Aiwa NSX-VC120 Service Manual

NSX-VC120

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

SYSTEM

NSX–VC120 RC–BAS09 VS

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual” (S/M Code No. 09-018-448-4T1).

• If requiring information about the CD mechanisim, see Service Manual of BZG-2, (S/M Code No. 09-00C-353-2N6).

CASSEIVER CX–NVC120

BASIC TAPE MECHANISM : ZZM-2 PR1NM BASIC CD MECHANISM : BZG-2 MVSD3NM

SPEAKER

SX–NVC122

REMOTE

CONTROLLER

S/M Code No. 09-01A-448-4R1

REVISION

DATA

SPECIFICATIONS

MAIN UNIT CX-NVC120 TUNER

FM tuning range 87.5 MHz to 108 MHz FM usable sensitivity (IHF) FM antenna terminals 75 ohms (unbalanced) AM tuning range 531 kHz to 1602 kHz (9 kHz step)

AM usable sensitivity 350 AM antenna Loop antenna

13.2 dBf

530 kHz to 1710 kHz (10 kHz step)

mV/m

AMPLIFIER

Power output Rated: 16 W + 16 W

Total harmonic distortion Input VIDEO/AUX: 500 mV

Outputs SPEAKERS: 6 ohms or more

(6 ohms, T.H.D. 1 %, 1 kHz) Reference: 20 W + 20 W (6 ohms, T.H.D. 10 %, 1 kHz)

0.1 % (8 W, 1 kHz, 6 ohms, DIN AUDIO)

MIC: 1.2 mV (10 kohms)

VIDEO OUT: 1.0 Vp-p (75 ohms) PHONES: 32 ohms or more

CASSETTE DECK

Track format 4 tracks, 2 channels stereo Frequency response 50 Hz  8 kHz Recording system AC bias Heads DECK 1: Recording/playback x 1,

DECK 2: Playback x 1

erase x 1

DISC PLAYER

Laser Semiconductor laser ( D/A converter 1 bit dual Signal-to-noise ratio 90 dB (1 kHz, 0 dB) Harmonic distortion 0.05 % (1 kHz, 0 dB) Video signal NTSC/PAL color system (selectable) Video data MPEG 1 Audio data MPEG 1, Layer 2 (VCD)

MPEG 1, Layer 3 (MP3-CD)

l = 780 nm)

GENERAL

Power requirements 120 V/220  230 V/240 V AC,

Power consumption 75 W Dimensions ( W x H x D) 260 x 301 x 292 mm Weight 4.8 kg

(Switchable), 50 Hz/60 Hz

FRONT SPEAKERS SX-NVC122

Speaker system 1 way, bass reflex (magnetic shielded) Speaker units Full range: 100 mm cone Impedance 6 ohms Dimensions (W x H x D) 196 x 301 x 188 mm

Weight: 2.2 kg

• Design and specifications are subject to change without notice.

ACCESSORIES / PACKAGE LIST

PART NO.

1 8B-NHC-901-010 IB,H(ECA)M 2 87-006-268-010 AM-LOOP ANT NC(UN) 3 87-043-115-010 ANT,FEEDER FM 4 8B-NHK-702-010 RC UNIT,RC-BAS09 VS 5 87-A92-262-010 PLUG,CONVERSION WT01011

6 87-A80-167-010 CORD,PIN 1PY 150CM 7 87-A90-173-010 F-BEAD,9-20-21 ZCAT2017-093

NO.

DESCRIPTIONREF. NO. KANRI

 2 

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel: Usynlig laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS – 213F)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in the right figure.

PICKUP Assy PWB

Solder

 3 

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

1 Remove the AC power cord.

11 22

2 Connect a discharging resistor at an end of lead wire that

has clips at both ends. Connect the other end of the lead wire to metal chassis.

3 Contact the other end of the discharging resistor to the

positive (+) side (+VH) of C101. (For two seconds)

4 Contact the same end of the discharging resistor as step

3 to the negative (-) side (-VH) of C102 in the same way.

(For two seconds)

5 Check that voltage across C101 and C102 has decreased

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

C101 C102

Fig-1

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.

11 22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22 33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

MICROCOMPUTER is judged to be good.

– 4 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER.

1 Remove the AC power cord.

FRONT C.B

MICROCOMPUTER

FRONT C.B

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22 33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

C113

Short with tweezers.

Fig-2-2

C113

VSS

VDD

MICROCOMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

ELECTRICAL MAIN PARTS LIST

PART NO. DESCRIPTIONREF. NO. KANRI

87-A21-893-040 C-IC,NJM14558V-TE2 87-A21-419-040 C-IC,NJM14558MD-TE2 8B-NHC-602-030 C-IC,UPD780226GF-026-3BA 87-A21-218-110 IC,NJL64H380A 87-A21-443-040 C-IC,M62495AFP

87-A21-695-010 IC,LA1845L 87-A21-928-010 IC,LC72131D-N

TRANSISTOR

87-A30-494-080 TR,2SA1980G 87-A30-476-010 TR,KTA1046Y 87-A30-075-080 C-TR,2SA1235F 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F

89-322-405-680 TR,2SC2240(GR/BL) 87-A30-256-010 TR,2SD1933 87-A30-255-010 TR,2SB1342 87-A30-635-040 C-TR,SBT5401F 87-A30-636-040 C-TR,SBT5551F

87-A30-090-080 FET,2SK2541 87-A30-234-080 TR,CSC4115BC 87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-495-080 TR,2SA1981Y

87-A30-615-080 TR,STC250 87-A30-521-080 C-TR,2SC5345SF/S(O) 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E 89-327-143-080 C-TR,2SC2714O

DIODE

87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-777-080 ZENER,UZ30BSB 87-A40-291-080 DIODE,1N4148M(CPT) 87-A40-764-080 ZENER,UZ10BSC

87-A40-269-080 C-DIODE,MC2836 87-A40-270-080 C-DIODE,MC2838 87-A40-749-080 ZENER,UZ5.6BSB 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L

87-A40-760-080 ZENER,UZ9.1BSA

MAIN C.B

C9 87-010-759-080 C-CAP,U 0.1-25F C10 87-010-759-080 C-CAP,U 0.1-25F C11 87-010-759-080 C-CAP,U 0.1-25F C12 87-010-759-080 C-CAP,U 0.1-25F C21 87-A12-778-090 CAP,E 3300-35 M 85 SKR

C22 87-A12-781-090 CAP,E 2200-35 M 85 SKR C25 87-A12-092-080 CAP,E 22-50 SMG C26 87-A12-092-080 CAP,E 22-50 SMG C31 87-010-759-080 C-CAP,U 0.1-25F C32 87-012-286-080 C-CAP,U 0.01-25 K B

C34 87-A12-071-080 CAP,E 47-25 SMG C35 87-A12-092-080 CAP,E 22-50 SMG C36 87-A10-918-080 CAP,E 100-16 SMG C50 87-A12-095-080 CAP,E 100-50 SMG C51 87-A12-095-080 CAP,E 100-50 SMG

C60 87-A12-089-080 CAP,E 3.3-50 SMG C61 87-A12-071-080 CAP,E 47-25 SMG C81 87-A12-087-080 CAP,E 1-50 SMG C82 87-A12-093-080 CAP,E 33-50 SMG C83 87-A12-071-080 CAP,E 47-25 SMG

C101 87-012-284-080 C-CAP,U 6800P-50 K B GRM

NO.

DESCRIPTIONREF. NO. KANRI

PART NO.

C102 87-012-284-080 C-CAP,U 6800P-50 K B GRM C103 87-A12-083-080 CAP,E 0.1-50 SMG C104 87-A12-083-080 CAP,E 0.1-50 SMG C105 87-012-282-080 C-CAP,U 4700P-50 K B C106 87-012-282-080 C-CAP,U 4700P-50 K B

C107 87-A12-089-080 CAP,E 3.3-50 SMG C108 87-A12-089-080 CAP,E 3.3-50 SMG C111 87-A12-092-080 CAP,E 22-50 SMG C112 87-A12-092-080 CAP,E 22-50 SMG C113 87-A10-946-080 C-CAP,S 220P-100 J CH

C114 87-A10-946-080 C-CAP,S 220P-100 J CH C117 87-012-286-080 C-CAP,U 0.01-25 K B C118 87-012-286-080 C-CAP,U 0.01-25 K B C119 87-012-286-080 C-CAP,U 0.01-25 K B C120 87-012-286-080 C-CAP,U 0.01-25 K B

C123 87-012-280-080 C-CAP,U 3300P-50 K B C124 87-012-280-080 C-CAP,U 3300P-50 K B C125 87-010-759-080 C-CAP,U 0.1-25F C126 87-010-759-080 C-CAP,U 0.1-25F C127 87-010-759-080 C-CAP,U 0.1-25F

C128 87-010-759-080 C-CAP,U 0.1-25F C140 87-A11-567-080 C-CAP,S 0.01-50 K B C401 87-010-759-080 C-CAP,U 0.1-25F C402 87-010-759-080 C-CAP,U 0.1-25F C403 87-012-193-080 C-CAP,U 82P-50 CH

C404 87-012-193-080 C-CAP,U 82P-50 CH C405 87-012-286-080 C-CAP,U 0.01-25 K B C406 87-012-286-080 C-CAP,U 0.01-25 K B C407 87-012-286-080 C-CAP,U 0.01-25 K B C408 87-012-286-080 C-CAP,U 0.01-25 K B

C409 87-012-278-080 C-CAP,U 2200P-50 B C410 87-012-278-080 C-CAP,U 2200P-50 B C411 87-A12-091-080 CAP,E 10-50 SMG C412 87-A12-091-080 CAP,E 10-50 SMG C413 87-012-286-080 C-CAP,U 0.01-25 K B

C421 87-012-275-080 C-CAP,U 1200P-50 B C422 87-012-275-080 C-CAP,U 1200P-50 B C423 87-012-274-080 CHIP CAP,U 1000P-50B C424 87-012-274-080 CHIP CAP,U 1000P-50B C425 87-A12-062-080 CAP,E 100-10 SMG

C426 87-A12-062-080 CAP,E 100-10 SMG C427 87-012-188-080 C-CAP,U 47P-50 CH C428 87-012-188-080 C-CAP,U 47P-50 CH C429 87-010-956-080 CHIP-CAP,S 0.068-25B C430 87-010-956-080 CHIP-CAP,S 0.068-25B

C431 87-012-284-080 C-CAP,U 6800P-50 K B GRM C432 87-012-284-080 C-CAP,U 6800P-50 K B GRM C433 87-A12-085-080 CAP,E 0.33-50 SMG C434 87-A12-085-080 CAP,E 0.33-50 SMG C435 87-A12-062-080 CAP,E 100-10 SMG

C436 87-010-759-080 C-CAP,U 0.1-25F C437 87-010-759-080 C-CAP,U 0.1-25F C441 87-010-759-080 C-CAP,U 0.1-25F C442 87-010-759-080 C-CAP,U 0.1-25F C443 87-010-759-080 C-CAP,U 0.1-25F

C444 87-012-197-080 C-CAP,U 150P-50 CH C445 87-A10-039-080 C-CAP,U 470P-50 J CH C452 87-A12-069-080 CAP,E 22-25 SMG C453 87-012-279-080 C-CAP,U 2700P-50 B C454 87-012-279-080 C-CAP,U 2700P-50 B

C455 87-012-279-080 C-CAP,U 2700P-50 B C456 87-012-286-080 C-CAP,U 0.01-25 C457 87-A12-361-080 CAP,M 5600P-100 J CP C460 87-010-759-080 C-CAP,U 0.1-25F C461 87-012-158-080 C-CAP,S 390P-50 CH

C462 87-012-158-080 C-CAP,S 390P-50 CH C470 87-A10-039-080 C-CAP,U 470P-50 J CH C605 87-012-275-080 C-CAP,U 1200P-50 B C606 87-012-275-080 C-CAP,U 1200P-50 B C609 87-010-785-080 C-CAP,U 0.015-25 K B GRM

NO.

 6 

PART NO. DESCRIPTIONREF. NO. KANRI

DESCRIPTIONREF. NO. KANRI

NO.

C610 87-010-785-080 C-CAP,U 0.015-25 K B GRM C611 87-A12-084-080 CAP,E 0.22-50 SMG C612 87-A12-084-080 CAP,E 0.22-50 SMG C613 87-A12-084-080 CAP,E 0.22-50 SMG C614 87-A12-084-080 CAP,E 0.22-50 SMG

C615 87-012-172-080 C-CAP,U 10P-50 D CH C616 87-A12-063-080 CAP,E 220-10 SMG C617 87-016-459-080 CAP,E 470-10 SMG C669 87-012-195-080 C-CAP,U 100P-50CH C670 87-012-195-080 C-CAP,U 100P-50CH

C671 87-A10-260-080 C-CAP,U 0.1-16 K B C672 87-A10-260-080 C-CAP,U 0.1-16 K B C677 87-A10-260-080 C-CAP,U 0.1-16 K B C771 87-A12-062-080 CAP,E 100-10 SMG C772 87-012-286-080 C-CAP,U 0.01-25 K B

C782 87-012-286-080 C-CAP,U 0.01-25 K B C783 87-012-286-080 C-CAP,U 0.01-25 K B C784 87-012-286-080 C-CAP,U 0.01-25 K B C785 87-012-286-080 C-CAP,U 0.01-25 K B C786 87-012-286-080 C-CAP,U 0.01-25 K B

C788 87-012-167-080 C-CAP,U 5P-50 CH C789 87-A10-801-080 C-CAP,S 0.022-16 J B CM C790 87-A10-801-080 C-CAP,S 0.022-16 J B CM C791 87-010-759-080 C-CAP,U 0.1-25F C792 87-012-286-080 C-CAP,U 0.01-25 K B

C793 87-A12-090-080 CAP,E 4.7-50 SMG C794 87-012-188-080 C-CAP,U 47P-50 J CH C795 87-012-286-080 C-CAP,U 0.01-25 K B C796 87-012-286-080 C-CAP,U 0.01-25 K B C797 87-A12-091-080 CAP,E 10-50 SMG

C798 87-012-286-080 C-CAP,U 0.01-25 K B C799 87-A12-093-080 CAP,E 33-50 SMG C800 87-010-829-080 C-CAP,U 0.047-16 Z F C801 87-A12-089-080 CAP,E 3.3-50 SMG C802 87-010-829-080 C-CAP,U 0.047-16 Z F

C803 87-010-787-080 C-CAP,U 0.022-25 Z F C804 87-A12-062-080 CAP,E 100-10 SMG C807 87-A12-086-080 CAP,E 0.47-50 SMG C808 87-A12-087-080 CAP,E 1-50 SMG C809 87-A12-087-080 CAP,E 1-50 SMG

C810 87-010-759-080 C-CAP,U 0.1-25F C814 87-012-286-080 C-CAP,U 0.01-25 K B C815 87-A12-086-080 CAP,E 0.47-50 SMG C816 87-A12-086-080 CAP,E 0.47-50 SMG C821 87-A12-091-080 CAP,E 10-50 SMG

C823 87-010-177-080 C-CAP,S 820P-50 SL C824 87-A12-090-080 CAP,E 4.7-50 SMG C825 87-010-596-080 C-CAP,S 0.047-16 C836 87-012-286-080 C-CAP,U 0.01-25 C837 87-012-286-080 C-CAP,U 0.01-25

C842 87-012-286-080 C-CAP,U 0.01-25 C843 87-010-197-080 C-CAP,S 0.01-25 KB C2012 C844 87-012-286-080 C-CAP,U 0.01-25 C845 87-010-197-080 C-CAP,S 0.01-25 KB C2012 C846 87-010-197-080 C-CAP,S 0.01-25 KB C2012

C847 87-010-197-080 C-CAP,S 0.01-25 KB C2012 C848 87-010-197-080 C-CAP,S 0.01-25 KB C2012 C849 87-010-197-080 C-CAP,S 0.01-25 KB C2012 C850 87-A12-071-080 CAP,E 47-25 SMG C851 87-012-286-080 C-CAP,U 0.01-25

C852 87-012-286-080 C-CAP,U 0.01-25 C853 87-012-286-080 C-CAP,U 0.01-25 C858 87-010-759-080 C-CAP,U 0.1-25F C859 87-010-759-080 C-CAP,U 0.1-25F C860 87-012-286-080 C-CAP,U 0.01-25

C902 87-018-147-080 CAP,TC-U 10P-50 CH C908 87-012-174-080 C-CAP,U 12P-50 J CH C909 87-012-349-080 C-CAP,S 1000P-50 CH C911 87-012-170-080 C-CAP,U 8P-50 CH C912 87-012-195-080 C-CAP,U 100P-50CH

PART NO.

NO.

C913 87-012-286-080 C-CAP,U 0.01-25 C914 87-012-286-080 C-CAP,U 0.01-25 C915 87-012-286-080 C-CAP,U 0.01-25 C918 87-012-165-080 C-CAP,U 3P-50 CH C920 87-012-180-080 C-CAP,U 22P-50 CH

C921 87-012-186-080 C-CAP,U 39P-50 CH C922 87-012-174-080 C-CAP,U 12P-50 J CH C923 87-A10-039-080 C-CAP,U 470P-50 J CH C924 87-012-174-080 C-CAP,U 12P-50 J CH C927 87-012-195-080 C-CAP,U 100P-50CH

C961 87-012-170-080 C-CAP,U 8P-50 CH C962 87-A12-087-080 CAP,E 1-50 SMG C971 87-A12-067-080 CAP,E 330-16 SMG C972 87-A12-090-080 CAP,E 4.7-50 SMG C973 87-012-286-080 C-CAP,U 0.01-25 K B

C974 87-012-286-080 C-CAP,U 0.01-25 K B C979 87-012-195-080 C-CAP,U 100P-50CH C981 87-A12-071-080 CAP,E 47-25 SMG C982 87-010-759-080 C-CAP,U 0.1-25F C983 87-012-286-080 C-CAP,U 0.01-25 K B

C984 87-012-286-080 C-CAP,U 0.01-25 K B C987 87-012-286-080 C-CAP,U 0.01-25 K B C990 87-012-195-080 C-CAP,U 100P-50CH C991 87-012-176-080 C-CAP,U 15P-50J CH C992 87-012-176-080 C-CAP,U 15P-50J CH

C993 87-012-274-080 CHIP CAP,U 1000P-50B C994 87-012-195-080 C-CAP,U 100P-50CH C995 87-012-274-080 CHIP CAP,U 1000P-50B C996 87-012-195-080 C-CAP,U 100P-50CH C997 87-010-759-080 C-CAP,U 0.1-25F

C998 87-A12-071-080 CAP,E 47-25 SMG C999 87-A11-155-080 CAP,TC U 0.01-16 Z F CF831 87-008-261-010 FILTER,CF SFE10.7MA5 CF832 87-008-261-010 FILTER,CF SFE10.7MA5 CN81 87-A60-109-010 CONN,2P V S2M-2W

CN351 87-A60-625-010 CONN,8P V 2MM JMT CN401 87-A60-620-010 CONN,3P V 2MM JMT CN603 87-099-196-010 CONN,8P V BLK 6216 CNA351 8B-NFC-634-010 CONN ASSY,8P RPB CNA401 8B-NFC-633-010 CONN ASSY,3P(PH)

D902 87-A40-916-040 C-VARI-CAP,HVC202A D903 87-A40-916-040 C-VARI-CAP,HVC202A

F101 87-A91-212-010 FUSE,1A 250V T 50T

FB101 87-A90-457-010 F-BEAD,15-25-15 E251 FB602 87-008-372-080 FLTR,EMI BL01 RN1

FB603 87-A92-284-010 F-BEAD,E3407MFT2

FC101 87-033-213-080 FUSE CLAMP,PFC5000

FC102 87-033-213-080 FUSE CLAMP,PFC5000 FFC603 88-908-251-110 FF-CABLE,8P 250MM J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC

J103 87-A61-452-010 TERMINAL,SP 4P(MSC) J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02 JR621 87-010-598-080 C-CAP,S 0.068-16VRK JR622 87-010-598-080 C-CAP,S 0.068-16VRK

JW1 87-A91-941-080 PROTECTOR,3A 20P 60V

JW2 87-A91-941-080 PROTECTOR,3A 20P 60V JW14 87-008-474-010 F-BEAD,BL02RN1-R62T2 EMI JW601 87-008-474-010 F-BEAD,BL02RN1-R62T2 EMI JW621 87-008-372-010 FLTR,EMIBL01 RN1

L101 87-A50-610-010 COIL,1UH K(MDEC) L102 87-A50-610-010 COIL,1UH K(MDEC) L451 87-007-342-010 COIL,OSC 85KHZ BIAS L801 87-A50-608-010 COIL,FM DET-N(TOK) L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)

L811 87-005-847-080 COIL,2.2UH(CECS) L832 87-005-847-080 COIL,2.2UH K CECS L903 88-ZA1-602-110 COIL,FM-RF-U2 2G L904 88-ZA1-601-010 COIL,FM-RF-U1 2G L906 87-005-847-080 COIL,2.2UH(CECS)

 7 

PART NO. DESCRIPTIONREF. NO. KANRI

DESCRIPTIONREF. NO. KANRI

NO.

L907 8A-NEC-611-010 COIL,FM OSC U 2G L908 88-ZA1-624-010 COIL,FM IFT 7-6.2(COILS) L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)

PT101 8B-NHC-609-010 PT,BNH-C H R129 87-A00-258-080 RES,M/F 0.22-1W J

R130 87-A00-258-080 RES,M/F 0.22-1W J R790 87-012-286-080 C-CAP,U 0.01-25 RY101 87-A91-339-010 RELAY,AC DC12V G5PA-2

S1 87-A90-165-010 SW,SL 1-2-3 SWS2301

T101 87-A60-317-010 TERMINAL,1P MSC

T102 87-A60-317-010 TERMINAL,1P MSC X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST

FRONT C.B

C271 87-012-282-080 C-CAP,U 4700P-50 K B C272 87-010-112-040 CAP,E 100-16 C273 87-010-545-040 CAP,E 0.22-50 SME C274 87-012-195-080 C-CAP,U 100P-50 J CH C275 87-010-545-040 CAP,E 0.22-50 SME

C276 87-A10-260-080 C-CAP,U 0.1-16 K B C277 87-010-405-040 CAP,E 10-50 C278 87-012-195-080 C-CAP,U 100P-50 J CH C279 87-010-405-040 CAP,E 10-50 C280 87-010-759-080 C-CAP,U 0.1-25F

C281 87-010-177-080 C-CAP,S 820P-50 SL C282 87-010-177-080 C-CAP,S 820P-50 SL C390 87-010-384-040 CAP,E 100-25 SME C500 87-010-759-080 C-CAP,U 0.1-25F C505 87-010-829-080 C-CAP,U 0.047-16

C506 87-010-263-040 CAP,E 100-10 C507 87-A12-078-040 CAP,E 47-35 SMG C508 87-010-192-080 C-CAP,S 0.022-50 F C509 87-010-404-040 CAP,E 4.7-50 SME C510 87-010-404-040 CAP,E 4.7-50 SME

C511 87-010-401-040 CAP,E 1-50 SME C512 87-010-759-080 C-CAP,U 0.1-25F C513 87-010-759-080 C-CAP,U 0.1-25F C516 87-010-831-080 C-CAP,U 0.1-16F C517 87-010-831-080 C-CAP,U 0.1-16F

C518 87-012-274-080 CHIP CAP,U 1000P-50B C519 87-012-336-080 C-CAP,U 330P-50 J SL C520 87-012-282-080 C-CAP,U 4700P-50 K B C521 87-010-829-080 C-CAP,U 0.047-16 Z F C522 87-016-459-040 CAP,E 470-10 SMG

C523 87-010-248-040 CAP,E 220-10 SME C524 87-010-787-080 C-CAP,U 0.022-25 K B C525 87-010-071-040 CAP,E 1-50 M 5L SRE C526 87-010-405-040 CAP,E 10-50 C527 87-A10-039-080 C-CAP,U 470P-50 J CH

PART NO.

NO.

C528 87-010-263-040 CAP,E 100-10 C530 87-012-195-080 C-CAP,U 100P-50CH C531 87-012-195-080 C-CAP,U 100P-50CH C532 87-012-195-080 C-CAP,U 100P-50CH C533 87-012-195-080 C-CAP,U 100P-50CH

C534 87-012-195-080 C-CAP,U 100P-50CH C535 87-012-195-080 C-CAP,U 100P-50CH C536 87-012-195-080 C-CAP,U 100P-50CH C537 87-012-195-080 C-CAP,U 100P-50CH C538 87-012-195-080 C-CAP,U 100P-50CH

C539 87-012-195-080 C-CAP,U 100P-50CH C540 87-010-759-080 C-CAP,U 0.1-25F C546 87-010-759-080 C-CAP,U 0.1-25F C555 87-012-172-080 C-CAP,U 10P-50 D CH C556 87-012-198-080 C-CAP,U 180P-50 J CH

C557 87-010-831-080 C-CAP,U 0.1-16F C558 87-010-831-080 C-CAP,U 0.1-16F C560 87-012-286-080 C-CAP,U 0.01-25 K B CN501 87-A60-673-010 CONN,9P H 2MM JMT CN504 87-099-196-010 CONN,8P V BLK 6216

EMI271 87-008-372-080 FLTR,EMI BL01 RN1 FB504 87-A92-284-010 F-BEAD,E3407MFT2 FFC504 88-908-341-110 FF-CABLE,8P 1.25 34 FL501 8B-NFC-601-010 FL,HNA-10SS18T J271 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM

L501 87-A50-655-010 COIL,CLK 4.19MHZ (TOKO)7KLY S301 87-A91-024-180 SW,TACT KSHG611BT S302 87-A91-024-180 SW,TACT KSHG611BT S303 87-A91-024-180 SW,TACT KSHG611BT S304 87-A91-024-180 SW,TACT KSHG611BT

S305 87-A91-024-180 SW,TACT KSHG611BT S306 87-A91-024-180 SW,TACT KSHG611BT S307 87-A91-024-180 SW,TACT KSHG611BT S308 87-A91-024-180 SW,TACT KSHG611BT S309 87-A91-024-180 SW,TACT KSHG611BT

S310 87-A91-024-180 SW,TACT KSHG611BT S311 87-A91-024-180 SW,TACT KSHG611BT S312 87-A91-024-180 SW,TACT KSHG611BT S313 87-A91-024-180 SW,TACT KSHG611BT S314 87-A91-024-180 SW,TACT KSHG611BT

S315 87-A91-024-180 SW,TACT KSHG611BT S316 87-A91-024-180 SW,TACT KSHG611BT SFR391 87-024-431-080 SFR,3.3K H RH063MC VR271 86-NFA-607-010 VR,RTRY 10K15AX1 1 V XV0121PVN

 8 

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

Resistor Code

Chip resistor

Wattage Type Tolerance 1/16W 1005 5% CJ

1/16W 1/10W

1/8W

1608 2125

3216

5% 5%

TRANSISTOR ILLUSTRATION

Symbol

CJ CJ

Figure

Value of resistor

Form

Dimensions (mm)

0.55

Resistor Code

108 118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45 2 1.25 0.45

3.2

1.6

: A : A

E C B

2SA1980G 2SC2240(GR/BL) CSC4115BC KTC3198GR

2SA1235F 2SC2714O 2SC3052F 2SC5345SF/S(O) KRA107S KRC104S SBT5401F SBT5551F

E C B

2SA1981Y STC250

2SK360E

B C E

2SB1342

B C E

KT A1046Y

2SD1933

S D G

2SJ460 2SK2541

– 9 –

+ 19 hidden pages