Page 1
NSX-VC8
HR
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
CD
CASSEIVER
NSX-VC8
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
NSX-VC8 (HR), (S/M Code No. 09-009-437-8T1).
CX–NVC8
BASIC TAPE MECHANISM : ZZM-2 PR1NM
BASIC CD MECHANISM : 3ZG-3 E8NM
SPEAKERSYSTEM
REMOTE
CONTROLLER
RC–AAS09SX-NVC8
S/M Code No. 09-00A-437-8R1
REVISION
DATA
Page 2
SPECIFICATIONS
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)
<AM tuner section>
Tuning range 531 kHz to 1602 kHz (9kHz step)
530 kHz to 1710 kHz (10 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<Amplifier section>
Power output Rated: 16 W + 16 W (6 ohms,
T.H.D. 1 %, 1 kHz)
Reference: 20 W + 20W (6 ohms,
T.H.D. 10 %, 1 kHz)
Total harmonic distortion 0.1 % (10 W, 1 kHz, 6 ohms, DIN
AUDIO)
Inputs VIDEO/AUX: 600 mV
MIC: 1 mV (10 kohms)
Outputs SPEAKERS: 6 ohms or more
PHONES: 32 ohms or more
VIDEO OUT: 1 Vp-p (75 ohms)
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 8000 Hz
Recording system AC bias
Heads Deck 1: recording/playback x 1,
erase x 1
Deck 2: playback x 1
<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
Video signal NTSC / PAL color format (selectable)
VIdeo data MPEG 1
Audio data MPEG 1, Layer 2
<Speaker system SX–NVC8>
Speaker system 1 way, bass reflex
Speaker units Full range: 100 mm cone
Impedance 6 ohms
Dimensions (W x H x D) 196 x 301 x 198 mm
Weight 1.8 kg
<General>
Power requirements 120 V / 220 - 230 V/ 240 V AC
(switchable), 50 Hz / 60 Hz
Power consumption 80 W
Dimensions (W x H x D) 260 x 302.5 x 266 mm
Weight 4.2 kg
• Specifications and external appearance are subject to change
without notice.
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP Assy PWB
Solder
– 3 –
Page 4
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
FRONT C.B
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
15
C113
Short with tweezers.
Fig-2-2
C113
%
*
VSS
VDD
MICROCOMPUTER
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
Page 6
ELECTRICAL MAIN PARTS LIST
PART NO.
NO.
IC
87-A21-381-040 C-IC,LA9235M
87-A21-557-010 C-IC,LC78635E
8Z-ZJP-602-010 C-IC,UPD78016FGC-574-AB8
87-017-760-080 IC,M51943BML
87-A20-925-040 C-IC,BA05FP
87-A20-905-040 C-IC,BA033FP
87-A21-513-040 C-IC,BA6998FP
87-A21-419-040 C-IC,NJM14558MD-TE2
87-A20-920-010 C-IC,CL680-D1
8A-NHC-602-010 C-IC,M38B57MCH-E260FP
87-070-083-010 IC,GP1U281X
87-A20-921-040 C-IC,SN74LVU04APW
87-A20-962-040 C-IC,MSM54V16258B/BSL
84-ZG1-695-040 C-IC,LH5V2RN1
87-A20-975-040 C-IC,SN74LV74APW
87-A21-443-040 C-IC,M62495AFP
87-A20-918-040 C-IC,SM5878AM
87-A20-974-040 C-IC,LC74781M-9017
87-A21-560-010 IC,LA1844L-A
87-070-127-110 IC,LC72131 D
TRANSISTOR
87-026-609-080 TR,KTA1266GR
87-A30-076-080 C-TR,2SC3052F
89-213-702-010 TR,2SB1370 (1.8W)
87-026-610-080 TR,KTC3198GR
87-A30-074-080 C-TR,RT1P 141C
87-A30-075-080 C-TR,2SA1235F
87-A30-190-080 TR,CC5551
87-A30-256-010 TR,2SD1933
87-A30-255-010 TR,2SB1342
87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551
87-026-231-080 CHIP-TRANSISTER,DTA124XK
87-026-237-080 CHIP-TR,DTC124XK
87-A30-104-080 C-TR,RT1N 441C
87-A30-520-080 TR,2SC5342Y
87-A30-090-080 FET,2SK2541
87-A30-091-080 FET,2SJ460
87-A30-062-080 C-TR,KRC104S
87-A30-318-080 TR,CSA952K
87-A30-492-080 TR,2SC5343G
87-A30-234-080 TR,CSC4115BC
89-327-125-080 CHIP TR,2SC2712GR
87-026-580-080 C-TR,DTA123JK
87-026-470-080 C-TR,HN1C03F (0.3W)
89-111-625-080 C-TR,2SA1162GR (0.15W)
87-A30-521-080 C-TR,2SC5345S(O)
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E
89-327-143-080 TR,2SC2714O (0.1W)
DIODE
87-A40-393-090 DIODE,1N5402GW(F20)
87-A40-553-080 DIODE,1N4003 LES
87-A40-777-080 ZENER,UZ30BSB
87-020-465-080 DIODE,1SS133 (110MA)
87-A40-764-080 ZENER,UZ10BSC
87-A40-313-080 C-DIODE,MC 2840
87-A40-269-080 C-DIODE,MC2836
87-A40-270-080 C-DIODE,MC2838
87-017-024-040 C-DIODE,DA204K
87-A40-749-080 ZENER,UZ5.6BSB
87-020-027-080 CHIP-DIODE 1SS184
87-A40-739-080 ZENER,UZ2.7BSA
87-A40-751-080 ZENER,UZ6.2BSB
87-A40-748-080 ZENER,UZ5.6BSA
87-A40-760-080 ZENER,UZ9.1BSA
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
MAIN C.B
C9 87-010-759-080 C-CAP,U, 0.1-25F
C10 87-010-759-080 C-CAP,U, 0.1-25F
C11 87-010-759-080 C-CAP,U, 0.1-25F
C12 87-010-759-080 C-CAP,U, 0.1-25F
C21 87-A10-520-000 CAP,E 3300-35 M SMG
C22 87-016-051-000 CAP,E 2200-35 M SMG
C25 87-010-406-080 CAP, ELECT 22-50
C26 87-010-406-080 CAP, ELECT 22-50
C31 87-010-759-080 C-CAP,U, 0.1-25F
C32 87-012-286-080 CAP, U 0.01-25
C34 87-010-247-080 CAP, ELECT 100-50V
C35 87-010-406-080 CAP, ELECT 22-50
C36 87-010-112-080 CAP, ELECT 100-16V
C50 87-010-247-080 CAP, ELECT 100-50V
C51 87-010-247-080 CAP, ELECT 100-50V
C60 87-010-403-080 CAP, ELECT 3.3-50V
C61 87-010-260-080 CAP, ELECT 47-25V
C81 87-010-401-080 CAP, ELECT 1-50V
C82 87-010-407-080 CAP, ELECT 33-50V
C83 87-010-260-080 CAP, ELECT 47-25V
C101 87-012-282-080 CAP, U 4700P-50
C102 87-012-282-080 CAP, U 4700P-50
C103 87-010-544-080 CAP, ELECT 0.1-50V
C104 87-010-544-080 CAP, ELECT 0.1-50V
C105 87-012-282-080 CAP, U 4700P-50
C106 87-012-282-080 CAP, U 4700P-50
C107 87-010-403-080 CAP, ELECT 3.3-50V
C108 87-010-403-080 CAP, ELECT 3.3-50V
C111 87-010-406-080 CAP, ELECT 22-50
C112 87-010-406-080 CAP, ELECT 22-50
C113 87-A10-946-080 C-CAP,S 220P-100 J CH
C114 87-A10-946-080 C-CAP,S 220P-100 J CH
C117 87-012-286-080 CAP, U 0.01-25
C118 87-012-286-080 CAP, U 0.01-25
C119 87-012-286-080 CAP, U 0.01-25
C120 87-012-286-080 CAP, U 0.01-25
C125 87-010-759-080 C-CAP,U, 0.1-25F
C126 87-010-759-080 C-CAP,U, 0.1-25F
C127 87-010-759-080 C-CAP,U, 0.1-25F
C128 87-010-759-080 C-CAP,U, 0.1-25F
C140 87-010-190-080 S CHIP F 0.01
C401 87-010-759-080 C-CAP,U, 0.1-25F
C402 87-010-759-080 C-CAP,U, 0.1-25F
C403 87-012-193-080 C-CAP,U 82P-50 CH
C404 87-012-193-080 C-CAP,U 82P-50 CH
C405 87-012-286-080 CAP, U 0.01-25
C406 87-012-286-080 CAP, U 0.01-25
C407 87-012-286-080 CAP, U 0.01-25
C408 87-012-286-080 CAP, U 0.01-25
C409 87-012-278-080 C-CAP,U 2200P-50 B
C410 87-012-278-080 C-CAP,U 2200P-50 B
C411 87-010-405-080 CAP, ELECT 10-50V
C412 87-010-405-080 CAP, ELECT 10-50V
C413 87-012-286-080 CAP, U 0.01-25
C421 87-012-275-080 C-CAP,U 1200P-50 B
C422 87-012-275-080 C-CAP,U 1200P-50 B
C423 87-012-274-080 CHIP CAP,U 1000P-50B
C424 87-012-274-080 CHIP CAP,U 1000P-50B
C425 87-010-263-080 CAP, ELECT 100-10V
C426 87-010-263-080 CAP, ELECT 100-10V
C427 87-012-188-080 C-CAP,U 47P-50 CH
C428 87-012-188-080 C-CAP,U 47P-50 CH
C429 87-010-598-080 C-CAP,S 0.068-16VRK
C430 87-010-598-080 C-CAP,S 0.068-16VRK
C431 87-012-284-080 CAP, U 6800P-50
C432 87-012-284-080 CAP, U 6800P-50
C433 87-010-546-080 CAP, ELECT 0.33-50V
C434 87-010-546-080 CAP, ELECT 0.33-50V
C435 87-010-263-080 CAP, ELECT 100-10V
DESCRIPTIONREF. NO. KANRI
– 6 –
Page 7
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
C441 87-010-759-080 C-CAP,U, 0.1-25F
C442 87-010-759-080 C-CAP,U, 0.1-25F
C443 87-010-759-080 C-CAP,U, 0.1-25F
C445 87-A10-039-080 C-CAP,U 470P-50 J CH
C452 87-010-382-080 CAP, ELECT 22-25V
C453 87-012-279-080 C-CAP,U 2700P-50 B
C454 87-012-279-080 C-CAP,U 2700P-50 B
C455 87-012-279-080 C-CAP,U 2700P-50 B
C456 87-012-286-080 CAP, U 0.01-25
C460 87-010-759-080 C-CAP,U, 0.1-25F
C461 87-012-158-080 C-CAP,S 390P-50 CH
C462 87-012-158-080 C-CAP,S 390P-50 CH
C470 87-A10-039-080 C-CAP,U 470P-50 J CH
C605 87-012-275-080 C-CAP,U 1200P-50 B
C606 87-012-275-080 C-CAP,U 1200P-50 B
C609 87-010-785-080 C-CAP,U0.015-25BK
C610 87-010-785-080 C-CAP,U0.015-25BK
C611 87-010-545-080 CAP, ELECT 0.22-50V
C612 87-010-545-080 CAP, ELECT 0.22-50V
C613 87-010-545-080 CAP, ELECT 0.22-50V
C614 87-010-545-080 CAP, ELECT 0.22-50V
C615 87-012-172-080 CAPACITOR CHIP U 10P CH
C616 87-010-248-080 CAP, ELECT 220-10V
C617 87-016-459-080 CAP,E 470-10 SMG
C618 87-010-405-080 CAP, ELECT 10-50V
C630 87-A10-248-080 C-CAP,U0.1-16KBR
C669 87-012-195-080 C-CAP,U 100P-50CH
C670 87-012-195-080 C-CAP,U 100P-50CH
C671 87-010-831-080 C-CAP,U,0.1-16F
C672 87-010-831-080 C-CAP,U,0.1-16F
C673 87-012-278-080 C-CAP,U 2200P-50 B
C677 87-012-286-080 CAP, U 0.01-25
C679 87-A11-112-080 CAP,TC U 1000P-50 J CH
C681 87-010-401-080 CAP, ELECT 1-50V
C682 87-010-759-080 C-CAP,U, 0.1-25F
C683 87-010-260-080 CAP, ELECT 47-25V
C771 87-010-263-080 CAP, ELECT 100-10V
C772 87-012-286-080 CAP, U 0.01-25
C782 87-012-286-080 CAP, U 0.01-25
C783 87-012-286-080 CAP, U 0.01-25
C784 87-012-286-080 CAP, U 0.01-25
C785 87-012-286-080 CAP, U 0.01-25
C786 87-012-286-080 CAP, U 0.01-25
C788 87-012-167-080 C-CAP,U 5P-50 CH
C789 87-A10-801-080 C-CAP,S 0.022-16 J B CM
C790 87-A10-801-080 C-CAP,S 0.022-16 J B CM
C791 87-010-759-080 C-CAP,U, 0.1-25F
C792 87-012-286-080 CAP, U 0.01-25
C793 87-010-404-080 CAP, ELECT 4.7-50V
C795 87-012-286-080 CAP, U 0.01-25
C796 87-012-286-080 CAP, U 0.01-25
C797 87-010-405-080 CAP, ELECT 10-50V
C798 87-012-286-080 CAP, U 0.01-25
C799 87-010-407-080 CAP, ELECT 33-50V
C800 87-010-829-080 CAP, U 0.047-16
C801 87-010-403-080 CAP, ELECT 3.3-50V
C802 87-010-829-080 CAP, U 0.047-16
C803 87-010-787-080 CAP, U 0.022-25
C804 87-010-263-080 CAP, ELECT 100-10V
C807 87-010-400-080 CAP, ELECT 0.47-50V
C808 87-010-401-080 CAP, ELECT 1-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-759-080 C-CAP,U, 0.1-25F
C814 87-012-286-080 CAP, U 0.01-25
C815 87-010-400-080 CAP, ELECT 0.47-50V
C816 87-010-400-080 CAP, ELECT 0.47-50V
C821 87-010-405-080 CAP, ELECT 10-50V
C823 87-010-177-080 C-CAP,S 820P-50 SL
C824 87-010-404-080 CAP, ELECT 4.7-50V
C825 87-010-596-080 CAP, S 0.047-16
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
C836 87-012-286-080 CAP, U 0.01-25
C837 87-012-286-080 CAP, U 0.01-25
C842 87-012-286-080 CAP, U 0.01-25
C844 87-012-286-080 CAP, U 0.01-25
C850 87-010-260-080 CAP, ELECT 47-25V
C851 87-012-286-080 CAP, U 0.01-25
C852 87-012-286-080 CAP, U 0.01-25
C853 87-012-286-080 CAP, U 0.01-25
C858 87-010-759-080 C-CAP,U, 0.1-25F
C859 87-010-759-080 C-CAP,U, 0.1-25F
C860 87-012-286-080 CAP, U 0.01-25
C902 87-018-145-080 CAP,TC-U 6.8P-50 CH
C908 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C909 87-012-349-080 C-CAP,S 1000P-50 CH
C911 87-012-170-080 C-CAP,U 8P-50 CH
C912 87-012-195-080 C-CAP,U 100P-50CH
C913 87-012-286-080 CAP, U 0.01-25
C914 87-012-286-080 CAP, U 0.01-25
C915 87-012-286-080 CAP, U 0.01-25
C918 87-012-165-080 CAP 3P
C920 87-012-180-080 C-CAP,U 22P-50 CH
C921 87-012-186-080 C-CAP,U 39P-50 CH
C922 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C923 87-A10-039-080 C-CAP,U 470P-50 J CH
C924 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C927 87-012-195-080 C-CAP,U 100P-50CH
C961 87-012-170-080 C-CAP,U 8P-50 CH
C962 87-010-401-080 CAP, ELECT 1-50V
C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V
C973 87-012-286-080 CAP, U 0.01-25
C974 87-012-286-080 CAP, U 0.01-25
C979 87-012-195-080 C-CAP,U 100P-50CH
C981 87-010-260-080 CAP, ELECT 47-25V
C982 87-010-759-080 C-CAP,U, 0.1-25F
C983 87-012-286-080 CAP, U 0.01-25
C984 87-012-286-080 CAP, U 0.01-25
C987 87-012-286-080 CAP, U 0.01-25
C990 87-012-195-080 C-CAP,U 100P-50CH
C991 87-012-176-080 CAP 15P
C992 87-012-176-080 CAP 15P
C993 87-012-274-080 CHIP CAP,U 1000P-50B
C994 87-012-195-080 C-CAP,U 100P-50CH
C995 87-012-274-080 CHIP CAP,U 1000P-50B
C996 87-012-195-080 C-CAP,U 100P-50CH
C997 87-010-759-080 C-CAP,U, 0.1-25F
C998 87-010-260-080 CAP, ELECT 47-25V
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER, SFE10.7MA5-A
CF832 87-008-261-010 FILTER, SFE10.7MA5-A
CN81 87-009-030-010 CONNECTOR 2P PH M
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN401 87-A60-620-010 CONN,3P V 2MM JMT
CN601 87-099-194-010 CONN,6P 6216V
CNA351 8A-NEC-634-010 CONN ASSY,8P RPB
CNA401 8A-NEC-633-010 CONN ASSY,3P (PH)
D902 87-A40-916-040 C-VARI-CAP,HVC202A
D903 87-A40-916-040 C-VARI-CAP,HVC202A
!
F101 87-035-223-010 FUSE, 1.25AT
!
FC101 87-033-213-080 CLAMP, FUSE
!
FC102 87-033-213-080 CLAMP, FUSE
FC601 88-906-201-110 FF-CABLE,6P 1.25
J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC
J103 87-A61-452-010 TERMINAL,SP 4P(MSC)
J271 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02
L101 87-A50-610-010 COIL,1UH K(MDEC)
L102 87-A50-610-010 COIL,1UH K(MDEC)
L451 87-007-342-010 COIL,OSC 85K BIAS
– 7 –
Page 8
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)
L832 87-005-847-080 COIL,2.2UH(CECS)
L903 88-ZA1-602-110 COIL,FM-RF-U2 2G
L904 88-ZA1-601-010 COIL,FM-RF-U1 2G
L906 87-005-847-080 COIL,2.2UH(CECS)
L907 8A-NEC-611-010 COIL,FM OSC U 2G
L908 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS)
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)
!
PT101 8A-NHC-605-010 PT,ANH-C HR
R129 87-A00-258-080 RES,M/F 0.22-1W J
R130 87-A00-258-080 RES,M/F 0.22-1W J
R790 87-012-286-080 CAP, U 0.01-25
RY101 87-045-389-010 RELAY,OSA-SS-212DM5
!
S1 87-A90-165-010 SW,SL 1-2-3 SWS2301
!
T101 87-A60-317-010 TERMINAL, 1P MSC
!
T102 87-A60-317-010 TERMINAL, 1P MSC
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
FRONT C.B
C201 87-010-401-040 CAP,E 1-50 SME
C202 87-010-759-080 C-CAP,U, 0.1-25F
C203 87-010-260-040 CAP,E 47-25 SME
C204 87-016-251-040 CAP,E 220-16 SMG
C271 87-012-282-080 CAP, U 4700P-50
C272 87-010-112-040 CAP,E 100-16
C273 87-010-545-040 CAP,E 0.22-50 SME
C274 87-012-195-080 C-CAP,U 100P-50CH
C275 87-010-545-040 CAP,E 0.22-50 SME
C276 87-A10-248-080 C-CAP,U0.1-16KBR
C277 87-010-405-040 CAP,E 10-50
C278 87-012-195-080 C-CAP,U 100P-50CH
C279 87-010-405-040 CAP,E 10-50
C280 87-010-759-080 C-CAP,U, 0.1-25F
C281 87-010-177-080 C-CAP,S 820P-50 SL
C282 87-010-177-080 C-CAP,S 820P-50 SL
C500 87-010-759-080 C-CAP,U, 0.1-25F
C505 87-010-829-080 CAP, U 0.047-16
C506 87-010-263-040 CAP,E 100-10
C507 87-010-246-040 CAP,E 47-35 SME
C508 87-010-192-080 C-CAP,S 0.022-50 F
C509 87-010-404-040 CAP,E 4.7-50 SME
C510 87-010-404-040 CAP,E 4.7-50 SME
C511 87-010-759-080 C-CAP,U, 0.1-25F
C512 87-010-263-040 CAP,E 100-10
C514 87-012-274-080 CHIP CAP,U 1000P-50B
C515 87-012-274-080 CHIP CAP,U 1000P-50B
C517 87-010-759-080 C-CAP,U, 0.1-25F
C518 87-012-268-080 C-CAP,U 330P-50 B
C523 87-010-248-040 CAP,E 220-10 SME
C524 87-010-192-080 C-CAP,S 0.022-50 F
C525 87-010-401-040 CAP,E 1-50 SME
C526 87-012-172-080 CAPACITOR CHIP U 10P CH
C527 87-012-274-080 CHIP CAP,U 1000P-50B
C528 87-010-175-080 CAP 560P
C530 87-012-195-080 C-CAP,U 100P-50CH
C531 87-012-195-080 C-CAP,U 100P-50CH
C532 87-012-195-080 C-CAP,U 100P-50CH
C533 87-012-195-080 C-CAP,U 100P-50CH
C534 87-012-195-080 C-CAP,U 100P-50CH
C535 87-012-195-080 C-CAP,U 100P-50CH
C536 87-012-195-080 C-CAP,U 100P-50CH
C537 87-012-195-080 C-CAP,U 100P-50CH
C538 87-012-195-080 C-CAP,U 100P-50CH
C539 87-012-199-080 CAP 220P
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
C540 87-010-759-080 C-CAP,U, 0.1-25F
C541 87-016-459-040 CAP,E 470-10 SMG
C543 87-010-405-040 CAP,E 10-50
C590 87-010-384-040 CAP,E 100-25 SME
CN201 87-A60-058-010 CONN,10P V 9604S-10C
CN501 87-A60-673-010 CONN,9P H 2MM JMT
EMI271 87-008-372-080 FILTER, EMI BL OIRNI
FC201 88-910-231-110 FF-CABLE,10P 1.25 230MM
FL501 8A-NEC-601-010 FL,HNA-10SS15T
L501 87-A50-655-010 COIL,CLK 4.19MHZ (TOKO)7KLY
S201 87-A90-095-080 SW,TACT EVQ11G04M
S202 87-A90-095-080 SW,TACT EVQ11G04M
S203 87-A90-095-080 SW,TACT EVQ11G04M
S204 87-A90-095-080 SW,TACT EVQ11G04M
S205 87-A90-095-080 SW,TACT EVQ11G04M
S206 87-A90-095-080 SW,TACT EVQ11G04M
S208 87-A90-095-080 SW,TACT EVQ11G04M
S209 87-A90-095-080 SW,TACT EVQ11G04M
S210 87-A90-095-080 SW,TACT EVQ11G04M
S211 87-A90-095-080 SW,TACT EVQ11G04M
S212 87-A90-095-080 SW,TACT EVQ11G04M
S213 87-A90-095-080 SW,TACT EVQ11G04M
SFR501 87-024-431-080 SFR,3.3K RH063EC
VR271 87-NB7-602-010 VR,RTRY 10KAX1 1 V
CD C.B
C1 87-A10-222-040 CAP,AS 22-10 OS
C2 87-010-759-080 C-CAP,U, 0.1-25F
C3 87-010-260-080 CAP, ELECT 47-25V
C4 87-A10-222-040 CAP,AS 22-10 OS
C5 87-012-286-080 CAP, U 0.01-25
C6 87-010-405-080 CAP, ELECT 10-50V
C7 87-010-263-080 CAP, ELECT 100-10V
C8 87-012-274-080 CHIP CAP,U 1000P-50B
C10 87-010-546-080 CAP, ELECT 0.33-50V
C11 87-010-401-080 CAP, ELECT 1-50V
C13 87-012-193-080 C-CAP,U 82P-50 CH
C15 87-012-286-080 CAP, U 0.01-25
C16 87-010-260-080 CAP, ELECT 47-25V
C101 87-A10-504-080 C-CAP,U 0.047-16 K B
C102 87-010-401-080 CAP, ELECT 1-50V
C103 87-010-759-080 C-CAP,U, 0.1-25F
C104 87-010-759-080 C-CAP,U, 0.1-25F
C105 87-010-260-080 CAP, ELECT 47-25V
C106 87-012-195-080 C-CAP,U 100P-50CH
C107 87-010-759-080 C-CAP,U, 0.1-25F
C108 87-012-282-080 CAP, U 4700P-50
C109 87-A10-504-080 C-CAP,U 0.047-16 K B
C110 87-012-195-080 C-CAP,U 100P-50CH
C111 87-010-260-080 CAP, ELECT 47-25V
C112 87-012-286-080 CAP, U 0.01-25
C114 87-010-260-080 CAP, ELECT 47-25V
C115 87-012-286-080 CAP, U 0.01-25
C118 87-010-263-080 CAP, ELECT 100-10V
C119 87-012-286-080 CAP, U 0.01-25
C120 87-012-286-080 CAP, U 0.01-25
C123 87-A10-504-080 C-CAP,U 0.047-16 K B
C124 87-010-403-080 CAP, ELECT 3.3-50V
C125 87-010-759-080 C-CAP,U, 0.1-25F
C135 87-012-195-080 C-CAP,U 100P-50CH
C201 87-A10-248-080 C-CAP,U0.1-16KBR
C206 87-012-195-080 C-CAP,U 100P-50CH
C207 87-012-195-080 C-CAP,U 100P-50CH
C208 87-012-195-080 C-CAP,U 100P-50CH
C209 87-012-195-080 C-CAP,U 100P-50CH
C210 87-A10-248-080 C-CAP,U0.1-16KBR
C211 87-010-263-080 CAP, ELECT 100-10V
C213 87-010-190-080 S CHIP F 0.01
C214 87-010-759-080 C-CAP,U, 0.1-25F
– 8 –
Page 9
PART NO.
NO.
C306 87-010-112-080 CAP, ELECT 100-16V
C307 87-010-759-080 C-CAP,U, 0.1-25F
C308 87-010-263-080 CAP, ELECT 100-10V
C309 87-010-759-080 C-CAP,U, 0.1-25F
C310 87-010-263-080 CAP, ELECT 100-10V
C311 87-010-759-080 C-CAP,U, 0.1-25F
C401 87-010-101-080 CAP, ELECT 220-16
C402 87-010-759-080 C-CAP,U, 0.1-25F
C403 87-010-759-080 C-CAP,U, 0.1-25F
C404 87-010-759-080 C-CAP,U, 0.1-25F
C405 87-010-759-080 C-CAP,U, 0.1-25F
C406 87-010-759-080 C-CAP,U, 0.1-25F
C501 87-012-286-080 CAP, U 0.01-25
C502 87-012-286-080 CAP, U 0.01-25
C503 87-012-286-080 CAP, U 0.01-25
C504 87-012-172-080 CAPACITOR CHIP U 10P CH
C505 87-012-172-080 CAPACITOR CHIP U 10P CH
C506 87-012-286-080 CAP, U 0.01-25
C508 87-010-263-080 CAP, ELECT 100-10V
C509 87-016-669-080 C-CAP,S 0.1-25 K B
C510 87-010-263-080 CAP, ELECT 100-10V
C511 87-010-759-080 C-CAP,U, 0.1-25F
C512 87-012-286-080 CAP, U 0.01-25
C513 87-012-286-080 CAP, U 0.01-25
C514 87-012-286-080 CAP, U 0.01-25
C518 87-012-195-080 C-CAP,U 100P-50CH
C519 87-012-145-080 CAP, CHIP S 270P CH
C520 87-012-157-080 C-CAP,S 330P-50 CH
C521 87-012-197-080 C-CAP,U 150P-50 CH
C523 87-012-286-080 CAP, U 0.01-25
C524 87-012-286-080 CAP, U 0.01-25
C525 87-012-286-080 CAP, U 0.01-25
C526 87-012-286-080 CAP, U 0.01-25
C527 87-012-286-080 CAP, U 0.01-25
C528 87-012-286-080 CAP, U 0.01-25
C529 87-012-286-080 CAP, U 0.01-25
C530 87-012-286-080 CAP, U 0.01-25
C531 87-012-286-080 CAP, U 0.01-25
C532 87-010-374-040 CAP,E 47-10
C533 87-012-286-080 CAP, U 0.01-25
C534 87-010-263-080 CAP, ELECT 100-10V
C535 87-012-286-080 CAP, U 0.01-25
C536 87-010-078-040 CAP,E 47-6.3 5L
C537 87-010-190-080 S CHIP F 0.01
C538 87-010-759-080 C-CAP,U, 0.1-25F
C539 87-010-759-080 C-CAP,U, 0.1-25F
C540 87-010-078-040 CAP,E 47-6.3 5L
C541 87-012-286-080 CAP, U 0.01-25
C542 87-012-188-080 C-CAP,U 47P-50 CH
C544 87-012-286-080 CAP, U 0.01-25
C546 87-012-286-080 CAP, U 0.01-25
C560 87-010-759-080 C-CAP,U, 0.1-25F
C601 87-012-286-080 CAP, U 0.01-25
C602 87-012-286-080 CAP, U 0.01-25
C603 87-010-112-080 CAP, ELECT 100-16V
C604 87-010-759-080 C-CAP,U, 0.1-25F
C605 87-012-286-080 CAP, U 0.01-25
C606 87-012-286-080 CAP, U 0.01-25
C607 87-012-178-080 C-CAP,U 18P-50 CH
C608 87-012-178-080 C-CAP,U 18P-50 CH
C609 87-012-274-080 CHIP CAP,U 1000P-50B
C610 87-012-274-080 CHIP CAP,U 1000P-50B
C611 87-012-274-080 CHIP CAP,U 1000P-50B
C612 87-012-274-080 CHIP CAP,U 1000P-50B
C613 87-010-403-040 CAP,E 3.3-50 SME
C614 87-010-403-040 CAP,E 3.3-50 SME
C615 87-012-188-080 C-CAP,U 47P-50 CH
C616 87-012-188-080 C-CAP,U 47P-50 CH
C617 87-012-286-080 CAP, U 0.01-25
C618 87-010-112-080 CAP, ELECT 100-16V
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C619 87-012-286-080 CAP, U 0.01-25
C701 87-012-196-080 C-CAP,U 120P-50 CH
C702 87-010-494-080 CAP ELECT GAS 1/50
C703 87-012-286-080 CAP, U 0.01-25
C704 87-016-526-080 C-CAP,S 0.47-16 BK
C705 87-010-371-080 CAP, ELECT 470-6.3V
C706 87-010-759-080 C-CAP,U, 0.1-25F
C707 87-012-286-080 CAP, U 0.01-25
C708 87-A11-167-080 C-CAP,S 27P-50 F CH
C709 87-A11-167-080 C-CAP,S 27P-50 F CH
CN1 87-A60-424-010 CONN,16P V TOC-B
CN301 87-099-199-010 CONN,6P 6216 H
CN401 87-099-199-010 CONN,6P 6216 H
CN403 87-A60-077-010 CONN,10P H 9604S-10F
CN404 87-A60-082-010 CONN,05P H 9604S-05F
FB501 87-008-372-080 FILTER, EMI BL OIRNI
FC1 8A-NHC-603-010 FF-CABLE,16P -1.0
FC401 88-906-121-110 FF-CABLE,6P
FC404 88-905-201-110 FF-CABLE, 5P 1.25
J701 87-009-502-010 JACK,PIN 1P Y EARTH
JR302 87-005-778-080 C-COIL,10UK NLC25
L502 87-005-204-080 COIL,47UH
L503 87-005-189-080 COIL 2.7UH
L504 87-005-187-080 COIL,1.8UH
L505 87-005-204-080 COIL,47UH
L506 87-005-204-080 COIL,47UH
L507 87-005-204-080 COIL,47UH
L508 87-005-196-080 COIL,10UH
L701 87-005-817-080 C-COIL, 33UH J FLC32
R507 87-A00-408-080 C-RES,S 2K-1/10W D
R536 87-012-286-080 CAP, U 0.01-25
S201 87-A90-162-010 SW,SL 1-1-3 SSSU
X201 87-A70-124-080 VIB,CER 8.0MHZ
X501 87-A70-125-080 VIB,XTAL 27MHZ 50PPM
X601 87-030-270-080 VIB,XTAL 16.9344MHZ
CD LOAD C.B
CON6 87-099-210-010 CONN,5P 6216H
M1 87-045-305-010 MOTOR,RF-500TB DC-5V(2MA)
SW1 87-036-110-010 PUSH SWITCH
SW2 87-036-110-010 PUSH SWITCH
CD DRIVE C.B
CON3 87-A60-086-010 CONN,6P H 6216
M20 87-045-358-010 MOT,RF-310TA 43
M21 87-045-356-010 MOT,RF-310TA 30
SW1 87-A90-042-010 SW,LEAF MSW-17310MVPO
DESCRIPTIONREF. NO. KANRI
– 9 –
Page 10
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
E C B
E C B
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
E C B B C E
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
CC5551
CSA952K
KTA1266GR
KTC3198GR
S D G
2SJ460
2SK2541
2SC5342Y
2SC5343G
C1
E1
B1
C2
HN1C03F
B2
E2
CSC4115BC
D
G
2SK360E
2SB1342
2SB1370
2SD1933
S
B
2SA1162GR
2SA1235F
2SC2712GR
2SC2714O
2SC3052F
2SC5345S(0)
CMBT5401
C
E
DTA123JK
DTA124XK
DTC124XK
KRA107S
KRC104S
RT1N441C
RT1P141C
CMBT5551
– 10 –
Page 11
WIRING – 1 (MAIN/FRONT)
(K-SCAN)
5
1
43
IMP: 6
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 11 –
R
S
T
U
Page 12
SCHEMATIC DIAGRAM _ 1 (MAIN 1 / 2 : AMP SECTION)
12
Page 13
SCHEMATIC DIAGRAM _ 2 (MAIN 2 / 2 : TUNER SECTION)
13
Page 14
SCHEMATIC DIAGRAM _ 3 (FRONT)
14
Page 15
WIRING 2 (CD) <1 / 2>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
15
R
S
T
U
Page 16
WIRING 2 (CD) <2 / 2>
1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
16
Page 17
SCHEMATIC DIAGRAM _ 4 (CD : 1 / 2 / CD LOAD / CD DRIVE)
17
Page 18
SCHEMATIC DIAGRAM _ 5 (CD : 2 / 2)
18
Page 19
WIRING – 3 (DECK)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 19 –
R
S
T
U
Page 20
WIRING 3 (CD LOAD/CD DRIVE)
151413121110987654321
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
20
R
S
T
U
Page 21
FL (HNA-10SS15T) GRID ASSIGNMENT & ANODE CONNECTION
GRID ASSIGNMENT
ANODE CONNECTION
21
Page 22
IC BLOCK DIAGRAM
22
Page 23
23
Page 24
IC DESCRIPTION
IC, M38B57MCH - E260FP
DescriptionPin No. Pin Name I/O
1 NC — Connected to GND through a resistor.
2 I-HOLD I Hold input.
3 I-TRAY SW I CD tray SW AD input.
4 I-D-SW I CD door open/close AD detection input. (Connected to GND through a resistor)
5 I-KEY2 I Key AD input 2.
6 I-KEY1 I Key AD input 1.
7 O-DSP DATA — Not used.
8 O-MOTOR O Cassette deck motor control output.
9 I-RMC I System remote control signal input. (Active "L")
10 RESET I Reset input for MICON.
11 I-STEREO I Tuner stereo detect input.
12
13 VSS — Connected to GND.
14 XIN I 4.19MHZ oscillator circuit.
15 XOUT O 4.19MHZ oscillator circuit.
16 VCC — Power supply.
17 O-PB1 O Cassette deck output switching PB1/PB2.
18 O-POWER O Power control ON/OFF output.
19 O-C.SHIFT O Clock shift output for micro computer when tuner receiving broadcast.
20 O-RMT O REC MUTE output.
21 O-BIAS O Bias ON/OFF output.
22 O-TU ON O Tuner power supply ON/OFF output.
23 O-CD ON O CD power supply ON/OFF output.
24 O-CLK O PLL IC clock output.
25 I-TM BASE I Reference clock input for timer switch.
26 O-CLOSE O CD tray close data output.
27 O-OPEN O CD tray open data output.
28 VEE — Power supply for FL display.
29 O-STB (DSP) — Not used.
O-DSC/
O-PLL.DATA
O Function IC control output/PLL data output.
30 O-K-SCAN O Initial scan output.
31 O.PLL_CE O Tuner PLL IC chip enable output.
32 NC — Not connected.
33 G10 O FL grid output (G10).
34 G9 O FL grid output (G9).
35 G8 O FL grid output (G8).
36 G7 O FL grid output (G7).
37 G6 O FL grid output (G6).
38 G5 O FL grid output (G5).
39 G4 O FL grid output (G4).
40 G3 O FL grid output (G3).
41 G2 O FL grid output (G2).
– 24 –
Page 25
42 G1 O FL grid output (G1).
43 P22 — Not used.
44 P21 — Not used.
DescriptionPin No. Pin Name I/O
45 P20 O
46 P19 O
47 P18 O
48 P17 O
49 P16 O
50 P15 O
51 P14 O
52 P13 O
53 P12 O
54 P11 O
55 P10 O
56 P9 O
57 P8 O
58 P7 O
59 P6 O
60 P5 O
61 P4 O
62 I-TU3/P3 I/O
63 I-TU2/P2 I/O
64 I-TU1/P1 I/O
65 NC — Not connected.
FL segment output (P20).
FL segment output (P19).
FL segment output (P18).
FL segment output (P17).
FL segment output (P16).
FL segment output (P15).
FL segment output (P14).
FL segment output (P13).
FL segment output (P12).
FL segment output (P11).
FL segment output (P10).
FL segment output (P9).
FL segment output (P8).
FL segment output (P7).
FL segment output (P6).
FL segment output (P5).
FL segment output (P4).
TU3 diode input/FL segment output (P3).
TU2 diode input/FL segment output (P2).
TU1 diode input/FL segment output (P1).
66 NC — Not connected.
67 I-SD(V-CD) I CD IC control data input.
68 I/O BUSY(V-CD) O CD I/O BUSY line.
69 NC I Not connected.
70 NC O Not connected.
71 O-SD(V-CD) O CD IC control data output.
72 I-TUNE/IFC I Tuner SD detection input/Tuner IF count input.
73 AVSS —
74 VREF — Power supply.
75 O-CLK(V-CD) O CD IC clock output.
76 NC — Connected to GND through a capacitor.
77 NC — Connected to GND through a capacitor.
78 NC — Not connected.
79 NC — Connected to GND through a capacitor.
80 I-TP.SW I Deck mechanism SW AD input.
Connected to GND.
– 25 –
Page 26
IC, LC78635E
DescriptionPin No. Pin Name I/O
1 PDO1 O Internal VCO control phase comparator output pin. (Pull down)
2 PDO2 O
3 VVSS — Internal VCO ground pin.
4 PCKIST — PDO output current adjustment resistor connection pin.
5 VVDD — Internal VCO power supply pin.
6 FR — VCO frequency range adjustment resistor connection pin. (Pull up)
7 HFL I Mirror detection signal input pin.
8 SLCIST — SLCO output current adjustment resistor connection pin.
9 SLCO O Control output.
10 EFMIN I EFM signal input pin.
11 JITTV O Jitter detection monitor pin. (Not used)
12 JITTC O Jitter detection monitor pin. (Pull down)
13 BH I BH signal input pin. (Connected to GND)
14 PH (RFENV) I PH signal or RFENV signal input pin.
15 FE I FE signal input pin.
16 TE I TE signal input pin.
17 VREF I VREF input pin.
18 ADAVDD — Servo A/D, D/A power supply pin.
19 ADAVSS — Servo A/D, D/A ground pin.
20 PHREF O PH reference output pin. (Not used)
21 BHREF O BH reference output pin. (Not used)
22 TBLO O Tracking balance output pin.
23 TDO O Tracking control output pin.
24 FDO O Focus control output pin.
25 SPDO O Spindle control output pin.
26 SLDO O Thread control output pin.
27 FG I/O Output driver VREF output pin. FG signal input pin. (Connected to GND)
28 LASER O Laser ON/OFF control pin.
29 CONT1 I/O General-purpose input/output pin 1.
30 CONT2 I/O General-purpose input/output pin 2.
31 CONT3 I/O General-purpose input/output pin 3.
32 CONT4 I/O General-purpose input/output pin 4.
33 CONT5 I/O General-purpose input/output pin 5. (Not used)
34 PCK O EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked. (Not used)
35 C2F — C2 flag output pin.
36 VDD — Digital power supply pin.
37 DOUT O Digital out output pin. (EIAJ format). (Not used)
38 FSX O Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator. (Not used)
Internal VCO control phase comparator output pin.
OFF for rough servo, ON for phase servo. (Pull down)
– 26 –
Page 27
DescriptionPin No. Pin Name I/O
39 EFLG O C1, C2 error correction monitor pin. (Not used)
40 TEST I Test input pin. (Connected to GND)
41 EMPH I/O
42 MUTEL O L channel mute output pin. (Not used)
43 MUTER — R channel mute output pin. (Not used)
44 LVDD — L channel power supply pin.
45 LCHO I L channel output pin. (Not used)
46 LVSS — L channel ground pin.
47 RVSS O R channel ground pin.
48 RCHO I R channel output pin. (Not used)
49 RVDD O R channel power supply pin.
50 XVDD O Crystal oscillator power supply pin.
51 XIN I Connections for a 16.9344MHz crystal oscillator pin.
52 XOUT O Connections for a 16.9344MHz crystal oscillator pin. (Not used)
53 XVSS I Crystal oscillator ground pin.
54 ASLRCK I L/R clock input pin. (Connected to GND)
55 ASDACK I Bit clock input pin. (Connected to GND)
56 ASDFIN — L/R channel data input pin. (Connected to GND)
57 LRSY — L/R clock output pin.
58 DATACK O Bit clock output pin.
59 DATA O L/R channel data output pin.
60 16M O 16.9344MHz output pin.
61 SFSY O
62 SBSY O Subcode clock synchronization signal output pin. (Not used)
63 PW O Subcode P, Q, R, S, T, U and W output pin. (Not used)
64 SBCK I Subcode readout clock input pin. (Connected to GND)
65 CE I Chip enable signal input pin.
66 CL I Data transfer clock input pin.
67 DI I Data input pin.
68 DO O Data output pin.
69 INT O Interruption signal output pin. (Not used)
70 WRQ O Interruption signal output pin.
71 RES I Reset input pin. This pin must be set low briefly after power is first applied.
72 DRF O Focus ON detect pin.
73 VDD5V — Power Supply.
74 VSS — Connected to ground.
75 CONT 6 I/O General-purpose input/output pin 6. (Not used)
76 CONT7 I/O General-purpose input/output pin 7. (Not used)
77 V/P O
Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This
becomes an emphasis monitor pin under control by command.
Subcode frame synchronization signal output pin. This signal falls when the subcode is in the
standby state.
Rough servo/phase control automatic switching monitor output pin.
“H” for rough servo and “L” for phase servo. (Not used)
– 27 –
Page 28
DescriptionPin No. Pin Name I/O
Synchronization signal detection output pin.
78 FSEQ O Outputs a high level when the synchronization signal detected from the EFM signal and the
internally generated synchronization signal agree.
79 DFECT I/O
80 EFMO O EFM signal output pin. (Not used)
Defect pin. Which becomes an input pin after reset and can be controlled externally. This becomes
the defect monitor pin under control by command. (Not used)
– 28 –
Page 29
IC, CL680-D1
Pin No. Pin Name I/O Description
1 NC – Not connected.
2 VSS – GND.
3 CD BCK I Bit clock input from CD DSP.
4 CD DATA I Data input from CD DSP.
5 CD LRCK I LRCK input from CD DSP.
6 CD C2PO I C2 pointer input from CD DSP.
7 ~ 9 NC – Not connected.
10 ~ 15 MD0 ~ MD5 I/O DRAM/ROM interface. (DATA)
16 VSS – Ground.
17 MD6 I/O DRAM/ROM interface. (DATA)
18 VDD3 – Power supply 3.3V.
19 MD7 I/O DRAM/ROM interface. (DATA)
20 VSS – Ground.
21 MD8 I/O DRAM/ROM interface. (DATA)
22 VDD3 – Power supply 3.3V.
23 ~ 29 MD9 ~ MD15 I/O DRAM/ROM interface. (DATA)
30 ~ 36 NC – Not connected.
37 MCE – ROM chip enable.
38 MWE O DRAM write enable.
39 VSS – Ground.
40 CAS O DRAM/ROM interface.
41 VDD3 – Power supply 3.3V.
42 RAS0 O DRAM/ROM interface.
43 RAS1 O DRAM/ROM interface. (Not used)
44 ~ 46 MA10 ~ MA8 O DRAM/ROM interface. (Address)
47 VSS – Ground.
48 MA7 O DRAM/ROM interface. (Address)
49 VDD3 – Power supply 3.3V.
50 ~ 52 MA6 ~ MA4 O DRAM/ROM interface. (Address)
53 VSS – Ground.
54 MA3 O DRAM/ROM interface. (Address)
55 VDD3 – Power supply 3.3V.
56 ~ 58 MA2 ~ MA0 O DRAM/ROM interface. (Address)
59 PGIO7 I/O Programmable I/O. (Not used)
60 RESET I Reset input.
61 VDD MAX IN I Power supply - VDDMAX. (5.0V)
62 ~ 64 NC – Not connected.
65 AGND DAC – Analog ground.
66 AVDD DAC – Analog power supply (DAC) : 3.3V.
67 COMPOS OUT O Composite out.
68 AGND DAC – Analog ground.
– 29 –
Page 30
Pin No. Pin Name I/O Description
69 YOUT O Video signal “Y” OUT. (Not used)
70 AVDD DAC – Analog power supply (DAC) 3.3V.
71 AGND DAC – Analog ground.
72 RREF I Reference resistor input.
73 VREF I Voltage reference input. (Not used)
74 AVDD DAC – Analog power supply (DAC) : 3.3V.
75 C OUT O Video signal “C” out. (Not used)
76 AGND DAC – Analog ground.
77 ~ 79 CLK SEL(0) ~ (2) I Clock selection input.
80 VSS – Ground.
81 CLK SEL(3) I Clock selection input.
82 VDD3 – Power supply 3.3V.
83 ~ 84 CLK SEL(4) ~ (5) I Clock selection input.
85 AGND PLL – Analog ground.
86 DA XCK I DA XCK (16.933MHz) input.
87 AVDD PLL – Analog power supply 3.3V.
88 DA EMP O DAC-emphasis output.
89 ~ 90 PGIO5 ~ 6
91 PGIO0 I/O Programmable I/O. (Not used)
92 PGIO8
93 VSYNC/CSYNC O VSYNC/CSYNC output. (Not used)
94 AVDD PLL – Analog power supply (PLL) 3.3V.
95 NC – Connected to VSS through a resistor.
96 ~ 97 NC – Not connected.
98 AGND PLL – Analog ground.
99 VSS – Ground.
100 NC – Not connected.
101 HSYNC O HSYNC output. (Not used)
102 VDD3 – Power supply 3.3V.
103 VCK OUT O VCK out. (Not used)
104 VSS – Ground.
105 GCK I Global clock signal input. (42.3MHz) (Not used)
106 VCK IN I Video clock signal input. (27.0MHz)
107 GCK OUT O Global clock signal output. (27.0MHz) (Not used)
108 DA LRCK O DAC-LRCK output.
109 VDD MAX OUT – Power supply (VDD MAX) : 5.0V.
110 DA DATA O DAC-PCM data output.
111 DA BCK O DAC-BIT clock output.
112 HD OUT O Micon interface. (Data out)
113 HRDY O Micon interface. (Host ready)
114 HINT O Micon interface. (Host interrupt)
– 30 –
Page 31
Pin No. Pin Name I/O Description
115 CDG SCK I CD-G serial clock input.
116 VSS – Ground.
117 HCK I Micon interface. (Host clock)
118 VDD3 – Power supply 3.3V.
119 HD-IN I Micon interface. (Host data in)
120 VDD3 – Power supply 3.3V.
121 HSEL I Micon interface. (Host select in)
122 CDG SDATA I CD-G data input. (Not used)
123 CDG VFSY I CD-G VFSY input. (Not used)
124 CDG SOSI I CD-G SOSI input.
125 ~ 128 NC – Not connected.
IC, µPD78016FGC-574-AB8
Pin No. Pin Name I/O Description
1 NC – Not connected.
2 AMUTE O Audio analog mute ("H" = Mute ON).
Synchronization signal detection input pin.
3 FSEQ I
4 NC – Not connected.
5 NC – Not connected.
6 EMPH I Emphasis input terminal.
7 DATA IN I Data input pin.
8 NC – Not connected.
9 VSS – GND.
10~12 NC – Connected to GND.
13 EMERG I Power emergency stop (L*3sec = STOP).
14 ~ 19 NC – Not connected.
20 XCDRST O CD reset output terminal.
21 CMND O DATA output pin.
22 CE O Chip enable signal output pin.
23 CL O Data transfer clock output pin.
24 VSS – GND.
Inputs a high level when the synchronization signal detected from the EFM signal and the
internally generated synchronization signal agree. (Not used)
25 DRF I Focus ON detect pin.
26 WRQ I Interruption signal input pin.
27 XBUSY I/O READY/BUSY I/O to HOST OD.
28 ~ 30 NC – Not connected.
31 ~ 34 TST0 ~ TST3 I/O Check Land. (Not used)
35 RESET I Reset.
– 31 –
Page 32
Pin No. Pin Name I/O Description
36 HRDY I HRDY from CL680.
37 XHINT I HINT from CL680
38 NC – Not connected.
39 SCOR I SCOR from CD.
40 VDD – 5.0VDD.
41 XO O
42 XI I
43 VSS – GND.
44 XT2 – Not used.
45 XT1 I Connected to VDD.
46 AVSS – GND.
47 XMPGRST O MPEG block IC reset.
48 HSEL O Address/Data SEL to CL680.
49 NC – Not connected.
50 NT/PAL – NTSC/PAL mode select.
51 OSDXCS O OSD chip select.
52 NC – Connected to GND.
53 CLVSEL I CLV mode select ("H" = CLV-N). (Not used)
54 AADSEL I Auto adjust select ("H" = Auto ON). (Not used)
55 AVDD
– 5.0VDD.
56 AVREF
57 HDOUT I HD-OUT from CL680.
58 HDIN O HD-IN to CL680.
8.0MHz ceralock.
59 HCK O HCK to CL680.
60 OSDDATA O OSD data.
61 OSDCLK O OSD clock.
62 COMMAND I COMMAND from host.
63 STATUS O STATUS to host.
64 SCK I SCK from host.
– 32 –
Page 33
ADJUSTMENT <TUNER / DECK / FRONT>
< TUNER SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to AM 1710kHz and check that the test point is
2160kHz ± 45Hz.
2. AM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to AM 1710kHz, 530kHz and check that the test
point is less than 8.5V (1710kHz) and more than
0.6V (530kHz).
3. FM VT Adjustment
Settings : • Test point : TP1 (VT)
• Adjustment location : L907
Method : Set to FM 108.0MHz and adjust L907 so that the test
point is 7.0V ± 50mV.
4. AM Tracking Adjustment
Settings : • Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location :
L951(1/3) ........................................ 999kHz
Method : Set to AM 1000kHz and adjust L951(1/3) to MAX.
5. FM Tracking Adjustment
Settings : • Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location : L904
Method : Set to FM 87.5MHz and adjust L904 so that the test
point is maximum.
6. AM IF Adjustment
Settings : • Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location :
L802 ................................................450kHz
7. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance)
: TP5 (Lch), TP6 (Rch) (Distortion)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the
voltage between TP3 and TP4 is 0V ± 0.04V.
Then check the distortion is less than 1.3%
3. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point :TP5 (Lch), TP6 (Rch)
Method : Play back the 315Hz and 8kHz signals of the test
tape and check that the output ratio of the 8kHz
signal with respect to that of the 315Hz signal is
0dB ± 4dB.
4. REC/PB Frequency Response Check (DECK 1)
Settings : • Test tape : TTA–602
• Test point : TP5 (Lch), TP6 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at the TP5,
TP6 becomes 80mV. Record and play back the 1kHz
and 8kHz signal and check that the output of the 8kHz
signals is 0dB ± 5dB with respsct to that of the 1 kHz
signal.
5. REC/PB Sensitivity Check (DECK 1)
Settings : • Test tape : TTA–602
• Test point : TP5 (Lch), TP6 (Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP5, TP6
becomes 8mV. Record and play back the 1kHz signals
and check that the output is –2dB ± 3.5dB.
6. PB Sensitivity Check (DECK 1, Deck 2)
Settings : • Test tape : TTA–200
• Test point :TP5 (Lch), TP6 (Rch)
Method : Play back the test tape and check that the output level of
the test point is 110mV ± 3.5dB.
< FRONT SECTION >
1. µ-CON OSC Adjustment
Settings : • Test point : TP7 and TP8 (GND)
• Adjustment location : L501
Method : Insert AC plug while pressing TUNER function key.
Adjust L501 so that the frequency at the test point is
233.4Hz ± 0.23Hz.
< DECK SECTION >
1. Tape Speed Adjustment (DECK 1)
Settings : • Test tape : TTA–100
• Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location : SFR501
Method : Play back the test tape and adjust SFR501 so that the
frequency counter reads 3000Hz ± 5Hz (FWD) and
± 45Hz (REV) with respect to forward speed.
2. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape
and adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
– 33 –
Page 34
CD TEST MODE
– 34 –
Page 35
MECHANICAL EXPLODED VIEW 1 / 1
22
B
C
B
32
24
B
B
B
19
20
B
B
3ZG-3
B
C
P. W. B
C
A
21
16
A
A
PWB,HLDR WIRE
C
10
11
FL
B
P. W. B
23
31
D
B
H
B
26
E
E
B
B
PWB,HLDR FFC
B
28
G
P. W. B
B
B
B
a
b
B
B
13
C
6
7
4
9
5
3
1
B
14
B
B
29
ZZM-2
15
17
18
B
B
HT-SINK,TR LOW
B
B
B
29
HT-SINK,FIN
B
B
b
F
B
12
a
C
B
27
30
2
3
8
B
B
CX-NVC8 HRJSM
25
(File Name:EXP.EPS)
12/9/22 ANH-C
– 35 –
Page 36
MECHANICAL PARTS LIST 1 / 1
PART NO.
1 8A-NEC-006-010 WINDOW,CASS 1
2 8A-NEC-007-010 WINDOW,CASS 2
3 82-NF7-218-010 SPR-T,CASS
4 8A-NEC-002-010 BOX,CASS 1
5 8A-NEC-003-010 BOX,CASS 2
6 8A-NHC-002-010 WINDOW,DISP HR VCD
7 87-CE3-023-010 BADGE,AIWA 30N SILV
8 86-NFZ-231-010 DMPR,70
9 8Z-NF8-028-110 KNOB,RTRY MIC
10 8A-NHC-005-010 CABI,FR HR VCD
11 8A-NHC-001-010 KEY,POWER VCD
!
12 87-A80-157-010 AC CORD ASSY,E BLK CC
13 8A-NEC-041-010 PLATE,MIC
14 8A-NEC-010-010 KEY,CASS 1
15 8A-NEC-011-010 KEY,CASS 2
16 8A-NFA-208-010 GUIDE,FL 100-25 ANFA
17 8A-NEC-009-010 KEY,OPEN/CLOSE
18 8A-NEC-206-010 HLDR,DECK
19 8A-NEC-004-010 PANEL,TRAY CD
20 8A-NEC-203-010 HLDR,CD L
NO.
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
21 8A-NEC-204-010 HLDR,CD R
22 8A-NEC-015-010 PANEL,TOP
23 8A-NEC-013-010 PANEL,LEFT
24 8A-NHC-003-010 CABI,REAR HRJ VCD
25 8A-NHC-210-010 CABI,BOTTOM VCD
26 8A-NEC-201-110 HLDR,PT
27 8A-NEC-014-010 PANEL,RIGHT
28 8A-NHC-202-010 HLDR,VCD
29 8A-NHC-206-010 HLDR,FAN
30 87-A91-751-010 FAN,DSB0812M-S382 -400MM
31 8A-NHC-201-010 COVER, VCD BOTTOM
32 8A-NHC-203-010 COVER, VCD TOP
A 87-067-822-010 BVT2+3-20 W/O SLOT
B 87-067-703-010 TAPPING SCREW, BVT2+3-10
C 87-067-641-010 UTT2+3-8(W/O SLOT)BL
D 87-571-092-410 TAPPING SCREW, VIT+3-4
E 87-067-975-010 S-SCREW,IT+4-8
F 87-067-001-010 S-SCREW,BVWWST2+3-12 W/O SLOT
G 87-067-579-010 TAPPING SCREW, BVT2+3-8
H 87-067-584-010 TAPPING SCREW, BVT2+3-6
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue
– 36 –
Page 37
TAPE MECHANISM EXPLODED VIEW 1 / 1
54
TERMINAL,LB1
A
2
21
20
13
22
23
b
6
5
28
59
27
25
TERMINAL,LB1
21
20
54
55
29
A
22
23
a
31
30
4
3
6
5
1
59
53
46
17
16
14
15
13
19
18
24
27
26
25
28
B
29
61
55
47
14
15
19
18
17
16
38
10
9
57
58
12
11
8
7
45
44
43
37
34
b
1
51
2
a
12
4
3
1
11
10
9
8
7
57
58
40
53
52
51
47
39
50
56
49
48
42
33
24
46
45
44
43
41
36
26
40
33
37
60
32
34
1
35
38
– 37 –
39
Page 38
TAPE MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 8Z-ZM1-254-310 SPR-C,REEL R
2 8Z-ZM1-225-110 GEAR,REEL R
3 8Z-ZM1-253-210 SPR-C,AUTO SENSOR
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR
5 8Z-ZM1-212-210 LEVER,T-UP
6 8Z-ZM1-245-310 SPR-T,AUTO
7 8Z-ZM1-236-010 CLR,SLIP FF/REW
8 8Z-ZM1-252-110 SPR-C,FF/REW
9 8Z-ZM2-213-010 GEAR,SLIP FR A ZZM-2
10 8Z-ZM1-269-010 FELT,FF/REW 2
11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
12 8Z-ZM1-237-110 LEVER,FF/REW 2
13 8Z-ZM1-209-510 LEVER,PAUSE
14 8Z-ZM1-218-210 LEVER,E-LOCK H
15 8Z-ZM1-256-010 SPR-P,PAUSE
16 8Z-ZM1-244-110 SPR-T,T-UP
17 8Z-ZM1-247-310 SPR-T,PINCH
18 8Z-ZM1-261-110 ROLLER ASSY,PINCH
19 8Z-ZM1-221-210 LEVER,PINCH
20 8Z-ZM1-205-310 LEVER,PLAY
21 8Z-ZM1-248-210 SPR-T,BRG
22 87-A90-403-110 HEAD,RPH MS15R
23 84-ZM2-227-310 SPR-C,AZIMUTH
24 8Z-ZM1-216-110 LEVER,AUTO
25 8Z-ZM1-246-110 SPR-T,AUTO 2
26 8Z-ZM2-214-110 GEAR,IDL REW ZZM-2
27 8Z-ZM2-212-010 LEVER,STOP ZZM-2
28 8Z-ZM1-207-010 LEVER,FF
29 8Z-ZM1-206-010 LEVER,REW
30 8Z-ZM1-210-010 LEVER,REC
31 87-A90-404-010 HEAD,EH LE15B
32 8Z-ZM2-218-010 LEVER,REC LOCK ZZM-2
33 87-A91-492-010 SW,LEAF MSW18560
34 8Z-ZM1-226-010 GEAR,REEL L
35 8Z-ZM1-241-210 SPR-T,PLAY
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
36 8Z-ZM1-220-110 LEVER,REC SENSOR
37 8Z-ZM1-249-210 SPR-T,FR
38 8Z-ZM1-242-310 SPR-T,FF/REW
39 8Z-ZM3-244-110 GEAR,CAM TD20
40 8Z-ZM1-232-010 GEAR,IDL FF/REW
41 8Z-ZM3-228-110 FLY-WHL,M3
42 8Z-ZM2-601-010 CONN ASSY,9P ZZM-2
43 8Z-ZM1-228-010 GEAR,SLIP T-UP B
44 8Z-ZM1-265-010 FELT,T-UP
45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-210 SPR-C,T-UP SLIP
47 8Z-ZM1-243-310 SPR-T,STOP/PAUSE
48 87-A91-532-010 MOT,MS15U2LW1A
49 8Z-ZM1-235-010 PULLEY,MOT
50 8Z-ZM2-216-010 BELT,MAIN M
51 8Z-ZM1-260-010 SPR-P,CASETTE
52 8Z-ZM2-201-510 CHAS ASSY,ZZM-2
53 8Z-ZM1-255-310 SPR-T,E-LOCK
54 8Z-ZM2-219-010 LEVER,E-OPEN ZZM-2
55 8Z-ZM1-214-310 LEVER,LOCK
56 8Z-ZM2-211-210 FLY-WHL,ZZM-2
57 8Z-ZM1-257-110 SPR-C,F/R
58 8Z-ZM1-275-010 W-L,1.47-4-0.25
59 87-B10-301-010 W-L,1.63-3.2-0.5 SLIT
60 87-A91-494-010 SW,LEAF MSW17820
61 8Z-ZM1-241-010 SPR-T,PLAY
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM2-220-110 V+2.6 ZZM-2
DESCRIPTIONREF. NO. KANRI
– 38 –
Page 39
CD MECHANISM EXPLODED VIEW 1 / 2 (3ZG-3 E8NM)
9
C
F
CUSH-G,
MAIN
15
14
13
CUSH-G,
MAIN
a
11
10
4
6
F
3ZG-2 E3
b
5
7
B
E
8
2
12
D
3
(M1)
MOT
LOADING
MOTOR
PWB
b
a
A
1
– 39 –
Page 40
CD MECHANISM PARTS LIST 1 / 2 (3ZG-3 E8NM)
PART NO.
NO.
1 83-ZG3-224-519 1B HLDR M2
2 83-ZG3-228-619 1C CHAS,L6
3 83-ZG3-208-019 0E PULLEY,MOTOR
4 83-ZG3-213-019 0E LVR,SW
5 83-ZG3-209-619 1A CAM,SLIDE
6 83-ZG3-207-619 0E GEAR,TRAY
7 83-ZG3-204-21M 0E GEAR,C
8 83-ZG3-205-019 0E GEAR,D
9 83-ZG3-211-01K 0E PLATE,DISC
10 83-ZG3-220-21M 0E GEAR,PULLEY 2
11 83-ZG3-214-019 0E BELT,L
12 83-ZG3-229-51K 1C TRAY,CD 2
13 83-ZG3-210-119 1B HLDR,CHUCK
14 83-ZG3-604-010 0E RING,MAG 2
15 83-ZG3-212-019 0E CAP,DISC
DESCRIPTIONREF. NO. KANRI
A 87-067-945-119 0E VFT2+3-12(F10)
B 87-251-071-410 0E U+2.6-4
C 83-ZG3-235-010 0E VFT2+2.6-8
D 87-352-075-219 0E VT2+2.6-10
E 83-ZG3-217-019 0E S-SCREW,GEAR D
F 81-ZG1-254-019 0E S-SCREW,MECH HLDR
– 40 –
Page 41
CD MECHANISM EXPLODED VIEW 2 / 2 (3ZG-2 E3NM)
2
1
3
A
4
6
M21
SW1
5
PWB
CD MECHANISM PARTS LIST 2 / 2 (3ZG-2 E3NM)
PART NO.
NO.
1 83-ZG2-262-010 CHAS ASSY,E3
2 87-A90-836-010 PICKUP,KSS-213F
3 83-ZG2-235-010 GEAR,A3
4 83-ZG2-236-010 GEAR,MOTOR 3
5 83-ZG2-205-310 GEAR,B
6 83-ZG2-253-010 SHAFT,SLIDE 5
A 87-261-032-210 V+2-3
DESCRIPTIONREF. NO. KANRI
– 41 –
Page 42
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
12 3
How to Remove the PANEL, FR
1. Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
– 42 –
Fig-3
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
Page 43
SPEAKER PARTS LIST (SX-NVC8) <YJSL, YJ3SL, YJSK2BL>
PART NO.
NO.
1 8A-NSM-020-010 GRILLE, FRAME ASSY L
2 8A-NSM-008-010 CORD, SPKR
3 8Z-NSY-003-010 CORD, BUSH<YJSK2BL>
4 8A-NSM-604-010 SPKR, 100<YJSL,YJ3SL>
4 8A-NSM-606-010 SPKR, 100<YJSK2BL>
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
1 8A-NHC-901-010 IB,H(ECA)M
2 8A-NHC-701-010 RC UNIT,RC-AAS09
3 87-043-115-010 ANT,FEEDER FM
4 87-006-225-010 ANT,LOOP ANT NC 2
!
5 87-A91-017-010 PLUG,CONVERSION JT-0476
NO.
DESCRIPTIONREF. NO. KANRI
– 43 –
Page 44
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore2000058 0251431
Loading...