PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
3
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
1Remove the AC power cord.
2Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4Contact the same end of the discharging resistor as step 3
to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V)Discharging
(C101, 102)resistor (Ω)
25-48100387-A00-247-090
49-140220587-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W)Parts number
MAIN C.B
D101
3
C101C102
22
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
1Turn on the AC main power.
2Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
4
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
FRONT C.B
18
MICROCOMPUTER
15
C113
C113
15
18
VSS
VDD
MICROCOMPUTER
FRONT C.B
Short with tweezers.
Fig-2-2
2Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
C000387-012-368-080C-CAP,S 0.1-50 Z F
C000487-012-368-080C-CAP,S 0.1-50 Z F
C002187-016-658-000CAP,E 4700-35 M SMG
C002287-016-658-000CAP,E 4700-35 M SMG
C002587-010-405-080CAP,E 10-50 M 11L SME
C002687-010-406-080CAP,E 22-50 M 11L SME
C002787-010-405-080CAP,E 10-50 M 11L SME
C002887-010-406-080CAP,E 22-50 M 11L SME
C003187-010-263-080CAP,E 100-10 M 11L SME
C003287-010-197-080C-CAP,S 0.01-25 K B C2012
C003387-010-263-080CAP,E 100-10 M 11L SME
C003487-010-384-080CAP,E 100-25 M 11L SME
C003587-010-406-080CAP,E 22-50 M 11L SME
C003687-010-381-080CAP,E 330-16 M SME
C003887-010-394-080CAP,E 220-35 M SME
C003987-010-394-080CAP,E 220-35 M SME
C004087-010-197-080C-CAP,S 0.01-25 K B C2012
C006087-010-403-080CAP,E 3.3-50 M 11L SME
C008087-016-279-080CAP,E 1-50 M BP SME
C008187-010-260-080CAP,E 47-25 M 11L SME
C008287-010-260-080CAP,E 47-25 M 11L SME
C011587-010-403-080CAP,E 3.3-50 M 11L SME
C011687-010-403-080CAP,E 3.3-50 M 11L SME
C015287-010-260-080CAP,E 47-25 M 11L SME
C017187-012-368-080C-CAP,S 0.1-50 Z F
C017287-012-368-080C-CAP,S 0.1-50 Z F
C017387-012-368-080C-CAP,S 0.1-50 Z F
C017487-012-368-080C-CAP,S 0.1-50 Z F
C030187-010-318-080C-CAP,S 47P-50 J CH GRM
C030287-010-318-080C-CAP,S 47P-50 J CH GRM
C030987-010-196-080C-CAP,S 0.1-25 Z F C2012
C031087-010-196-080C-CAP,S 0.1-25 Z F C2012
C031187-010-198-080C-CAP,S 0.022-25 K B C2012
C031287-010-198-080C-CAP,S 0.022-25 K B C2012
C031387-010-179-080C-CAP,S 1200P-50 K B GRM
C031487-010-179-080C-CAP,S 1200P-50 K B GRM
C031587-010-179-080C-CAP,S 1200P-50 K B GRM
C031687-010-179-080C-CAP,S 1200P-50 K B GRM
C032187-012-142-080C-CAP,S 0.33-16 Z F GRM
C032287-012-142-080C-CAP,S 0.33-16 Z F GRM
C032487-010-260-080CAP,E 47-25 M 11L SME
C032587-010-370-080CAP,E 330-6.3 M SME
C032787-010-404-080CAP,E 4.7-50 M 11L SME
C032887-010-404-080CAP,E 4.7-50 M 11L SME
C033287-010-196-080C-CAP,S 0.1-25 Z F C2012
C033587-010-401-080CAP,E 1-50 M 11L SME
C033687-010-401-080CAP,E 1-50 M 11L SME
C033787-010-196-080C-CAP,S 0.1-25 Z F C2012
C033987-010-196-080C-CAP,S 0.1-25 Z F C2012
C034087-010-196-080C-CAP,S 0.1-25 Z F C2012
C035187-012-140-080C-CAP,S 470P-50 J CH
C035287-012-140-080C-CAP,S 470P-50 J CH
C035487-010-175-080C-CAP,S 560P-50 J SL
C035587-010-178-080C-CAP,S 1000P-50 K B C2012
C035687-010-260-080CAP,E 47-25 M 11L SME
C035787-010-197-080C-CAP,S 0.01-25 K B C2012
C035887-010-183-080C-CAP,S 2700P-50 K B GRM
C035987-010-183-080C-CAP,S 2700P-50 K B GRM
C036087-010-183-080C-CAP,S 2700P-50 K B GRM
C036387-A10-292-080CAP,M 5600P-50 J
C037087-010-196-080C-CAP,S 0.1-25 Z F C2012
C037387-016-083-080C-CAP,S 0.15-16 K R
C037487-016-083-080C-CAP,S 0.15-16 K R
NO.
6
REF. NOPART NO.KANRIDESCRIPTION
C037887-010-196-080C-CAP,S 0.1-25 Z F C2012
C037987-010-382-080CAP,E 22-25 M 11L SME
C038087-010-382-080CAP,E 22-25 M 11L SME
C038187-010-197-080C-CAP,S 0.01-25 K B C2012
C038287-010-312-080C-CAP,S 15P-50 J CH GRM
C038387-010-197-080C-CAP,S 0.01-25 K B C2012
C038487-010-402-080CAP,E 2.2-50 M 11L SME
C038687-010-196-080C-CAP,S 0.1-25 Z F C2012
C038787-012-145-080C-CAP,S 270P-50 J CH GRM
C038887-012-156-080C-CAP,S 220P-50 J CH GRM
C040287-010-176-080C-CAP,S 680P-50 J SL
C040387-010-958-080C-CAP,S 0.01-25 J B
C040487-010-958-080C-CAP,S 0.01-25 J B
C040587-010-958-080C-CAP,S 0.01-25 J B
C040687-010-958-080C-CAP,S 0.01-25 J B
C040787-010-401-080CAP,E 1-50 M 11L SME
C040887-010-401-080CAP,E 1-50 M 11L SME
C040987-010-196-080C-CAP,S 0.1-25 Z F C2012
C041087-010-112-080CAP,E 100-16 M 11L SME
C041187-010-400-080CAP,E 0.47-50 M 11L SME
C041287-010-400-080CAP,E 0.47-50 M 11L SME
C041387-010-401-080CAP,E 1-50 M 11L SME
C041487-010-401-080CAP,E 1-50 M 11L SME
C041587-010-546-080CAP,E 0.33-50 M 11L SME
C041687-010-546-080CAP,E 0.33-50 M 11L SME
C041787-010-221-080CAP,E 470-10 M SME
C041887-A10-891-080CAP,E 4.7-25 SME(K)
C041987-A10-800-080C-CAP,S 6800P-16 J B CM
C042087-010-374-080CAP,E 47-10 M 11L SME
C042187-010-196-080C-CAP,S 0.1-25 Z F C2012
C042287-A10-804-080C-CAP,S 0.1-25 J B
C042487-010-374-080CAP,E 47-10 M 11L SME
C042587-010-196-080C-CAP,S 0.1-25 Z F C2012
C042987-010-545-080CAP,E 0.22-50 M 11L SME
C043087-012-142-080C-CAP,S 0.33-16 Z F GRM
C043187-010-971-080C-CAP,S 4700P-50 J B
C043287-012-349-080C-CAP,S 1000P-50 J CH GRM
C043387-A11-183-080C-CAP,S 0.12-16 J B
C043487-A11-182-080C-CAP,S 0.27-16 J B
C043587-A11-182-080C-CAP,S 0.27-16 J B
C043687-A11-183-080C-CAP,S 0.12-16 J B
C043787-010-971-080C-CAP,S 4700P-50 J B
C043887-012-349-080C-CAP,S 1000P-50 J CH GRM
C043987-010-805-080C-CAP,S 1-16 Z F
C044087-010-401-080CAP,E 1-50 M 11L SME
C044187-A10-799-080C-CAP,S 5600P-16 J B CM
C044287-A10-802-080C-CAP,S 0.047-16 J B CM
C044387-A10-229-080C-CAP,S 0.68-10 K W5R
C044487-012-393-080C-CAP,S 0.22-16 K W5R CM/CB
C044587-012-393-080C-CAP,S 0.22-16 K W5R CM/CB
C044687-010-404-080CAP,E 4.7-50 M 11L SME
C044787-010-404-080CAP,E 4.7-50 M 11L SME
C044887-012-393-080C-CAP,S 0.22-16 K W5R CM/CB
C044987-012-393-080C-CAP,S 0.22-16 K W5R CM/CB
C045087-016-081-080C-CAP,S 0.1-16 K R GRM
C045187-A10-802-080C-CAP,S 0.047-16 J B CM
C045287-A10-802-080C-CAP,S 0.047-16 J B CM
C045387-016-081-080C-CAP,S 0.1-16 K R GRM
C045487-016-081-080C-CAP,S 0.1-16 K R GRM
C045587-A10-801-080C-CAP,S 0.022-16 J B CM
C045687-A10-801-080C-CAP,S 0.022-16 J B CM
C045787-016-081-080C-CAP,S 0.1-16 K R GRM
C046187-010-196-080C-CAP,S 0.1-25 Z F C2012
C046387-010-196-080C-CAP,S 0.1-25 Z F C2012
C046587-016-552-080C-CAP,S 0.082-16 K B C2012
NO.
REF. NOPART NO.KANRIDESCRIPTION
C046687-010-194-080C-CAP,S 0.047-25 Z F
C046787-A10-201-080C-CAP,S 0.33-16 K B
C046887-A10-060-080C-CAP,S 0.18-16 K B
C047887-010-401-080CAP,E 1-50 M 11L SME
C047987-010-179-080C-CAP,S 1200P-50 K B GRM
C048087-010-179-080C-CAP,S 1200P-50 K B GRM
C048187-010-179-080C-CAP,S 1200P-50 K B GRM
C048287-010-179-080C-CAP,S 1200P-50 K B GRM
C048387-010-401-080CAP,E 1-50 M 11L SME
C048987-010-402-080CAP,E 2.2-50 M 11L SME
C049187-010-402-080CAP,E 2.2-50 M 11L SME
C049287-010-402-080CAP,E 2.2-50 M 11L SME
C053187-010-405-080CAP,E 10-50 M 11L SME
C053387-010-196-080C-CAP,S 0.1-25 Z F C2012
C053487-012-156-080C-CAP,S 220P-50 J CH GRM
C053587-010-178-080C-CAP,S 1000P-50 K B C2012
C053687-010-196-080C-CAP,S 0.1-25 Z F C2012
C054187-010-178-080C-CAP,S 1000P-50 K B C2012
C060987-010-181-080C-CAP,S 1800P-50 K B GRM
C061087-010-181-080C-CAP,S 1800P-50 K B GRM
C061187-010-598-080C-CAP,S 0.068-16 K R GRM
C061287-016-369-080C-CAP,S 0.033-25 K B GRM
C061387-010-197-080C-CAP,S 0.01-25 K B C2012
C061487-016-669-080C-CAP,S 0.1-25 K B
C061687-010-184-080C-CAP,S 3300P-50 K B C2012
C061787-012-369-080C-CAP,S 0.047-50 Z F
C061887-010-401-080CAP,E 1-50 M 11L SME
C061987-010-263-080CAP,E 100-10 M 11L SME
C062087-016-669-080C-CAP,S 0.1-25 K B
C062187-010-197-080C-CAP,S 0.01-25 K B C2012
C062387-010-401-080CAP,E 1-50 M 11L SME
C062487-010-401-080CAP,E 1-50 M 11L SME
C062687-A10-354-080C-CAP,S 0.047-50 K B
C062787-010-400-080CAP,E 0.47-50 M 11L SME
C062887-010-400-080CAP,E 0.47-50 M 11L SME
C062987-A10-354-080C-CAP,S 0.047-50 K B
C063087-010-383-080CAP,E 33-25 M 11L SME
C063187-010-185-080C-CAP,S 3900P-50 K B
C063287-010-185-080C-CAP,S 3900P-50 K B
C063487-010-196-080C-CAP,S 0.1-25 Z F C2012
C063587-A10-307-080CAP,M 0.1-50 J
C063687-A10-307-080CAP,M 0.1-50 J
C063787-A10-307-080CAP,M 0.1-50 J
C063887-A10-307-080CAP,M 0.1-50 J
C063987-010-405-080CAP,E 10-50 M 11L SME
C064187-010-401-080CAP,E 1-50 M 11L SME
C064287-010-401-080CAP,E 1-50 M 11L SME
C064387-010-196-080C-CAP,S 0.1-25 Z F C2012
C064487-010-401-080CAP,E 1-50 M 11L SME
C067187-010-322-080C-CAP,S 100P-50 J CH GRM
C067287-010-322-080C-CAP,S 100P-50 J CH GRM
C067387-010-197-080C-CAP,S 0.01-25 K B C2012
C067987-010-196-080C-CAP,S 0.1-25 Z F C2012
C068087-010-197-080C-CAP,S 0.01-25 K B C2012
C068287-010-196-080C-CAP,S 0.1-25 Z F C2012
C077187-010-263-080CAP,E 100-10 M 11L SME
C077287-010-197-080C-CAP,S 0.01-25 K B C2012
C077387-010-184-080C-CAP,S 3300P-50 K B C2012
C077487-010-184-080C-CAP,S 3300P-50 K B C2012
C077987-010-426-080C-CAP,S 0.012-25 K B
C078087-010-426-080C-CAP,S 0.012-25 K B
C078287-010-197-080C-CAP,S 0.01-25 K B C2012
C078387-010-197-080C-CAP,S 0.01-25 K B C2012
C078487-010-197-080C-CAP,S 0.01-25 K B C2012
C078587-010-197-080C-CAP,S 0.01-25 K B C2012
C078687-010-197-080C-CAP,S 0.01-25 K B C2012
C078887-010-149-080C-CAP,S 5P-50 C CH GRM
C078987-A10-592-080C-CAP,S 0.015-50 J B
C079087-A10-592-080C-CAP,S 0.015-50 J B
C079187-010-196-080C-CAP,S 0.1-25 Z F C2012
NO.
7
REF. NOPART NO.KANRIDESCRIPTION
NO.
C079287-010-197-080C-CAP,S 0.01-25 K B C2012
C079387-010-404-080CAP,E 4.7-50 M 11L SME
C079587-010-197-080C-CAP,S 0.01-25 K B C2012
C079687-010-197-080C-CAP,S 0.01-25 K B C2012
C079787-010-405-080CAP,E 10-50 M 11L SME
C079887-010-197-080C-CAP,S 0.01-25 K B C2012
C079987-010-407-080CAP,E 33-50 M 11L SME
C080087-012-369-080C-CAP,S 0.047-50 Z F
C080187-010-403-080CAP,E 3.3-50 M 11L SME
C080287-012-369-080C-CAP,S 0.047-50 Z F
C080387-010-198-080C-CAP,S 0.022-25 K B C2012
C080487-010-263-080CAP,E 100-10 M 11L SME
C080787-010-400-080CAP,E 0.47-50 M 11L SME
C080887-010-401-080CAP,E 1-50 M 11L SME
C080987-010-401-080CAP,E 1-50 M 11L SME
C081087-010-196-080C-CAP,S 0.1-25 Z F C2012
C081187-010-403-080CAP,E 3.3-50 M 11L SME
C081287-010-403-080CAP,E 3.3-50 M 11L SME
C081487-010-197-080C-CAP,S 0.01-25 K B C2012
C081587-010-403-080CAP,E 3.3-50 M 11L SME
C081687-010-403-080CAP,E 3.3-50 M 11L SME
C081987-010-179-080C-CAP,S 1200P-50 K B GRM
C082087-010-179-080C-CAP,S 1200P-50 K B GRM
C082187-010-405-080CAP,E 10-50 M 11L SME
C082387-010-177-080C-CAP,S 820P-50 J SL C2012
C082487-010-405-080CAP,E 10-50 M 11L SME
C082587-010-596-080C-CAP,S 0.047-16 K R C2012
C084287-010-197-080C-CAP,S 0.01-25 K B C2012
C084387-010-190-080C-CAP,S 0.01-50 Z F C2012
C084487-010-197-080C-CAP,S 0.01-25 K B C2012
C084587-010-190-080C-CAP,S 0.01-50 Z F C2012
C084687-010-190-080C-CAP,S 0.01-50 Z F C2012
C084787-010-190-080C-CAP,S 0.01-50 Z F C2012
C084887-010-190-080C-CAP,S 0.01-50 Z F C2012
C084987-010-190-080C-CAP,S 0.01-50 Z F C2012
C085087-010-260-080CAP,E 47-25 M 11L SME
C085187-010-197-080C-CAP,S 0.01-25 K B C2012
C085287-010-197-080C-CAP,S 0.01-25 K B C2012
C085387-010-197-080C-CAP,S 0.01-25 K B C2012
C085887-010-196-080C-CAP,S 0.1-25 Z F C2012
C085987-010-196-080C-CAP,S 0.1-25 Z F C2012
C086087-010-197-080C-CAP,S 0.01-25 K B C2012
C095987-010-196-080C-CAP,S 0.1-25 Z F C2012
C096087-010-196-080C-CAP,S 0.1-25 Z F C2012
C096187-010-152-080C-CAP,S 8P-50 D CH GRM
C096387-015-785-080C-CAP, 0.1-25 Z F C3216
C097187-010-381-080CAP,E 330-16 M SME
C097287-010-404-080CAP,E 4.7-50 M 11L SME
C097387-010-197-080C-CAP,S 0.01-25 K B C2012
C097487-010-197-080C-CAP,S 0.01-25 K B C2012
C097987-010-322-080C-CAP,S 100P-50 J CH GRM
C098187-010-260-080CAP,E 47-25 M 11L SME
C098287-010-196-080C-CAP,S 0.1-25 Z F C2012
C098387-010-197-080C-CAP,S 0.01-25 K B C2012
C098487-010-197-080C-CAP,S 0.01-25 K B C2012
C098787-010-197-080C-CAP,S 0.01-25 K B C2012
C099187-010-312-080C-CAP,S 15P-50 J CH GRM
C099287-010-312-080C-CAP,S 15P-50 J CH GRM
C099387-010-178-080C-CAP,S 1000P-50 K B C2012
C099587-010-178-080C-CAP,S 1000P-50 K B C2012
C099787-010-196-080C-CAP,S 0.1-25 Z F C2012
C099887-010-260-080CAP,E 47-25 M 11L SME
C099987-A11-155-080CAP,TC U 0.01-16 Z F
CF083187-008-261-010FLTR,CF SFE10.7MA5
CF083287-008-261-010FLTR,CF SFE10.7MA5
CN000187-A60-996-010CONN,13P V BLK TAC-L13X-A3
CN009187-A60-109-010CONN,2P V S2M-2W
CN010187-A60-996-010CONN,13P V BLK TAC-L13X-A3
CN030187-A60-620-010CONN,3P V 2MM JMT
CN035187-A60-625-010CONN,8P V 2MM JMT
REF. NOPART NO.KANRIDESCRIPTION
NO.
CN060187-099-719-010CONN,30P H BLK TYK-B(X)
CN060287-099-194-010CONN,6P V BLK 6216
CNA0001 8A-NF8-653-010CONN ASSY,9P TID-A(480)
CNA0002 8A-NF6-630-010CONN ASSY,3P (VM) ANF-6
FFC0602 85-NF5-617-010CABLE,FFC 6P-1.25
FFE0831 A8-8ZA-190-0308ZA-1 FEUNM
J010187-A60-483-010JACK,DIA6.3 BLK ST W/S KM
J010287-A60-238-010TERMINAL,SP 4P (MSC)
J043187-A60-746-010JACK,PIN 6P R/W,R/W, O/B
J060187-A60-885-010JACK,PIN 6P R/W MSC
L082287-A50-209-010COIL,1POLE MPX(MIT)A
L083287-005-847-080COIL,2.2UH K CECS
L09518A-NF8-667-010COIL,AM PACK 4(TOK)
R016187-A00-441-050RES,270-1/2W J RP
R016287-A00-441-050RES,270-1/2W J RP
R016387-A00-441-050RES,270-1/2W J RP
R016487-A00-441-050RES,270-1/2W J RP
R040787-022-214-080C-RES,S 100K-1/10W F
R044587-010-195-080C-CAP,S 0.068-25 Z F C2012
R079087-010-197-080C-CAP,S 0.01-25 K B C2012
C010187-010-190-080C-CAP,S 0.01-50 Z F C2012
C010287-010-322-080C-CAP,S 100P-50 J CH GRM
C010387-010-312-080C-CAP,S 15P-50 J CH GRM
C010487-012-157-080C-CAP,S 330P-50 J CH GRM
C010587-010-406-040CAP,E 22-50 M 11L SME
C010687-010-493-040CAP,E 0.47-50 M 5L SRE
C010787-A10-189-040CAP,E 220-10 M 5L
C010887-A10-189-040CAP,E 220-10 M 5L
C010987-010-196-080C-CAP,S 0.1-25 Z F C2012
C011087-010-178-080C-CAP,S 1000P-50 K B C2012
C011287-012-368-080C-CAP,S 0.1-50 Z F
C011387-012-369-080C-CAP,S 0.047-50 Z F
C011487-010-196-080C-CAP,S 0.1-25 Z F C2012
C011587-010-196-080C-CAP,S 0.1-25 Z F C2012
C011687-010-196-080C-CAP,S 0.1-25 Z F C2012
C011887-012-145-080C-CAP,S 270P-50 J CH GRM
C011987-010-498-040CAP,E 10-16 M 5L SRE
C012087-010-196-080C-CAP,S 0.1-25 Z F C2012
C012187-010-196-080C-CAP,S 0.1-25 Z F C2012
C012287-010-196-080C-CAP,S 0.1-25 Z F C2012
C012387-012-393-080C-CAP,S 0.22-16 K W5R CM/CB
C018187-010-322-080C-CAP,S 100P-50 J CH GRM
C018287-010-178-080C-CAP,S 1000P-50 K B C2012
C018387-012-156-080C-CAP,S 220P-50 J CH GRM
C020287-012-157-080C-CAP,S 330P-50 J CH GRM
C022187-010-421-040CAP,E 4.7-50 M 5L SRE
C022287-010-404-040CAP,E 4.7-50 M 11L SME
C022387-010-408-040CAP,E 47-50 M 11L SME
C022487-012-369-080C-CAP,S 0.047-50 Z F
C038287-010-320-080C-CAP,S 68P-50 J CH GRM
C038387-010-196-080C-CAP,S 0.1-25 Z F C2012
C038487-010-196-080C-CAP,S 0.1-25 Z F C2012
C038587-010-196-080C-CAP,S 0.1-25 Z F C2012
C038687-010-196-080C-CAP,S 0.1-25 Z F C2012
C038787-010-196-080C-CAP,S 0.1-25 Z F C2012
C040687-010-322-080C-CAP,S 100P-50 J CH GRM
C040787-010-322-080C-CAP,S 100P-50 J CH GRM
C040887-010-322-080C-CAP,S 100P-50 J CH GRM
C040987-010-196-080C-CAP,S 0.1-25 Z F C2012
C060187-010-186-080C-CAP,S 4700P-50 K B C2012
C060287-010-405-040CAP,E 10-50 M 11L SME
C060387-010-320-080C-CAP,S 68P-50 J CH GRM
C060487-010-546-040CAP,E 0.33-50 M 11L SME
C060687-010-112-040CAP,E 100-16 M 11L SME
C060787-010-196-080C-CAP,S 0.1-25 Z F C2012
C060887-010-178-080C-CAP,S 1000P-50 K B C2012
C060987-010-196-080C-CAP,S 0.1-25 Z F C2012
C062187-010-178-080C-CAP,S 1000P-50 K B C2012
C065287-010-183-080C-CAP,S 2700P-50 K B GRM
C065387-010-213-080C-CAP,S 0.015-25 K B GRM
C070187-010-260-040CAP,E 47-25 M 11L SME
CN01028A-NF7-605-010CONN ASSY,4P V 80MM
CN010487-099-017-010CONN,15P V BLK 6216
CN090187-A60-138-010CONN,13P V FE
CON0101 87-099-720-010CONN,30P BLK TYK-B(P)
FB060187-008-372-080FLTR,EMI BL01 RN1
FFC0104 88-915-111-110FF-CABLE,15P 1.25
FFC0901 85-NF5-618-010CABLE,FFC 13P-1.25
FL02018A-NF7-601-010FL,BJ754GNK
J060187-A61-242-010JACK,6.3 BLK MONO W/SW V KM
J060287-A61-242-010JACK,6.3 BLK MONO W/SW V KM
L010187-A50-333-010COIL,OSC 9.43MHZ
LED0401 87-017-733-080LED,SEL1250SMTP5 RED
LED0402 87-017-733-080LED,SEL1250SMTP5 RED
LED0403 87-017-733-080LED,SEL1250SMTP5 RED
LED0404 87-017-733-080LED,SEL1250SMTP5 RED
LED0405 87-017-733-080LED,SEL1250SMTP5 RED
LED0416 87-A40-619-080LED,SLR-56PT-TE7-W GRN
LED0417 87-A40-619-080LED,SLR-56PT-TE7-W GRN
LED0418 87-A40-619-080LED,SLR-56PT-TE7-W GRN
LED0419 87-A40-619-080LED,SLR-56PT-TE7-W GRN
LED0420 87-A40-619-080LED,SLR-56PT-TE7-W GRN
LED0421 87-A40-619-080LED,SLR-56PT-TE7-W GRN
LED0422 87-A40-317-080LED,SLR-342VCT31 RED
LED0423 87-A40-317-080LED,SLR-342VCT31 RED
C010187-010-183-080C-CAP,S 2700P-50 K B GRM
C010287-010-183-080C-CAP,S 2700P-50 K B GRM
C010387-010-546-080CAP,E 0.33-50 M 11L SME
C010487-010-546-080CAP,E 0.33-50 M 11L SME
C010587-010-186-080C-CAP,S 4700P-50 K B C2012
C010687-010-186-080C-CAP,S 4700P-50 K B C2012
C010787-010-403-080CAP,E 3.3-50 M 11L SME
C010887-010-403-080CAP,E 3.3-50 M 11L SME
C011187-012-140-080C-CAP,S 470P-50 J CH
C011287-012-140-080C-CAP,S 470P-50 J CH
C011387-010-405-080CAP,E 10-50 M 11L SME
C011487-010-405-080CAP,E 10-50 M 11L SME
C011587-016-299-080CAP,E 10-100 M SME
C011687-016-299-080CAP,E 10-100 M SME
C011987-010-197-080C-CAP,S 0.01-25 K B C2012
C012087-010-197-080C-CAP,S 0.01-25 K B C2012
C013387-010-190-080C-CAP,S 0.01-50 Z F C2012
C015387-010-188-080C-CAP,S 6800P-50 K B C2012
C020587-010-183-080C-CAP,S 2700P-50 K B GRM
C020687-010-183-080C-CAP,S 2700P-50 K B GRM
C020787-010-404-080CAP,E 4.7-50 M 11L SME
C020887-010-404-080CAP,E 4.7-50 M 11L SME
C021187-010-260-080CAP,E 47-25 M 11L SME
C021287-010-260-080CAP,E 47-25 M 11L SME
C021587-012-140-080C-CAP,S 470P-50 J CH
C021687-012-140-080C-CAP,S 470P-50 J CH
C021787-010-405-080CAP,E 10-50 M 11L SME
C021887-010-405-080CAP,E 10-50 M 11L SME
C022187-010-405-080CAP,E 10-50 M 11L SME
C022287-010-405-080CAP,E 10-50 M 11L SME
C022387-010-197-080C-CAP,S 0.01-25 K B C2012
C022487-010-197-080C-CAP,S 0.01-25 K B C2012
9
REF. NOPART NO.KANRIDESCRIPTION
NO.
C025187-010-196-080C-CAP,S 0.1-25 Z F C2012
C025287-010-196-080C-CAP,S 0.1-25 Z F C2012
C025387-010-196-080C-CAP,S 0.1-25 Z F C2012
C025487-010-196-080C-CAP,S 0.1-25 Z F C2012
C040187-010-260-080CAP,E 47-25 M 11L SME
CN010187-A61-011-010CONN,13P H BLK TAC-L13P-A3
CN010287-A61-011-010CONN,13P H BLK TAC-L13P-A3
CN010387-A60-131-010CONN,6P V FE
CNA0101 8A-NF8-656-010CONN ASSY,5P TID-A 400
CNA0103 8A-NF8-655-010CONN ASSY,7P TID-A(250)
C016087-010-186-080C-CAP,S 4700P-50 K B C2012
C016187-010-183-080C-CAP,S 2700P-50 K B GRM
C020187-010-183-080C-CAP,S 2700P-50 K B GRM
C020287-010-404-080CAP,E 4.7-50 M 11L SME
C020487-010-406-080CAP,E 22-50 M 11L SME
C020587-010-260-080CAP,E 47-25 M 11L SME
C020687-A10-946-080C-CAP,S 220P-100 J CH
C020887-010-197-080C-CAP,S 0.01-25 K B C2012
C020987-010-260-080CAP,E 47-25 M 11L SME
C021087-010-260-080CAP,E 47-25 M 11L SME
C021187-010-178-080C-CAP,S 1000P-50 K B C2012
C021287-010-178-080C-CAP,S 1000P-50 K B C2012
C025187-012-368-080C-CAP,S 0.1-50 Z F
C025287-010-196-080C-CAP,S 0.1-25 Z F C2012
C025387-010-190-080C-CAP,S 0.01-50 Z F C2012
CN010187-A61-109-010CONN,7P V TID-A
CN010487-A60-131-010CONN,6P V FE
J010287-A60-573-010JACK,PIN 1P ORN
L025187-A50-610-010COIL,1UH K(MDEC)
R021887-A00-258-080RES,M/F 0.22-1W J
TH020187-A91-042-080C-THMS,100K 55001
REF. NOPART NO.KANRIDESCRIPTION
NO.
HEAD-2 C.B
85-ZM3-602-010PWB,FLEX A
CON35187-NF6-616-010CONN ASSY,8P-RPB
PT C.B
C000187-010-387-080CAP,E 470-25 M SME
C000487-A11-148-080CAP,TC U 0.1-50 Z F
C000587-A11-148-080CAP,TC U 0.1-50 Z F
C000687-A10-627-000CAP,E 2200-50 M SMG
C000787-A10-627-000CAP,E 2200-50 M SMG
C000887-A11-148-080CAP,TC U 0.1-50 Z F
C000987-A11-148-080CAP,TC U 0.1-50 Z F
C001087-A11-148-080CAP,TC U 0.1-50 Z F
C001187-A11-148-080CAP,TC U 0.1-50 Z F
C001287-016-657-090CAP,E 3300-71 M SMG
C001387-016-657-090CAP,E 3300-71 M SMG
C001687-010-403-080CAP,E 3.3-50 M 11L SME
CN000187-A61-110-010CONN,9P V TID-A
CN000287-A61-108-010CONN,5P V TID-A
CON10587-099-756-019CONN,15P 9604 S F
SFR187-024-581-019SFR,3.3K DIA 6H
SOL182-ZM1-618-410SOL ASSY,27
SOL282-ZM1-618-410SOL ASSY,27
SW187-A90-248-019SW,MICRO ESE11SH2CXQ