Page 1
NSX-BL14
HT,G
SERVICE MANUAL
COMPACT DISC STEREO
CASSETTE RECEIVER
SYSTEM
NSX-BL14
• This Service Manual is the “Revision Publishing” and replaces “Simple
Manual” NSX-BL14(HT,G), (S/M Code No. 09-006-428-8T5).
CD
CASSEIVER
CX-NBL14 SX-NBL11
BASIC TAPE MECHANISM : ZZM-2 PR1NM
BASIC CD MECHANISM : AZG-1 ZA3RNDM
SPEAKER
REMOTE
CONTROLLER
RC-ZAS02
• If requiring information about the CD mechanism, see Service Manual
of AZG-1 (S/M Code No. 09-001-335-3NC).
S/M Code No. 09-007-428-8R4
REVISION
DATA
Page 2
SPECIFICATIONS
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) HT: 13.2 dBf
G: 16.8 dBf
Antenna terminals 75 ohms (unbalanced)
<AM/MW tuner section>
Tuning range 530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<LW tuner section><G>
Tuning range 144 kHz to 290 kHz
Usable sensitivity 1400 µV/m
Antenna Loop antenna
<SW tuner section><HT>
Tuning range 5.730 MHz to 17.900 MHz
Usable sensitivity 40 µV (IEC)
Antenna Wire antenna
<Amplifier section>
Power output Rated
HT: 17 W + 17 W (1 kHz, T.H.D. 1%,
6 ohms)
Reference: 20 W + 20 W
(1 kHz, T.H.D. 10%, 6 ohms)
G: 12 W + 12 W (1 kHz/DIN 45500,
T.H.D. 1%, 6 ohms)
Reference: 15 W + 15 W
(1 kHz/DIN 45324, T.H.D. 10%, 6 ohms)
Total harmonic distortion G: 0.1% (6 W, 1 kHz, 6 ohms,
DIN AUDIO)
HT: 0.1% (8 W, 1 kHz, 6 ohms,
DIN AUDIO)
Inputs VIDEO/AUX: 500 mV
HT: MIC 1.8 mV(10 kohms)
Outputs SPEAKERS: accept speakers of 6
ohms or more
PHONES (stereo jack) : accepts
headphones of 32 ohms or more
<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
<Speaker system>SX-NBL11
Speaker System 2 way, bass reflex (magnetic shielded
type)
Speaker units Woofer:
120 mm cone type
Tweeter:
20 mm cone type
Impedance 6 ohms
Sensitivity 87 dB/W/m
Dimensions (W x H x D) 220 x 324 x 211 mm
Weight 2.0 kg
<General>
Power requirements HT: 120 V/220-230 V/240 V AC
(switchable), 50/60 Hz
G: 230 V AC, 50 Hz
Power consumption HT: 60 W
G: 45 W
Power consumption With power-economizing
in standby mode mode off : 14 W
With power-economizing mode on :
0.9 W
Dimensions of main unit 260 x 324 x 348 mm
(W x H x D)
Weight of main unit HT: 5.0 kg
G: 4.9 kg
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz - 8000 Hz
Recording system AC bias
Heads Deck 1 : Recording/Playback head
x 1, erase head x 1
Deck 2 : Playback head x 1
• Design and specifications are subject to change without notice.
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP ASSY
P.C.B
SOLDER
– 3 –
Page 4
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
15
C113
C113
%
*
VSS
VDD
MICROCOMPUTER
FRONT C.B
Short with tweezers.
Fig-2-2
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
Page 6
ELECTRICAL MAIN PARTS LIST
PART NO.
NO.
IC
8A-NFA-615-010 C-IC,M38B57MCH-E236FP
87-A21-419-040 C-IC,NJM14558MD-TE2
87-A21-443-040 C-IC,M62495AFP
87-A21-560-010 IC,LA1844L-A
87-070-127-110 IC,LC72131 D
87-A21-629-010 IC,SPS-442-10N
87-A21-482-010 IC,RPM6938-H4
TRANSISTOR
87-026-609-080 TR,KTA1266GR
89-213-702-010 TR,2SB1370E
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-255-010 C-TR,2SB1342
87-A30-256-010 TR,2SD1933
87-A30-190-080 TR,CC5551<HT>
87-026-245-080 TR,DTC114ES<HT>
87-A30-198-080 TR,KTC3199GR<HT>
87-A30-090-080 FET,2SK2541
87-A30-484-080 C-TR,KRA102S
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551
87-A30-091-080 FET,2SJ460
87-A30-062-080 C-TR,KRC104S
87-A30-234-080 TR,CSC4115BC
87-A30-492-080 TR,2SC5343G
89-327-143-080 TR,2SC2714O
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E<HT>
87-A30-086-070 C-TR,CSD1306E<HT>
87-A30-495-080 TR,2SA1981Y
DIODE
87-020-465-080 DIODE,1SS133 (110MA)
87-A40-455-080 DIODE,RL203 GW
87-A40-553-080 DIODE,1N4003 LES
87-A40-774-080 ZENER,UZ24BSD
87-A40-764-080 ZENER,UZ10BSC
87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-752-080 ZENER,UZ6.2BSC
87-A40-739-080 ZENER,UZ2.7BSA
87-017-149-080 ZENER,HZS6A2L
MAIN C.B
C9 87-010-196-080 CHIP CAPACITOR,0.1-25
C10 87-010-196-080 CHIP CAPACITOR,0.1-25
C11 87-010-196-080 CHIP CAPACITOR,0.1-25
C12 87-010-196-080 CHIP CAPACITOR,0.1-25
C21 87-A10-520-000 CAP,E 3300-35 M SMG
C22 87-016-051-000 CAP,E 2200-35 SMG
C25 87-010-406-080 CAP, ELECT 22-50 M 11L SME<HT>
C25 87-010-407-080 CAP, ELECT 33-50 M 11L SME<G>
C26 87-010-406-080 CAP, ELECT 22-50
C30 87-010-384-080 CAP, ELECT 100-25M11LSME
C31 87-010-263-080 CAP, ELECT 100-10V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C34 87-010-380-080 CAP, ELECT 47-16
C35 87-010-406-080 CAP, ELECT 22-50
C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-010-190-080 C-CAP,S 0.01-50 ZF
C50 87-010-384-080 CAP, ELECT 100-25 M 11L SME
C60 87-010-403-080 CAP, ELECT 3.3-50V
C61 87-010-380-080 CAP, ELECT 47-16
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C100 87-018-127-080 CAP TC-U 470P
C101 87-010-185-080 C-CAP,S 3900P-50 KB
C102 87-010-185-080 C-CAP,S 3900P-50 KB
C103 87-010-545-080 CAP, ELECT 0.22-50V
C104 87-010-545-080 CAP, ELECT 0.22-50V
C105 87-010-186-080 CAP,CHIP 4700P
C106 87-010-186-080 CAP,CHIP 4700P
C107 87-010-403-080 CAP, ELECT 3.3-50V
C108 87-010-403-080 CAP, ELECT 3.3-50V
C109 87-010-322-080 C-CAP, S 100P-50JCH
C110 87-010-322-080 C-CAP, S 100P-50JCH
C111 87-010-406-080 CAP, ELECT 22-50
C112 87-010-406-080 CAP, ELECT 22-50
C113 87-012-156-080 C-CAP, S 220P-50 J CH<G>
C113 87-A10-946-080 C-CAP, S 220P-100 J CH<HT>
C114 87-012-156-080 C-CAP, S 220P-50 J CH<G>
C114 87-A10-946-080 C-CAP, S 220P-100 J CH<HT>
C119 87-010-197-080 CAP, CHIP 0.01 DM
C120 87-010-197-080 CAP, CHIP 0.01 DM
C123 87-010-197-080 CAP, CHIP 0.01 DM<G>
C124 87-010-197-080 CAP, CHIP 0.01 DM<G>
C125 87-010-196-080 CHIP CAPACITOR,0.1-25
C126 87-010-196-080 CHIP CAPACITOR,0.1-25
C127 87-010-196-080 CHIP CAPACITOR,0.1-25
C128 87-010-196-080 CHIP CAPACITOR,0.1-25
C133 87-010-186-080 CAP,CHIP 4700P
C140 87-010-182-080 C-CAP,S 2200P-50 B
C183 87-010-387-080 CAP,E 470-25 SME<G>
C184 87-010-403-080 CAP, ELECT 3.3-50V<G>
C185 87-018-209-080 CAP, TC U 0.1-50ZF<G>
C200 87-018-195-080 CAP TC-U 1200P
C300 87-018-195-080 CAP TC-U 1200P
C301 87-010-179-080 CAP,CHIP S B1200P
C302 87-010-179-080 CAP,CHIP S B1200P
C303 87-010-178-080 CHIP CAP 1000P
C304 87-010-178-080 CHIP CAP 1000P
C305 87-010-198-080 CAP, CHIP 0.022
C307 87-010-263-080 CAP, ELECT 100-10V
C308 87-010-263-080 CAP, ELECT 100-10V
C309 87-010-311-080 C-CAP, S 12P-50J CH<G>
C309 87-010-318-080 C-CAP, S 47P-50J CH<HT>
C310 87-010-314-080 C-CAP, S 22P-50J CH<G>
C310 87-010-318-080 C-CAP, S 47P-50J CH<HT>
C311 87-010-598-080 C-CAP,S 0.068-16VRK
C312 87-010-598-080 C-CAP,S 0.068-16VRK
C313 87-010-188-080 CAP,CHIP 6800P
C314 87-010-188-080 CAP,CHIP 6800P
C315 87-010-263-080 CAP, ELECT 100-10V
C317 87-010-546-080 CAP, ELECT 0.33-50V
C318 87-010-546-080 CAP, ELECT 0.33-50V
C320 87-010-196-080 CHIP CAPACITOR,0.1-25<G>
C321 87-010-196-080 CHIP CAPACITOR,0.1-25<G>
C324 87-010-196-080 CHIP CAPACITOR,0.1-25<G>
C325 87-010-196-080 CHIP CAPACITOR,0.1-25<G>
C326 87-010-198-080 CAP, CHIP 0.022
C327 87-010-196-080 CHIP CAPACITOR,0.1-25
C350 87-010-196-080 CHIP CAPACITOR,0.1-25<G>
C360 87-010-401-080 CAP, ELECT 1-50V
C363 87-010-197-080 CAP, CHIP 0.01 DM<G>
C399 87-012-140-080 CAP 470P
C401 87-010-544-080 CAP, ELECT 0.1-50V
C402 87-010-544-080 CAP, ELECT 0.1-50V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-197-080 CAP, CHIP 0.01 DM
C407 87-010-197-080 CAP, CHIP 0.01 DM
C408 87-010-197-080 CAP, CHIP 0.01 DM
C409 87-010-182-080 C-CAP,S 2200P-50 B
C410 87-010-182-080 C-CAP,S 2200P-50 B
C411 87-010-405-080 CAP, ELECT 10-50V
C412 87-010-405-080 CAP, ELECT 10-50V
DESCRIPTIONREF. NO. KANRI
– 6 –
Page 7
PART NO.
NO.
C452 87-010-382-080 CAP, ELECT 22-25V
C453 87-010-183-080 C-CAP,S 2700P-50 B
C454 87-010-183-080 C-CAP,S 2700P-50 B
C455 87-010-183-080 C-CAP,S 2700P-50 B
C456 87-010-197-080 CAP, CHIP 0.01 DM
C458 87-010-178-080 CAP, CHIP 1000P-50KB<G>
C459 87-010-175-080 CAP, CHIP 560P-50J SL<G>
C460 87-010-196-080 CHIP CAPACITOR,0.1-25
C461 87-012-158-080 C-CAP,S 390P-50 CH
C462 87-012-158-080 C-CAP,S 390P-50 CH
C470 87-018-127-080 CAP, TC U 470P-50 BK
C605 87-010-179-080 CAP,CHIP S B1200P
C606 87-010-179-080 CAP,CHIP S B1200P
C609 87-010-213-080 C-CAP,S 0.015-50 B
C610 87-010-213-080 C-CAP,S 0.015-50 B
C611 87-010-545-080 CAP, ELECT 0.22-50V
C612 87-010-545-080 CAP, ELECT 0.22-50V
C613 87-010-545-080 CAP, ELECT 0.22-50V
C614 87-010-545-080 CAP, ELECT 0.22-50V
C615 87-010-154-080 CAP CHIP 10P
C616 87-010-248-080 CAP, ELECT 220-10
C617 87-010-248-080 CAP, ELECT 220-10
C618 87-010-405-080 CAP, ELECT 10-50V
C630 87-016-669-080 C-CAP,S 0.1-25 K B
C669 87-010-322-080 C-CAP,S 100P-50 CH<G>
C670 87-010-322-080 C-CAP,S 100P-50 CH<G>
C677 87-010-197-080 CAP, CHIP 0.01 DM
C771 87-010-263-080 CAP, ELECT 100-10V
C772 87-010-197-080 CAP, CHIP 0.01 DM
C779 87-010-971-080 CAP, CHIP 4700P-50JB<G>
C780 87-010-971-080 CAP, CHIP 4700P-50JB<G>
C782 87-010-197-080 CAP, CHIP 0.01 DM
C783 87-010-197-080 CAP, CHIP 0.01 DM
C784 87-010-197-080 CAP, CHIP 0.01 DM
C785 87-010-197-080 CAP, CHIP 0.01 DM
C786 87-010-197-080 CAP, CHIP 0.01 DM
C788 87-010-149-080 C-CAP,S 5P-50 CH
C789 87-A10-801-080 C-CAP,S 0.022-16 J B
C790 87-A10-801-080 C-CAP,S 0.022-16 J B
C791 87-010-196-080 CHIP CAPACITOR,0.1-25
C792 87-010-197-080 CAP, CHIP 0.01 DM
C793 87-010-404-080 CAP, ELECT 4.7-50V
C794 87-010-322-080 CAP, CHIP 100P-50J CH<G>
C795 87-010-197-080 CAP, CHIP 0.01 DM
C796 87-010-197-080 CAP, CHIP 0.01 DM
C797 87-010-405-080 CAP, ELECT 10-50V
C798 87-010-197-080 CAP, CHIP 0.01 DM
C799 87-010-407-080 CAP, ELECT 33-50V
C800 87-012-369-080 C-CAP,S 0.047-50F
C801 87-010-403-080 CAP, ELECT 3.3-50V
C802 87-012-369-080 C-CAP,S 0.047-50F
C803 87-010-198-080 CAP, CHIP 0.022
C804 87-010-263-080 CAP, ELECT 100-10V
C807 87-010-400-080 CAP, ELECT 0.47-50V
C808 87-010-401-080 CAP, ELECT 1-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C814 87-010-197-080 CAP, CHIP 0.01 DM
C815 87-010-400-080 CAP, ELECT 0.47-50V<HT>
C815 87-010-403-080 CAP, ELECT 3.3-50V<G>
C816 87-010-400-080 CAP, ELECT 0.47-50V<HT>
C816 87-010-403-080 CAP, ELECT 3.3-50V<G>
C818 87-010-180-080 CAP, CHIP 1500P-50 KB<G>
C821 87-010-405-080 CAP, ELECT 10-50V
C823 87-010-177-080 C-CAP,S 820P-50 SL<HT>
C823 87-012-349-080 C-CAP,S 1000P-50 J CH<G>
C824 87-010-405-080 CAP, ELECT 10-50V
C825 87-010-596-080 CAP, S 0.047-16
C831 87-010-406-080 CAP, E 22-50 M 11L<G>
C842 87-010-197-080 CAP, CHIP 0.01 DM
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C844 87-010-197-080 CAP, CHIP 0.01 DM
C851 87-010-197-080 CAP, CHIP 0.01 DM
C852 87-010-197-080 CAP, CHIP 0.01 DM
C853 87-010-197-080 CAP, CHIP 0.01 DM
C858 87-010-196-080 CHIP CAPACITOR,0.1-25
C859 87-010-196-080 CHIP CAPACITOR,0.1-25
C860 87-010-197-080 CAP, CHIP 0.01 DM
C940 87-010-197-080 CAP, CHIP S 0.01-25 KB
C942 87-010-149-080 CAP, CHIP S 5P-50 CH<G>
C947 87-010-197-080 CAP, CHIP S 0.01-25 KB
C948 87-012-140-080 CAP, CHIP S 470P-50 JCH
C952 87-010-197-080 CAP, CHIP S 0.01-25 KB<G>
C957 87-010-311-080 CAP, CHIP S 12P-50 JCH<G>
C958 87-010-197-080 CAP, CHIP S 0.01-25 KB<G>
C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C960 87-010-196-080 CHIP CAPACITOR,0.1-25
C962 87-010-401-080 CAP, ELECT 1-50V
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V
C973 87-010-197-080 CAP, CHIP 0.01 DM
C974 87-010-197-080 CAP, CHIP 0.01 DM
C979 87-010-322-080 C-CAP,S 100P-50 CH
C982 87-010-196-080 CHIP CAPACITOR,0.1-25
C983 87-010-197-080 CAP, CHIP 0.01 DM
C984 87-010-197-080 CAP, CHIP 0.01 DM
C985 87-010-322-080 CAP, CHIP 100P-50J CH<G>
C987 87-010-197-080 CAP, CHIP 0.01 DM
C989 87-010-197-080 CAP, CHIP 0.01 DM
C993 87-010-178-080 CHIP CAP 1000P
C995 87-010-178-080 CHIP CAP 1000P
C997 87-010-196-080 CHIP CAPACITOR,0.1-25
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER, SFE10.7MA5-A<HT>
CF831 87-008-423-010 FILTER, CF SFE10.7MAS3G-A<G>
CF832 87-008-261-010 FILTER, SFE10.7MA5-A<HT>
CF832 82-785-747-010 CF,MS2 GHY,R<G>
CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-099-194-010 CONN,6P 6216V
CNA1 8A-NF8-652-010 CONN ASSY,7P TID-A(480)<HT>
D951 87-A40-618-080 VARI-CAP,SVC 348(S/T)<HT>
FFE831 A8-8ZA-190-030 8ZA-1 FEUNM<HT>
FFE831 A8-6ZA-191-130 6ZA-1 FEENM<G>
J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V02<HT>
J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP312V05<G>
L101 87-A50-610-010 COIL,1UH-K(MDEC)
L102 87-A50-610-010 COIL,1UH-K(MDEC)
L451 87-007-342-010 COIL,OSC 85K BIAS
L801 87-A50-608-010 COIL,FM DET-N (TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)
L832 87-005-847-080 COIL,2.2UH(CECS)
L941 87-A50-020-010 COIL,ANT LWCOI<G>
L941 87-A50-022-010 COIL,ANT SWCOI<HT>
L942 87-A50-019-010 COIL,OSC LWCOI<G>
L942 87-A50-550-010 COIL,OSC SW-2NCOI<HT>
L943 87-A50-522-080 COIL,1MH K CEC<HT>
L944 87-A50-159-010 COIL,10MH K C2B<HT>
L951 8A-NF8-668-010 COIL,AM PACK 2(TOK)<G>
L952 87-A50-430-010 COIL,ANT MW (3BSW)<HT>
L953 87-A50-431-010 COIL,OSC MW (3BSW)<HT>
R653 87-016-669-080 C-CAP,S 0.1-25 KB
R654 87-016-669-080 C-CAP,S 0.1-25 KB
R790 87-010-197-080 CAP, CHIP 0.01 DM
R991 87-010-322-080 C-CAP,S 100P-50 CH
R993 87-010-322-080 C-CAP,S 100P-50 CH
DESCRIPTIONREF. NO. KANRI
– 7 –
Page 8
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
R995 87-010-322-080 C-CAP,S 100P-50 CH
TC941 87-011-254-080 TRIMMER,CER 20P 4.0X4.5 ECR<HT>
TC942 87-011-253-080 TRIMMER,CER 30P 4.0X4.5<G>
TC943 87-011-253-080 TRIMMER,CER 30P 4.0X4.5<HT>
W181 85-NF5-628-010 F-CABLE,7P 2.5<G>
WH1 87-A90-460-010 HLDR,WIRE 2.5-7P
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
FRONT C.B
C101 87-010-196-080 CHIP CAPACITOR,0.1-25
C102 87-012-369-080 C-CAP,S 0.047-50F
C103 87-010-374-040 CAP, ELECT 47-10
C104 87-A10-797-040 CAP,E 47-35 M 5L SRM
C105 87-010-192-080 C-CAP,S 0.022-50 F
C107 87-010-196-080 CHIP CAPACITOR,0.1-25
C108 87-010-178-080 CHIP CAP 1000P
C109 87-012-369-080 C-CAP,S 0.047-50F
C110 87-010-197-080 CAP, CHIP 0.01 DM
C111 87-010-196-080 CHIP CAPACITOR,0.1-25
C113 87-010-178-080 CHIP CAP 1000P
C114 87-010-154-080 CAP CHIP 10P
C115 87-010-175-080 CAP 560P
C116 87-010-400-040 CAP,E 0.47-50
C117 87-016-460-080 C-CAP,S 0.22-16 B
C118 87-A10-189-040 CAP,E 220-10
C119 87-A10-189-040 CAP,E 220-10
C120 87-012-156-080 C-CAP,S 220P-50 CH
C123 87-010-196-080 CHIP CAPACITOR,0.1-25
C124 87-010-196-080 CHIP CAPACITOR,0.1-25
C125 87-010-405-040 CAP,E 10-50
!
!
!
!
!
!
!
!
!
!
!
C126 87-010-196-080 CHIP CAPACITOR,0.1-25
C129 87-010-374-040 CAP,E 47-10
C210 87-012-156-080 C-CAP,S 220P-50 CH
C212 87-010-404-040 CAP,E 4.7-50 SME
C213 87-010-404-040 CAP,E 4.7-50 SME
C401 87-010-186-080 C-CAP,S 4700P-50 K B<HT>
C402 87-010-060-040 CAP,E 100-16 M 7L SRA<HT>
C403 87-010-545-040 CAP,E 0.22-50 M 11L SME<HT>
C404 87-010-322-040 C-CAP,S 100P-50 J CH GRM<HT>
C405 87-010-545-040 CAP,E 0.22-50 M 11L SME<HT>
C406 87-016-669-080 C-CAP,S 0.1-25 K B<HT>
C407 87-010-405-040 CAP,E 10-50 M 11L SME<HT>
C408 87-010-322-040 C-CAP,S 100P-50 J CH GRM<HT>
C409 87-010-378-040 CAP,E 10-16 M 11L SME<HT>
C410 87-010-196-080 C-CAP,S 0.1-25 Z F<HT>
C412 87-010-177-080 C-CAP,S 820P-50 J SL<HT>
C701 87-010-384-040 CAP,E 100-25 SME
C702 87-010-178-080 C-CAP,S1000P-50KB<G>
CN101 87-099-720-010 CONN,30P TYK-B(P)
CN701 87-A60-673-010 CONN,9P H 2MM JMT
CN801 87-099-015-010 CONN,13P 6216V
EMI401 87-008-372-080 FLTR,EMI BL01 RN1<HT>
FL201 8A-NFA-604-010 FL,10-BT-224GNK
J401 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC<HT>
L101 87-A50-434-010 COIL,CLK 4.19M(TOKO)
LED101 87-A40-317-080 LED,SLR-342VCT31 RED
S101 87-A91-555-010 SW,RTRY EC12E24504
S301 87-A90-164-080 SW,TACT SKQAB(N)
S302 87-A90-164-080 SW,TACT SKQAB(N)
S303 87-A90-164-080 SW,TACT SKQAB(N)
S304 87-A90-164-080 SW,TACT SKQAB(N)
S305 87-A90-164-080 SW,TACT SKQAB(N)
S306 87-A90-164-080 SW,TACT SKQAB(N)
S307 87-A90-164-080 SW,TACT SKQAB(N)
S308 87-A90-164-080 SW,TACT SKQAB(N)
S309 87-A90-164-080 SW,TACT SKQAB(N)
S321 87-A90-164-080 SW,TACT SKQAB(N)
S322 87-A90-164-080 SW,TACT SKQAB(N)
PART NO.
DESCRIPTIONREF. NO. KANRI
NO.
S323 87-A90-164-080 SW,TACT SKQAB(N)
S324 87-A90-164-080 SW,TACT SKQAB(N)
S325 87-A90-164-080 SW,TACT SKQAB(N)
S326 87-A90-164-080 SW,TACT SKQAB(N)
S327 87-A90-164-080 SW,TACT SKQAB(N)
S328 87-A90-164-080 SW,TACT SKQAB(N)
S329 87-A90-164-080 SW,TACT SKQAB(N)
S330 87-A90-164-080 SW,TACT SKQAB(N)
S331 87-A90-164-080 SW,TACT SKQAB(N)
SFR701 87-024-431-080 SFR,3.3K RH063EC
VR401 87-NB7-602-010 VR,RTRY 10KAX1 1V<HT>
PT C.B
C1 87-010-387-080 CAP,E 470-25 SME<HT>
C31 87-010-403-080 CAP, ELECT 3.3-50V<HT>
C183 87-010-387-080 CAP, ELECT 470-25 M<G>
C184 87-010-403-080 CAP, ELECT 3.3-50V<G>
C185 87-018-209-080 CAP, TC U 0.1-50 ZF<G>
CN1 87-A61-109-010 CONN,7P V TID-A<HT>
PT1 8A-NFA-606-010 PT,ANF-A HR<HT>
PT1 8A-NFA-608-010 PT,ANF-A EZ<G>
PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI<HT>
PT181 8A-NF8-662-010 PT,SUB ANF-8 (E)<G>
RY1 87-A91-281-010 RELAY,AC DC12V OSA-SS-212DM5<HT>
RY181 87-A90-976-010 RELAY,AC12V SDT-S-112LMR<G>
S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<HT>
T1 87-A60-317-010 TERMINAL, 1P MSC<HT>
T2 87-A60-317-010 TERMINAL, 1P MSC<HT>
T181 87-A60-317-010 TERMINAL, 1P MSC<G>
T182 87-A60-317-010 TERMINAL, 1P MSC<G>
WH181 87-A90-460-010 HLDR,WIRE 2.5-7P<G>
– 8 –
Page 9
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
E C B
CSC4115
KTA1266
KTC3198
KTC3199
E B C
2SA1981
S D G
2SJ460
2SK2541
E C B
2SC5343
CC5551
E C B
DTC114ES
D
G
2SK360
B C E
2SB1342
2SB1370
2SD1933
S
B
2SA1235
2SC2714
2SC3052
CSD1306
CMBT5401
C
E
CMBT5551
KRA102
KRA107
KRC102
KRC104
– 9 –
Page 10
FL (10-BT-224GNK) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT
– 10 –
Page 11
ANODE CONNECTION
– 11 –
Page 12
WIRING - 1 (MAIN)<HT>
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 12 –
R
S
T
U
Page 13
SCHEMATIC DIAGRAM 1 (MAIN 1 / 2 : AMP SECTION)<HT>
13
Page 14
SCHEMATIC DIAGRAM 2 (MAIN 2 / 2 : TUNER SECTION)<HT>
14
Page 15
WIRING - 2 (MAIN)<G>
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 15 –
R
S
T
U
Page 16
SCHEMATIC DIAGRAM 3 (MAIN 1 / 2 : AMP SECTION)<G>
16
Page 17
SCHEMATIC DIAGRAM 4 (MAIN 2 / 2 : TUNER SECTION)<G>
17
Page 18
WIRING - 3 (FRONT)<HT>
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 18 –
R
S
T
U
Page 19
SCHEMATIC DIAGRAM 5 (FRONT)<HT>
19
Page 20
WIRING - 4 (FRONT)<G>
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 20 –
R
S
T
U
Page 21
SCHEMATIC DIAGRAM 6 (FRONT)<G>
21
Page 22
WIRING - 5 (PT)<HT>
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 22 –
R
S
T
U
Page 23
SCHEMATIC DIAGRAM 7 (PT)<HT>
23
Page 24
WIRING - 6 (PT)<G>
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 24 –
R
S
T
U
Page 25
SCHEMATIC DIAGRAM 8 (PT)<G>
25
Page 26
WIRING - 7 (DECK)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
26
R
S
T
U
Page 27
IC BLOCK DIAGRAM
27
Page 28
IC DESCRIPTION
IC, M38B57MCH-E236FP
Pin No.
1 I-SIG I RDS signal level A/D input. (Not used)
2 I-HOLD I Hold voltage level A/D input.
3 I-SW (CD) I CD mecha SW A/D input.
4 I-DISH I CD turn-table position check A/D input.
5 I-KEY2 I KEY2 A/D input.
6 I-KEY1 I KEY1 A/D input.
7
8 O-MOTOR O Deck motor supply ON/OFF output.
9 I-RMC I System remote control signal input. ("L"=ACTIVE)
10 RESET I System reset input. ("L"=RESET)
11 I-STEREO I Tuner stereo input. ("L"=STEREO)
12 O-DSC/O-PLL_DATA O Function IC control & PLL data output.
13 VSS - GND.
14,15 XIN, XOUT I/O 4.19MHz system CLK input / output.
16 VCC - Power supply input.
17 O-PB1 O Deck 1/2 switch output. ("L"=PLAYBACK DECK 1)
Pin Name I/O
I-RDS-DATA/
(O-DSP_DATA)
I/O RDS data input / DSP IC data (V-CD) output. (Not used)
Description
18 O-STBY O Standby LED ON/OFF output. ("L"=ON)
19 O-RMT O REC mute output. ("H"=MUTE)
20 O-BIAS O Record bias ON/OFF output. ("L"=ON)
21 O-TU_ON O Tuner supply ON/OFF output. ("H"=ON)
22 O-CD_ON O CD supply ON/OFF output. ("H"= ON)
23 O-C.SHIFT O MICON clock shift output. ("L"=SHIFT)
24 O-PLL-CLK O PLL IC CLK output.
25 I-TM_BASE I 8 Hz time base input.
26 O-CLOSE O CD door close output.
27 O-CD-OPEN O
28 VEE - Power supply input for FL display.
29 O-STB(DSP) O DSP IC strobe output. (Not used)
30 K-SCAN O Initial key scan output.
31 O-PLL_CE O CD PLL IC chip enable output.
32 O-CD_LED O CD flash window LED output.
33~42 G10~G1 O FL grid output (G10~G1).
43 P22 O FL segment output (P22). (Not used)
44~58 P21~P7 O FL segment output (P21~P7).
CD door open output.
59 PHONO/P6 I/O PHONO diode input / FL segment output (P6).
60 CASINO DEMO/P5 I/O CASINO DEMO diode input (Not used) / FL segment output (P5).
61 NON-ECO/P4 I/O ECO OFF diode input / FL segment output (P4).
62 I-TU3/P3 I/O TU 3 diode input (Not used) / FL segment output (P3).
63 I-TU2/P2 I/O TU 2 diode input (Not used) / FL segment output (P2).
64 I-TU1/P1 I/O TU 1 diode input (Not used) / FL segment output (P1).
– 28 –
Page 29
I/O DescriptionPin No. Pin Name
65 O-DISH_R O CD turn-table reverse turn output.
66 O-DISH_F O CD turn-table forward turn output.
67 I-SUBQ I Sub code-Q data input.
68 O-CD_CE O CD DSP chip enable output.
69 I-WRQ I CD WRQ input.
70 O-CLK (CD) O CD control clock output .
71 O-DATA (CD) O CD control data output.
72 I-TUNE/IFC I Tuner SD input / IF count input.
73 AVSS - GND.
74 VREF - Reference voltage.
75 I-DRF I CD DRF input.
76 I-RDS_CLK I RDS clock input. (Not used)
77 I-LEVEL I Connected to GND through a resistor.
78 O-POWER O SYSTEM Power ON/OFF output. ("H"=ON)
79 I-RE_VOL I Rotary encoder A/D input.
80 I-TP_SW I Deck mecha SW A/D input.
– 29 –
Page 30
ADJUSTMENT <TUNER / DECK>
< TUNER SECTION >
< DECK SECTION >
1. Clock frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to MW 1602kHz and check that the test point is
2052kHz ± 0.045kHz.
2. MW VT Check
Settings : • Test point : TP1 (VT)
Method : Set to MW 1602kHz and check that the test point is less
than 8.0V.
Then set to 531kHz and check that the test point is more
than 0.6V.
3. FM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to FM 87.5MHz, 108.0MHz and check that the test
point is more than 0.5V (87.5MHz) and less than 8.0V
(108.0MHz).
4. MW Tracking Adjustment<G>
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L951 (1/3) ................................................... 1000kHz
Method : Set to AM(MW) 999kHz and adjust L951 (1/3) to
MAX.
5. MW VT Adjustment<HT>
Settings : • Test point : TP1 (VT)
• Adjustment location : L953
Method : Set to MW 1602kHz and adjust L953 so that the test
point becomes 8.0V ± 0.05V. Then set to MW 531kHz
and check that the test point is more than 0.3V.
6. MW Tracking Adjustment<HT>
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L952 ................................................603kHz
TC941 ...........................................1404kHz
Method : Set up TC941 to center before adjustment.
The level at 603kHz is adjust to max. by L952.
Then the level at 1404kHz is adjust to max. by TC941.
9. SW VT Adjustment<HT>
Settings : • Test point : TP1(VT)
• Adjustment location : L942
Method : Set to SW 17.9MHz and adjust L942 so that the test
point becomes 8.0V ± 0.05V. Then set to SW 5.73MHz
and check that the test point is more than 0.3V.
10. SW Tracking Adjustment<HT>
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L941 ............................................... 5.9MHz
TC943 .......................................... 17.9MHz
Method : Set up TC943 to center before adjustment.
The level at 5.9MHz is adjust to max. by L941.
Then the level at 17.9MHz is adjust to max. by TC943.
11. LW VT Adjustment<G>
Settings : • Test point : TP1 (VT)
• Adjustment location : L942
Method : Set to LW 144kHz and adjust L942 so that the test
point becomes 1.3V ± 0.05V.
Then set to LW 290kHz and check that the test point is
less than 8.0V.
12. LW Tracking Adjustment<G>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L941 ........................... 144kHz
TC942......................... 290kHz
Method : Set up TC942 to center before adjustment. The level at
144kHz is adjusted to MAX by L941. Then the level at
290kHz is adjusted to MAX by TC942.
13. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the voltage
between TP3 and TP4 becomes 0V ± 300 mV with
minimum distortion.
14. Tape Speed Adjustment (DECK 1)
Settings : • Test tape : TTA–100
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : SFR701
Method : Play back the test tape and adjust SFR701 so that the
frequency counter reads 3000Hz ± 5Hz.
15. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape and
adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
16. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point :TP8(Lch), TP9(Rch)
Method : Play back the 315Hz and 8kHz signals of the test tape
and check that the output ratio of the 8kHz signal with
respect to that of the 315Hz signal is within 4dB.
17. PB Sensitivity Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–200
• Test point : TP8(Lch), TP9(Rch)
Method : Play back the test tape and check that the output level of
the test point is 110mV ± 3.5dB.
18. REC/PB Frequency Response Check (DECK 1)
Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz / 8kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points becomes 20VU. Record and play back the 1kHz and 8kHz signals and
check that the output of the 8kHz signals is 0dB ± 5dB with
respect to that of the 1kHz signal.
19. REC/PB Sensitivity Check (DECK 1)
Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at TP8, TP9 becomes 0VU.
Record and play back the 1kHz signals and check that the
output is -2dB ± 3.5dB.
< FRONT SECTION >
20. u-CON OSC Adjustment
Settings : • Test point : TP5(K-SCAN)
• Adjustment location : L101
Method : Insert AC plug with pressing of TUNER function key and
POWER key. Adjust L101 so that the frequency across the test
point is 58.350Hz ± 0.02Hz.
7. FM Tracking Check
Settings : • Test point : TP8(Lch), TP9(Rch)
Method : Set to FM 98.0MHz and check that the test point is less
than 9dBµV(HT), less than 13dBµV(G).
8. MW IF Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L802 ............................................................ 450kHz
– 30 –
Page 31
MECHANICAL EXPLODED VIEW 1 / 1
A
A
A
A
AZG-1
24
25
26
23
22
27
I
15
19
20
18
16
FL
21
A
B
A
31
30
28
32
A
A
A
H
17
A
P.C.B
A
F
PLATE,EARTH
H
ZZM-2
14
A
P.C.B
29
A
5
8
HLDR1
A
(G ONLY)
E
HT-SINK,
FIN-S
(HT ONLY)
A
HLDR2
6
40
A
A
WIRE,
BINDER
A
E
7
3
1
39
10
E
11
12
P.C.B
29
C
D
13
G
34
D
35
(HT ONLY)
P.C.B
36
38
37
A
33
I
G
D
(G ONLY)
A
D
35
P.C.B
9
36
2
1
4
CHAS, MAIN
A
– 31 –
Page 32
MECHANICAL PARTS LIST 1 / 1
PART NO.
NO.
1 82-NF7-218-010 SPR-T,CASS
2 8A-NFZ-007-110 WINDOW,CASS 2
3 8A-NFZ-006-110 WINDOW,CASS 1
4 8A-NFZ-004-110 BOX,CASS 2
5 8A-NFZ-003-110 BOX,CASS 1
6 8A-NFZ-011-010 KNOB,RTRY VOL
7 8A-NFZ-012-010 RING,VOL
8 8A-NFZ-051-010 WINDOW,DISP H
9 86-NFZ-231-010 DMPR,70
10 8A-NFZ-041-210 CABI,FR H<HT>
10 8A-NFZ-001-210 CABI,FR U<G>
11 8A-NFZ-016-110 KEY,CASS 1
12 8A-NFZ-017-110 KEY,CASS 2P
13 87-NF4-221-010 HLDR,CABLE<HT>
14 8A-NFZ-010-010 KEY,OPE
15 8A-NFZ-013-210 KEY,CD
16 8A-NFZ-009-010 KEY,FUN
17 8A-NFA-018-010 REFLECTOR,ECO
18 8A-NFZ-008-010 KEY,POWER
19 87-CE3-023-010 BADGE,AIWA 30N SILV
20 8A-NFZ-002-010 PANEL,TRAY H
21 8A-NFA-208-010 GUIDE,FL 100-25 ANFA
22 88-913-221-110 FF-CABLE, 13P 1.25 220MM
23 8A-NFA-062-010 PANEL,TOP V-2
24 8A-NFA-215-010 PLATE,PL HR<HT >
25 8A-NFA-063-010 PANEL,LEFT V-2
26 84-ZG1-245-210 CAP,OPTICAL
27 8A-NFZ-040-010 CABI,REAR G W/O SPEC<G>
27 8A-NFA-040-010 CABI,REAR HR W/O SPEC<HT>
28 88-906-251-110 FF-CABLE,6P 1.25
29 88-NF9-213-010 HLDR,PWB MAIN
30 8A-NFA-633-010 CONN ASSY,3P (PH)
31 8A-NFA-634-010 CONN ASSY,8P RPB
32 8A-NFA-214-010 HLDR,PWB M ANFA
33 8A-NFA-065-010 PANEL,RIGHT V-2<HT>
DESCRIPTIONREF. NO. KANRI
PART NO.
33 8A-NFA-067-010 PANEL,RIGHT V-2 PL<G>
34 85-NF5-628-010 F-CABLE 7P-2.5<G>
35 8A-NF9-211-010 HLDR,PWB PT HI
!
36 8A-NFA-608-010 PT,ANF-A EZ<G>
36 8A-NFA-606-010 PT,ANF-A HR<HT>
!
!
37 87-A80-157-010 AC CORD ASSY,E BLK CC<HT>
!
37 87-A80-146-010 AC CORD ASSY,G<G>
38 87-085-185-010 BUSHING, AC CORD (E)
39 8A-NFZ-020-010 KNOB,RTRY MIC BL<HT>
40 8A-NFZ-047-010 PLATE,MIC BL<HT>
A 87-067-703-010 TAPPING SCREW, BVT2+3-10
B 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
C 87-078-191-010 S-SCREW,IT+4-10<HT>
D 87-078-200-010 S-SCREW,ITC+4-8 R<G>
E 87-067-688-010 BVTT+3-6
F 87-723-096-410 QT2+3-10W/O SLOT BL
G 87-067-641-010 UTT2+3-8(W/O SLOT)BL
H 87-721-097-410 QT2+3-12 GLD
NO.
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
– 32 –
Page 33
TAPE MECHANISM EXPLODED VIEW 1 / 1
2
54
4
3
6
5
1
59
53
46
17
16
14
15
13
19
18
24
27
26
25
28
B
29
61
55
47
17
16
38
TERMINAL,LB1
22
21
20
14
b
15
13
19
18
A
TERMINAL,LB1
23
54
6
5
28
59
27
25
55
29
22
21
20
a
A
23
31
30
10
9
57
58
12
11
8
7
45
44
43
46
44
45
43
33
24
42
37
34
b
1
51
2
a
12
4
3
1
11
10
9
8
7
57
58
40
53
52
51
47
39
50
42
56
49
48
62
41
36
26
40
33
37
32
34
1
35
38
39
– 33 –
Page 34
TAPE MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 8Z-ZM1-254-210 SPR-C,REEL R
2 8Z-ZM1-225-110 GEAR,REEL R
3 8Z-ZM1-253-110 SPR-C,AUTO SENSOR
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR
5 8Z-ZM1-212-110 LEVER,T-UP
6 8Z-ZM1-245-010 SPR-T,AUTO
7 8Z-ZM1-236-010 CLR,SLIP FF/REW
8 8Z-ZM1-252-010 SPR-C,FF/REW
9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A
10 8Z-ZM1-269-010 FELT,FF/REW 2
11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
12 8Z-ZM1-237-010 LEVER,FF/REW 2
13 8Z-ZM1-209-210 LEVER,PAUSE
14 8Z-ZM1-218-110 LEVER,E-LOCK H
15 8Z-ZM1-256-010 SPR-P,PAUSE
16 8Z-ZM1-244-010 SPR-T,T-UP
17 8Z-ZM1-247-210 SPR-T,PINCH
18 8Z-ZM1-261-110 ROLLER ASSY,PINCH
19 8Z-ZM1-221-010 LEVER,PINCH
20 8Z-ZM1-205-210 LEVER,PLAY
21 8Z-ZM1-248-110 SPR-T,BRG
22 87-A90-403-110 HEAD,RPH MS15R
23 84-ZM2-227-310 SPR-C,AZIMUTH
24 8Z-ZM1-216-010 LEVER,AUTO
25 8Z-ZM1-246-010 SPR-T,AUTO 2
26 8Z-ZM2-214-010 GEAR,IDL REW ZZM-2
27 8Z-ZM2-212-010 LEVER,STOP ZZM-2
28 8Z-ZM1-207-010 LEVER,FF
29 8Z-ZM1-206-010 LEVER,REW
30 8Z-ZM1-210-010 LEVER,REC
31 87-A90-404-010 HEAD,EH LE15B
32 8Z-ZM2-218-010 LEVER,REC LOCK ZZM-2
33 87-A91-492-010 SW,LEAF MSW18560
34 8Z-ZM1-226-010 GEAR,REEL L
35 8Z-ZM1-241-010 SPR-T,PLAY
36 8Z-ZM1-220-110 LEVER,REC SENSOR
37 8Z-ZM1-249-010 SPR-T,FR
38 8Z-ZM1-242-110 SPR-T,FF/REW
39 8Z-ZM1-229-010 GEAR,CAM
40 8Z-ZM1-232-010 GEAR,IDL FF/REW
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
41 8Z-ZM1-234-010 FLY-WHL,ZZM-1
42 8Z-ZM1-267-010 SHAFT,CAPSTAN 2
43 8Z-ZM1-228-010 GEAR,SLIP T-UP B
44 8Z-ZM1-265-010 FELT,T-UP
45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-110 SPR-C,T-UP SLIP
47 8Z-ZM1-243-210 SPR-T,STOP/PAUSE
48 87-A91-532-010 MOT,MS15U2LW1A
49 8Z-ZM1-235-010 PULLEY,MOT
50 8Z-ZM2-216-010 BELT,MAIN M
51 8Z-ZM1-260-010 SPR-P,CASETTE
52 8Z-ZM2-201-010 CHAS ASSY,ZZM-2
53 8Z-ZM1-255-110 SPR-T,E-LOCK
54 8Z-ZM2-219-010 LEVER,E-OPEN ZZM-2
55 8Z-ZM1-214-110 LEVER,LOCK
56 8Z-ZM2-211-010 FLY-WHL,ZZM-2
57 8Z-ZM1-257-110 SPR-C,F/R
58 8Z-ZM1-275-010 W-L,1.47-4-0.25
59 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT
60 87-A91-494-010 SW,LEAF MSW17820
61 8Z-ZM1-241-010 SPR-T,PLAY
62 8Z-ZM2-601-010 CONN ASSY,9P ZZM-2
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM2-220-110 V+2.6 ZZM-2
DESCRIPTIONREF. NO. KANRI
– 34 –
Page 35
SPEAKER DISASSEMBLY INSTRUCTIONS
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
12 3
How to Remove the PANEL, FR
1. Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 35 –
Fig-3
Page 36
SPEAKER PARTS LIST
SX-NBL11(Y1SL,YSC9,YSC,YSL)
PART NO.
NO.
1 8A-NSB-001-010 PANEL,FR
2 8A-NSB-003-010 GRILLE,FRAME ASSY
3 8Z-NSL-603-010 SPKR, W 120<YSC9>
3 8A-NSL-606-010 SPKR, W120<YSC,YSL,Y1SL>
4 87-NS7-611-010 CORD,SPKR
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
1 8A-NFZ-901-010 IB,H(ECA)M-BL14<HT>
1 8A-NFZ-904-010 IB,G(E)M-BL14<G>
2 8Z-NF9-701-210 RC UNIT,ZAS02
3 87-A90-118-010 ANT,WIRE FM (Z)<G>
3 87-A90-119-010 ANT,WIRE SW (5M)<HT>
4 87-043-115-010 ANT,FEEDER FM<HT>
5 87-006-225-010 AM LOOP ANT NC2<G>
5 87-006-226-010 AM LOOP ANT C0<HT>
!
6 87-A91-017-010 PLUG,CONVERSION JT-0476<HT>
NO.
DESCRIPTIONREF. NO. KANRI
– 36 –
Page 37
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9630472 0251431
Loading...