Aiwa NSX-VC320 Service Manual

NSX-VC320

HR

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

SYSTEM

NSX-VC320

 This Service Manual is the Revision Publishing and replace Simple Manual

NSX-VC320 <HR>, (S/M Code No. 09-01A-447-0T1).

CD

CASSEIVER

CX-NVC320 RC-BAS09 VS

BASIC TAPE MECHANISM : ZZM-3 PR1NM
BASIC CD MECHANISM : BZG-5 MVSD3NM

SPEAKER

SX-NVC322

REMOTE

CONTROLLER

 If requiring information about the CD mechanism, see Service Manual of

BZG-5, (S/M Code No. 09-00C-353-3N8).

REVISION

S/M Code No. 09-01A-447-0R1

DATA

SPECIFICATIONS

MAIN UNIT CX-NVC320
TUNER
FM tuning range 87.5 MHz to 108 MHz
FM usable sensitivity (IHF) 13.2 dBf
FM antenna terminals 75 ohms (unbalanced)
MW tuning range 530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1602 kHz (9 kHz step)

MW usable sensitivity 350 µV/m
MW antenna Loop antenna
SW tuning range 5.730 MHz - 17.900 MHz
SW usable sensitivity 40 µV/m(IEC)
SW antenna Wire antenna

AMPLIFIER
Power output Rated : 48 W + 48 W

(6 ohms, T.H.D. 1 %, 1 kHz)
Reference : 60 W + 60 W
(6 ohms, T.H.D. 10 %, 1 kHz)

Total harmonic distortion 0.08 % (30 W, 1 kHz, 6 ohms,

DIN AUDIO)

Inputs VIDEO / AUX : 500 mV

MIC : 1.0 mV (10 K ohms)

Outputs SPEAKERS : 6 ohms or more

VIDEO OUT : 1.0 Vp-p (75 ohms)
PHONES : 32 ohms or more

CASSETTE DECK
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz - 15 kHz
Recording system AC bias
Heads Deck 1 : playback x 1

Deck 2 : recording / playback x 1,
erase x 1

DISC PLAYER
Laser Semiconductor laser (λ = 780 nm)
D/A converter 1 bit dual
Signal-to-noise ratio 90 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
Video signal NTSC/PAL color system (selectable)
Video data MPEG 1
Audio data MPEG 1,Layer 2 (VCD)

MPEG 1,Layer 3 (MP3-CD)

GENERAL
Power requirements 120 V/220 - 230 V/240 V AC,

(Switchable), 50 Hz/60 Hz

Power consumption 85 W
Power consumption With ECO mode on : 0.6 W
in standby mode With ECO mode off : 15 W
Dimensions (W x H x D) 260 x 324 x 341.5 mm
Weight 7.0 kg

FRONT SPEAKERS SX-NVC322
Speaker system 3 way, bass reflex (magnetic shielded)
Speaker units Woofer : 140 mm cone

Tweeter : 66 mm cone
Super tweeter : 20 mm ceramic

Impedance 6 ohms
Dimensions (W x H x D) 220 x 324 x 225 mm
Weight 3.6 kg

 Design and specifications are subject to change without notice.

 The word "BBE"and the "BBE symbol" are trademarks of BBE

Sound, Inc.

Under license from BBE Sound,Inc.

 2 

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the

instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE
LENS ON THE OPTICAL PICK-UP BLOCK.

Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of proce­dures other than those specified herin may result in
hazardous radiation exposure.

ATTENTION

Lutillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could

ruin laser diode in the optical block. Be sure

ground body and workbench, and use care the

clothes do not touch the diode.

1) After the connection, remove solder shown in
right figure.

CD PICK-UP Assy PWB

Solder

 3 

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

11

1 Remove the AC power cord.

11
22

2 Connect a discharging resistor at an end of lead wire that

22

has clips at both ends. Connect the other end of the lead
wire to metal chassis.

33

3 Contact the other end of the discharging resistor to the

33

positive (+) side (+VH) of C101. (For two seconds)

44

4 Contact the same end of the discharging resistor as step

44

33

3 to the negative (-) side (-VH) of C102 in the same way.

33

(For two seconds)

55

5 Check that voltage across C101 and C102 has decreased

55

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

3

C101 C102

22

Fig-1

4

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

11

1 Turn on the AC main power.

11
22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22
33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

33

MICROCOMPUTER is judged to be good.

– 4 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.

11

1 Remove the AC power cord.

11

FRONT C.B

18

MICROCOMPUTER

FRONT C.B

22

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22
33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

33

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

15

C113

Short with tweezers.

Fig-2-2

C113

%

*

VSS

VDD

MICRO­COMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

ELECTRICAL MAIN PARTS LIST

REF. NO.

IC

87-A21-269-010 IC,EW732
87-A21-419-040 C-IC,NJM14558MD-TE2
87-A21-893-040 C-IC,NJM14558V-TE2
87-A21-401-040 C-IC,M61503FP
87-A21-695-010 IC,LA1845L

8B-NHK-601-030 C-IC,UPD780228GF-086-3BA
87-A21-218-110 IC,NJL64H380A
87-A21-928-010 IC,LC72131D-N

TRANSISTOR

87-A30-494-080 TR,2SA1980G
87-A30-559-010 TR,CSB1370EF
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-196-080 TR,2SC4115SRS

87-A30-484-080 C-TR,KRA102S
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-190-080 TR,CC5551
87-A30-635-040 C-TR,SBT5401F
87-A30-528-010 TR,2SB1686

87-A30-529-010 TR,2SD2642
87-A30-162-010 FET,2SK2937
87-A30-091-080 FET,2SJ460
87-A30-090-080 FET,2SK2541
87-A30-062-080 C-TR,KRC104S

87-A30-495-080 TR,2SA1981Y
87-A30-087-080 C-FET,2SK2158
87-A30-636-040 C-TR,SBT5551F
87-026-610-080 TR,KTC3198GR
87-A30-288-040 C-TR,DTC114YKA

89-327-143-080 TR,2SC2714O
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E
87-A30-615-080 TR,STC250
87-A30-086-040 C-TR, CSD1306E

87-A30-582-080 TR,CDA1585BC

DIODE

87-A40-393-090 DIODE,1N5402GW(F20)
87-A40-291-080 DIODE,1N4148M (CPT)
87-A40-455-090 DIODE,RL203 GW `
87-A40-553-080 DIODE,1N4003 LES
87-A40-776-080 ZENER,UZ27BSD

87-A40-764-080 ZENER,UZ10BSC
87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-747-080 ZENER,UZ5.1BSB
87-A40-749-080 ZENER,UZ5.6BSB

87-A40-748-080 ZENER,UZ5.6BSA
87-A40-739-080 ZENER,UZ2.7BSA
87-017-149-080 ZENER,HZS6A2LS

MAIN C.B

C3 87-012-368-080 C-CAP,S 0.1-50 F
C4 87-012-368-080 C-CAP,S 0.1-50 F
C5 87-012-368-080 C-CAP,S 0.1-50 F
C6 87-012-368-080 C-CAP,S 0.1-50 F
C9 87-010-759-080 C-CAP,U, 0.1-25F

C10 87-010-759-080 C-CAP,U, 0.1-25F
C11 87-010-759-080 C-CAP,U, 0.1-25F
C12 87-010-759-080 C-CAP,U, 0.1-25F
C19 87-A12-776-090 CAP,E 2200-50 M 85 SKR
C20 87-A12-776-090 CAP,E 2200-50 M 85 SKR

C21 87-A12-777-090 CAP,E 3300-25
C22 87-A12-777-090 CAP,E 3300-25

PART NO. DESCRIPTIONREF. NO. KANRI

KANRI
NO.

DESCRIPTION

PART NO.

NO.

C25 87-A12-072-080 CAP,E 100-25 SMG
C26 87-A12-072-080 CAP,E 100-25 SMG
C27 87-A12-072-080 CAP,E 100-25 SMG
C28 87-A12-072-080 CAP,E 100-25 SMG
C30 87-A12-095-080 CAP,E 100-50

C31 87-A12-062-080 CAP,E 100-10 SMG
C32 87-012-286-080 CAP, U 0.01-25
C34 87-A12-072-080 CAP,E 100-25 SMG
C35 87-A12-071-080 CAP,E 47-25 SMG
C36 87-A12-067-080 CAP,E 330-16 SMG

C38 87-012-286-080 CAP, U 0.01-25
C60 87-A12-089-080 CAP,E 3.3-50 SMG
C61 87-A12-071-080 CAP,E 47-25 SMG
C83 87-A12-074-080 CAP,E 470-25
C97 87-010-831-080 C-CAP,U,0.1-16F

C101 87-012-279-080 C-CAP,U 2700P-50
C102 87-012-279-080 C-CAP,U 2700P-50
C103 87-A12-084-080 CAP,E 0.22-50 SMG
C104 87-A12-084-080 CAP,E 0.22-50 SMG
C107 87-A12-089-080 CAP,E 3.3-50 SMG

C108 87-A12-089-080 CAP,E 3.3-50 SMG
C111 87-A12-077-080 CAP,E 33-35 SMG
C112 87-A12-077-080 CAP,E 33-35 SMG
C113 87-012-195-080 C-CAP,U 100P-50
C114 87-012-195-080 C-CAP,U 100P-50

C117 87-012-368-080 C-CAP,S 0.1-50 F
C118 87-012-368-080 C-CAP,S 0.1-50 F
C119 87-012-286-080 CAP, U 0.01-25
C120 87-012-286-080 CAP, U 0.01-25
C123 87-010-177-080 C-CAP,S 820P-50 SL

C124 87-010-177-080 C-CAP,S 820P-50 SL
C133 87-012-282-080 CAP, U 4700P-50
C140 87-012-278-080 C-CAP,U 2200P-50 B
C186 87-010-759-080 C-CAP,U, 0.1-25F
C187 87-A12-091-080 CAP,E 10-50

C188 87-A12-091-080 CAP,E 10-50
C225 87-010-759-080 C-CAP,S 0.1-25 F
C226 87-010-759-080 C-CAP,S 0.1-25 F
C227 87-010-759-080 C-CAP,S 0.1-25 F
C228 87-010-759-080 C-CAP,S 0.1-25 F

C241 87-010-831-080 C-CAP,U,0.1-16F
C301 87-012-275-080 C-CAP,U 1200P-50 B
C302 87-012-275-080 C-CAP,U 1200P-50 B
C303 87-012-275-080 C-CAP,U 1200P-50 B
C304 87-012-275-080 C-CAP,U 1200P-50 B

C307 87-A12-062-080 CAP,E 100-10 SMG
C308 87-A12-062-080 CAP,E 100-10 SMG
C309 87-012-188-080 C-CAP,U 47P-50 CH
C310 87-012-188-080 C-CAP,U 47P-50 CH
C313 87-012-284-080 CAP, U 6800P-50

C314 87-012-284-080 CAP, U 6800P-50
C315 87-A12-062-080 CAP,E 100-10 SMG
C317 87-A12-085-080 CAP,E 0.33-50 SMG
C318 87-A12-085-080 CAP,E 0.33-50 SMG
C326 87-010-787-080 CAP, U 0.022-25

C327 87-010-831-080 C-CAP,U,0.1-16F
C360 87-A12-087-080 CAP,E 1-50 SMG
C399 87-A10-039-080 C-CAP,U 470P-50 J CH
C401 87-A12-083-080 CAP,E 0.1-50 SMG
C402 87-A12-083-080 CAP,E 0.1-50 SMG

C403 87-012-193-080 C-CAP,U 82P-50 CH
C404 87-012-193-080 C-CAP,U 82P-50 CH
C405 87-012-286-080 CAP, U 0.01-25
C406 87-012-286-080 CAP, U 0.01-25
C407 87-012-286-080 CAP, U 0.01-25

C408 87-012-286-080 CAP, U 0.01-25
C409 87-012-278-080 C-CAP,U 2200P-50 B
C410 87-012-278-080 C-CAP,U 2200P-50 B
C411 87-A12-091-080 CAP,E 10-50 SMG
C412 87-A12-091-080 CAP,E 10-50 SMG

 6 

PART NO.

NO.

C452 87-A12-069-080 CAP,E 22-25 SMG
C453 87-012-279-080 C-CAP,U 2700P-50 B
C454 87-012-279-080 C-CAP,U 2700P-50 B
C455 87-012-279-080 C-CAP,U 2700P-50 B
C456 87-012-286-080 CAP, U 0.01-25

C457 87-A12-361-080 CAP,M 5600P-100 J CP
C458 87-012-274-080 CHIP CAP,U 1000P-50B
C459 87-012-271-080 CAP, U 560P-50
C460 87-010-831-080 C-CAP,U,0.1-16F
C461 87-012-158-080 C-CAP,S 390P-50 CH

C462 87-012-158-080 C-CAP,S 390P-50 CH
C470 87-018-127-080 CAP, CER 470P-50V
C605 87-012-280-080 CAP, U 3300P-50
C606 87-012-280-080 CAP, U 3300P-50
C609 87-010-785-080 C-CAP,U0.015-25BK

C610 87-010-785-080 C-CAP,U0.015-25BK
C611 87-A12-084-080 CAP,E 0.22-50 SMG
C612 87-A12-084-080 CAP,E 0.22-50 SMG
C613 87-A12-084-080 CAP,E 0.22-50 SMG
C614 87-A12-084-080 CAP,E 0.22-50 SMG

C615 87-012-172-080 CAPACITOR CHIP U 10P CH
C616 87-016-459-080 CAP,E 470-10 SMG
C617 87-016-459-080 CAP,E 470-10 SMG
C618 87-A12-091-080 CAP,E 10-50 SMG
C620 87-010-263-080 CAP, ELECT 100-10V

C623 87-A12-084-080 CAP,E 0.22-50 SMG
C624 87-A12-084-080 CAP,E 0.22-50 SMG
C630 87-A11-057-080 C-CAP,U 0.1-16 K B
C631 87-012-281-080 C-CAP,U 3900P-50 B
C632 87-012-281-080 C-CAP,U 3900P-50 B

C633 87-A11-070-080 C-CAP,U 0.033-16 K B
C634 87-A11-070-080 C-CAP,U 0.033-16 K B
C671 87-010-831-080 C-CAP,U 0.1-16 Z F
C672 87-010-831-080 C-CAP,U 0.1-16 Z F
C673 87-012-278-080 C-CAP,U 2200P-50 K B

C677 87-012-286-080 CAP, U 0.01-25
C771 87-A12-062-080 CAP,E 100-10 SMG
C772 87-012-286-080 CAP, U 0.01-25
C782 87-012-286-080 CAP, U 0.01-25
C783 87-012-286-080 CAP, U 0.01-25

C784 87-012-286-080 CAP, U 0.01-25
C785 87-012-286-080 CAP, U 0.01-25
C786 87-012-286-080 CAP, U 0.01-25
C788 87-012-167-080 C-CAP,U 5P-50 CH
C789 87-016-118-080 C-CAP,U 0.022-25

C790 87-016-118-080 C-CAP,U 0.022-25
C791 87-010-831-080 C-CAP,U 0.1-16F
C792 87-012-286-080 CAP, U 0.01-25
C793 87-A12-090-080 CAP,E 4.7-50 SMG
C795 87-012-286-080 CAP, U 0.01-25

C796 87-012-286-080 CAP, U 0.01-25
C797 87-A12-091-080 CAP,E 10-50 SMG
C798 87-012-286-080 CAP, U 0.01-25
C799 87-010-265-080 CAP,E 33-16 M 11L SME
C800 87-010-829-080 CAP, U 0.047-16

C801 87-A12-089-080 CAP,E 3.3-50 SMG
C802 87-010-829-080 CAP, U 0.047-16
C803 87-010-787-080 CAP, U 0.022-25
C804 87-A12-062-080 CAP,E 100-10 SMG
C807 87-A12-086-080 CAP,E 0.47-50 SMG

C808 87-A12-087-080 CAP,E 1-50 SMG
C809 87-A12-087-080 CAP,E 1-50 SMG
C810 87-010-831-080 C-CAP,U,0.1-16F
C814 87-012-286-080 CAP, U 0.01-25
C815 87-A12-086-080 CAP,E 0.47-50 SMG

C816 87-A12-086-080 CAP,E 0.47-50 SMG
C821 87-A12-091-080 CAP,E 10-50 SMG
C823 87-010-177-080 C-CAP,S 820P-50
C824 87-A12-090-080 CAP,E 4.7-50 SMG
C825 87-010-596-080 CAP, S 0.047-16

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C842 87-012-286-080 CAP, U 0.01-25
C843 87-012-286-080 CAP, U 0.01-25
C844 87-012-286-080 CAP, U 0.01-25
C845 87-012-286-080 CAP, U 0.01-25
C846 87-012-286-080 CAP, U 0.01-25

C847 87-012-286-080 CAP, U 0.01-25
C848 87-012-286-080 CAP, U 0.01-25
C849 87-012-286-080 CAP, U 0.01-25
C850 87-A12-071-080 CAP,E 47-25 SMG
C851 87-012-286-080 CAP, U 0.01-25

C852 87-012-286-080 CAP, U 0.01-25
C853 87-012-286-080 CAP, U 0.01-25
C858 87-010-831-080 C-CAP,U,0.1-16F
C901 87-018-145-080 CAP,TC-U 6.8P-50
C904 87-012-286-080 CAP, U 0.01-25

C905 87-012-286-080 CAP, U 0.01-25
C907 87-012-286-080 CAP, U 0.01-25
C908 87-A10-915-080 C-CAP,U 1000P-25
C909 87-012-286-080 CAP, U 0.01-25
C910 87-012-174-080 CAP CHIP U 12P-50

C911 87-012-170-080 C-CAP,U 8P-50
C912 87-012-195-080 C-CAP,U 100P-50
C913 87-012-286-080 CAP, U 0.01-25
C914 87-012-166-080 C-CAP,U 4P-50
C915 87-012-174-080 C-CAP,CERA SS 12P

C916 87-012-180-080 C-CAP,U 22P-50
C917 87-012-186-080 C-CAP,U 39P-50
C918 87-A10-039-080 C-CAP,U 470P-50
C921 87-012-195-080 C-CAP,U 100P-50
C922 87-012-174-080 CAP CHIP CERA SS 12P

C940 87-012-286-080 CAP,U 0.01-25
C941 87-012-180-080 C-CAP,U 22P-50 J CH
C943 87-012-286-080 C-CAP,U 0.01-25 KB
C945 87-012-286-080 C-CAP,U 0.01-25 KB
C946 87-010-971-080 C-CAP,S 4700P-50 JB

C947 87-012-286-080 C-CAP,U 0.01-25 KB
C948 87-012-166-080 C-CAP, U 4P-50 C CH
C952 87-012-286-080 C-CAP,U 0.01-25KB
C953 87-012-286-080 C-CAP,U 0.01-25KB
C954 87-A12-086-080 CAP,E 0.47-50 SMG

C956 87-A12-062-080 CAP,E 100-10 SMG
C959 87-010-831-080 C-CAP,U,0.1-16F
C962 87-A12-087-080 CAP,E 1-50 SMG
C963 87-015-785-080 CHIP CAPACITOR, 0.1-25 Z F
C964 87-010-854-080 C-CAP, S 560P-50 J CH

C971 87-A12-067-080 CAP,E 330-16 SMG
C972 87-A12-090-080 CAP,E 4.7-50 SMG
C973 87-012-286-080 CAP, U 0.01-25
C974 87-012-286-080 CAP, U 0.01-25
C979 87-012-195-080 C-CAP,U 100P-50CH

C981 87-A12-071-080 CAP,E 47-25 SMG
C982 87-010-831-080 C-CAP,U,0.1-16F
C983 87-012-286-080 CAP, U 0.01-25
C984 87-012-286-080 CAP, U 0.01-25
C987 87-012-286-080 CAP, U 0.01-25

C989 87-012-286-080 C-CAP,U 0.01-25 KB
C991 87-012-176-080 CAP 15P
C992 87-012-176-080 CAP 15P
C993 87-012-274-080 CHIP CAP,U 1000P-50B
C995 87-012-274-080 CHIP CAP,U 1000P-50B

C997 87-010-831-080 C-CAP,U,0.1-16F
C998 87-A12-071-080 CAP,E 47-25 SMG
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER,CF SFE10.7MA5
CF832 87-008-261-010 FILTER, SFE10.7MA5-A

CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P H BLK TYK-B(X)
CN604 87-A60-059-010 CONN,08P V 9604S-08C
CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480)

DESCRIPTIONREF. NO. KANRI

 7 

NO.

DESCRIPTIONREF. NO. PART NO.

CNA301 86-ZM3-604-210 CONN ASSY,3P-PB
CNA351 86-ZM3-605-110 CONN ASSY,8P-RPB
D902 87-A40-128-080 C-VARI-CAP,HVU202A
D903 87-A40-128-080 C-VARI-CAP,HVU202A
D951 87-A40-618-080 VARI-CAP, SVC 348 (S/T)

FB600 87-A92-284-010 F-BEAD,E3407MFT2
FB602 87-008-372-010 FLTR, EMIBL01 RN1
FC602 88-908-451-110 FF-CABLE,8P 1.25 450MM
J202 87-A60-488-010 JACK,DIA6.3 BLK ST W/SW KM16AT
J203 87-A60-238-010 TERMINAL,SP 4P (MSC)

J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V
J940 87-A60-633-010 CONN,2P H 2.5MM JMT
JR123 87-012-195-080 C-CAP,U 100P-50
JR124 87-012-195-080 C-CAP,U 100P-50

JW023 87-008-372-010 FLTR, EMIBL01 RN1
JW601 87-008-372-010 FLTR, EMIBL01 RN1
JW641 87-008-372-010 FLTR, EMIBL01 RN1
JW648 87-008-372-010 FLTR, EMIBL01 RN1
L201 87-A50-610-010 COIL,1UH K(MDEC)

L202 87-A50-610-010 COIL,1UH K(MDEC)
L451 87-007-342-010 COIL,OSC 85KHZ BIAS
L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)

L832 87-005-847-080 COIL,2.2UH(CECS)
L902 88-ZA1-602-110 COIL,FM-RF-U2 2G
L903 88-ZA1-601-010 COIL,FM-RF-U1 2G
L904 87-005-847-080 COIL,2.2UH(CECS)
L905 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS)

L906 88-ZA1-603-010 COIL,FM-OSC-U 2G
L941 87-A50-022-010 COIL,ANT SW (COI) 7.96MHZ
L942 87-A50-550-010 COIL,OSC SW-2N (COI)
L943 87-A50-522-080 COIL,1MH K CEC
L944 87-A50-159-010 COIL,10MH K C2B

L952 87-A50-430-010 COIL,ANT MW (3BSW)
L953 87-A50-431-010 COIL,OSC MW (3BSW)
R129 87-A00-257-080 RES,M/F 0.15-1W J
R130 87-A00-257-080 RES,M/F 0.15-1W J
R131 87-A00-257-080 RES,M/F 0.15-1W J

R132 87-A00-257-080 RES,M/F 0.15-1W J
R243 87-A01-001-050 RES,220-1/2W J BLT2J
R244 87-A01-001-050 RES,220-1/2W J BLT2J
R245 87-A00-999-050 RES,180-1/2W J BLT2J
R246 87-A00-999-050 RES,180-1/2W J BLT2J

R790 87-012-286-080 CAP, U 0.01-25
R991 87-012-195-080 C-CAP,U 100P-50CH
R993 87-012-195-080 C-CAP,U 100P-50CH
R995 87-012-195-080 C-CAP,U 100P-50CH
SFR451 87-024-435-080 SFR 33K H RH063EC

SFR452 87-024-435-080 SFR 33K H RH063EC
TC941 87-A91-773-080 TRIMMER, PLY 20P 6.8X 5.4CDYL
TC943 87-A91-774-080 TRIMMER, PLY 30P 6.8X 5.4CDYL
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001

WH1 87-A90-510-010 HLDR,WIRE 2.5-9P
X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST

FRONT C.B

C108 87-010-785-080 C-CAP,U 0.015-25BK
C153 87-010-787-080 CAP, U 0.022-25
C154 87-010-246-040 CAP,E 47-35 SME
C155 87-010-404-040 CAP,E 4.7-50 SME
C156 87-010-404-040 CAP,E 4.7-50 SME

C301 87-012-278-080 C-CAP,U 2200P-50 B
C351 87-A10-353-080 C-CAP,U 0.22-10KB
C361 87-012-274-080 CHIP CAP,U 1000P-50B
C362 87-012-274-080 CHIP CAP,U 1000P-50B
C371 87-012-274-080 CHIP CAP,U 1000P-50B

KANRI
NO.

C372 87-012-274-080 CHIP CAP,U 1000P-50B
C401 87-012-282-080 C-CAP,U 4700P2-50 K B
C402 87-010-112-040 CAP,E 100-16 M 11L SME
C403 87-010-545-040 CAP,E 0.22-50 M 11L SME
C404 87-012-191-080 C-CAP,U 68P-50 J CH

C405 87-010-545-040 CAP,E 0.22-50 M 11L SME
C406 87-010-545-040 CAP,E 0.22-50 M 11L SME
C407 87-010-405-040 CAP,E 10-50 M 11L SME
C408 87-012-195-080 C-CAP,U 100P-50 J CH
C409 87-010-265-040 CAP,E 33-16 M 11L SME

C410 87-012-369-080 C-CAP,S 0.047-50 Z F
C413 87-010-177-080 C-CAP,U 820P-50 J SL
C601 87-010-382-040 CAP,E 22-25 SME
C702 87-012-286-080 CAP, U 0.01-25
C801 87-A10-804-080 C-CAP,S 0.1-25 J B

C803 87-012-280-080 CAP, U 3300P-50
C804 87-A10-592-080 C-CAP,S 0.015-50 J B
C805 87-012-184-080 C-CAP,U 33P-50 CH
C806 87-012-274-080 CHIP CAP,U 1000P-50B
C807 87-012-274-080 CHIP CAP,U 1000P-50B

C808 87-010-544-040 CAP,E 0.1-50 SME
C809 87-010-404-040 CAP,E 4.7-50 SME
C810 87-016-114-080 C-CAP,U 0.01-25B
C811 87-A12-052-080 C-CAP,S 0.033-25 J B
C901 87-012-195-080 C-CAP,U 100P-50CH

C902 87-012-195-080 C-CAP,U 100P-50CH
C903 87-012-195-080 C-CAP,U 100P-50CH
C904 87-012-195-080 C-CAP,U 100P-50CH
C905 87-012-195-080 C-CAP,U 100P-50CH
C906 87-012-195-080 C-CAP,U 100P-50CH

C907 87-012-195-080 C-CAP,U 100P-50CH
C908 87-012-195-080 C-CAP,U 100P-50CH
C909 87-012-195-080 C-CAP,U 100P-50CH
C910 87-012-195-080 C-CAP,U 100P-50CH
C911 87-012-274-080 CHIP CAP,U 1000P-50B

C912 87-010-831-080 C-CAP,U,0.1-16F
C913 87-A10-189-040 CAP,E 220-10
C914 87-A10-189-040 CAP,E 220-10
C915 87-010-831-080 C-CAP,U,0.1-16F
C916 87-010-831-080 C-CAP,U,0.1-16F

C917 87-010-831-080 C-CAP,U,0.1-16F
C919 87-012-286-080 CAP, U 0.01-25
C920 87-010-829-080 CAP, U 0.047-16
C921 87-012-282-080 CAP, U 4700P-50
C951 87-012-172-080 CAPACITOR CHIP U 10P CH

C952 87-010-854-080 C-CAP,S 560PCH
C953 87-012-349-080 C-CAP,S 1000P-50 CH
C961 87-010-378-040 CAP,E 10-16
C962 87-012-336-080 CAP, CHIP U 330P SL
C963 87-010-831-080 C-CAP,U,0.1-16F

CN104 87-A60-057-010 CONN,11P V 9604S-11C
CN701 87-099-720-010 CONN,30P TYK-B(P)
CN731 87-099-196-010 CONN,8P 6216 V
EMI401 87-008-372-080 FLTR,EMI BL01 RN1
FB731 87-A92-284-010 F-BEAD,E3407MFT2

FC731 88-908-301-110 FF-CABLE,8P 1.25
FFC104 88-911-101-110 FF-CABLE,11P 1.25
FL901 8B-NFY-605-010 FL,HNA-08LS02
J401 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC
JW402 87-A11-155-080 CAP,TC U 0.01-16 ZF

L951 87-A50-655-010 COIL,CLK 4.19MHZ (TOKO)7KLY
LED209 87-A41-062-040 LED,LTL-1CHEE-012A RED
S321 87-A90-164-080 SW,TACT SKQAB(N)
S322 87-A90-164-080 SW,TACT SKQAB(N)
S323 87-A90-164-080 SW,TACT SKQAB(N)

S324 87-A90-164-080 SW,TACT SKQAB(N)
S325 87-A90-164-080 SW,TACT SKQAB(N)
S326 87-A90-164-080 SW,TACT SKQAB(N)
S327 87-A90-164-080 SW,TACT SKQAB(N)
S328 87-A90-164-080 SW,TACT SKQAB(N)

DESCRIPTIONREF. NO. PART NO.KANRI

 8 

KANRI
NO.

S329 87-A90-164-080 SW,TACT SKQAB(N)
S330 87-A90-164-080 SW,TACT SKQAB(N)
S331 87-A90-164-080 SW,TACT SKQAB(N)
S332 87-A90-164-080 SW,TACT SKQAB(N)
S333 87-A90-164-080 SW,TACT SKQAB(N)

S334 87-A90-164-080 SW,TACT SKQAB(N)
S335 87-A90-164-080 SW,TACT SKQAB(N)
S341 87-A90-164-080 SW,TACT SKQAB(N)
S342 87-A90-164-080 SW,TACT SKQAB(N)
S343 87-A90-164-080 SW,TACT SKQAB(N)

S344 87-A90-164-080 SW,TACT SKQAB(N)
S345 87-A90-164-080 SW,TACT SKQAB(N)
S346 87-A90-164-080 SW,TACT SKQAB(N)
S347 87-A90-164-080 SW,TACT SKQAB(N)
S348 87-A90-164-080 SW,TACT SKQAB(N)

S349 87-A90-164-080 SW,TACT SKQAB(N)
S350 87-A90-164-080 SW,TACT SKQAB(N)
S351 87-A90-164-080 SW,TACT SKQAB(N)
S352 87-A90-164-080 SW,TACT SKQAB(N)
S353 87-A90-164-080 SW,TACT SKQAB(N)

S354 87-A90-164-080 SW,TACT SKQAB(N)
S361 87-A91-633-010 SW,RTRY XRE012103PVB25FINA 1-2
S371 87-A91-632-010 SW,RTRY XRE012103PVB25FINB 1-2
VR401 87-NB7-602-010 VR,RTRY 10KAX1 1 V

DESCRIPTIONREF. NO. PART NO.

PT C.B

CN1 87-A61-110-010 CONN,9P V TID-A
PT1 8B-NHY-601-010 PT,BNH-31 HR

!

PT2 8B-MA6-673-010 PT,SUB BMA H (VRK)

!

RY1 87-A91-339-010 RELAY,AC DC12V G5PA-2

!

S1 87-A90-165-010 SW,SL 1-2-3 SWS2301

!

!

T1 87-A60-317-010 TERMINAL, 1P MSC

!

T2 87-A60-317-010 TERMINAL, 1P MSC

DECK C.B

CN1 87-099-753-010 CONN,11P H 9604
SFR1 87-024-581-010 SFR,3.3K H KVSF637A
SOL1 82-ZM3-627-010 SOL ASSY,27 SO
SOL2 82-ZM3-627-010 SOL ASSY,27 SO
SW1 87-036-109-010 SW,MICRO SPPB61

SW2 87-036-109-010 SW,MICRO SPPB61
SW3 87-036-109-010 SW,MICRO SPPB61
SW4 87-036-109-010 SW,MICRO SPPB61
SW5 87-036-109-010 SW,MICRO SPPB61
W1 82-ZM3-601-010 RBN-CORD,4P-75

NO.

DESCRIPTIONREF. NO. PART NO. KANRI

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

A

Resistor Code

Chip resistor

Wattage Type Tolerance
1/16W 1005 5% CJ

1/16W
1/10W

1/8W

1608
2125

3216

5%
5%

5%

Symbol

CJ
CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

0.55

Resistor Code

108
118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45
2 1.25 0.45

3.2

1.6

: A
: A

 9 

TRANSISTOR ILLUSTRATION

E C B

CC5551
CDA1585BC
KTC3198GR

S D G

2SJ460
2SK2541

E C B

2SA1980G
2SA1981Y
STC250

G D S

2SK2937

E C B

2SC4115 (SRS)

S

D

G

2SK360E

B C E

2SB1686
2SD2642
CSB1370EF

D

G

S

2SK2158

B

2SA1235F
2SC2714(O)
2SC3052F
SBT5401F
SBT5551F
CSD1306E

C

E

DTC114YKA
KRA102S
KRA107S
KRC102S-RTK
KRC104S

 10 