NSX-SZ30
LH,HR,HS,HT
SERVICE MANUAL
STEREO SYSTEM
NSX-SZ30
<LH>
NSX-SZ30
<HR,HS,HT>
• This Service Manual contains information about the difference between
• This Service Manual is for VA model.
• Refer to MAIN C.B parts number for difference of model.
COMPACT DISC
CD
CASSEIVER
CX-NSZ30
CX-NSZ30
NSX-SZ30 (VA model) and NSX-SZ20 / SZ30. If requiring the other
information, see Service Manual as listed on page 2.
8A-NF9-701-010 is for NSX-SZ30<LH,HR,HS,HT> VA model.
TAPE
MECHANISM
ZZM-3 PR1NF AZG-1 YKZD3RDF
BASIC TAPE MECHANISM : ZZM-3, 6ZM-3
BASIC CD MECHANISM : AZG-1
CD
MECHANISM
SPEAKERSYSTEM
SX-NSZ52
REMOTE
CONTROLLER
RC-ZAS02
RC-ZAS016ZM-3 PR2NM AZG-1 ZD3RDM
• If requiring information about the CD mechanism, see Service Manual
of AZG-1, (S/M Code No. 09-001-335-3N8)
S/M Code No. 09-011-423-3S4
SUPPLEMENT
DATA
VA MODEL
MODEL NAME
BASE MODEL
S/M Code No.
NSX-SZ30<LH>
NSX-SZ30<HR>
NSX-SZ20<LH> 09-001-423-4R1
NSX-SZ20<HR>
NSX-SZ30<HS,HT> NSX-SZ30<HS,HT>
09-005-423-4R3
09-007-423-3R1
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
(KSS – 213F)
CD PICK-UP Assy. PWB
Solder
– 2 –
SPECIFICATIONS
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminals 75 ohms (unbalanced)
<AM/MW tuner section>
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<SW tuner section> <HR only>
Tuning range 5.730 MHz to 17.900 MHz
Usable sensitivity 40 µV (IEC)
Antenna Wire antenna
<Amplifier section>
Power output Rated
LH: 65 W + 65 W
(1 kHz, THD 1%, 6 ohms)
HR,HS,HT: 40 W + 40 W
(6 ohms, THD 1%, 1 kHz)
Reference
LH: 80 W + 80 W
(1 kHz, THD 10%, 6 ohms)
HR,HS,HT: 50 W + 50 W
(6 ohms, THD 10%, 1 kHz)
Total harmonic distortion LH: 0.05%
(40 W, 1 kHz, 6 ohms, DIN AUDIO)
HR,HS,HT: 0.08%
(25 W, 1 kHz, 6 ohms, DIN AUDIO)
Inputs VIDEO/AUX: 500 mV
HR,HS,HT only: MIC: 1.0 mV (10 kohms)
Outputs SPEAKERS: accept speakers of 6
ohms or more
PHONES (stereo jack): accept
headphones of 32 ohms or more
<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
<Speaker system SX–NSZ52>
Speaker system 3 way, bass reflex (magnetic
shielded type)
Speaker units Woofer: 140 mm cone type
Tweeter: 60 mm cone type
Super tweeter: 20 mm ceramic type
Impedance 6 ohms
Output sound pressure level 87 dB/W/m
Dimensions (W x H x D) 240 x 324 x 270 mm
Weight 4.0 kg
<General>
Power requirements LH,HR,HT: 120 V/220-230 V/240 V AC
(switchable), 50/60 Hz
HS: 220 V AC, 60 Hz
Power consumption LH: 125 W
HR,HS,HT: 80 W
Power consumption in standby mode
With power-economizing mode off
LH: 17 W
HR,HS,HT: 13 W
With power-economizing mode on
0.9 W
Dimensions of main unit 260 x 328 x 335 mm
(W x H x D)
Weight of main unit LH: 7.1 kg
HR,HS,HT: 6.3 kg
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 15 kHz
Recording system AC bias
Heads Deck 1: Playback head x 1
Deck 2: Recording/Playback head x 1,
erase head x 1
• Design and specifications are subject to change without notice.
• The word "BBE"and the "BBE symbol" are trademarks of BBE
Sound, Inc.
Under license from BBE Sound,Inc.
– 3 –
ELECTRICAL MAIN PARTS LIST
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
IC
87-070-127-110 IC,LC72131D<HR,HS,HT>
87-A21-928-010 IC,LC72131D-N<LH>
87-A21-401-040 C-IC,M61503FP
87-A21-482-010 IC,RPM6938-H4<HR,HS,HT>
87-A21-831-010 IC,SPS-442-1-F1<LH>
87-A21-560-010 IC,LA1844L-A
87-A21-419-040 C-IC,NJM14558MD-TE2
8A-NF9-604-110 C-IC,UPD780226GF-019-3BA
87-A21-269-010 IC,EW732<LH>
87-020-454-010 IC,DN6851<HR,HS,HT>
TRANSISTOR
87-026-609-080 TR,KTA1266GR
89-213-702-010 TR,2SB1370E
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-026-245-080 TR,DTC114ES
87-A30-198-080 TR,KTC3199GR
87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551
87-A30-091-080 FET,2SJ460
87-A30-062-080 C-TR,KRC104S
87-A30-090-080 FET,2SK2541
87-A30-318-080 TR,CSA952K
87-A30-329-080 TR,CD1585BC
87-A30-074-080 C-TR,RT1P 141C
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-087-080 C-FET,2SK2158
87-A30-086-040 C-TR,CSD1306E<HR,HT>
89-503-602-080 C-FET,2SK360E<HR,HT>
87-A30-234-080 TR,CSC4115BC
89-327-143-080 C-TR,2SC2714(O)
87-A30-072-080 C-TR,RT1P 144C
87-A30-492-080 TR,2SC5343G
87-A30-495-080 TR,2SA1981Y
87-A30-190-080 TR,CC5551
87-A30-162-010 FET,2SK2937
87-A30-528-010 TR,2SB1686<HR,HS,HT>
87-A30-529-010 TR,2SD2642<HR,HS,HT>
87-A30-525-010 TR,2SB1228<LH>
87-A30-526-010 TR,2SD1830<LH>
DIODE
87-A40-553-080 DIODE,1N4003 LES
87-A40-776-080 ZENER,UZ27BSD
87-A40-764-080 ZENER,UZ10BSC
87-A40-313-080 C-DIODE,MC 2840
87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-752-080 ZENER,UZ6.2BSC
87-A40-739-080 ZENER,UZ2.7BSA
87-020-465-080 DIODE,1SS133
87-A40-854-080 ZENER,UZ15BSA
87-A40-535-080 DIODE,1N5393-GOODARK<HR,HS,HT>
87-017-149-080 ZENER,HZS6A2L
87-A40-393-090 DIODE,1N5402GW(F20)
87-A40-749-080 ZENER,UZ5.6BSB
87-A40-455-080 DIODE,RL203 GW
MAIN C.B
C3 87-012-368-080 C-CAP,S 0.1-50 F
C4 87-012-368-080 C-CAP,S 0.1-50 F
C5 87-012-368-080 C-CAP,S 0.1-50 F
C6 87-012-368-080 C-CAP,S 0.1-50 F
C9 87-012-368-080 C-CAP,S 0.1-50 F
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C10 87-012-368-080 C-CAP,S 0.1-50 F
C11 87-012-368-080 C-CAP,S 0.1-50 F
C12 87-012-368-080 C-CAP,S 0.1-50 F
C19 87-A10-627-000 CAP,E 2200-50 SMG
C20 87-A10-627-000 CAP,E 2200-50 SMG
C21 87-016-495-000 CAP,E 3300-25 M SMG
C22 87-016-495-000 CAP,E 3300-25 M SMG
C25 87-010-385-080 CAP, ELECT 220-25V
C26 87-010-247-080 CAP, ELECT 100-50V<LH>
C26 87-010-384-080 CAP, ELECT 100-25M<HR,HS,HT>
C27 87-010-385-080 CAP, ELECT 220-25V<HR,HS,HT>
C28 87-010-384-080 CAP, ELECT 100-25M<HR,HS,HT>
C30 87-010-430-080 CAP, ELECT 100-63
C31 87-010-263-080 CAP, ELECT 100-10V
C32 87-010-197-080 CAP, CHIP 0.01-25 K B
C34 87-010-247-080 CAP, ELECT 100-50V
C35 87-010-380-080 CAP, ELECT 47-16 M
C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-010-197-080 CAP, CHIP 0.01-25 K B
C60 87-010-403-080 CAP, ELECT 3.3-50V
C61 87-010-260-080 CAP, ELECT 47-25V
C97 87-010-196-080 CHIP CAPACITOR,0.1-25
C101 87-010-185-080 C-CAP,S 3900P-50 B
C102 87-010-185-080 C-CAP,S 3900P-50 B
C103 87-010-545-080 CAP,E 0.22-50 M
C104 87-010-545-080 CAP,E 0.22-50 M
C105 87-010-187-080 CAP CHIP S5600P
C106 87-010-187-080 CAP CHIP S5600P
C107 87-010-404-080 CAP, ELECT 4.7-50V
C108 87-010-404-080 CAP, ELECT 4.7-50V
C111 87-010-391-080 CAP,E 10-35 SME
C112 87-010-391-080 CAP,E 10-35 SME
C113 87-A10-946-080 C-CAP,S 220P-100 J CH
C114 87-A10-946-080 C-CAP,S 220P-100 J CH
C119 87-010-197-080 C-CAP,S 0.01-25
C120 87-010-197-080 C-CAP,S 0.01-25
C125 87-012-368-080 C-CAP,S 0.1-50 F
C126 87-012-368-080 C-CAP,S 0.1-50 F
C127 87-012-368-080 C-CAP,S 0.1-50 F
C128 87-012-368-080 C-CAP,S 0.1-50 F
C129 87-010-191-080 C-CAP,S 0.015-50 F
C130 87-010-191-080 C-CAP,S 0.015-50 F
C131 87-010-197-080 CAP, CHIP 0.01-25 K B
C132 87-010-197-080 CAP, CHIP 0.01-25 K B
C133 87-010-186-080 CAP,CHIP 4700P-50 K
C140 87-010-182-080 C-CAP,S 2200P-50 B
C141 87-010-196-080 CHIP CAPACITOR,0.1-25
C186 87-010-196-080 CHIP CAPACITOR,0.1-25
C187 87-010-405-080 CAP, ELECT 10-50V
C188 87-010-405-080 CAP, ELECT 10-50V
C239 87-010-196-080 CHIP CAPACITOR,0.1-25
C301 87-010-178-080 C-CAP,S 1000-50 K B
C302 87-010-178-080 C-CAP,S 1000-50 K B
C303 87-010-178-080 C-CAP,S 1000-50 K B
C304 87-010-178-080 C-CAP,S 1000-50 K B
C307 87-010-263-080 CAP, ELECT 100-10V
C308 87-010-263-080 CAP, ELECT 100-10V
C309 87-010-318-080 C-CAP,S 47P-50 CH
C310 87-010-318-080 C-CAP,S 47P-50 CH
C313 87-010-188-080 CAP,CHIP 6800P
C314 87-010-188-080 CAP,CHIP 6800P
C315 87-010-263-080 CAP, ELECT 100-10V
C317 87-010-546-080 CAP, ELECT 0.33-50V
C318 87-010-546-080 CAP, ELECT 0.33-50V
C326 87-010-198-080 CAP, CHIP 0.022-25 K
C327 87-012-368-080 C-CAP,S 0.1-50 F
C360 87-010-401-080 CAP, ELECT 1-50V
C399 87-012-140-080 C-CAP,S 470P-50 J
C401 87-010-544-080 CAP, ELECT 0.1-50V
C402 87-010-544-080 CAP, ELECT 0.1-50V
– 4 –
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
C403 87-010-321-080 CHIP CAPACITOR,82P(J)
C404 87-010-321-080 CHIP CAPACITOR,82P(J)
C405 87-010-197-080 CAP, CHIP 0.01-25 K B
C406 87-010-197-080 CAP, CHIP 0.01-25 K B
C407 87-010-197-080 CAP, CHIP 0.01-25 K B
C408 87-010-197-080 CAP, CHIP 0.01-25 K B
C409 87-010-182-080 C-CAP,S 2200P-50 B
C410 87-010-182-080 C-CAP,S 2200P-50 B
C411 87-010-405-080 CAP, ELECT 10-50V
C412 87-010-405-080 CAP, ELECT 10-50V
C452 87-010-382-080 CAP, ELECT 22-25V
C453 87-010-183-080 C-CAP,S 2700P-50 B
C454 87-010-183-080 C-CAP,S 2700P-50 B
C455 87-010-183-080 C-CAP,S 2700P-50 B
C456 87-010-197-080 CAP, CHIP 0.01-25 K B
C457 87-A12-361-080 CAP, M 5600P-100 J CP
C460 87-010-196-080 CHIP CAPACITOR,0.1-25
C461 87-012-158-080 C-CAP,S 390P-50 CH
C462 87-012-158-080 C-CAP,S 390P-50 CH
C470 87-018-127-080 CAP, CER 470P-50V
C605 87-010-184-080 CAP,CHIP S 3300P-50 KB<LH>
C605 87-010-179-080 CAP,CHIP S 1200P-50 KB<HR,HS,HT>
C606 87-010-184-080 CAP,CHIP S 3300P-50 KB<LH>
C606 87-010-179-080 CAP,CHIP S 1200P-50 KB<HR,HS,HT>
C609 87-010-213-080 C-CAP,S 0.015-50 B
C610 87-010-213-080 C-CAP,S 0.015-50 B
C611 87-010-545-080 CAP, ELECT 0.22-50V
C612 87-010-545-080 CAP, ELECT 0.22-50V
C613 87-010-545-080 CAP, ELECT 0.22-50V
C614 87-010-545-080 CAP, ELECT 0.22-50V
C615 87-010-154-080 CAP CHIP 10P-50 CH
C616 87-010-221-080 CAP, ELECT 470-10 M
C617 87-010-221-080 CAP, ELECT 470-10 M
C618 87-010-405-080 CAP, ELECT 10-50V
C630 87-016-669-080 C-CAP,S 0.1-25 K B
C631 87-010-185-080 C-CAP,S 3900P-50 B
C632 87-010-185-080 C-CAP,S 3900P-50 B
C633 87-016-369-080 C-CAP,S 0.033-25 K B
C634 87-016-369-080 C-CAP,S 0.033-25 K B
C669 87-010-322-080 C-CAP,S 100P-50 CH
C670 87-010-322-080 C-CAP,S 100P-50 CH
C671 87-010-196-080 CHIP CAPACITOR,0.1-25 Z F<HR,HS,HT>
C672 87-010-196-080 CHIP CAPACITOR,0.1-25 Z F<HR,HS,HT>
C673 87-010-182-080 C-CAP,S 2200P-50 B<HR,HS,HT>
C677 87-010-197-080 CAP, CHIP 0.01-25 K B
C771 87-010-263-080 CAP, ELECT 100-10V
C772 87-010-197-080 CAP, CHIP 0.01-25 K B
C782 87-010-197-080 CAP, CHIP 0.01-25 K B
C783 87-010-197-080 CAP, CHIP 0.01-25 K B
C784 87-010-197-080 CAP, CHIP 0.01-25 K B
C785 87-010-197-080 CAP, CHIP 0.01-25 K B
C786 87-010-197-080 CAP, CHIP 0.01-25 K B
C788 87-010-149-080 C-CAP,S 5P-50 CH
C789 87-A12-052-080 C-CAP,S 0.033-25 J B<LH>
C789 87-A10-801-080 C-CAP,S 0.022-16 J B<HR,HS,HT>
C790 87-A12-052-080 C-CAP,S 0.033-25 J B<LH>
C790 87-A10-801-080 C-CAP,S 0.022-16 J B<HR,HS,HT>
C791 87-010-196-080 CHIP CAPACITOR,0.1-25
C792 87-010-197-080 CAP, CHIP 0.01-25 K B
C793 87-010-404-080 CAP, ELECT 4.7-50V
C795 87-010-197-080 CAP, CHIP 0.01-25 K B
C796 87-010-197-080 CAP, CHIP 0.01-25 K B
C797 87-010-405-080 CAP, ELECT 10-50V
C798 87-010-197-080 CAP, CHIP 0.01-25 K B
C799 87-010-407-080 CAP, ELECT 33-50V
C800 87-012-369-080 C-CAP,S 0.047-50F
C801 87-010-403-080 CAP, ELECT 3.3-50V
C802 87-010-194-080 CAP, CHIP 0.047-25 Z F
C803 87-010-198-080 CAP, CHIP 0.022-25 K B
C804 87-010-263-080 CAP, ELECT 100-10V
DESCRIPTIONREF. NO. KANRI
C807 87-010-400-080 CAP, ELECT 0.47-50V
C808 87-010-401-080 CAP, ELECT 1-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C814 87-010-197-080 CAP, CHIP 0.01-25 K B
C815 87-010-400-080 CAP, ELECT 0.47-50V
C816 87-010-400-080 CAP, ELECT 0.47-50V
C821 87-010-405-080 CAP, ELECT 10-50V
C823 87-010-177-080 C-CAP,S 820P-50 SL
C824 87-010-404-080 CAP, ELECT 4.7-50 M
C825 87-010-596-080 CAP, S 0.047-16
C842 87-010-197-080 CAP, CHIP 0.01-25 K B
C844 87-010-197-080 CAP, CHIP 0.01-25 K B
C850 87-010-260-080 CAP, ELECT 47-25V
C851 87-010-197-080 CAP, CHIP 0.01-25 K B
C852 87-010-197-080 CAP, CHIP 0.01-25 K B
C853 87-010-197-080 CAP, CHIP 0.01-25 K B
C858 87-010-196-080 CHIP CAPACITOR,0.1-25
C859 87-010-196-080 CHIP CAPACITOR,0.1-25
C860 87-010-197-080 CAP, CHIP 0.01-25 K B
C940 87-010-197-080 CAP, CHIP 0.01-25 K B<HR,HT>
C941 87-010-314-080 C-CAP,S 22P-50V J CH<HR,HT>
C943 87-010-197-080 CAP, CHIP 0.01-25 K B<HR,HT>
C945 87-010-197-080 CAP, CHIP 0.01-25 K B<HR,HT>
C946 87-010-971-080 C-CAP,S 4700P-50 J B<HR,HT>
C947 87-010-197-080 CAP, CHIP 0.01-25 K B<HR,HT>
C948 87-010-148-080 CAP, CHIP S 4P-50<HR,HT>
C952 87-010-197-080 CAP, CHIP 0.01 DM<HR,HT>
C953 87-010-197-080 CAP, CHIP 0.01 DM<HR,HT>
C954 87-010-400-080 CAP, ELECT 0.47-50V<HR,HT>
C956 87-010-263-080 CAP, ELECT 100-10V<HR,HT>
C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C960 87-010-196-080 CHIP CAPACITOR,0.1-25<LH,HS>
C961 87-010-152-080 C-CAP,S 8P-50 CH<LH,HS>
C962 87-010-401-080 CAP, ELECT 1-50V<HR,HT>
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C964 87-010-854-080 C-CAP,S 560PCH<HR,HT>
C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V
C973 87-010-197-080 CAP, CHIP 0.01-25 K B
C974 87-010-197-080 CAP, CHIP 0.01-25 K B
C979 87-010-322-080 C-CAP,S 100P-50 CH
C981 87-010-260-080 CAP, ELECT 47-25V
C982 87-010-196-080 CHIP CAPACITOR,0.1-25
C983 87-010-197-080 CAP, CHIP 0.01-25 K B
C984 87-010-197-080 CAP, CHIP 0.01-25 K B
C987 87-010-197-080 CAP, CHIP 0.01-25 K B
C989 87-010-197-080 CAP, CHIP 0.01-25 K B<HR,HT>
C991 87-010-312-080 C-CAP,S 15P-50 CH
C992 87-010-312-080 C-CAP,S 15P-50 CH
C993 87-010-178-080 CHIP CAP 1000P-50 K B
C995 87-010-178-080 CHIP CAP 1000P-50 K B
C997 87-010-196-080 CHIP CAPACITOR,0.1-25
C998 87-010-260-080 CAP, ELECT 47-25V
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-261-010 FILTER, SFE10.7MA5-A
CF832 87-008-261-010 FILTER, SFE10.7MA5-A
CN301 87-A60-620-010 CONN,3P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-A60-131-010 CONN,6P V FE
CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480)
CON351 86-ZM3-605-110 CON ASSY,8P-PB
D951 87-A40-618-080 VARI-CAP,SVC 348(S/T)<HR,HT>
FC602 88-906-251-110 FF-CABLE,6P 1.25
FFE831 A8-8ZA-195-030 8ZA-1 YFEMUNM<LH>
FFE831 A8-8ZA-194-030 8ZA-1 FEMUNM<HR,HS,HT>
J202 87-A60-488-010 JACK,DIA6.3 BLK ST W/SW KM16AT
J203 87-A60-238-010 TERMINAL,SP 4P (MSC)
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
PART NO.
NO.
– 5 –
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02
J940 87-A60-633-010 CONN,2P H 2.5MM JMT<HR,HT>
L101 87-A50-610-010 COIL,1UH K(MDEC)
L102 87-A50-610-010 COIL,1UH K(MDEC)<HS,HR>
L451 87-007-342-010 COIL,OSC 85K BIAS
L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)<LH,HS>
L802 87-A91-552-010 FLTR,CFMT-450AL (TOK)<HR,HT>
L811 87-005-847-080 COIL,2.2UH(CECS)
L832 87-005-847-080 COIL,2.2UH(CECS)
L941 87-A50-022-010 COIL,ANT SW 7.96(COI) MHZ<HR,HT>
L942 87-A50-550-010 COIL,OSC SW-2N(COI)<HR,HT>
L943 87-A50-522-080 COIL,1MH K CEC<HR,HT>
L944 87-A50-159-010 COIL,10MH K C2B<HR,HT>
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<LH,HS>
L952 87-A50-430-010 COIL,ANT MW(3BSW)<HR,HT>
L953 87-A50-431-010 COIL,OSC MW(3BSW)<HR,HT>
R129 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R129 87-A00-257-080 RES,M/F 0.15-1W J<HR,HS,HT>
R130 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R130 87-A00-257-080 RES,M/F 0.15-1W J<HR,HS,HT>
R131 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R131 87-A00-257-080 RES,M/F 0.15-1W J<HR,HS,HT>
R132 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R132 87-A00-257-080 RES,M/F 0.15-1W J<HR,HS,HT>
R143 87-A00-440-050 RES,220-1/2W J RP
R144 87-A00-440-050 RES,220-1/2W J RP
R145 87-A00-440-050 RES,220-1/2W J RP
R146 87-A00-440-050 RES,220-1/2W J RP
R653 87-A11-144-080 CAP,TC U 0.1-50 K B
R654 87-A11-144-080 CAP,TC U 0.1-50 K B
R790 87-010-197-080 CAP, CHIP 0.01 DM
R991 87-010-322-080 C-CAP,S 100P-50 CH
R993 87-010-322-080 C-CAP,S 100P-50 CH
R995 87-010-322-080 C-CAP,S 100P-50 CH
SFR451 87-A90-433-080 SFR,50K H NVZ6TLTA
SFR452 87-A90-433-080 SFR,50K H NVZ6TLTA
TC941 87-A91-773-080 TRIMMER,PLY 20P 6.8x5.4 CDYL<HR,HT>
TC943 87-A91-774-080 TRIMMER,PLY 30P 6.8x5.4 CDYL<HR,HT>
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
FRONT C.B
C101 87-010-196-080 CHIP CAPACITOR,0.1-25
C102 87-010-196-080 CHIP CAPACITOR,0.1-25
C103 87-010-498-040 CAP,E 10-16 M 5L
C104 87-010-196-080 CHIP CAPACITOR,0.1-25
C107 87-010-493-040 CAP,E 0.47-50 M 5L
C108 87-012-393-080 C-CAP,S 0.22-16 R K
C153 87-010-198-080 CAP, CHIP 0.022-25 K B
C154 87-010-246-040 CAP,E 47-35 SME
C155 87-010-404-040 CAP,E 4.7-50 SME
C156 87-010-404-040 CAP,E 4.7-50 SME
C361 87-010-178-080 CHIP CAP 1000P-50 K B
C362 87-010-178-080 CHIP CAP 1000P-50 K B
C371 87-010-178-080 CHIP CAP 1000P-50 K B
C372 87-010-178-080 CHIP CAP 1000P-50 K B
C401 87-010-186-080 CAP,CHIP 4700P<HR,HS,HT>
C402 87-010-112-040 CAP,E 100-16<HR,HS,HT>
C403 87-010-545-040 CAP,E 0.22-50 SME<HR,HS,HT>
C404 87-010-320-080 CHIP CAP 68P<HR,HS,HT>
C405 87-010-544-040 CAP,E 0.1-50 SME<HR,HS,HT>
C406 87-010-544-040 CAP,E 0.1-50 SME<HR,HS,HT>
C407 87-010-405-040 CAP,E 10-50<HR,HS,HT>
C408 87-010-322-080 C-CAP,S 100P-50 CH<HR,HS,HT>
C409 87-010-265-040 CAP,E 33-16 SME<HR,HS,HT>
C410 87-012-369-080 C-CAP,S 0.047-50F<HR,HS,HT>
DESCRIPTIONREF. NO. KANRI
C413 87-010-177-080 C-CAP,S 820P-50 SL<HR,HS,HT>
C601 87-010-382-040 CAP,E 22-25 SME
C801 87-010-195-080 C-CAP,S 0.068-25 F
C802 87-010-195-080 C-CAP,S 0.068-25 F
C803 87-010-402-040 CAP,E 2.2-50 SME
C804 87-010-402-040 CAP,E 2.2-50 SME
C805 87-010-196-080 CHIP CAPACITOR,0.1-25
C806 87-010-196-080 CHIP CAPACITOR,0.1-25
C810 87-010-379-040 CAP,E 22-16 M 11L SME
C901 87-010-322-080 C-CAP,S 100P-50 CH
C902 87-010-322-080 C-CAP,S 100P-50 CH
C903 87-010-322-080 C-CAP,S 100P-50 CH
C904 87-010-322-080 C-CAP,S 100P-50 CH
C905 87-010-322-080 C-CAP,S 100P-50 CH
C906 87-010-322-080 C-CAP,S 100P-50 CH
C907 87-010-322-080 C-CAP,S 100P-50 CH
C908 87-010-322-080 C-CAP,S 100P-50 CH
C909 87-010-322-080 C-CAP,S 100P-50 CH
C910 87-010-322-080 C-CAP,S 100P-50 CH
C911 87-010-178-080 CHIP CAP 1000P-50 K B
C912 87-010-196-080 CHIP CAPACITOR,0.1-25
C913 87-010-248-040 CAP,E 220-10 SME
C914 87-010-248-040 CAP,E 220-10 SME
C915 87-010-196-080 CHIP CAPACITOR,0.1-25
C916 87-010-196-080 CHIP CAPACITOR,0.1-25
C917 87-010-196-080 CHIP CAPACITOR,0.1-25
C919 87-010-197-080 CAP, CHIP 0.01-25 K B
C920 87-012-369-080 C-CAP,S 0.047-50F
C921 87-010-186-080 CAP,CHIP 4700P-50 K B
C951 87-010-312-080 C-CAP,S 15P-50 CH
C952 87-012-155-080 C-CAP 180P-50CH
C953 87-012-140-080 CAP 470P-50 CH
C961 87-010-378-040 CAP,E 10-16 M SME
C962 87-012-157-080 C-CAP,S 330P-50 CH
C963 87-010-196-080 CHIP CAPACITOR,0.1-25
CN104 87-A60-057-010 CONN,11P V 9604S-11C
CN701 87-099-720-010 CONN,30P BLK TYK-B(P)
CN731 87-099-015-010 CONN,13P V BLK 6216V
EMI401 87-008-372-080 FILTER, EMI BL OIRNI<HR,HS,HT>
FC104 88-911-101-110 FF-CABLE,11P 1.25
FC731 88-913-301-110 FF-CABLE,13P-1.25
FL901 8A-NF9-605-010 FL,HNA-10SS12
J401 87-A61-243-010 JACK,6.3 BLK MONO W/SW V<HR,HS,HT>
L951 87-A50-434-010 COIL,CLK 4.19M(TOKO)
LED201 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED202 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED203 87-A40-619-040 LED,SLR-56PT-T31-W GRN<HR,HS,HT>
LED204 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED205 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED206 87-A40-619-040 LED,SLR-56PT-T31-W GRN<HR,HS,HT>
LED209 87-A40-317-080 LED,SLR-342VCT31 RED
LED210 87-A40-619-040 LED,SLR-56PT-T31-W GRN<LH>
S301 87-A90-164-080 SW,TACT SKQNAB(N)
S302 87-A90-164-080 SW,TACT SKQNAB(N)
S303 87-A90-164-080 SW,TACT SKQNAB(N)
S304 87-A90-164-080 SW,TACT SKQNAB(N)
S305 87-A90-164-080 SW,TACT SKQNAB(N)
S306 87-A90-164-080 SW,TACT SKQNAB(N)
S307 87-A90-164-080 SW,TACT SKQNAB(N)
S308 87-A90-164-080 SW,TACT SKQNAB(N)
S309 87-A90-164-080 SW,TACT SKQNAB(N)
S321 87-A90-164-080 SW,TACT SKQNAB(N)
S322 87-A90-164-080 SW,TACT SKQNAB(N)
S323 87-A90-164-080 SW,TACT SKQNAB(N)
S324 87-A90-164-080 SW,TACT SKQNAB(N)
S325 87-A90-164-080 SW,TACT SKQNAB(N)
S326 87-A90-164-080 SW,TACT SKQNAB(N)
S341 87-A90-164-080 SW,TACT SKQNAB(N)
S342 87-A90-164-080 SW,TACT SKQNAB(N)
S343 87-A90-164-080 SW,TACT SKQNAB(N)
PART NO.
NO.
– 6 –
PART NO. DESCRIPTIONREF. NO. KANRI
S344 87-A90-164-080 SW,TACT SKQNAB(N)
S345 87-A90-164-080 SW,TACT SKQNAB(N)
S346 87-A90-164-080 SW,TACT SKQNAB(N)
S347 87-A90-164-080 SW,TACT SKQNAB(N)
S348 87-A90-164-080 SW,TACT SKQNAB(N)
S349 87-A90-164-080 SW,TACT SKQNAB(N)
S350 87-A90-164-080 SW,TACT SKQNAB(N)
S361 87-A91-633-010 SW,RTRY XRE012103PVB25FINA 1-2
S371 87-A91-632-010 SW,RTRY XRE012103PVB25FINB 1-2
VR401 86-NFA-607-010 VR,RTRY 10K15AX1 1V XV0121PVN<HR,HS,HT>
PT C.B
C1 87-010-387-080 CAP,E 470-25 SME
C31 87-010-403-080 CAP, ELECT 3.3-50V
CN1 87-A61-110-010 CONN,9P V TID-A
PT1 8A-NF9-711-010 PT,ANF-9H-LOW VA<HR,HS,HT>
!
!
PT1 8A-NF9-712-010 PT,ANF-9H-HI VA<LH>
!
PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI
!
RY1 87-A91-339-010 RELAY,AC DC12V G5PA-2
!
S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<LH,HR,HT>
!
T1 87-A60-317-010 TERMINAL, 1P MSC
!
T2 87-A60-317-010 TERMINAL, 1P MSC
DECK C.B<LH>
CN1 87-099-753-010 CONN,11P 9604
SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY, 27
SOL2 82-ZM1-618-410 SOL ASSY, 27
SW1 87-A90-673-010 SW,MICRO ESE11SH1C
NO.
DESCRIPTIONREF. NO. KANRI
SW2 87-A91-500-010 SW,MICRO MPU11470MLB0
SW3 87-A91-500-010 SW,MICRO MPU11470MLB0
SW4 87-A91-500-010 SW,MICRO MPU11470MLB0
SW5 87-A90-673-010 SW,MICRO ESE11SH1C
DECK C.B<HR,HS,HT>
CON105 87-099-753-010 CONN,11P H 9604
M1 87-045-347-010 MOT,SHU2L 70
SFR1 87-024-581-010 SFR,3.3K DIA6V K0A
SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW4 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW5 87-A90-248-010 SW,MICRO ESE11SH2CXQ
HEAD-1 C.B<HR,HS,HT>
CON301 85-MA2-615-010 CONN,ASSY 3P-PB
PART NO.
NO.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
– 7 –
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
TRANSISTOR ILLUSTRATION
E C B
CD1585BC
CSA952K
KTA1266GR
KTC3198GR
S
D
G
2SK360E
E C B
2SC5343G
CC5551
S D G
2SK2541
E B C
2SA1981Y
G
S
2SK21582SJ460
E C B
CSC4115BC
D
B
2SA1235F
2SC2714(O)
2SC3052F
CMBT5401
CMBT5551
C
E
CSD1306E
KRC102S-RTK
KRC104S
RT1P141C
RT1P144C
B C E
2SB1228
2SB1370E
2SB1686
2SD1830
2SD2642
G D S
2SK2937
E C B
DTC114ES
KTC3199GR
– 8 –
WIRING 1 (MAIN) <LH, HS>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
9
R
S
T
U
WIRING 2 (MAIN) <HR, HT>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
10
R
S
T
U
SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2 : AMP)
– 11 –
SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2 : TUNER) <LH,HS>
– 12 –
SCHEMATIC DIAGRAM – 3 (MAIN 2 / 2 : TUNER) <HR,HT>
– 13 –
WIRING 3 (FRONT)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
14
R
S
T
U
SCHEMATIC DIAGRAM – 4 (FRONT)
– 15 –
WIRING 4 (PT)
151413121110987654321
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
R
S
T
U
SCHEMATIC DIAGRAM – 5 (PT)
– 17 –
WIRING 5 (DECK : ZZM-3 PR1NF) <LH>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
TO FRONT C.B CN104
D DECK C.B
SW5
(CAM2)
IC2
1
3
SW4
(CST2)
SFR1
(FC104)
1 3 5 7 9 11
2 4 6 8 10
CN1
SOL2
R1
SW3
(REA)
C
D
SW2
H
L
+
(CST1)
IC1
1
3
SOL1
SW1
E
(CAM1)
F
G
H
I
W1
+
H
L
M1
DECK
MOTOR
J
K
L
M
N
O
P
Q
R
S
T
18
U
WIRING 6 (DECK / HEAD 1 : 6ZM-3 PR2NM) <HR,HS,HT>
151413121110987654321
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
19
R
S
T
U
IC BLOCK DIAGRAM
– 20 –
ADJUSTMENT <TUNER / DECK / FRONT>
< TUNER SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to AM 1710kHz(LH), AM 1602kHz(HS),
MW 1602kHz(HR,HT) and check that the test point is
2160kHz ± 45Hz(LH), 2052kHz ± 45Hz(HR,HS,HT).
2. AM VT Check<LH,HS>
Settings : • Test point : TP1 (VT)
Method : Set to AM 1710kHz(LH), AM 1602kHz(HS) and check
that the test point is less than 8.5V(LH), less than
8.0V(HS). Then set to AM 530kHz(LH), AM 531kHz(HS)
and check that the test point is more than 0.6V.
3. MW VT Adjustment <HR,HT>
Settings : • Test point : TP1 (VT)
• Adjustment location : L953
Method : Set to MW 1602kHz and adjust L953 so that the test point
becomes 8.5V ± 0.05V. Then set to MW 531kHz and
check that the test point is more than 0.3V.
4. SW VT Adjustment <HR,HT>
Settings : • Test point : TP1 (VT)
• Adjustment location : L942
Method : Set to SW 17.9MHz and adjust L942 so that the test point
becomes 8.0V ± 0.05V. Then set to SW 5.73MHz and
check that the test point is more than 0.3V.
10. AM IF Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L802 ................................................ 450kHz
11. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance)
TP8(Lch), TP9(Rch) (Distortion)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the voltage
between TP3 and TP4 becomes 0V ± 300mV, with
minimum distortion.
5. FM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to FM 87.5MHz, 108.0MHz and check that the test
point is more than 0.5V (87.5MHz) and less than 8.0V
(108.0MHz).
6. AM Tracking Adjustment<LH,HS>
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location : L951(1/3)
Method : Set to AM 1000kHz and adjust L951(1/3) to MAX.
7. MW Tracking Adjustment <HR,HT>
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L952 ..........................................................603kHz
TC941 .....................................................1404kHz
Method : Set up TC941 to center before adjustment. Adjust L952
so that the level at 603kHz becomes maximum. Then
adjust TC941 so that the level at 1404kHz becomes
maximum.
8. SW Tracking Adjustment <HR,HT>
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L941 ..........................................................5.9MHz
TC943 ......................................................17.9MHz
Method : Set up TC943 to center before adjustment. Adjust L941
so that the level at 5.9MHz becomes maximum. Then
adjust TC943 so that the level at 17.9MHz becomes
maximum.
9. FM Tracking Check
Settings : • Test point : TP8(Lch), TP9(Rch)
Method : Set to FM 83.0MHz(LH,HS), FM 98.0MHz(HR,HT)
and check that the test point is less than 10dBµV(LH,HS),
less than 9dBµV(HR,HT).
– 21 –
< DECK SECTION >
< FRONT SECTION >
12. Tape Speed Adjustment (DECK 2)
Settings : • Test tape : TTA–100
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz ± 5Hz (FWD) and
FWD SPEED ± 45Hz (REV).
13. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : Azimuth adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape and
adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
14. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
Method : Play back the 315Hz and 8kHz signals of the test tape
and check that the output ratio of the 8kHz signal with
respect to that of the 315Hz signal is within 5.0dB.
15. PB Sensitivity Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–200
• Test point : TP8(Lch), TP9(Rch)
Method : Play back the test tape and check that the output level of
the test point is 110mV ± 3.0dB.
18. µ-CON OSC Adjustment
Settings : • Test point : TP11 (KEY-SCAN), (GND)
• Adjustment location : L951
Method : Connect a frequency counter across TP11 (KEY-SCAN)
and GND. Insert AC plug while pressing POWER key
and TUNER function key. Then adjust L951 so that the test
point becomes 92.470Hz ± 0.092Hz. To manual reset,
press POWER key while pressing CLEAR key.
16. REC/PB Frequency Response Adjustment (DECK 2)
Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz / 8kHz (LINE IN)
• Adjustment location : SFR451 (Lch)
SFR452 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the TP8, TP9
becomes -20VU (-26dBV). Record and play back the
1kHz and 8kHz signals and adjust SFRs so that the
output of the 8kHz signals becomes -1.5dB ± 0.5dB with
respect to that of the 1kHz signal.
17. REC/PB Sensitivity Check (DECK 2)
Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at TP8, TP9 becomes
0VU (-6dBV). Record and play back the 1kHz signals
and check that the output is -1dB ± 3.5dB.
– 22 –
MECHANICAL EXPLODED VIEW 1 / 1
G
15
17
9
LH: AZG-1 YKZD3RDF
HR,HS,HT: AZG-1 ZD3RDM
A
A
PWB
WIRE,
BINDER
32
A
A
A
A
A
C
18
21
16
19
FL901
22
23
24
B
20
30
31
A
A
29
A
HT-SINK
25
A
G
H
45
A
A
44
33
PWB
SH,PT20-16-1
W/ADH
42
E
5
11
3
6
1
7
C
27
28
9
12
13
8
4
14
D
PLATE,EARTH MECH
10
36
37
34
26
38
382
37
35
39
PWB
F
A
A
LH: ZZM-3 PR1NF
HR,HS,HT: 6ZM-3 PR2NM
H
40
A
CHAS,MAIN
41
A
43
G
– 23 –
MECHANICAL PARTS LIST 1 / 1
PART NO.
NO.
1 8A-NF9-006-010 WINDOW,CASS 1
2 8A-NF9-007-010 WINDOW,CASS 2
3 8A-NF9-003-010 BOX,CASS 1<LH>
3 8A-NF9-047-010 BOX,CASS H<EXCEPT LH>
4 8A-NF9-004-010 BOX,CASS 2
5 8A-NF8-207-010 SPR-T,EJECT 1
6 8A-NF8-208-010 SPR-T,EJECT 2
7 87-CE3-023-010 BADGE,AIWA 30N SILV
8 8A-NF9-018-010 KNOB,RTRY JOG
9 8A-NF8-209-010 OIL-DMPR,120
10 8A-NF9-017-010 PANEL,JOG
11 8A-NF9-016-010 KNOB,RTRY VOL
12 8A-NF9-015-010 KNOB,RTRY MIC<EXCEPT LH>
13 81-532-080-010 LABEL, CASS. COMPT
14 8A-NFX-006-010 CABI,FR H<EXCEPT LH>
14 8A-NF9-001-010 CABI,FR U<LH>
15 8A-NFX-002-010 WINDOW,DISP LH
16 8A-NF9-039-010 WINDOW,CD
17 8A-NF8-007-010 PANEL,LEFT V-2
18 8A-NF8-005-010 PANEL,TOP
19 8A-NF8-006-010 WINDOW,TOP
20 8A-NF9-014-010 PANEL,TRAY
21 8A-NF9-008-010 KEY,POWER
22 8A-NF9-009-010 KEY,FUN
23 8A-NF9-022-010 REFLECTOR,ECO
24 8A-NF9-010-110 KEY,ASSY OPE 1 WAY<LH>
24 8A-NF9-023-010 KEY,ASSY OPE REW<EXCEPT LH>
25 8A-NF9-020-110 KEY,CD
26 8A-NF9-019-010 KEY,SYNC
27 8A-NF9-026-110 KEY,ENTER
28 8A-NF9-021-010 PLATE,MIC<EXCEPT LH>
29 8A-NF9-201-010 GUIDE,OPE 1 WAY<LH>
29 8A-NF9-203-010 GUIDE,OPE REV<EXCEPT LH>
30 82-NF7-210-110 GUIDE,FL (*)
31 8A-NF8-206-010 HLDR,PWB M
DESCRIPTIONREF. NO. KANRI
PART NO.
32 88-906-251-110 FF-CABLE,6P 1.25
33 8A-NF9-211-010 HLDR,PWB PT HI
34 88-913-301-110 FF-CABLE,13P-1.25
35 88-911-101-110 FF-CABLE,11P 1.25
36 87-NF4-216-010 HLDR,LOCK 1
37 86-NF9-224-010 SPR-C,LOCK
38 82-NF5-229-010 PLATE,LOCK
39 87-NF4-217-110 HLDR,LOCK 2
40 87-NF4-221-010 HLDR,CABLE
41 87-085-185-010 BUSHING, AC CORD (E)
42 87-A80-155-010 AC CORD ASSY HS,TS<HS>
!
42 87-A80-157-010 AC CORD ASSY,E BLK CC<EXCEPT HS>
!
43 8A-NF8-008-010 PANEL,RIGHT V-2
44 8A-NFX-018-010 CABI,REAR HR W/O SPEC<HT>
44 8A-NFX-003-110 CABI,REAR HRJSM<HR>
44 8A-NFX-008-110 CABI,REAR HS W/O SPEC<HS>
44 8A-NFX-004-110 CABI,REAR LHFD<LH>
45 84-ZG1-245-210 CAP,OPTICAL
A 87-067-703-010 TAPPING SCREW, BVT2+3-10
B 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
C 87-721-097-410 QT2+3-12 GLD
D 87-067-689-010 TAPPING SCREW, BVTT+3-8
E 87-723-096-410 QT2+3-10W/O SLOT BL
F 87-721-096-410 QT2+3-10 GLD
G 87-067-641-010 UTT2+3-8(W/O SLOT)BL
H 87-078-200-010 S-SCREW,ITC+4-8 R
NO.
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green
– 24 –
TAPE MECHANISM EXPLODED VIEW 1 / 1 <ZZM-3 PR1NF>
TERMINAL,
LB1
33
31
AA
34
32
30
21
20
19
55
35
28
27
26
25
24
29
37
39
38
36
41
40
43
42
44
52
33
31
21
20
41
44
45
46
51
b
53
47
48
49
50
52
51
43
42
40
b
45
46
47
a
a
48
49
B
A
TERMINAL,LB1
32
35
30
29
28
27
26
25
23
18
22
5
6
14
10
11
15
7
16
9
1
2
6
10
11
8
5
3
c
14
9
17
16
19
IC, EW732
18
54
38
39
37
PWB
12
24
23
22
IC, EW732
54
c
12
13
4
– 25 –
15
13
TAPE MECHANISM PARTS LIST 1 / 1 <ZZM-3 PR1NF>
PART NO.
NO.
1 8Z-ZM3-227-010 BELT,MAIN M3
2 8Z-ZM3-235-010 BELT,MAIN L
3 8Z-ZM1-235-010 PULLEY,MOT
4 87-045-347-010 MOT,SHU2L 70
5 8Z-ZM1-232-010 GEAR,IDL FF/REW
6 8Z-ZM3-244-010 GEAR,CAM TD20
7 8Z-ZM3-256-010 FLY-WHL ASSY,M3 R
8 8Z-ZM3-255-010 FLY-WHL ASSY,M3 L
9 8Z-ZM3-231-010 SPR-T,TRIG
10 8Z-ZM3-213-010 CLR,MG
11 82-ZM3-616-010 RING MAGNET 4
12 8Z-ZM3-243-010 LEVER ASSY,HD UP
13 8Z-ZM3-238-010 SPR-T,HD UP
14 8Z-ZM3-219-010 GEAR,CAM M3
15 8Z-ZM3-206-010 LEVER,TRIG
16 8Z-ZM3-209-010 LEVER,CAM FR
17 8Z-ZM3-203-010 CHAS ASSY,M3
18 8Z-ZM1-228-010 GEAR,SLIP T-UP B
19 8Z-ZM1-265-010 FELT,T-UP
20 8Z-ZM1-227-010 GEAR,SLIP T-UP A
21 8Z-ZM1-251-110 SPR-C,T-UP SLIP
22 8Z-ZM1-275-010 W-L,1,47-4-0.25
23 8Z-ZM1-257-010 SPR-C,F/R
24 8Z-ZM1-236-010 CLR,SLIP FF/REW
25 8Z-ZM3-226-010 SPR-C,FR M3
26 8Z-ZM3-250-010 GEAR,SLIP F/R A M3
27 8Z-ZM1-269-010 FELT,FF/REW 2
28 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
29 8Z-ZM3-220-010 LEVER,FR M3
30 8Z-ZM3-205-010 LEVER,PLAY M3
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
31 8Z-ZM3-233-010 SPR-T,BRG M3
32 84-ZM2-227-310 SPR-C,AZIMUTH
33 87-A90-403-110 HEAD,RPH MS15R
34 87-A90-404-010 HEAD,EH LE15B
35 8Z-ZM3-239-010 SPR-E,FR
36 8Z-ZM3-211-010 LEVER,EJECT R
37 8Z-ZM3-225-010 LEVER,STOP
38 8Z-ZM3-221-010 LEVER,CAS
39 8Z-ZM3-234-010 SPR-T,LVR CAS
40 8Z-ZM3-223-010 SPR-C,REEL R M3
41 8Z-ZM1-225-110 GEAR,REEL R
42 8Z-ZM3-240-010 SPR-T,T-UP M3
43 8Z-ZM3-237-010 SPR-T,PINCH M3
44 8Z-ZM3-215-010 LEVER,PINCH M3
45 8Z-ZM1-261-110 ROLLER ASSY,PINCH
46 8Z-ZM1-226-010 GEAR,REEL L
47 8Z-ZM3-222-010 SPR-C,REEL L M3
48 8Z-ZM3-251-010 GEAR,IDL REW M3
49 8Z-ZM3-236-010 SPR-T,PLAY M3
50 82-ZM1-240-110 LVR,REC(*)
51 8Z-ZM3-216-010 LEVER,T-UP M3
52 87-B10-301-010 W-L,1.63-3.2-05 SLIT
53 8Z-ZM3-212-010 LEVER,EJECT L
54 8Z-ZM3-214-010 HLDR,IC
55 86-ZM3-605-110 CONN ASSY,8P -RPB
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM2-220-110 V+2.6 ZZM-2
DESCRIPTIONREF. NO. KANRI
– 26 –
TAPE MECHANISM EXPLODED VIEW 1 / 1 <6ZM-3 PR2NM>
PWB
e
38
56
25
24
23
PLATE, SHLD
M3
22
26
27
SH, 1.63-3.2
-0.5 SLT
28
29
LVR EJECT L
30
J
31
45
G
44
35
32
34
e
33
M
36
37
L
30
33
J
b
32
34
43
58
42
41
35
36
31
H
47
48
40
46
41
49
55
50
F
B
D
C
A
51
52
14
53
47
58
GEAR PLAY
13
38
39
57
LVR EJECT R
4
a
60
10
8
N
d
c
GEAR
11
16
PLAY
12
17
c
d
9
4
13
59
E
18
54
3
2
4
15
7
6
11
54
a
b
27
9
10
12
21
K
7
4
1
2
6
3
5
I
19
MOTOR
20
– 27 –
PWB
8
60
I
TAPE MECHANISM PARTS LIST 1 / 1 <6ZM-3 PR2NM>
PART NO.
NO.
1 82-ZM1-234-310 FLY-WHL,L ASSY
2 82-ZM3-305-310 GEAR,CAM M2(*)
3 82-ZM1-226-010 GEAR,REW
4 82-ZM1-216-510 GEAR,REEL
5 09-001-420-010 FLY-WHL,R ASSY
6 82-ZM1-225-210 GEAR,FR
7 82-ZM3-306-110 LVR,FR M2
8 82-ZM3-333-310 SLIP DISK ASSY 2
9 82-ZM1-322-010 SPR-T,FR 60
10 82-ZM1-220-210 GEAR,IDLER
11 82-ZM3-616-010 RING MAGNET 4
12 82-ZM1-227-310 LVR,TRIG
13 82-ZM1-265-310 SPR-E,TRIG
14 86-ZM3-219-010 PLATE,SPACER 0.1
15 82-ZM1-237-610 FLY-WHL ASSY,RW
16 86-ZM3-210-010 BELT,PS
17 82-ZM3-221-210 PULLEY,MOT 2M 3
18 86-ZM3-203-010 HLDR,MOT S
19 86-ZM1-206-010 BELT,MAIN L
20 82-ZM3-627-010 SOL ASSY,27 SO
21 82-ZM3-335-310 PULLEY,COUPLER M3
22 86-ZM3-215-110 CHAS ASSY,RS
23 82-ZM1-258-210 SPR-T,PINCH L
24 82-ZM1-341-210 LVR ASSY,PINCH L2
25 82-ZM1-266-310 LVR,DIR
26 82-ZM1-214-010 SPR-T,DIR
27 82-ZM1-333-210 PLATE,LINK2
28 82-ZM3-339-110 SHAFT,COUPLER N3
29 82-ZM1-255-310 SPR-E,LVR DIR
30 82-ZM1-285-410 SPR-C,BT L
31 82-ZM1-222-310 LVR,PLAY
32 82-ZM1-217-410 REEL TABLE
33 82-ZM1-244-510 SPR-C,BT
34 82-ZM1-257-010 SPR-T,CAS
35 82-ZM1-242-010 LVR,CAS
36 82-ZM1-243-010 LVR,STOP
37 82-ZM1-240-110 LVR,REC(*)
38 82-ZM1-344-110 LVR ASSY,PINCH R2
39 86-ZM3-204-010 SPR-T,PINCH S
40 82-ZM1-208-310 HLDR,HEAD
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
41 82-ZM1-219-110 SPR-T,LINK
42 82-ZM1-210-110 GEAR,H T
43 82-ZM3-353-010 SPR-T,HEAD
44 82-ZM1-207-910 GUIDE,TAPE
45 82-ZM1-314-110 PLATE,HEAD
46 87-A90-366-110 HEAD,PH YK50P-BF414 FPC
47 82-ZM1-218-010 SPR-E,HB
48 82-ZM1-206-910 CHAS,HEAD
49 86-ZM3-206-010 SPR-C,EH S
50 87-A90-404-010 HEAD,EH LE15B
51 87-A90-403-110 HEAD,RPH MS15R
52 86-ZM3-205-110 SPR-C,RPH S
53 86-ZM3-202-210 BASE,HEAD S
54 82-ZM1-245-210 HLDR,IC
55 86-ZM3-605-110 CONN ASSY,8P -RPB
56 82-ZM1-259-210 SPR-T,PINCH R
57 86-ZM3-201-010 CHAS,HEAD S
58 82-ZM1-269-210 SPR-T,BRG
59 86-ZM3-214-110 BELT,SBU RR
60 82-ZM1-338-110 BELT,FR 4
A 86-ZM3-207-010 S-SCREW,RPH
B 86-ZM3-209-010 S-SCREW,AZIMUTH S
C 86-ZM3-218-110 S-SCREW,EH 2
D 86-ZM3-208-110 S-SCREW,EH
E 87-251-071-410 U+2.6-4
F 80-ZM6-207-010 V+1.6-7
G 86-ZM4-206-010 S-SCREW,AZIMUTH L
H 85-ZM3-202-010 S-SCREW,TG
I 82-ZM3-334-010 PW 2.16-6-0.4
J 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT
K 87-B10-043-010 W-P,0.99-4-0.25 SLT
L 86-ZM3-213-010 S-SCREW,HLDR MOT S
M 87-761-073-410 VFT2+2.6-8 W/O SLOT
N 82-ZM3-222-010 S-SCREW,SHILD PLATE
DESCRIPTIONREF. NO. KANRI
– 28 –
SPEAKER PARTS LIST
SX-NSZ52(YJSL,YJSC,YLSL,Y1SL,Y1SL)
PART NO.
NO.
1 8A-NSJ-001-010 PANEL,FR R<EXCEPT YJSC>
1 8A-NSJ-026-010 PANEL,FR R F<YJSC>
2 8A-NSJ-002-010 PANEL,FR L<EXCEPT YJSC>
2 8A-NSJ-027-010 PANEL,FR L F<YJSC>
3 8A-NSJ-003-010 GRILLE,FRAME ASSY<EXCEPT YJSC>
3 8A-NSJ-028-010 GRILLE,FRAME ASSY F<YJSC>
4 8A-NSJ-008-010 PROTECTOR,TWA<EXCEPT YJSC>
4 8A-NSJ-032-010 PROTECTOR,TW F<YJSC>
5 8A-NSJ-602-010 SPKR,W 130<EXCEPT YJSC>
5 8A-NSJ-604-010 SPKR,W 140<YJSC>
6 88-NS5-605-010 SPKR,T 60<EXCEPT YJSC>
6 8A-NSJ-606-010 SPKR,T 60<YJSC>
7 88-MS1-608-010 SPKR,CERAMIC
8 87-NS7-611-010 CORD,SPKR
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
1 8A-NF9-902-110 IB,LH(ESP)M<LH>
1 8A-NFX-901-110 IB,H(ECA)M-30<HR,HT>
1 8A-NFX-935-010 IB,HS(K)<HS>
2 87-043-115-010 FEEDER-ANT FM
3 87-006-268-010 ANT LOOP AM<LH>
3 87-006-226-010 ANT LOOP AM<HR,HT>
3 87-006-225-010 AM,LOOP ANT NC2<HS>
4 87-A90-119-010 ANT,WIRE SW (5M)<HR,HT>
5 8Z-NF9-701-210 RC UNIT,ZAS02<LH>
5 8Z-NF8-701-210 RC UNIT,ZAS01<HR,HS,HT>
6 87-A91-017-010 PLUG CONVERSION, JT-0476<LH,HR,HT>
!
NO.
DESCRIPTIONREF. NO. KANRI
– 29 –
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9820543 0251431
Loading...