Aiwa NSXAJ-14, NSXBL-14-E, NSXBL-14, NSXBL-16 Service manual

NSX-AJ14

NSX-BL14E NSX-BL14 NSX-BL16

HS, EZ, K

SERVICE MANUAL

COMPACT DISC STEREO

CASSETTE RECEIVER

SYSTEM

NSX-AJ14

NSX-BL14<HS,EZ,K>

NSX-BL16<EZ>

NSX-BL14E<HA> CX-NBL14E SX-NBL17

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-AJ14(U)/BL14E(HA)/BL14(HS,EZ,K)/BL16(EZ),

(S/M Code No. 09-003-428-8T2).

CASSEIVER

CX-NAJ14 SX-NAJ11

CX-NBL14

BASIC TAPE MECHANISM : ZZM-2 PR1NM BASIC CD MECHANISM : AZG-1 ZA3RNDM

SPEAKER

SX-NBL11 SX-NBL16

REMOTE

CONTROLLER

RC-ZAS02

• If requiring information about the CD mechanism, see Service Manual of AZG-1 (S/M Code No. 09-001-335-3NC).

S/M Code No. 09-004-428-8R2

REVISION

DATA

SPECIFICATIONS

<FM tuner section> Tuning range 87.5 MHz to 108 MHz Usable sensitivity (IHF) U,HA,HS: 13.2 dBf

EZ,K: 16.8 dBf

Antenna terminals 75 ohms (unbalanced)

<AM/MW tuner section> Tuning range 530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1602 kHz (9 kHz step)

Usable sensitivity 350 µV/m Antenna Loop antenna

<LW tuner section><EZ,K> Tuning range 144 kHz to 290 kHz Usable sensitivity 1400 µV/m Antenna Loop antenna

<Amplifier section> Power output Rated

U: 10 W + 10 W (50 Hz - 20 kHz, T.H.D. less than 1%, 6 ohms) 15 W + 15 W (1 kHz, T.H.D. less than 10%, 6 ohms) HA: 28 W + 28 W (1 kHz, T.H.D. 1%, 6 ohms) Reference: 35 W + 35 W (1 kHz, T.H.D. 10%, 6 ohms) HS: 17 W + 17 W (1 kHz, T.H.D. 1%, 6 ohms) Reference: 20 W + 20 W (1 kHz, T.H.D. 10%, 6 ohms) EZ,K: 12 W + 12 W (1 kHz/DIN 45500, T.H.D. 1%, 6 ohms) Reference: 15 W + 15 W (1 kHz/DIN 45324, T.H.D. 10%, 6 ohms) EZ:DIN MUSIC POWER: 30 W + 30 W

Total harmonic distortion U,EZ,K: 0.1% (6 W, 1 kHz, 6 ohms,

DIN AUDIO) HA: 0.1% (14 W, 1 kHz, 6 ohms, DIN AUDIO) HS: 0.1% (8 W, 1 kHz, 6 ohms, DIN AUDIO)

Inputs VIDEO/AUX: 500 mV

HS: MIC 1.8 mV(10 kohms)

Outputs SPEAKERS: accept speakers of 6

ohms or more PHONES (stereo jack) : accepts headphones of 32 ohms or more

<Speaker system>SX-NBL17<HA>,SX-NBL11<HS,14EZ,K>,

SX-NBL16<16EZ>

Speaker System 2 way, bass reflex (magnetic shielded

type)

Speaker units Woofer:

120 mm cone type Tweeter: 20 mm cone type

Impedance 6 ohms Sensitivity 87 dB/W/m Dimensions (W x H x D) 220 x 324 x 211 mm Weight 2.0 kg

<General> Power requirements U: 120 V AC, 60 Hz

HA: 120 V/220-230 V/240 V AC (switchable), 50/60 Hz HS: 220 V AC, 60 Hz EZ,K: 230 V AC, 50 Hz

Power consumption U: 38 W

HA: 55 W HS: 60 W EZ,K: 45 W

Power consumption U: With power-economizing in standby mode mode off : 8 W

HA: With power-economizing mode off : 12 W HS,EZ,K: With power-economizing mode off : 14 W With power-economizing mode on :

0.9 W

Dimensions of main unit U,EZ,K: (W x H x D) 260 x 324 x 348 mm

(101/4 x 127/8 x 133/4 in.) HA,HS: 260 x 324 x 348 mm

Weight of main unit U: 4.8 kg (10 lbs 9 oz.)

HA: 5.7 kg HS: 5.0 kg EZ,K: 4.9 kg

<Cassette deck section> Track format 4 tracks, 2 channels stereo Frequency response 50 Hz - 8000 Hz Recording system AC bias Heads Deck 1 : Recording/Playback head

x 1, erase head x 1

Deck 2 : Playback head x 1

<Compact disc player section> Laser Semiconductor laser (λ =780 nm) D-A converter 1 bit dual Signal-to-noise ratio 85 dB (1 kHz, 0 dB) Harmonic distortion 0.05 % (1 kHz, 0 dB)

<Speaker system>SX-NAJ11 Speaker System 2 way, bass reflex (magnetic

shielded type)

Speaker units Woofer:

120 mm (43/4 in.) cone type Tweeter: 20 mm (13/16 in.) cone type

Impedance 6 ohms Sensitivity 87 dB/W/m Dimensions (W x H x D) 220 x 324 x 211 mm

(83/4 x 127/8 x 83/8 in.)

Weight 2.0 kg (4 lbs 7 oz.)

• Design and specifications are subject to change without notice.

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

s Caution: Invisible laser radiation when

open and interlocks defeated avoid exposure to beam.

s Advarsel: Usynlig laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in right figure.

PICK-UP ASSY

P.C.B

SOLDER

– 3 –

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

1 Remove the AC power cord.

11 22

2 Connect a discharging resistor at an end of lead wire that

has clips at both ends. Connect the other end of the lead wire to metal chassis.

3 Contact the other end of the discharging resistor to the

positive (+) side (+VH) of C101. (For two seconds)

4 Contact the same end of the discharging resistor as step

3 to the negative (-) side (-VH) of C102 in the same way.

(For two seconds)

5 Check that voltage across C101 and C102 has decreased

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

C101 C102

Fig-1

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.

11 22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22 33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

MICROCOMPUTER is judged to be good.

– 4 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER.

1 Remove the AC power cord.

FRONT C.B

MICROCOMPUTER

C113

VSS

VDD

MICROCOMPUTER

FRONT C.B

Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22 33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

ELECTRICAL MAIN PARTS LIST

PART NO.

NO.

8A-NFA-616-010 C-IC,M38B59MFH-E251FP<16EZ> 8A-NFA-615-010 C-IC,M38B57MCH-E236FP<EXCEPT 16EZ> 87-A21-397-010 IC,STK490-070<HA> 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-443-040 C-IC,M62495AFP

87-A21-415-010 IC,LA1843<EZ,K> 87-A21-560-010 IC,LA1844L-A<EXCEPT EZ,K> 87-070-127-110 IC,LC72131 D 87-A21-629-010 IC,SPS-442-10N 87-A21-482-010 IC,RPM6938-H4

87-A20-440-010 C-IC,BU1920FS<16EZ>

TRANSISTOR

87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F

87-A30-255-010 C-TR,2SB1342 87-A30-256-010 TR,2SD1933 87-A30-190-080 TR,CC5551 87-026-245-080 TR,DTC114ES<HS,HA> 87-A30-198-080 TR,KTC3199GR<HS,HA>

87-A30-090-080 FET,2SK2541 87-A30-484-080 C-TR,KRA102S 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551

87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-318-080 TR,CSA952K 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-234-080 TR,CSC4115BC

89-327-143-080 TR,2SC2714 (0.1W) 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E<EZ,K> 87-A30-086-070 C-TR,CSD1306E<EZ,K> 87-A30-495-080 TR,2SA1981Y

DIODE

87-A40-736-080 DIODE,1N4148M (SEM) 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-774-080 ZENER,UZ24BSD

87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840<HA> 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA<HA>

87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L 87-A40-535-080 DIODE,1N5393-GOODARK

MAIN C.B

C3 87-010-196-080 CHIP CAPACITOR,0.1-25<HA> C4 87-010-196-080 CHIP CAPACITOR,0.1-25<HA> C5 87-010-196-080 CHIP CAPACITOR,0.1-25<HA> C6 87-010-196-080 CHIP CAPACITOR,0.1-25<HA> C9 87-010-196-080 CHIP CAPACITOR,0.1-25

C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C11 87-010-196-080 CHIP CAPACITOR,0.1-25 C12 87-010-196-080 CHIP CAPACITOR,0.1-25 C19 87-A10-627-000 CAP,E 2200-50 M SMG<HA> C20 87-A10-627-000 CAP,E 2200-50 M SMG<HA>

DESCRIPTIONREF. NO. KANRI

C21 87-016-495-000 CAP,E 3300-25 M SMG<HA,U> C21 87-A10-520-000 CAP,E 3300-35 M SMG<EZ,K,HS> C22 87-016-495-000 CAP,E 3300-25 M SMG<HA> C22 87-016-051-000 CAP,E 2200-35 SMG<EZ,K,HS> C22 87-A10-011-090 CAP,E 2200-25 SMG

C25 87-010-385-080 CAP, ELECT 220-25V<HA> C25 87-010-406-080 CAP, ELECT 22-50 M 11L SME<HS> C25 87-010-407-080 CAP, ELECT 33-50 M 11L SME<EZ,K,U> C26 87-010-247-080 CAP, ELECT 100-50V<HA> C26 87-010-406-080 CAP, ELECT 22-50<EZ,K,HS,U>

C30 87-010-247-080 CAP, ELECT 100-50V<HA> C30 87-010-384-080 CAP, ELECT 100-25M11LSME<EZ,K,HS,U> C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-263-080 CAP, ELECT 100-10V<U,HA>

C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-406-080 CAP, ELECT 22-50 C36 87-010-381-080 CAP, ELECT 330-16V C38 87-A11-567-080 C-CAP,S 0.01-50 K B<EXCEPT HS> C38 87-010-190-080 C-CAP,S 0.01-50 ZF<HS>

C50 87-010-384-080 CAP, ELECT 100-25 M 11L SME C60 87-010-403-080 CAP, ELECT 3.3-50V C97 87-010-196-080 CHIP CAPACITOR,0.1-25<HA> C100 87-018-127-080 CAP TC-U 470P C101 87-010-183-080 C-CAP,S 2700P-50 B<HA>

C101 87-010-185-080 C-CAP,S 3900P-50 KB<EZ,K,HS,U> C102 87-010-183-080 C-CAP,S 2700P-50 B<HA> C102 87-010-185-080 C-CAP,S 3900P-50 KB<EZ,K,HS,U> C103 87-010-545-080 CAP, ELECT 0.22-50V C104 87-010-545-080 CAP, ELECT 0.22-50V

C105 87-010-178-080 CHIP CAP 1000P<HA> C105 87-010-186-080 CAP,CHIP 4700P<EZ,K,HS,U> C106 87-010-178-080 CHIP CAP 1000P<HA> C106 87-010-186-080 CAP,CHIP 4700P<EZ,K,HS,U> C107 87-010-404-080 CAP, ELECT 4.7-50V<HA>

C107 87-010-403-080 CAP, ELECT 3.3-50V<EZ,K,HS,U> C108 87-010-404-080 CAP, ELECT 4.7-50V<HA> C108 87-010-403-080 CAP, ELECT 3.3-50V<EZ,K,HS,U> C109 87-010-322-080 C-CAP, S 100P-50JCH<EZ,K> C109 87-010-179-080 C-CAP, S 1200P-50KB<HA>

C110 87-010-322-080 C-CAP, S 100P-50JCH<EZ,K> C110 87-010-179-080 C-CAP, S 1200P-50KB<HA> C111 87-010-391-080 CAP,E 10-35 SME<HA> C111 87-010-406-080 CAP, ELECT 22-50<EZ,K,HS,U> C112 87-010-391-080 CAP,E 10-35 SME<HA>

C112 87-010-406-080 CAP, ELECT 22-50<EZ,K,HS,U> C113 87-010-405-080 CAP, ELECT 10-50V<HA> C113 87-012-156-080 C-CAP, S 220P-50 J CH<EZ,K,U> C113 87-A10-946-080 C-CAP, S 220P-100 J CH<HS> C114 87-010-405-080 CAP, ELECT 10-50V<HA>

C114 87-012-156-080 C-CAP, S 220P-50 J CH<EZ,K,U> C114 87-A10-946-080 C-CAP, S 220P-100 J CH<HS> C119 87-010-197-080 CAP, CHIP 0.01 DM C120 87-010-197-080 CAP, CHIP 0.01 DM C123 87-010-197-080 CAP, CHIP 0.01 DM<EZ,K>

C124 87-010-197-080 CAP, CHIP 0.01 DM<EZ,K> C125 87-012-368-080 C-CAP,S 0.1-50 F<HA> C125 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K,HS,U> C126 87-012-368-080 C-CAP,S 0.1-50 F<HA> C126 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K,HS,U>

C127 87-012-368-080 C-CAP,S 0.1-50 F<HA> C127 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K,HS,U> C128 87-012-368-080 C-CAP,S 0.1-50 F<HA> C128 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K,HS,U> C129 87-A11-572-080 C-CAP,S 0.015-50 K B<HA>

C130 87-A11-572-080 C-CAP,S 0.015-50 K B<HA> C131 87-010-197-080 CAP, CHIP 0.01 DM<HA> C132 87-010-197-080 CAP, CHIP 0.01 DM<HA> C133 87-010-186-080 CAP,CHIP 4700P C140 87-010-182-080 C-CAP,S 2200P-50 B

PART NO.

NO.

DESCRIPTIONREF. NO. KANRI

– 6 –

PART NO.

NO.

C183 87-010-387-080 CAP,E 470-25 SME<U,EZ,K> C184 87-010-403-080 CAP, ELECT 3.3-50V<U,EZ,K> C185 87-018-209-080 CAP, TC U 0.1-50ZF<EZ,K> C200 87-018-195-080 CAP TC-U 1200P C300 87-018-195-080 CAP TC-U 1200P

C301 87-010-179-080 CAP,CHIP S B1200P C302 87-010-179-080 CAP,CHIP S B1200P C303 87-010-178-080 CHIP CAP 1000P C304 87-010-178-080 CHIP CAP 1000P C305 87-010-198-080 CAP, CHIP 0.022

C307 87-010-263-080 CAP, ELECT 100-10V C308 87-010-263-080 CAP, ELECT 100-10V C309 87-010-311-080 C-CAP, S 12P-50J CH<EZ,K> C309 87-010-318-080 C-CAP, S 47P-50J CH<HS,U> C310 87-010-314-080 C-CAP, S 22P-50J CH<EZ,K>

C310 87-010-318-080 C-CAP, S 47P-50J CH<HS,U> C311 87-010-598-080 C-CAP,S 0.068-16VRK C312 87-010-598-080 C-CAP,S 0.068-16VRK C313 87-010-188-080 CAP,CHIP 6800P C314 87-010-188-080 CAP,CHIP 6800P

C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT 0.33-50V C320 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K> C321 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K>

C324 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K> C325 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K> C326 87-010-198-080 CAP, CHIP 0.022 C327 87-010-196-080 CHIP CAPACITOR,0.1-25 C350 87-010-196-080 CHIP CAPACITOR,0.1-25<EZ,K>

C360 87-010-401-080 CAP, ELECT 1-50V C363 87-010-197-080 CAP, CHIP 0.01 DM<EZ,K> C399 87-012-140-080 CAP 470P C401 87-010-544-080 CAP, ELECT 0.1-50V C402 87-010-544-080 CAP, ELECT 0.1-50V

C405 87-010-197-080 CAP, CHIP 0.01 DM C406 87-010-197-080 CAP, CHIP 0.01 DM C407 87-010-197-080 CAP, CHIP 0.01 DM C408 87-010-197-080 CAP, CHIP 0.01 DM C409 87-010-182-080 C-CAP,S 2200P-50 B

C410 87-010-182-080 C-CAP,S 2200P-50 B C411 87-010-405-080 CAP, ELECT 10-50V C412 87-010-405-080 CAP, ELECT 10-50V C452 87-010-382-080 CAP, ELECT 22-25V C453 87-010-183-080 C-CAP,S 2700P-50 B

C454 87-010-183-080 C-CAP,S 2700P-50 B C455 87-010-183-080 C-CAP,S 2700P-50 B C456 87-010-197-080 CAP, CHIP 0.01 DM C458 87-010-178-080 CAP, CHIP 1000P-50KB<EZ,K> C459 87-010-175-080 CAP, CHIP 560P-50J SL<EZ,K>

C460 87-010-196-080 CHIP CAPACITOR,0.1-25 C461 87-012-158-080 C-CAP,S 390P-50 CH C462 87-012-158-080 C-CAP,S 390P-50 CH C470 87-018-127-080 CAP, TC U 470P-50 BK C605 87-010-179-080 CAP,CHIP S B1200P

C606 87-010-179-080 CAP,CHIP S B1200P C609 87-010-213-080 C-CAP,S 0.015-50 B C610 87-010-213-080 C-CAP,S 0.015-50 B C611 87-010-545-080 CAP, ELECT 0.22-50V C612 87-010-545-080 CAP, ELECT 0.22-50V

C613 87-010-545-080 CAP, ELECT 0.22-50V C614 87-010-545-080 CAP, ELECT 0.22-50V C615 87-010-154-080 CAP CHIP 10P C616 87-010-385-080 CAP, ELECT 220-25V<HA> C616 87-010-248-080 CAP, ELECT 220-10<EZ,K,HS,U>

C617 87-010-385-080 CAP, ELECT 220-25V<HA> C617 87-010-248-080 CAP, ELECT 220-10<EZ,K,HS,U> C618 87-010-405-080 CAP, ELECT 10-50V C630 87-016-669-080 C-CAP,S 0.1-25 K B C669 87-010-322-080 C-CAP,S 100P-50 CH<EZ,K,HA>

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C670 87-010-322-080 C-CAP,S 100P-50 CH<EZ,K,HA> C677 87-010-197-080 CAP, CHIP 0.01 DM C771 87-010-263-080 CAP, ELECT 100-10V C772 87-010-197-080 CAP, CHIP 0.01 DM C779 87-010-971-080 CAP, CHIP 4700P-50JB<EZ,K>

C780 87-010-971-080 CAP, CHIP 4700P-50JB<EZ,K> C782 87-010-197-080 CAP, CHIP 0.01 DM C783 87-010-197-080 CAP, CHIP 0.01 DM C784 87-010-197-080 CAP, CHIP 0.01 DM C785 87-010-197-080 CAP, CHIP 0.01 DM

C786 87-010-197-080 CAP, CHIP 0.01 DM C788 87-010-149-080 C-CAP,S 5P-50 CH C789 87-A12-052-080 C-CAP,S 0.033-25 J B<U,HA> C789 87-A11-532-080 C-CAP,S 0.022-50 J B<EZ,K> C789 87-A10-801-080 C-CAP,S 0.022-16 J B<HS>

C790 87-A12-052-080 C-CAP,S 0.033-25 J B<U,HA> C790 87-A11-532-080 C-CAP,S 0.022-50 J B<EZ,K> C790 87-A10-801-080 C-CAP,S 0.022-16 J B<HS> C791 87-010-196-080 CHIP CAPACITOR,0.1-25 C792 87-010-197-080 CAP, CHIP 0.01 DM

C793 87-010-404-080 CAP, ELECT 4.7-50V C794 87-010-322-080 CAP, CHIP 100P-50J CH<EZ,K> C795 87-010-197-080 CAP, CHIP 0.01 DM C796 87-010-197-080 CAP, CHIP 0.01 DM C797 87-010-405-080 CAP, ELECT 10-50V

C798 87-010-197-080 CAP, CHIP 0.01 DM C799 87-010-407-080 CAP, ELECT 33-50V C800 87-012-369-080 C-CAP,S 0.047-50F C801 87-010-403-080 CAP, ELECT 3.3-50V C802 87-012-369-080 C-CAP,S 0.047-50F

C803 87-010-198-080 CAP, CHIP 0.022 C804 87-010-263-080 CAP, ELECT 100-10V C807 87-010-400-080 CAP, ELECT 0.47-50V C808 87-010-401-080 CAP, ELECT 1-50V C809 87-010-401-080 CAP, ELECT 1-50V

C810 87-010-196-080 CHIP CAPACITOR,0.1-25 C814 87-010-197-080 CAP, CHIP 0.01 DM C815 87-010-400-080 CAP, ELECT 0.47-50V<HS> C815 87-010-403-080 CAP, ELECT 3.3-50V<EXCEPT HS> C816 87-010-400-080 CAP, ELECT 0.47-50V<HS>

C816 87-010-403-080 CAP, ELECT 3.3-50V<EXCEPT HS> C818 87-010-180-080 CAP, CHIP 1500P-50 KB<EZ,K> C821 87-010-405-080 CAP, ELECT 10-50V C823 87-010-177-080 C-CAP,S 820P-50 SL<HA,HS,U> C823 87-012-349-080 C-CAP,S 1000P-50 J CH<EZ,K>

C824 87-010-405-080 CAP, ELECT 10-50V C825 87-010-596-080 CAP, S 0.047-16 C831 87-010-406-080 CAP, E 22-50 M 11L<EZ,K> C842 87-010-197-080 CAP, CHIP 0.01 DM C844 87-010-197-080 CAP, CHIP 0.01 DM

C851 87-010-197-080 CAP, CHIP 0.01 DM C852 87-010-197-080 CAP, CHIP 0.01 DM C853 87-010-197-080 CAP, CHIP 0.01 DM C858 87-010-196-080 CHIP CAPACITOR,0.1-25 C859 87-010-196-080 CHIP CAPACITOR,0.1-25

C860 87-010-197-080 CAP, CHIP 0.01 DM C869 87-010-197-080 CAP, CHIP 0.01 DM<16EZ> C871 87-012-156-080 CAP, CHIP S 220P-50 JCH<16EZ> C872 87-012-156-080 CAP, CHIP S 220P-50 JCH<16EZ> C873 87-012-140-080 CAP, CHIP S 470P-50 JCH<16EZ>

C874 87-010-405-080 CAP, ELECT 10-50V<16EZ> C875 87-010-196-080 CAP, CHIP S 0.1-25 FZ<16EZ> C876 87-010-405-080 CAP, ELECT 10-50V<16EZ> C877 87-012-156-080 CAP, CHIP S 220P-50 JCH<16EZ> C878 87-010-316-080 CAP, CHIP S 33P-50 JCH<16EZ>

C879 87-010-314-080 CAP, CHIP S 22P-50 JCH<16EZ> C940 87-010-197-080 CAP, CHIP S 0.01-25 KB<EZ,K> C942 87-010-149-080 CAP, CHIP S 5P-50 CH<EZ,K> C947 87-010-197-080 CAP, CHIP S 0.01-25 KB<EZ,K> C948 87-012-140-080 CAP, CHIP S 470P-50 JCH<EZ,K>

DESCRIPTIONREF. NO. KANRI

– 7 –

PART NO.

NO.

C952 87-010-197-080 CAP, CHIP S 0.01-25 KB<EZ,K> C957 87-010-311-080 CAP, CHIP S 12P-50 JCH<EZ,K> C958 87-010-197-080 CAP, CHIP S 0.01-25 KB<EZ,K> C959 87-010-196-080 CHIP CAPACITOR,0.1-25 C960 87-010-196-080 CHIP CAPACITOR,0.1-25

C961 87-010-152-080 C-CAP,S 8P-50 CH<EXCEPT EZ,K> C962 87-010-401-080 CAP, ELECT 1-50V<EZ,K> C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C971 87-010-381-080 CAP, ELECT 330-16V C972 87-010-404-080 CAP, ELECT 4.7-50V

C973 87-010-197-080 CAP, CHIP 0.01 DM C974 87-010-197-080 CAP, CHIP 0.01 DM C979 87-010-322-080 C-CAP,S 100P-50 CH C982 87-010-196-080 CHIP CAPACITOR,0.1-25 C983 87-010-197-080 CAP, CHIP 0.01 DM

C984 87-010-197-080 CAP, CHIP 0.01 DM C985 87-010-322-080 CAP, CHIP 100P-50J CH<EZ,K> C987 87-010-197-080 CAP, CHIP 0.01 DM C989 87-010-197-080 CAP, CHIP 0.01 DM<EZ,K> C993 87-010-178-080 CHIP CAP 1000P

C995 87-010-178-080 CHIP CAP 1000P C997 87-010-196-080 CHIP CAPACITOR,0.1-25 C999 87-A11-155-080 CAP,TC U 0.01-16 Z F CF831 87-008-261-010 FILTER, SFE10.7MA5-A<EXCEPT EZ,K> CF831 87-008-423-010 FILTER, CF SFE10.7MAS3G-A<EZ,K>

CF832 87-008-261-010 FILTER, SFE10.7MA5-A<EXCEPT EZ,K> CF832 82-785-747-010 CF,MS2 GHY,R<EZ,K> CN301 87-A60-620-010 CONN,3P V 2MM JMT CN351 87-A60-625-010 CONN,8P V 2MM JMT CN601 87-099-719-010 CONN,30P TYK-B(X)

CN602 87-099-194-010 CONN,6P 6216V CNA1 8A-NF8-652-010 CONN ASSY,7P TID-A(480)<HS> CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480)<HA> FFE831 A8-8ZA-190-030 8ZA-1 FEUNM<EXCEPT EZ,K> FFE831 A8-6ZA-191-130 6ZA-1 FEENM<EZ,K>

J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC J203 87-A60-238-010 TERMINAL,SP 4P (MSC)<HA> J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V02<U,HA,HS> J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP312V05<EZ,K>

L101 87-003-383-010 COIL,1UH-S<EXCEPT U> L101 87-A50-610-010 COIL,1UH-K(MDEC) L102 87-003-383-010 COIL,1UH-S<EXCEPT U> L102 87-A50-610-010 COIL,1UH-K(MDEC) L451 87-007-342-010 COIL,OSC 85K BIAS

L801 87-A50-540-010 COIL,FM DET (TOK)<EZ,K> L801 87-A50-608-010 COIL,FM DET-N (TOK)<EXCEPT EZ,K> L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) L811 87-005-847-080 COIL,2.2UH(CECS) L832 87-005-847-080 COIL,2.2UH(CECS)

L861 87-005-847-080 COIL,2.2UH(CECS)<16EZ> L941 87-A50-020-010 COIL,ANT LWCOI<EZ,K> L942 87-A50-019-010 COIL,OSC LWCOI<EZ,K> L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<EXCEPT EZ,K> L951 8A-NF8-668-010 COIL,AM PACK 2(TOK)<EZ,K>

R131 87-A00-258-080 RES,M/F 0.22-1W J<HA> R132 87-A00-258-080 RES,M/F 0.22-1W J<HA> R653 87-A11-144-080 CAP,TC U 0.1-50 K B<HA> R654 87-A11-144-080 CAP,TC U 0.1-50 K B<HA> R790 87-010-197-080 CAP, CHIP 0.01 DM

R991 87-010-322-080 C-CAP,S 100P-50 CH R993 87-010-322-080 C-CAP,S 100P-50 CH R995 87-010-322-080 C-CAP,S 100P-50 CH TC942 87-011-253-080 TRIMMER,CER 30P 4.0X4.5<EZ,K> W181 85-NF5-628-010 F-CABLE,7P 2.5<EZ,K,U>

WH1 87-A90-510-010 HLDR,WIRE 2.5-9P<HA> WH1 87-A90-460-010 HLDR,WIRE 2.5-7P<EXCEPT HA> X861 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309<16EZ> X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309

DESCRIPTIONREF. NO. KANRI

FRONT C.B

C101 87-010-196-080 CHIP CAPACITOR,0.1-25 C102 87-012-369-080 C-CAP,S 0.047-50F C103 87-010-374-040 CAP, ELECT 47-10 C104 87-A10-797-040 CAP,E 47-35 M 5L SRM C105 87-010-192-080 C-CAP,S 0.022-50 F

C107 87-010-196-080 CHIP CAPACITOR,0.1-25 C108 87-010-178-080 CHIP CAP 1000P C109 87-012-369-080 C-CAP,S 0.047-50F C110 87-010-197-080 CAP, CHIP 0.01 DM C111 87-010-196-080 CHIP CAPACITOR,0.1-25

C113 87-010-178-080 CHIP CAP 1000P C114 87-010-154-080 CAP CHIP 10P C115 87-010-175-080 CAP 560P C116 87-010-400-040 CAP,E 0.47-50 C117 87-016-460-080 C-CAP,S 0.22-16 B

C118 87-A10-189-040 CAP,E 220-10 C119 87-A10-189-040 CAP,E 220-10 C120 87-012-156-080 C-CAP,S 220P-50 CH C123 87-010-196-080 CHIP CAPACITOR,0.1-25 C124 87-010-196-080 CHIP CAPACITOR,0.1-25

C125 87-010-405-040 CAP,E 10-50 C126 87-010-196-080 CHIP CAPACITOR,0.1-25 C129 87-010-374-040 CAP,E 47-10 C210 87-012-156-080 C-CAP,S 220P-50 CH C212 87-010-404-040 CAP,E 4.7-50 SME

C213 87-010-404-040 CAP,E 4.7-50 SME C401 87-010-186-080 C-CAP,S 4700P-50 K B<HS> C402 87-010-060-040 CAP,E 100-16 M 7L SRA<HS> C403 87-010-545-040 CAP,E 0.22-50 M 11L SME<HS> C404 87-010-322-040 C-CAP,S 100P-50 J CH GRM<HS>

C405 87-010-545-040 CAP,E 0.22-50 M 11L SME<HS> C406 87-016-669-080 C-CAP,S 0.1-25 K B<HS> C407 87-010-405-040 CAP,E 10-50 M 11L SME<HS> C408 87-010-322-040 C-CAP,S 100P-50 J CH GRM<HS> C409 87-010-378-040 CAP,E 10-16 M 11L SME<HS>

C410 87-010-196-080 C-CAP,S 0.1-25 Z F<HS> C412 87-010-177-080 C-CAP,S 820P-50 J SL<HS> C701 87-010-384-040 CAP,E 100-25 SME C702 87-010-178-080 C-CAP,S1000P-50KB<EZ,K> CN101 87-099-720-010 CONN,30P TYK-B(P)

CN701 87-A60-673-010 CONN,9P H 2MM JMT CN801 87-099-015-010 CONN,13P 6216V EMI401 87-008-372-080 FLTR,EMI BL01 RN1<HS> FL201 8A-NFA-604-010 FL,10-BT-224GNK J404 87-A61-242-010 JACK,6.3 BLK MONO W/SW VKM<HS>

L101 87-A50-434-010 COIL,CLK 4.19M(TOKO) LED101 87-A40-317-080 LED,SLR-342VCT31 RED S101 87-A91-555-010 SW,RTRY EC12E24504 S301 87-A90-164-080 SW,TACT SKQAB(N) S302 87-A90-164-080 SW,TACT SKQAB(N)

S303 87-A90-164-080 SW,TACT SKQAB(N) S304 87-A90-164-080 SW,TACT SKQAB(N) S305 87-A90-164-080 SW,TACT SKQAB(N) S306 87-A90-164-080 SW,TACT SKQAB(N) S307 87-A90-164-080 SW,TACT SKQAB(N)

S308 87-A90-164-080 SW,TACT SKQAB(N) S309 87-A90-164-080 SW,TACT SKQAB(N) S310 87-A90-164-080 SW,TACT SKQAB(N)<16EZ> S311 87-A90-164-080 SW,TACT SKQAB(N)<16EZ> S312 87-A90-164-080 SW,TACT SKQAB(N)<16EZ>

S321 87-A90-164-080 SW,TACT SKQAB(N) S322 87-A90-164-080 SW,TACT SKQAB(N) S323 87-A90-164-080 SW,TACT SKQAB(N) S324 87-A90-164-080 SW,TACT SKQAB(N) S325 87-A90-164-080 SW,TACT SKQAB(N)

S326 87-A90-164-080 SW,TACT SKQAB(N) S327 87-A90-164-080 SW,TACT SKQAB(N) S328 87-A90-164-080 SW,TACT SKQAB(N)

PART NO.

NO.

DESCRIPTIONREF. NO. KANRI

– 8 –

PART NO.

S329 87-A90-164-080 SW,TACT SKQAB(N) S330 87-A90-164-080 SW,TACT SKQAB(N) S331 87-A90-164-080 SW,TACT SKQAB(N) SFR701 87-024-431-080 SFR,3.3K RH063EC VR401 87-NB7-602-010 VR,RTRY 10KAX1 1V<HS>

PT C.B

C1 87-010-387-080 CAP,E 470-25 SME<HA,HS> C31 87-010-403-080 CAP, ELECT 3.3-50V<HA,HS> C183 87-010-387-080 CAP, ELECT 470-25 M<U,EZ,K> C184 87-010-403-080 CAP, ELECT 3.3-50V<U,EZ,K> C185 87-018-209-080 CAP, TC U 0.1-50 ZF<EZ,K>

CN1 87-A61-110-010 CONN,9P V TID-A<HA> CN1 87-A61-109-010 CONN,7P V TID-A<HS>

PT1 8A-NFA-606-010 PT,ANF-A HR<HS>

PT1 8A-NFA-608-010 PT,ANF-A EZ<EZ,K> PT1 8A-NFA-609-010 PT,ANF-A LH<HA>

PT1 8A-NFZ-610-010 PT,ANF-Z U30

PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI<HA,HS>

PT181 8A-NF8-661-010 PT,SUB ANF-8 (U)

PT181 8A-NF8-662-010 PT,SUB ANF-8 (E)<EZ,K>

RY1 87-A91-281-010 RELAY,AC DC12V OSA-SS-212DM5<HA,HS>

RY181 87-A90-976-010 RELAY,AC12V SDT-S-112LMR<U,EZ,K>

! !

S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<HA>

T1 87-A60-317-010 TERMINAL, 1P MSC<HA,HS> T2 87-A60-317-010 TERMINAL, 1P MSC<HA,HS>

T181 87-A60-317-010 TERMINAL, 1P MSC<U,EZ,K>

T182 87-A60-317-010 TERMINAL, 1P MSC<U,EZ,K> WH181 87-A90-460-010 HLDR,WIRE 2.5-7P<U,EZ,K>

NO.

DESCRIPTIONREF. NO. KANRI

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

Resistor Code

Chip resistor

Wattage Type Tolerance 1/16W 1005 5% CJ

1/16W 1/10W

1/8W

1608 2125

3216

5% 5%

Symbol

CJ CJ

Figure

Value of resistor

Form

Dimensions (mm)

0.55

Resistor Code

108 118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45 2 1.25 0.45

3.2

1.6

: A : A

– 9 –

TRANSISTOR ILLUSTRATION

E C B

CSA952 CSC4115 KTA1266 KTC3198 KTC3199

B C E

2SC3331

S D G

2SJ460 2SK2541

E B C

2SA1981

E C B

DTC114ES

E C B

CC5551

B C E

2SB1342 2SB1370 2SD1933

2SK360

2SA1235 2SC2714 2SC3052 CSD1306 CMBT5401

CMBT5551 KRA102 KRA107 KRC102 KRC104

– 10 –

FL (10-BT-224GNK) GRID ASSIGNMENT AND ANODE CONNECTION

GRID ASSIGNMENT

– 11 –

ANODE CONNECTION

– 12 –

WIRING - 1 (MAIN: U)

101112131415161718192021222324

1234567892526272829303132

- 13 -

SCHEMATIC DIAGRAM _ 1 (MAIN 1 / 2 : AMP SECTION)

– 14 –

SCHEMATIC DIAGRAM _ 2 (MAIN 2 / 2 : TUNER SECTION)

– 15 –

+ 32 hidden pages