz signals of the test
tape and check that the output ratio of the 8 kHz
signal with respect to that of the 315 Hz signal is
0 dB ± 3 dB.
17. REC/PB Frequency Response Adjustment
Settings : Test tape : TTA602 (Normal),
TTA615 (CrO2)
Test point : TP6 (Lch), TP7 (Rch)
Adjustment location : SFR351 (Lch), SFR352 (Rch)
Input signal : 10 kHz/1 kHz
(LINE IN) (-20 VU)
Method : Apply a 1 kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP6, TP7
becomes 21 mV. Record and play back
the 1 kHz and 10 kHz signal and adjust SFRs so that
the output of the 10 kHz signal is
+ 0.5 dB ± 0.5 dB (Normal) and 0 dB ± 2.5 dB (CrO2)
with respect to that of the 1 kHz signal.
18. REC/PB Sensitivity Check (DECK 2)
Settings : Test tape : TTA602 (Normal),
TTA615 (CrO2)
Test point : TP6 (Lch), TP7 (Rch)
Input signal : 1 kHz (0VU / 0 dB)
Method : Apply a 1 kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP6, TP7
becomes 210 mV. Record and play back
the 1 kHz signal and check that the output is
0 dB ± 2.5 dB (Normal) and 0 dB ± 3 dB (CrO2).
16. PB Sensitivity Check (DECK 1, DECK 2)
Settings : Test tape : TTA200
Test point : TP6 (Lch), TP7 (Rch)
Method : Play back the test tape and check that the output level
of the test point is 300 mV ± 30 mV.
37
CD TEST MODE
1. How to Start the CD Test Mode
While pressing the FUNCTION button, insert the AC plug to the power outlet.
When the test mode is started, the message [TEST] is displayed.
2. How to Exit the CD Test Mode
Press the POWER button, push other FUNCTION button or disconnect the AC plug.
3. Function Descriptions and Application of the CD Test Mode
No
1
2
3
4
5
6
Mode
Start mode
Search
mode
Play mode
Traverse
mode
Sled mode
Spindle
mode
Operation
STOP
button
Play button
PAUSE
button
FF button
RWD
button
REC/REC
MUTE
button
Display
All indicators light
READING
Normal
Normal
TEST
TEST
All indicators light
Function
All FL indicators light
LD illuminates all the time
Focus search continuous
operations *1
Spindle motor continuous kick
Normal playback
If TOC cannot be read, focus
search is continued
Tracking servo OFF/ON
Each time PAUSE button is
pressed, the tracking servo
repeats turning OFF/ON
Pickup moves to the inner
circumference *2
At the same time, lens kicks to
the inner circumference
Pickup moves to the outer
circumference *2
At the same time, lens kicks to
the outer circumference
The spindle motor rotates
forward (rough speed) by
pressing the button and
rotates backward by pressing
one more time and stops by
pressing again
Checking item
FL check
Microprocessor check
APC circuit check
Laser current measurement
Focus search waveform check
Focus error waveform check
(DRF in the search mode is
ignored)
Each servo circuit is checked
DRF check
Tracking balance check
Sled circuit check
Tracking circuit check
Mechanism operation check
Pickup check
Spindle circuit
Spindle motor
*1: The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer.
There can be a case that operations can not be performed correctly.
In such a case, turn off the main power. After cooling down the machine, restart the machine.
*2: Be careful not to damage the gear because the sled motor rotates while the FF or RWD button is being pressed even if the pick-
up is located in the innermost track or the outermost track.
38
MECHANICAL EXPLODED VIEW 1 / 1
48
A
PLATE,SHILD SIDE
BZG-5
A
f
A
50
41
40
18
E
A
G
19
17
16
15
14
I
10
13
8
7
5
3
W,4.21-6.5-
0.5 W/ADH
B
11
6
20
21
22
30
FL
23
24
26
25
I
a
F
10
33
27
28
32
29
31
58
57
56
42
f
A
62
PWB
63
A
M
C
A
SH,SHIELD
A
34
PWB
61
WIRE,
LUG
A
M
a
A
59
PWB
60
HT-SINK,FET
A
A
45
49
A
57
A
d
A
HT-SINK
e
d
J
J
e
43
PWB
A
52
A
46
J
BINDER
WIRE
47
HLDR,
PWB PT
A
PLATE,PT
A
63
BINDER
H
K
c
54
WIRE
K
H
K
b
53
A
44
51
J
49
A
c
A
A
1
W,4.21-6.5-0.5
W/ADH
35
36
12
9
7
2
4
D
PLATE,EARTH MECH
37
37
39
36
38
2ZM-3MK2
b
A
A
CHAS,MAIN
L
55
G
– 39 –
MECHANICAL PARTS LIST 1 / 1
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
1 8B-NF6-008-010 WINDOW,CASS1
2 8B-NF6-009-010 WINDOW,CASS2
3 8B-NF6-003-110 BOX,CASS1
4 8B-NF6-004-110 BOX,CASS2
5 8A-NF8-281-010 SPR-T,EJECT 1
6 8A-NF8-282-010 SPR-T,EJECT 2
7 8B-NF6-021-010 KNOB,RTRY VOL
8 8B-NF6-027-010 KEY,ASSY ENTER
9 8B-NF6-029-010 KEY,ASSY MIC
10 8Z-NF6-210-010 DMPR,150 N
11 8B-NH6-007-010 PANEL,OPE
12 8B-NH6-001-110 CABI,FR H
13 8B-NH6-003-010 WINDOW,DISP H
14 87-CE3-023-010 BADGE,AIWA 30N SILV
15 8B-NF6-010-010 PANEL,CD
16 8B-NF6-005-010 WINDOW,CD
17 8B-NF7-040-010 PANEL,TOP V-2 ANF8
18 8A-NF8-006-010 WINDOW,TOP
19 8B-NF6-034-010 PANEL,LEFT V-2
20 8B-NF6-012-110 KEY,POWER
21 8B-NF6-025-010 KEY,T-BASS
22 8B-NF6-017-010 KEY,CD
23 8B-NF6-024-010 REFLECTOR,CD
24 8B-NF6-022-010 REFLECTOR,FUN
25 8A-DB8-036-010 REFLECTOR,ECO
26 8B-NF6-211-010 GUIDE,FUN
27 8B-NF6-031-110 KEY,FUN
28 8B-NF6-032-010 KEY,OPE
29 8B-NF6-026-010 KEY,BBE
30 8B-NH6-002-010 KEY,VCD
31 8B-NF6-019-010 KEY,EDIT
32 8B-NF6-212-010 GUIDE,CD
33 8A-NF6-201-010 GUIDE,FL
34 8B-NF6-217-010 HLDR,PWB FR
35 87-NF4-216-010 HLDR,LOCK 1
36 86-NF9-224-010 SPR-C,LOCK
37 82-NF5-229-010 PLATE,LOCK
38 87-NF4-217-110 HLDR,LOCK 2
39 8B-NF6-213-010 PLATE,EARTH MIC
40 8B-NH6-005-010 WINDOW,TRAY
DESCRIPTIONREF. NO. KANRI
PART NO.
41 8B-NF6-002-010 PANEL,TRAY
42 8A-NF8-206-010 HLDR,PWB M
43 8B-NF6-206-010 HLDR,TR PNRM
44 8B-NF6-205-010 HLDR,TR AMP
45 8B-NF6-203-010 HLDR,HT-SINK F
46 8B-NF6-204-010 HLDR,HT-SINK R
47 87-A90-457-010 F-BEAD,15-25-15 E251
48 84-ZG1-245-210 CAP,OPTICAL
49 87-A91-751-010 FAN,DSB0812M-S382 -400MM
50 8B-NH6-004-010 CABI,REAR HRJSM
51 8B-NF7-238-010 HLDR,FAN LOW
52 87-NF4-221-010 HLDR,CABLE
!
53 87-A80-092-010 AC CORD ASSY,E BLK SUN FAI
54 87-085-185-010 BUSHING, AC CORD (E) CM-22B
55 8B-NF6-033-010 PANEL,RIGHT V-2
56 88-915-181-110 FF-CABLE,15P 1.25 180MM
57 87-A92-284-010 F-BEAD, E3407MFT2
58 88-908-301-110 FF-CABLE,8P 1.25
59 88-909-141-110 FF-CABLE,9P 1.25 140MM
60 88-906-481-110 FF-CABLE, 6P 1.25 480MM
61 87-NF6-616-010 CONN ASSY,8P RPB
62 87-NF6-615-010 CONN ASSY,3P PB
63 87-064-185-010 HLDR,WIRE PVC 0.5
A 87-067-703-010 TAPPING SCREW, BVT2+3-10
B 87-723-096-410 QT2+3-10W/O SLOT BL
C 87-721-096-410 QT2+3-10 GLD
D 87-067-688-010 BVTT+3-6
E 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
F 87-591-095-410 TAPPING SCREW, QIT+3-8 (GLD)
G 87-067-641-010 UTT2+3-8(W/O SLOT)BL
H 87-067-975-010 S-SCREW,IT+4-8
I 87-721-097-410 QT2+3-12 GLD
J 87-B10-315-010 BVIT3B+3-8 R W/O
K 87-078-200-010 S-SCREW,ITC+4-8 R
L 87-721-095-410 QT2+3-8GLD W/O SLOT
M 8B-NF6-220-010 W,3.5-8-0.5 W/ADH
NO.
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green HT Transparent Gray
HM Metallic Gray NH Champagne Gold M Wood Pattern
– 40 –
TAPE MECHANISM EXPLODED VIEW 1 / 1
50
A
48
51
49
47
44
B
C
46
52
53
a
54
A
9
B
47
48
49
50
29
60
31
38
35
29
58
a
37
32
29
30
39
51
43
40
43
37
39
35
36
7
27
38
32
31
58
b
PWB
8
1
2
3
PLATE
SHLD,M3
4
5
6
60
29
30
E
44
C
45
46
52
53
b
54
55
40
25
12
13
14
11
15
16
33
10
56
59
33
25
18
D
20
17
19
24
11
GEAR,
PLAY
21
57
23
PWB
7
8
28
19
42
26
15
13
14
16
17
18
20
4
GEAR,
PLAY
PLATE
SHLD,M3
D
5
6
21
19
28
23
41
24
42
22
PWB
55
34
– 41 –
TAPE MECHANISM PARTS LIST 1 / 1
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
1 82-ZM3-335-310 PULLEY,COUPLER M3
2 87-B10-043-010 W-P,0.99-4-0.25 SLT
3 86-ZM1-206-010 BELT,MAIN L
4 82-ZM1-322-010 SPR-T,FR 60
5 82-ZM1-220-210 GEAR,IDLER
6 82-ZM3-616-010 RING MAGNET 4
7 82-ZM3-348-010 LEVER ASSY,PINCH YL
8 82-ZM1-258-210 SPR-T,PINCH L
9 87-A91-195-110 HEAD,RPH KC9142 FPC
10 82-ZM3-342-010 BELT,SBU MOT 3
11 82-ZM1-338-110 BELT,FR 4
12 09-001-420-010 FLY-WHL,R ASSY
13 82-ZM3-333-310 SLIP DISK ASSY 2
14 82-ZM3-334-010 PW 2.16-6-0.4
15 82-ZM3-306-110 LVR,FR M2
16 82-ZM1-225-210 GEAR,FR
17 82-ZM3-305-310 GEAR,CAM M2(*)
18 82-ZM1-226-010 GEAR,REW
19 82-ZM1-216-510 GEAR,REEL
20 82-ZM1-227-310 LVR,TRIG
21 82-ZM1-265-310 SPR-E,TRIG
22 82-ZM3-351-010 HLDR,IC 2
23 82-ZM3-343-010 LEVER ASSY,PINCH YR
24 82-ZM1-259-210 SPR-T,PINCH R
25 82-ZM1-234-310 FLY-WHL,L ASSY
26 82-ZM1-237-610 FLY-WHL,R ASSY
27 82-ZM3-339-110 SHAFT,COUPLER N3
28 82-ZM1-255-310 SPR-E,LVR DIR
29 82-ZM1-217-410 REEL TABLE
30 82-ZM1-285-410 SPR-C,BT L
31 82-ZM1-333-210 PLATE,LINK2
32 82-ZM1-222-310 LVR,PLAY(*)
33 82-ZM3-307-010 CUSH-G,DIA3.7-8-3.2
34 87-045-347-010 MOT,SHU2L 70
35 82-ZM1-257-010 SPR-T,CAS
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
36 82-ZM3-340-010 SH,BELT D2
37 82-ZM1-242-010 LVR,CAS
38 82-ZM1-244-510 SPR-C,BT
39 82-ZM1-243-010 LVR,STOP
40 82-ZM1-240-110 LVR,REC(*)
41 82-ZM1-264-010 LVR,EJECT R
42 82-ZM3-627-010 SOL ASSY,27 SO
43 82-ZM1-241-310 LVR,MC
44 82-ZM1-208-310 HLDR,HEAD
45 87-A91-196-110 HEAD,PH KP9142 FPC
46 82-ZM1-314-110 PLATE,HEAD
47 82-ZM1-207-910 GUIDE,TAPE
48 82-ZM3-353-010 SPR-T,HEAD 2
49 82-ZM1-210-110 GEAR,H T
50 82-ZM1-219-110 SPR-T,LINK
51 82-ZM1-269-210 SPR-T,BRG
52 82-ZM1-218-010 SPR-E,HB
53 82-ZM1-206-910 CHAS,HEAD
54 82-ZM1-266-310 LVR,DIR
55 82-ZM1-214-010 SPR-T,DIR
56 82-ZM3-221-210 PULLEY,MOT 2M
57 82-ZM3-301-610 CHAS ASSY,M2
58 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT
59 82-ZM3-329-410 BELT,SBU R2
60 82-ZM1-288-010 SH,1.63-3.2-0.5 SLT
A 80-ZM6-207-010 V+1.6-7
B 86-ZM4-206-110 S-SCREW,AZIMUTH L
C 85-ZM3-202-010 S-SCREW,TG
D 82-ZM3-222-010 S-SCREW,SHILD PLATE
E 82-ZM3-318-110 S-SCREW W,MOTOR M2
– 42 –
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
12 3
How to Remove the PANEL, FR
1. Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 43 –
Fig-3
SPEAKER PARTS LIST (SX-WNSZ900) <YJ3SL>
PART NO.
NO.
1 8B-NS6-001-010 PANEL,FR A
2 8B-NS7-002-010 PANEL,SP A
3 8B-NS7-003-010 PANEL,SP B
4 8B-NS7-005-010 PANEL,BA A
5 8B-NS7-004-010 PANEL,DUCT
6 8B-NS8-007-010 PROTECTOR,M
7 8B-NS6-007-010 PROTECTOR,TW
8 8B-NS7-602-010 SPKR,W 200R 35/4
9 8B-NS7-604-010 SPKR,M 100W
10 88-NSK-610-010 SPKR,CERAMIC ASSY
11 88-NS5-610-010 CORD,SPKR
12 8B-NS7-009-010 PANEL,FR
13 8B-NS7-011-010 GRILLE,FRAME ASSY
14 8B-NS7-606-010 SPKR,80
15 8B-NS7-610-010 CORD,5.0
DESCRIPTIONREF. NO. KANRI
SPEAKER PARTS LIST (SX-S85) <YLSL>
PART NO.
NO.
1 8B-NS7-009-010 PANEL,FR
2 8B-NS7-011-010 GRILLE,FRAME ASSY
3 8B-NS7-606-010 SPKR,80
4 8B-NS7-610-010 CORD,5.0
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
1 8B-NH6-901-010 IB,H(ECA)M
2 8B-NH6-702-010 RC UNIT,RC-BAS08 VS
3 87-006-226-010 ANT,LOOP AM
4 87-043-115-010 FEEDER-ANT,FM
5 87-A90-119-010 ANT,WIRE SW(5M)
6 87-A80-167-010 CORD,PIN 1PY 150CM
7 87-A92-262-010 PLUG,CONVERSION WT 01011
!
NO.
DESCRIPTIONREF. NO. KANRI
– 44 –
2000075 921338
2-11, IKENOHATA 1-CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
Loading...