AIWA NSX-AJ10, NSX-SZ10, NSX-SZ10E Service Manual
NSX-AJ10
U
NSX-SZ10
NSZ-SZ10E
LH
HA
SERVICE MANUAL
COMPACT DISC STEREO
CASSETTE RECEIVER
SYSTEM
NSX-AJ10
NSX-SZ10
NSX-SZ10E CX-NSZ10E SX-NSZ15
• This Service Manual is the “Revision Publishing” and replaces “Simple
Manual” NSX-AJ10(U)/NSX-SZ10(LH), (S/M Code No. 09-99C-424-8T1).
CD
CASSEIVER
CX-NAJ10 SX-NAJ12
CX-NSZ10 SX-NSZ15 RC-ZAS02
BASIC TAPE MECHANISM : ZZM-2 PR1NM / PR1NC
BASIC CD MECHANISM : AZG-1
SPEAKER
CD
MECHANISM
ZD8RNDC
ZD8RNDC
ZD8RNDM
REMOTE
CONTROLLER
• If requiring information about the CD mechanism, see Service Manual
of AZG-1 ZD8RNDM, (S/M Code No. 09-001-335-3N6) and
AZG-1 ZD8RNDC, (S/M Code No. 09-001-335-3NA).
S/M Code No. 09-003-424-8R1
REVISION
DATA
SPECIFICATIONS <HA,LH>
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)
<AM tuner section>
Tuning range 530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<Amplifier section>
Power output Rated
28 W + 28 W
(1 kHz, T.H.D. 1 %, 6 ohms)
Reference
35 W + 35 W
(1 kHz, T.H.D. 10 %, 6 ohms)
Total harmonic distortion 0.1 % (14 W, 1 kHz, 6 ohms,
DIN AUDIO)
Inputs VIDEO/AUX: 500 mV
Outputs SPEAKERS: accept speakers of 6
ohms or more
PHONES (stereo jack): accepts
headphones of 32 ohms or more
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 8000 Hz
Recording system AC bias
Heads Deck 1 : Recording/playback head
x 1, erase head x 1
Deck 2 : Playback head x 1
<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
<Speaker system SX-NSZ15>
Speaker System 2 way, bass reflex (magnetic
shielded type)
Speaker units Woofer:
120 mm cone type
Tweeter:
20mm ceramic type
Impedance 6 ohms
Sensitivity 86 dB/W/m
Dimensions (W x H x D) 220 x 324 x 204 mm
Weight 2.0 kg
<General>
Power requirements 120 V/220-230 V/240 V AC
(switchable), 50/60 Hz
Power consumption 55 W
Power consumption With power-economizing
in standby mode mode off : 12 W
With power-economizing
mode on : 0.9 W
Dimensions of main unit 260 x 324 x 346 mm
(W x H x D)
Weight of main unit 5.7 kg
• Design and specifications are subject to change without notice.
SPECIFICATIONS <U>
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)
<AM tuner section>
Tuning range 530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<Amplifier section>
Power output Rated
10 W + 10 W
(50 Hz to 20 kHz, T.H.D. 1 %, 6 ohms)
Reference
15 W + 15 W
(1 kHz, T.H.D. 10 %, 6 ohms)
Total harmonic distortion 0.1 % (6 W, 1 kHz, 6 ohms,
DIN AUDIO)
Inputs VIDEO/AUX: 500 mV
Outputs SPEAKERS: accept speakers of 6
ohms or more
PHONES (stereo jack): accepts
headphones of 32 ohms or more
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 8000 Hz
Recording system AC bias
Heads Deck 1 : Recording/playback head
x 1, erase head x 1
Deck 2 : Playback head x 1
<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
<Speaker system SX-NAJ12>
Speaker System 2 way, bass reflex (magnetic
shielded type)
Speaker units Woofer:
120 mm cone type
Tweeter:
20mm ceramic type
Impedance 6 ohms
Sensitivity 86 dB/W/m
Dimensions (W x H x D) 220 x 324 x 235 mm
Weight 2.0 kg
<General>
Power requirements 120 V AC, 60 Hz
Power consumption 38 W
Power consumption With power-economizing
in standby mode mode off : 8.0 W
With power-economizing
mode on : 0.9 W
Dimensions of main unit 260 x 324 x 346 mm
(W x H x D)
Weight of main unit 5.7 kg
• Design and specifications are subject to change without notice.
– 2 –
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
(KSM-880CAB)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
PICK-UP Assy P.C.B
solder
– 3 –
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
15
C113
C113
%
*
VSS
VDD
MICROCOMPUTER
FRONT C.B
Short with tweezers.
Fig-2-2
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
ELECTRICAL MAIN PARTS LIST
PART NO.
NO.
IC
8A-MA6-651-010 C-IC,M38B59MFH-E250FP<U,LH>
8A-NFA-615-010 C-IC,M38B57MCH-E236FP<HA>
87-A21-397-010 IC,STK490-070<LH,HA>
87-A21-419-040 C-IC,NJM14558MD-TE2
87-A21-443-040 C-IC,M62495AFP
87-A21-415-010 IC,LA1843
87-070-127-110 IC,LC72131 D
87-A21-482-010 IC,RPM6938-H4
TRANSISTOR
87-026-609-080 TR,KTA1266GR
89-213-702-010 TR,2SB1370 (1.8W)
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-255-010 C-TR,2SB1342<U>
87-A30-256-010 TR,2SD1933<U>
87-A30-190-080 TR,CC5551<U>
87-026-245-080 TR,DTC114ES<LH,HA>
87-A30-198-080 TR,KTC3199GR<LH,HA>
87-A30-090-080 FET,2SK2541
87-A30-484-080 C-TR,KRA102S
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-107-070 C-TR,CMBT5401<LH,HA>
87-A30-106-040 C-TR,CMBT5551<LH,HA>
87-A30-091-080 FET,2SJ460
87-A30-062-080 C-TR,KRC104S
87-A30-318-080 TR,CSA952K<HA>
89-333-317-880 TR,2SC3331 (0.5W)
87-A30-234-080 TR,CSC4115BC
89-327-143-080 TR,2SC2714 (0.1W)
87-A30-489-080 C-TR,KRA107S
DIODE
87-A40-736-080 DIODE,1N4148M (SEM)<U,LH>
87-020-465-080 DIODE,1SS133 (110MA)<HA>
87-A40-455-080 DIODE,RL203 GW<LH,HA>
87-A40-553-080 DIODE,1N4003 LES
87-A40-774-080 ZENER,UZ24BSD
87-A40-764-080 ZENER,UZ10BSC
87-A40-313-080 C-DIODE,MC 2840<LH,HA>
87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-768-080 ZENER,UZ16BSA<LH,HA>
87-A40-752-080 ZENER,UZ6.2BSC
87-A40-739-080 ZENER,UZ2.7BSA
87-017-149-080 ZENER,HZS6A2L
87-A40-535-080 DIODE,1N5393-GOODARK<U>
MAIN C.B
C3 87-010-196-080 CHIP CAPACITOR,0.1-25<LH,HA>
C4 87-010-196-080 CHIP CAPACITOR,0.1-25<LH,HA>
C5 87-010-196-080 CHIP CAPACITOR,0.1-25<LH,HA>
C6 87-010-196-080 CHIP CAPACITOR,0.1-25<LH,HA>
C9 87-010-196-080 CHIP CAPACITOR,0.1-25
C10 87-010-196-080 CHIP CAPACITOR,0.1-25
C11 87-010-196-080 CHIP CAPACITOR,0.1-25
C12 87-010-196-080 CHIP CAPACITOR,0.1-25
C19 87-A10-627-000 CAP,E 2200-50 M SMG<LH,HA>
C20 87-A10-627-000 CAP,E 2200-50 M SMG<LH,HA>
C21 87-016-495-000 CAP,E 3300-25 M SMG
C22 87-016-495-000 CAP,E 3300-25 M SMG<LH,HA>
C22 87-A10-011-090 CAP,E 2200-25 SMG<U>
C25 87-010-385-080 CAP, ELECT 220-25V<LH,HA>
C25 87-010-407-080 CAP, ELECT 33-50 M 11L SME<U>
C26 87-010-247-080 CAP, ELECT 100-50V<LH,HA>
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C26 87-010-406-080 CAP, ELECT 22-50<U>
C30 87-010-247-080 CAP, ELECT 100-50V<LH,HA>
C30 87-010-384-080 CAP, ELECT 100-25 M 11L SME<U>
C31 87-010-263-080 CAP, ELECT 100-10V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C33 87-010-263-080 CAP, ELECT 100-10V<U>
C34 87-010-247-080 CAP, ELECT 100-50V
C35 87-010-406-080 CAP, ELECT 22-50
C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-A11-567-080 C-CAP,S 0.01-50 K B
C50 87-010-384-080 CAP, ELECT 100-25 M 11L SME<U>
C60 87-010-403-080 CAP, ELECT 3.3-50V
C97 87-010-196-080 CHIP CAPACITOR,0.1-25<LH,HA>
C100 87-018-127-080 CAP TC-U 470P
C101 87-010-183-080 C-CAP,S 2700P-50 B<LH,HA>
C101 87-010-185-080 C-CAP,S 3900P-50 KB<U>
C102 87-010-183-080 C-CAP,S 2700P-50 B<LH,HA>
C102 87-010-185-080 C-CAP,S 3900P-50 KB<U>
C103 87-010-545-080 CAP, ELECT 0.22-50V
C104 87-010-545-080 CAP, ELECT 0.22-50V
C105 87-010-178-080 CHIP CAP 1000P<LH,HA>
C105 87-010-186-080 CAP,CHIP 4700P<U>
C106 87-010-178-080 CHIP CAP 1000P<LH,HA>
C106 87-010-186-080 CAP,CHIP 4700P<U>
C107 87-010-404-080 CAP, ELECT 4.7-50V<LH,HA>
C107 87-010-403-080 CAP, ELECT 3.3-50V<U>
C108 87-010-404-080 CAP, ELECT 4.7-50V<LH,HA>
C108 87-010-403-080 CAP, ELECT 3.3-50V<U>
C111 87-010-391-080 CAP,E 10-35 SME<LH,HA>
C111 87-010-406-080 CAP, ELECT 22-50<U>
C112 87-010-391-080 CAP,E 10-35 SME<LH,HA>
C112 87-010-406-080 CAP, ELECT 22-50<U>
C113 87-010-405-080 CAP, ELECT 10-50V<LH,HA>
C113 87-012-156-080 C-CAP, S 220P-50 J CH<U>
C114 87-010-405-080 CAP, ELECT 10-50V<LH,HA>
C114 87-012-156-080 C-CAP, S 220P-50 J CH<U>
C119 87-010-197-080 CAP, CHIP 0.01 DM
C120 87-010-197-080 CAP, CHIP 0.01 DM
C125 87-012-368-080 C-CAP,S 0.1-50 F<LH,HA>
C125 87-010-196-080 CHIP CAPACITOR,0.1-25<U>
C126 87-012-368-080 C-CAP,S 0.1-50 F<LH,HA>
C126 87-010-196-080 CHIP CAPACITOR,0.1-25<U>
C127 87-012-368-080 C-CAP,S 0.1-50 F<LH,HA>
C127 87-010-196-080 CHIP CAPACITOR,0.1-25<U>
C128 87-012-368-080 C-CAP,S 0.1-50 F<LH,HA>
C128 87-010-196-080 CHIP CAPACITOR,0.1-25<U>
C129 87-A10-592-080 C-CAP,S 0.015-50 K B<LH,HA>
C130 87-A10-592-080 C-CAP,S 0.015-50 K B<LH,HA>
C131 87-010-197-080 CAP, CHIP 0.01 DM<LH,HA>
C132 87-010-197-080 CAP, CHIP 0.01 DM<LH,HA>
C133 87-010-186-080 CAP,CHIP 4700P
C140 87-010-182-080 C-CAP,S 2200P-50 B
C183 87-010-387-080 CAP,E 470-25 SME<U>
C184 87-010-403-080 CAP, ELECT 3.3-50V<U>
C200 87-018-195-080 CAP TC-U 1200P
C300 87-018-195-080 CAP TC-U 1200P
C301 87-010-179-080 CAP,CHIP S B1200P
C302 87-010-179-080 CAP,CHIP S B1200P
C303 87-010-178-080 CHIP CAP 1000P
C304 87-010-178-080 CHIP CAP 1000P
C305 87-010-198-080 CAP, CHIP 0.022
C307 87-010-263-080 CAP, ELECT 100-10V
C308 87-010-263-080 CAP, ELECT 100-10V
C311 87-010-598-080 C-CAP,S 0.068-16VRK
C312 87-010-598-080 C-CAP,S 0.068-16VRK
C313 87-010-188-080 CAP,CHIP 6800P
C314 87-010-188-080 CAP,CHIP 6800P
C315 87-010-263-080 CAP, ELECT 100-10V
C317 87-010-546-080 CAP, ELECT 0.33-50V
C318 87-010-546-080 CAP, ELECT 0.33-50V
DESCRIPTIONREF. NO. KANRI
– 6 –
PART NO.
NO.
C326 87-010-198-080 CAP, CHIP 0.022
C327 87-010-196-080 CHIP CAPACITOR,0.1-25
C360 87-010-401-080 CAP, ELECT 1-50V
C399 87-012-140-080 CAP 470P
C401 87-010-544-080 CAP, ELECT 0.1-50V
C402 87-010-544-080 CAP, ELECT 0.1-50V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-197-080 CAP, CHIP 0.01 DM
C407 87-010-197-080 CAP, CHIP 0.01 DM
C408 87-010-197-080 CAP, CHIP 0.01 DM
C409 87-010-182-080 C-CAP,S 2200P-50 B
C410 87-010-182-080 C-CAP,S 2200P-50 B
C411 87-010-405-080 CAP, ELECT 10-50V
C412 87-010-405-080 CAP, ELECT 10-50V
C452 87-010-382-080 CAP, ELECT 22-25V
C453 87-010-183-080 C-CAP,S 2700P-50 B
C454 87-010-183-080 C-CAP,S 2700P-50 B
C455 87-010-183-080 C-CAP,S 2700P-50 B
C456 87-010-197-080 CAP, CHIP 0.01 DM
C460 87-010-196-080 CHIP CAPACITOR,0.1-25
C461 87-012-158-080 C-CAP,S 390P-50 CH
C462 87-012-158-080 C-CAP,S 390P-50 CH
C605 87-010-179-080 CAP,CHIP S B1200P
C606 87-010-179-080 CAP,CHIP S B1200P
C609 87-010-213-080 C-CAP,S 0.015-50 B
C610 87-010-213-080 C-CAP,S 0.015-50 B
C611 87-010-545-080 CAP, ELECT 0.22-50V
C612 87-010-545-080 CAP, ELECT 0.22-50V
C613 87-010-545-080 CAP, ELECT 0.22-50V
C614 87-010-545-080 CAP, ELECT 0.22-50V
C615 87-010-154-080 CAP CHIP 10P
C616 87-010-385-080 CAP, ELECT 220-25V<LH,HA>
C616 87-010-248-080 CAP, ELECT 220-10<U>
C617 87-010-385-080 CAP, ELECT 220-25V<LH,HA>
C617 87-010-248-080 CAP, ELECT 220-10<U>
C618 87-010-405-080 CAP, ELECT 10-50V
C630 87-016-669-080 C-CAP,S 0.1-25 K B
C669 87-010-322-080 C-CAP,S 100P-50 CH<LH,HA>
C670 87-010-322-080 C-CAP,S 100P-50 CH<LH,HA>
C677 87-010-197-080 CAP, CHIP 0.01 DM
C771 87-010-263-080 CAP, ELECT 100-10V
C772 87-010-197-080 CAP, CHIP 0.01 DM
C782 87-010-197-080 CAP, CHIP 0.01 DM
C783 87-010-197-080 CAP, CHIP 0.01 DM
C784 87-010-197-080 CAP, CHIP 0.01 DM
C785 87-010-197-080 CAP, CHIP 0.01 DM
C786 87-010-197-080 CAP, CHIP 0.01 DM
C788 87-010-149-080 C-CAP,S 5P-50 CH
C789 87-A12-052-080 C-CAP,S 0.033-25 J B
C790 87-A12-052-080 C-CAP,S 0.033-25 J B
C791 87-010-196-080 CHIP CAPACITOR,0.1-25
C792 87-010-197-080 CAP, CHIP 0.01 DM
C793 87-010-404-080 CAP, ELECT 4.7-50V
C795 87-010-197-080 CAP, CHIP 0.01 DM
C796 87-010-197-080 CAP, CHIP 0.01 DM
C797 87-010-405-080 CAP, ELECT 10-50V
C798 87-010-197-080 CAP, CHIP 0.01 DM
C799 87-010-407-080 CAP, ELECT 33-50V
C800 87-012-369-080 C-CAP,S 0.047-50F
C801 87-010-403-080 CAP, ELECT 3.3-50V
C802 87-012-369-080 C-CAP,S 0.047-50F
C803 87-010-198-080 CAP, CHIP 0.022
C804 87-010-263-080 CAP, ELECT 100-10V
C807 87-010-400-080 CAP, ELECT 0.47-50V
C808 87-010-401-080 CAP, ELECT 1-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C814 87-010-197-080 CAP, CHIP 0.01 DM
C815 87-010-403-080 CAP, ELECT 3.3-50V
C816 87-010-403-080 CAP, ELECT 3.3-50V
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C821 87-010-405-080 CAP, ELECT 10-50V
C823 87-010-177-080 C-CAP,S 820P-50 SL
C824 87-010-405-080 CAP, ELECT 10-50V
C825 87-010-596-080 CAP, S 0.047-16
C842 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-010-197-080 CAP, CHIP 0.01 DM
C851 87-010-197-080 CAP, CHIP 0.01 DM
C852 87-010-197-080 CAP, CHIP 0.01 DM
C853 87-010-197-080 CAP, CHIP 0.01 DM
C858 87-010-196-080 CHIP CAPACITOR,0.1-25
C859 87-010-196-080 CHIP CAPACITOR,0.1-25
C860 87-010-197-080 CAP, CHIP 0.01 DM
C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C960 87-010-196-080 CHIP CAPACITOR,0.1-25
C961 87-010-152-080 C-CAP,S 8P-50 CH
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V
C973 87-010-197-080 CAP, CHIP 0.01 DM
C974 87-010-197-080 CAP, CHIP 0.01 DM
C979 87-010-322-080 C-CAP,S 100P-50 CH
C982 87-010-196-080 CHIP CAPACITOR,0.1-25
C983 87-010-197-080 CAP, CHIP 0.01 DM
C984 87-010-197-080 CAP, CHIP 0.01 DM
C987 87-010-197-080 CAP, CHIP 0.01 DM
C993 87-010-178-080 CHIP CAP 1000P
C995 87-010-178-080 CHIP CAP 1000P
C997 87-010-196-080 CHIP CAPACITOR,0.1-25
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER, SFE10.7MA5-A
CF832 87-008-261-010 FILTER, SFE10.7MA5-A
CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-099-194-010 CONN,6P 6216V
CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480)<LH,HA>
FFE831 A8-8ZA-193-070 8ZA-1 YFEUNC<U,LH>
FFE831 A8-8ZA-190-030 8ZA-1 FEUNM<HA>
J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC
J203 87-A60-238-010 TERMINAL,SP 4P (MSC)<HA,LH>
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02
L101 87-003-383-010 COIL,1UH-S
L102 87-003-383-010 COIL,1UH-S
L451 87-007-342-010 COIL,OSC 85K BIAS
L801 87-A50-540-010 COIL,FM DET (TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)
L832 87-005-847-080 COIL,2.2UH(CECS)
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)
R131 87-A00-258-080 RES,M/F 0.22-1W J<LH,HA>
R132 87-A00-258-080 RES,M/F 0.22-1W J<LH,HA>
R653 87-A11-144-080 CAP,TC U 0.1-50 K B<HA>
R654 87-A11-144-080 CAP,TC U 0.1-50 K B<HA>
R790 87-010-197-080 CAP, CHIP 0.01 DM
R991 87-010-322-080 C-CAP,S 100P-50 CH
R993 87-010-322-080 C-CAP,S 100P-50 CH
R995 87-010-322-080 C-CAP,S 100P-50 CH
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P<LH,HA>
WH1 87-A90-460-010 HLDR,WIRE 2.5-7P<U>
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
FRONT C.B
C101 87-010-196-080 CHIP CAPACITOR,0.1-25
C102 87-012-369-080 C-CAP,S 0.047-50F
C103 87-010-374-040 CAP, ELECT 47-10
C104 87-A10-797-040 CAP,E 47-35 M 5L SRM
C105 87-010-192-080 C-CAP,S 0.022-50 F
C107 87-010-196-080 CHIP CAPACITOR,0.1-25
DESCRIPTIONREF. NO. KANRI
– 7 –
Loading...