Page 1
CSD-A310
LH, HA, K
SERVICE MANUAL
COMPACT DISC STEREO
RADIO CASSETTE RECORDER
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
CSD-A310 (LH, HA), (S/M Code No. 09-003-428-2T1) and CSD-A310 (K),
(S/M Code No. 09-003-428-2T2).
BASIC TAPE MECHANISM : TN-21ZVC-2000
BASIC CD MECHANISM : DA11T3C
S/M Code No. 09-005-428-2R1
REVISION
DATA
Page 2
SPECIFICATIONS
<Tuner section>
Frequency range FM: 87.5 MHz to 108.0 MHz
Antenna: Rod antenna
AM (MW):
530 kHz to 1,750 kHz <LH, HA>
530 kHz to 1,605 kHz <K>
Antenna: Ferrite bar antenna
LW: <K>
150 kHz to 285 kHz
Antenna: Ferrite bar antenna
<Deck section>
Track format 4 tracks, 2 channels
Frequency range Normal tape: 50 - 12,500 Hz (EIAJ)
Recording system AC bias
Erasing system Magnet erase
Heads Recording/playback head (1)
Erasure head (1)
<CD player section>
Disc Compact disc
Scanning method Non-contact optical scanner
(semiconductor laser)
<General>
Speaker 80 mm cone type (2)
Outputs Headphones jack: stereo mini-jack
Power output 2.5 W + 2.5 W
(EIAJ 7 ohms, T.H.D. 10 %)
1.9 W + 1.9 W
(DIN 1% Rated Power)
Power requirements DC 12 V using eight size C (R14)
batteries
AC 110 - 120 V/220 - 240 V
switchable, 50/60 Hz <LH, HA>
AC 230 V, 50 Hz <K>
Power consumption 16 W
Dimensions 310 x 171 x 260 mm
(W x H x D)
Weight 2.8 kg (excluding batteries)
• Design and specifications are subject to change without
notice.
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved å bning,
nå r sikkerhedsafbrydere er ude af funktion.
Undgå udsæ ttelse for strå ling.
VAROITUS!
Laiteen Kä yttä minen muulla kuin tä ssä käyttöohjeessa
mainitulla tavalla saataa altistaa kä yt-täjän
turvallisuusluokan 1 ylittävä lle nä kymä ttöm ä lle
lasersä teilylle.
VARNING!
Om apparaten anvä nds på annat sä tt ä n vad som
specificeras i denna bruksanvising, kan anvä ndaren
utsä ttas fö r osynling laserstrå lning, som ö verskrider
grä nsen fö r laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’ utillisation de commandes, ré glages ou procé dures
autres que ceux spé cifié s peut entraî ner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserstå ling ved å bning, nå r sikkerhedsafbrydereer
ude af funktion. Undgå udsæ ttelse for strå ling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(SF-P101NR)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP Assy P.C.B
– 3 –
Page 4
ELECTRICAL MAIN PARTS LIST
PART NO. DESCRIPTION REF. NO. KANRI
NO.
IC
87-A20-955-010 IC,LA1828
87-A21-064-010 IC,LA4227
87-A21-520-040 C-IC,M61509FP
87-A20-446-010 C-IC,LA9241ML
87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D
8A-CD9-610-010 C-IC,LC865516A-5P16
87-A21-431-010 IC,BA4560N
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W)
87-026-447-080 TR,2SC1740S R
87-026-463-080 TR,2SA933S (0.3W)
87-026-213-080 CHIP-TR,DTC114YK
89-320-011-080 TR,2SC2001 (15W)
89-112-965-080 TR,2SA1296 (0.75W)
87-026-291-080 TR,DTC124XS
87-A30-226-010 TR,2SB1655E
87-026-462-080 TR,2SC1740 S(RS 0.3W)
89-318-154-080 TR,2SC1815 (0.4W)
89-109-332-380 TR,2SA933RS
89-113-187-080 TR,2SA1318TU
87-026-239-080 TR,DTC114TK (0.2W)
87-026-297-080 TR,DTA144TK
89-317-403-080 TR,2SC1740S
87-026-464-010 TR,DTC114TS
87-026-464-080 TR,DTC114TS (0.3W)
DIODE
87-020-465-080 DIODE,1SS133 (110MA)
87-027-607-080 ZENER,HZ7B3L
87-A40-466-080 ZENER,MTZJ2.7A
87-070-345-080 DIODE,IN4148
87-A40-648-080 ZENER,MTZJ8.2A
87-A40-234-080 ZENER,MTZJ5.6A
87-017-978-080 DIODE,1N4003
87-017-932-080 ZENER,MTZJ6.2B
87-A40-465-010 DIODE,FR202
MAIN C.B
C30 87-010-260-080 CAP, ELECT 47-25V
C211 87-010-805-080 CAP, S 1-16
C212 87-010-805-080 CAP, S 1-16
C215 87-016-460-080 C-CAP,S 0.22-16 B
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B
C232 87-010-213-080 C-CAP,S 0.015-50 B
C233 87-A10-201-080 C-CAP,S0.33-16 KB
C234 87-A10-201-080 C-CAP,S0.33-16 KB
C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B
C237 87-010-408-080 CAP, ELECT 47-50V
C239 87-010-197-080 CAP, CHIP 0.01 DM
C240 87-010-197-080 CAP, CHIP 0.01 DM
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V
C251 87-010-401-080 CAP, ELECT 1-50V
C263 87-010-178-080 CHIP CAP 1000P
C264 87-010-178-080 CHIP CAP 1000P
C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V
C267 87-010-112-080 CAP, ELECT 100-16V
C268 87-010-112-080 CAP, ELECT 100-16V
C271 87-010-235-080 CAP,E 470-16 SME
C272 87-010-235-080 CAP,E 470-16 SME
DESCRIPTION REF. NO. KANRI
PART NO.
NO.
C278 87-010-405-080 CAP, ELECT 10-50V
C279 87-010-385-080 CAP, ELECT 220-25V
C301 87-016-658-000 CAP,E 4700-35 M SMG
C306 87-010-404-080 CAP, ELECT 4.7-50V
C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V
C309 87-010-197-080 CAP, CHIP 0.01 DM
C310 87-010-248-080 CAP, ELECT 220-10V
C311 87-010-374-080 CAP, ELECT 47-10V
C312 87-010-385-080 CAP, ELECT 220-25V
C316 87-010-384-080 CAP, ELECT 100-25V
C321 87-010-197-080 CAP, CHIP 0.01 DM
C322 87-010-263-080 CAP, ELECT 100-10V
C325 87-010-405-080 CAP, ELECT 10-50V
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K
C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-50 B
C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-183-080 C-CAP,S 2700P-50 B
C423 87-010-956-080 CHIP-CAP,S 0.068-25B
C424 87-010-993-080 C-CAP,S 0.056-25 B
C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
C439 87-010-178-080 CHIP CAP 1000P
C440 87-010-145-080 C-CAP,S 1P-50 CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-312-080 C-CAP,S 15P-50 CH
C445 87-012-368-080 C-CAP,S 0.1-50 F
C446 87-012-368-080 C-CAP,S 0.1-50 F
C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-012-140-080 CAP 470P
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-010-190-080 S CHIP F 0.01
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-012-368-080 C-CAP,S 0.1-50 F
– 4 –
Page 5
PART NO. DESCRIPTION REF. NO. KANRI
NO.
C467 87-010-263-080 CAP, ELECT 100-10V
C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C489 87-012-368-080 C-CAP,S 0.1-50 F
C490 87-012-368-080 C-CAP,S 0.1-50 F
C491 87-010-197-080 CAP, CHIP 0.01 DM
C492 87-010-221-080 CAP, ELECT 470-10V
C494 87-010-190-080 S CHIP F 0.01
C501 87-012-368-080 C-CAP,S 0.1-50 F
C502 87-010-322-080 C-CAP,S 100P-50 CH
C503 87-010-322-080 C-CAP,S 100P-50 CH
C504 87-010-322-080 C-CAP,S 100P-50 CH
C505 87-010-322-080 C-CAP,S 100P-50 CH
C506 87-010-322-080 C-CAP,S 100P-50 CH
C510 87-016-669-080 C-CAP,S 0.1-25 K B
C801 87-010-248-080 CAP, ELECT 220-10V
C805 87-012-365-080 C-CAP,S 0.027-25VBK
C806 87-012-365-080 C-CAP,S 0.027-25VBK
C807 87-010-405-080 CAP, ELECT 10-50V
C808 87-010-405-080 CAP, ELECT 10-50V
C809 87-010-405-080 CAP, ELECT 10-50V
C810 87-010-405-080 CAP, ELECT 10-50V
C811 87-010-178-080 CHIP CAP 1000P
C812 87-010-178-080 CHIP CAP 1000P
C816 87-010-180-080 C-CER 1500P
C817 87-010-180-080 C-CER 1500P
C819 87-010-426-080 C-CAP,S 0.012-25 B
C820 87-010-426-080 C-CAP,S 0.012-25 B
C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V
C823 87-010-181-080 CAP,CHIP S 1800P
C824 87-010-181-080 CAP,CHIP S 1800P
C829 87-010-178-080 CHIP CAP 1000P
C830 87-010-178-080 CHIP CAP 1000P
C831 87-010-198-080 CAP, CHIP 0.022
C833 87-018-195-080 CAP, CER 1200P-16V
C834 87-010-248-080 CAP, ELECT 220-10V
C835 87-010-322-080 C-CAP,S 100P-50 CH
C836 87-010-322-080 C-CAP,S 100P-50 CH
C843 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-018-124-080 CAP, CER 270P-50V
C845 87-010-178-080 CHIP CAP 1000P
C846 87-010-263-080 CAP, ELECT 100-10V
C851 87-010-186-080 CAP,CHIP 4700P
C852 87-010-178-080 CHIP CAP 1000P
C853 87-018-211-080 CAP,TC U 0.01-50 Z F<K>
C853 87-A11-145-080 CAP,TC U 0.01-50 Z F<EXCEPT K>
CN201 87-099-018-010 CONN,16P
CN202 87-A60-685-010 CONN,4P H WHT EH
CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 87-099-416-010 CONN,3P EH H WHT
CN401 87-A60-424-010 CONN,16P V TOC-B
CN403 87-099-201-010 CONN,8P 6216 H
CN801 87-A60-110-010 CONN,4P V S2M-4W
CN802 87-049-469-010 CONN,4P V
CNA205 8A-CD9-626-010 CONN ASSY,2P DOOR
CNA302 8A-CDB-627-010 CONN ASSY,6P MA-TUNER
CNA402 8A-CDB-622-010 CONN ASSY,6P CD-MOTOR
DESCRIPTION REF. NO. KANRI
PART NO.
NO.
CNA801 8A-CDB-626-010 CONN ASSY,4P CASS HEAD
CNA802 8A-CDB-625-010 CONN ASSY,4P CASS MECHA
FC401 8A-CDB-623-010 FF-CABLE, 16P 1.0 CD-RF
L401 87-003-102-080 COIL, 10UH
L404 87-003-152-080 COIL, 100UH
L801 87-007-342-010 COIL,OSC 85K BIAS
R840 87-029-124-010 RES,FUSE 2.2-1/4
SFR430 87-024-437-080 SFR100K,RH063EC
SW801 88-CT6-619-010 BACK SLIDE SW 6P2T SHORTIN
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
TUNER C.B
C1 87-010-314-080 C-CAP,S 22P-50V
C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-314-080 C-CAP,S 22P-50V
C4 87-010-148-080 CAP, CHIP S 75P SL<EXCEPT K>
C5 87-010-378-080 CAP, ELECT 10-16V
C7 87-012-156-080 C-CAP,S 220P-50 CH
C8 87-010-197-080 CAP, CHIP 0.01 DM
C9 87-010-311-080 CAP 12P
C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-152-080 C-CAP,S 8P-50 CH
C12 87-010-314-080 C-CAP,S 22P-50V
C13 87-010-322-080 C-CAP,S 100P-50 CH
C14 87-010-148-080 CAP, CHIP S 75P SL
C15 87-016-669-080 C-CAP,S 0.1-25 K B
C16 87-010-178-080 CHIP CAP 1000P
C17 87-016-669-080 C-CAP,S 0.1-25 K B
C18 87-010-198-080 CAP, CHIP 0.022
C19 87-016-669-080 C-CAP,S 0.1-25 K B
C20 87-010-400-080 CAP, ELECT 0.47-50V
C21 87-010-403-080 CAP, ELECT 3.3-50V
C22 87-010-197-080 CAP, CHIP 0.01 DM
C24 87-010-188-080 CAP,CHIP 6800P
C25 87-010-188-080 CAP,CHIP 6800P
C26 87-016-669-080 C-CAP,S 0.1-25 K B
C27 87-016-669-080 C-CAP,S 0.1-25 K B
C28 87-010-992-080 C-CAP,S 0.047-25 B
C29 87-010-992-080 C-CAP,S 0.047-25 B
C30 87-010-248-080 CAP, ELECT 220-10V
C31 87-010-379-080 CAP, ELECT 22-16V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C33 87-010-197-080 CAP, CHIP 0.01 DM
C34 87-010-197-080 CAP, CHIP 0.01 DM
C35 87-010-197-080 CAP, CHIP 0.01 DM
C36 87-010-263-080 CAP, ELECT 100-10V
C37 87-010-197-080 CAP, CHIP 0.01 DM
C38 87-010-197-080 CAP, CHIP 0.01 DM
C41 87-010-318-080 C-CAP,S 47P-50 CH<K>
C44 87-010-302-080 C-CAP,S 270P-50 CH<K>
C51 87-010-197-080 CAP, CHIP 0.01 DM
C56 87-010-152-080 C-CAP,S 8P-50 CH<EXCEPT K>
CF1 87-A90-128-010 FLTR,AM IF CFAL-455
CF2 82-785-747-010 CF MS2 GHY R
CF3 82-785-747-010 CF MS2 GHY R
CN2 87-099-194-010 CONN,6P 6216V
D3 87-A40-128-080 C-VARI-CAP,HVU202A
L2 87-A50-560-010 COIL,FM BPF(ACD)
L3 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(COI)<EXCEPT K>
L3 8A-CD9-661-010 BAR-ANT,MW/LW 3B-ACD(COI)<K>
L4 87-A50-562-010 COIL,FM RF EX(ACD)
L5 87-A50-564-010 COIL,FM OSC EX(ACD)
L6 87-A50-337-010 COIL,AM OSC (TOKO)<EXCEPT K>
L7 87-A50-336-010 COIL,AM IFT (TOKO)
L8 87-A50-335-010 COIL,FM IFT (TOKO)
L9 87-A50-334-010 COIL,FM DET (TOKO)
L10 87-005-849-080 COIL,10UH(CECS)
L16 87-A50-569-010 COIL,LW OSC-ACD(COI)<K>
L17 87-A50-337-010 COIL,AM OSC (TOKO)<K>
– 5 –
Page 6
PART NO. DESCRIPTION REF. NO. KANRI
DESCRIPTION REF. NO. KANRI
NO.
S1 87-A91-549-010 SW,SL-6-4 SK64D01G06<K>
SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06<EXCEPT K>
TC5 87-011-221-080 TRIMMER,CER 30P 6.15X5.9 VC<K>
TC6 87-011-221-080 TRIMMER,CER 30P 6.15X5.9 VC<K>
VC1 87-A91-635-010 TUN-CAP,20P-140P E-ACD(MITSUMI
PART NO.
NO.
VOL C.B
CN607 84-722-632-010 CONN,2P H
S614 8Z-CT6-636-010 SW,TACT EVQJAC04M
S615 8Z-CT6-636-010 SW,TACT EVQJAC04M
FRONT C.B
C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-319-080 C-CAP,S 56P-50 CH
C604 87-010-317-010 CHIP CAP,S 39P CH
C605 87-010-263-080 CAP, ELECT 100-10V
C606 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C607 87-015-819-080 CAPACITOR,0.01
C608 87-010-405-080 CAP, ELECT 10-50V
C609 87-010-400-080 CAP, ELECT 0.47-50V
C611 87-010-248-080 CAP, ELECT 220-10V
C613 87-012-368-080 C-CAP,S 0.1-50 F
C614 87-010-312-080 C-CAP,S 15P-50 CH
CN601 87-099-033-010 16P 6216 H
CN602 87-099-201-010 CONN,8P 6216 H
CNA604 8A-CDB-616-010 CONN ASSY,6P KEY FUNCT
CNA606 8A-CDB-617-010 CONN ASSY,2P KEY VOL
FC601 8A-CDB-618-010 FF-CABLE, 16P 1.25 FR-MAIN
FC602 8A-CDB-619-010 FF-CABLE, 8P 1.25 CD-FR
L601 87-003-102-080 COIL, 10UH
LED602 88-CD6-630-010 LED,934ID RED
LED608 88-CD6-630-010 LED,934ID RED
LED611 87-CD8-616-010 LED,SA36-11 HWA-11.0
S601 8Z-CT6-636-010 SW,TACT EVQJAC04M
S602 8Z-CT6-636-010 SW,TACT EVQJAC04M
S603 8Z-CT6-636-010 SW,TACT EVQJAC04M
S604 8Z-CT6-636-010 SW,TACT EVQJAC04M
S605 8Z-CT6-636-010 SW,TACT EVQJAC04M
X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-030-376-080 VIB,CER CSA5.76MG200
PHONE C.B
CN204 87-049-469-010 CONN,4P V
CNA203 8A-CDB-624-010 CONN ASSY,3P H.P
CNA204 8A-CDB-633-010 CONN ASSY,4P SPKR
J251 87-009-216-010 JACK, DIA 3.5
BATT A C.B
C901 87-018-205-080 CAP, CERA-SOL 0.022
C902 87-018-205-080 CAP, CERA-SOL 0.022
C903 87-018-205-080 CAP, CERA-SOL 0.022
C904 87-018-205-080 CAP, CERA-SOL 0.022
CNA901 8A-CDB-621-010 CONN ASSY,3P POWER
!
PR901 87-A90-092-080 PROTECTOR,2.5A 491
!
PT901 8A-CDB-653-010 PT,E 2.5W EI48X23<K>
!
PT901 8A-CDB-651-010 PT,H 2.5W EI48X23<EXCEPT K>
BATT B C.B
CD MOTOR C.B
M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P
SW1 91-572-085-120 LEAF SW
KEY FUNCT C.B
CN605 87-099-417-010 CONN 6P EH H WHT
LED606 88-CD6-630-010 LED,934ID RED
LED607 88-CD6-630-010 LED,934ID RED
LED610 88-CD6-631-010 LED,934GD GRN
S606 8Z-CT6-636-010 SW,TACT EVQJAC04M
S607 8Z-CT6-636-010 SW,TACT EVQJAC04M
S608 8Z-CT6-636-010 SW,TACT EVQJAC04M
S609 8Z-CT6-636-010 SW,TACT EVQJAC04M
S611 8Z-CT6-636-010 SW,TACT EVQJAC04M
– 6 –
Page 7
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
B
E
Resistor Code
108
118
128
C
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
E C B
2SA1296
2SC1815
B C E
2SB1655E
E C B
2SC2001
2SA1318TU
E C B
2SC1740S/SR/SRS
2SA933S/RS
DTC124XS
DTC114TS
DTC114YK
DTC114TK
DTA144TK
2SC2714
– 7 –
Page 8
WIRING – 1 (MAIN)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 25 26 27 28 29 30 31 32
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 8 –
R
S
T
U
Page 9
WIRING – 2 (BATT A / BATT B)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 25 26 27 28 29 30 31 32
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 9 –
R
S
T
U
Page 10
WIRING – 3 (TUNER : LH, HA)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 25 26 27 28 29 30 31 32
A
B
C
D
E
F
G
H
VC001
TUNING
I
J
K
L
M
N
O
P
Q
– 12 –
R
S
T
U
Page 11
WIRING – 4 (TUNER : K)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 25 26 27 28 29 30 31 32
A
B
C
D
E
F
G
H
VC001
TUNING
I
J
K
L
M
N
O
P
Q
– 14 –
R
S
T
U
Page 12
WIRING – 5 (FRONT / KEY FUNCT / VOL / PHONE)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 25 26 27 28 29 30 31 32
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 16 –
R
S
T
U
Page 13
WIRING – 6 (CD MOTOR)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
A
I CD MOTOR C.B
M2
+
(SLED MOTOR)
_
(INSIDE LIMIT SW)
6
SW1
PIN3
1
TO/FROM A MAIN C.B (2/2) CNA402
M2
SW1
M1
M1
(SPINDLE MOTOR)
_
+
B
C
D
E
F
G
H
I
J
PICK UP ASSY
SF-P101NR
16
1
FC401
K
L
M
N
O
P
Q
R
S
T
TO/FROM A MAIN C.B (2/2) CN401
– 18 –
U
Page 14
IC BLOCK DIAGRAM
– 19 –
Page 15
IC DESCRIPTION
IC, LC78622ED
Pin No.
1 DEFI I Defect detection signal (DEF) input. ("L" is applied when not used.)
2 TAI I For PLL/Test input. A pull-down resistor is incorporated.
3 PDO O Phase comparison output to control the external VCO.
4 VVSS – Ground of the built-in VCO. Normally, 0V.
5 ISET I For the connection of a resistor which adjusts the PDO output current.
6 VVDD – Power supply of the built-in VCO.
7 FR I Adjusts the VCO frequency range.
8 VSS – Ground of digital circuits. Normally, 0V.
9 EFMO O For slice level control/EFM signal output.
10 EFMIN I EFM signal input.
11 T2 I Test input. A pull-down resistor is incorporated. Be sure to connect this to 0V.
12 CLV+
13 CLV-
14 V/P O
15 HFL I Track detection signal input. Schmitt trigger input.
16 TES I Track error signal input. Schmitt trigger input.
17 TOFF O Tracking off output.
Pin Name I/O
O Disc motor control tri-state outputs.
Output to monitor the automatic switching between the rough servo control and phase servo
control. "H" :Rough servo, "L": Phase servo.
Description
18 TGL O Tracking gain switching output. "L" raises the gain.
19 JP+
20 JP-
21 PCK O Monitors the clock signal for EFM data playback.4.3218MHz when the phase is locked.
22 FSEQ O
23 VDD – Power supply of digital circuits.
24 SL+ I/O General purpose input/output 1. Controlled by serial data command issued by the microprocessor.
25 SL– I/O General purpose input/output 2. Controlled by serial data command issued by the microprocessor.
26 NC – Not connected.
27 PUIN I/O CD pickup inside limit switch.
28 RW I/O Serial data command sled signal output terminal from microprocessor.
29 EMPH O Deemphasis monitor. "H": when playing a deemphasis disc. (Not used)
30 C2F O C2 flag output. (Not used)
31 DOUT O Outputs a digital OUT signal. (EIAJ format) (Not used)
32 T3
33 T4
34 N.C – Not connected.
O Track jump control tri-state outputs.
Sync signal detection output. Goes "H" when the sync signal detected from the EFM
signal matches the sync signal generated internally. (Not used)
I Test input. A pull-down resistor is incorporated. Be sure to connect this to 0V.
35 MUTEL O Lch 1-bit DAC/Lch muting output. (Not used)
– 20 –
Page 16
Pin No.
36 LVDD – Lch power supply.
37 LCHO O Lch output.
38 LVSS – Lch ground. Normally, 0V.
39 RVSS – Rch 1-bit DAC/Rch ground. Normally, 0V.
40 RCHO O Rch output.
41 RVDD – Rch power supply.
42 MUTER O Rch muting output. (Not used)
43 XVDD – Power supply of crystal oscillator.
44 XOUT O
45 XIN I
46 XVSS – Ground of crystal oscillator. Normally, 0V.
47 SBSY O Subcode block sync signal output. (Not used)
48 EFLG O C1,C2,single,duplex correction monitor. (Not used)
49 PW O Output of subcodes P,Q,R,S,T,U and W. (Not used)
50 SFSY O Subcode frame sync signal output. Falls when the subcode is set to the standby state.(No used)
51 SBCK I Subcode read-out clock input. Schmitt trigger input.("L" is applied when not used.)
52 FSX O 7.35 kHz sync signal output obtained by dividing the oscillator frequency. (Not used)
53 WRQ O Subcode Q standby output.
Pin Name
I/O Description
For the connection of a 16.9344 MHz crystal oscillator.
54 RWC I Read/write control input. Schmitt trigger input.
55 SQOUT O Subcode Q output.
56 COIN I Command input from the microprocessor.
57 CQCK I
58 RES I LC78622 reset input.
59 T11 O Test output. Set to open (normally, "L" output.) (Not used)
60 16M O 16.9344 MHz output. (Not used)
61 4.2M O 4.236 MHz output.
62 T5 I Test input. A pull-down resistor is incorporated. Be sure to connect to 0 V.
63 CS I Chip select input. A pull-down resistor is incorporated.
64 TEST1 I Test input with no pull-down resistor. Be sure to connect this to 0 V.
Command input retrieval clock or subcode retrieval clock input from SQOUT. Schmitt trigger
input.
– 21 –
Page 17
IC, LA9241ML
Pin No.
1 FIN2 O
2 FIN1 O For the connection of the pickup photodiode.
3E O
4 F O For the connection of the pickup photodiode.
5 TB I Inputs the DC components in the TE signal.
6 TE– O
7 TE O TE signal output.
8 TESI I TES (track error sense) comparator input.The TE signal is passed through a BPF.
9 SCI I Shock detection input.
10 TH I Sets the time constant for the tracking gain.
11 TA O TA amp output.
12 TD– I Composes the tracking phase compensation constant between the TD and VR pins.
13 TD O Sets the tracking phase compensation.
14 JP I Sets the amplitude of the tracking jump signal (kick pulses).
Pin Name I/O
For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF
signal and subtraction from it create an EF signal.
For the connection of the pickup photodiode. Subtraction from the F pin creates a TE
signal.
For the connection of a resistor which sets the gain of the TE signal between this pin
and the TE pin.
Description
15 TO O Tracking control signal output.
16 FD O Focusing control signal output.
17 FD– I Composes the focusing phase compensation constant between the FD and FA pins.
18 FA O Composes the focusing phase compensation constant between the FD- and FA- pins.
19 FA– I Composes the focusing phase compensation constant between the FA and FE pins.
20 FE O FE signal output.
21 FE– I
22 AGND O Ground of analog signals.
23 SP O Single-ended output of the signals input to the CV+ and CV- pins.
24 SPI I Spindle amp input.
25 SPG I For the connection of a resistor which sets the gain in the spindle 12cm mode.
26 SP– I For the connection of the spindle phase compensation constant with the SPD pin.
27 SPD O Spindle control signal output.
28 SLEQ I For the connection of sled phase compensation constant.
29 SLD O Sled control signal output.
30 SL–
31 SL+
For the connection of a resistor whichs sets the gain of the FE signal between this pin
and the TE pin.
I Sled feed signal input from the microprocessor.
32 JP–
33 JP+
34 TGL I Tracking gain control signal input from the DSP. Low gain when TGL is "H".
35 TOFF I Tracking off control signal input from the DSP. Off when TOFF is "H".
36 TES O Outputs the TES signal to the DSP.
I Tracking signal input from the DSP.
– 22 –
Page 18
Pin No.
37 HFL O
38 SLOF I Sled servo off control input.
I/O Description Pin Name
The HFL (high frequency level) signal is used to judge whether the main beam is positioned on
the pit or on the mirror.
39 CV–
40 CV+
41 RFSM O RF output.
42 RFS– O Sets the RF gain and the EFM signal's 3T compensation constant together with the RFSM pin.
43 SLC O
44 SL1 I Input to control the DSP's data slice level.
45 DGND – Ground of digital signals.
46 FSC O Output for the focus search smoothing capacitor.
47 TBC I The TBC (tracking balance control) signal sets the EF balance variation range.
48 NC – Not connected.
49 DEF O Disc defect detection output.
50 CLK I Reference clock input. 4.23 MHz is input from the DSP.
51 CL I Microprocessor command clock input.
52 DAT I Microprocessor command data input.
53 CE I Microprocessor chip enable input.
54 DRF O DRF (detect RF) is an output to detect the RF level.
55 FSS I
I CLV error signal input from the DSP.
The SLC (slice level control) signal is output to control the DSP's data slice level of the RF
waveform.
The FSS (focus search select) signal switches the focus search modes (+/-search / +search with
respect to the reference voltage).
56 VCC2 – VCC of servo and digital circuits.
57 REF1 _ For the connection of bypass capacitor for the reference voltage.
58 VR O Reference voltage output.
59 LF2 – Sets the time constant for disc defect detection.
60 PH1 – For the connection of a capacitor to hold the RF signal peak.
61 BH1 – For the connection of a capacitor to hold the RF signal bottom.
62 LDD O APC circuit output.
63 LDS I APC circuit input.
64 VCC1 – VCC of RF signal circuits.
– 23 –
Page 19
IC, LC865516A-5P16
Pin No. Pin Name I/O Description
1
SEG E
O
SEG E control.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
SEG F
SEG G
NC
I-RST
XT1 (IN)
NC
XT2 (OUT)
VSS
CF1 (IN)
CF2 (OUT)
VDD
I-KEY0
I-KEY1
I-MOTOR
I-CD SW
O-SHIFT
NC
O
SEG F control.
O
SEG G control.
—
Not connected.
I
Microprocessor reset input.
I
Connected to an external 32.768 kHz crystal oscillator.
—
Not connected.
O
Connected to an external 32.768 kHz crystal oscillator.
—
GND.
I
Connected to an external 5.76 MHz ceramic filter.
O
Connected to an external 5.76 MHz ceramic filter.
—
Microprocessor power supply (+5 V).
I
Key AD input. (AD)
I
Key AD input. (AD)
I
Deck status input. (AD)
I
CD door switch status input.
O
Main clock shift output.
—
Not connected.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
O-BASS LED
O-QS LED
O-SFT LED
I-DRF
I-WRQ
NC
I-REM
O-CD ON
O-TU ON
O-P.CONT
NC
O-BEAT
O-MUTE
O-DIGIT
O-SEG REPEAT
O-COIN
I-SQOUT
O
BASS LED ON/OFF control output. (Not used)
O
Q sound LED ON/OFF control output.
—
Not used.
I
CD RF level detection input.
I
CD subcode Q standby input.
—
Not connected.
I
Remote control input.
O
CD power control output.
O
TU power control output.
O
The main power supply control output.
—
Not connected.
O
Beat sw control output.
O
Main mute output.
O
7-segment LED power supply control output.
O
REPEAT LED ON/OFF control output.
O
CD command output.
I
CD subcode Q input.
36
37
38
39
40
41
O-CQCK
O-RWC
O-DATA
O-CD LED
O-TU LED
O-TA LED
O
CD command/CLK for subcode.
O
CD read/write control output.
O
Data output to M61509FP.
O
LED ON/OFF control output for the CD function.
O
LED ON/OFF control output for the TU function.
O
LED ON/OFF control output for the TA function. (Not used)
– 24 –
Page 20
Pin No. Pin Name I/O Description
42
43
44
45
46
47
48
NC
SEG DP
SEG A
SEG B
SEG C
SEG D
NC
—
O
O
O
O
O
—
Not connected.
SEG DP control.
SEG A control.
SEG B control.
SEG C control.
SEG D control.
Not connected.
– 25 –
Page 21
ADJUSTMENT <TUNER / DECK / CD>
B TUNER C.B <LH, HA>
4
L006
VC001
1
TC003
TC004
2
5
TC001
TC002
L005
L004
L009
TP6 (RCH)
TP5 (LCH)
IC001
L007
L008
6
1
~
6
3
6
L003
2
B TUNER C.B <K>
TP6 (RCH)
8
1
~
TP5 (LCH)
1
L017
3
TC006
2
6
3
4
L016
TC003
TC004
TC001
VC001
TC005
TC002
L005
L009
8
IC001
L007
5
L008
8
L004
L003
7
LW (1/2)
MW (2/2)
4
2
– 26 –
Page 22
< RADIO SECTION > <LH, HA>
1. AM Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L006, TC003
• Method:
L006 ....................................................................... 517kHz
TC003 ................................................................... 1750kHz
< RADIO SECTION > <K>
1. LW Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L016, TC005
• Method:
L016 ....................................................................... 145kHz
TC005 ..................................................................... 295kHz
2. AM Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003, TC004
• Method:
L003 ....................................................................... 600kHz
TC004 ................................................................... 1400kHz
3. AM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L007
• Method:
L007 ....................................................................... 455kHz
4. FM Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L005, TC001
• Method:
L005 ........................................................................ 87MHz
TC001 .................................................................... 109MHz
5. FM Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L004, TC002
• Method:
L004 ........................................................................ 88MHz
TC002 .................................................................... 108MHz
2. LW Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003 (1/2), TC006
• Method:
L003 (1/2)............................................................... 150kHz
TC006 ..................................................................... 285kHz
3. MW Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L017, TC003
• Method:
L017 ....................................................................... 515kHz
TC003 ................................................................... 1635kHz
4. MW Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003 (2/2), TC004
• Method:
L003 (2/2)............................................................... 600kHz
TC004 ................................................................... 1400kHz
5. AM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L007
• Method:
L007 ....................................................................... 455kHz
6. FM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L008, L009
• Method:
L008, L009 ...........................................................10.7MHz
6. FM Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L005, TC001
• Method:
L005 ..................................................................... 87.4MHz
TC001 ................................................................. 108.3MHz
7. FM Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L004, TC002
• Method:
L004 ........................................................................ 88MHz
TC002 .................................................................... 108MHz
8. FM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L008, L009
• Method:
L008, L009 ...........................................................10.7MHz
– 27 –
Page 23
A MAIN C.B
1
1
TP4
IC404
TP3
IC401
SFR430
L801
3
TP2
2
– 28 –
Page 24
< CD SECTION >
1. Focus Bias Adjustment
Make the focus bias adjustment when replacing and repairing
the optical block.
Oscilloscope
(DC range)
TP3 (RF)
TP4 (VREF)
1) Connect an oscilloscope to the test point TP3 (RF) and TP4
(VREF).
2) Turn on the power switch.
3) Insert test disc TCD-782 (YEDS-18) and play back the second
composition.
4) Adjust SFR430 so that RF signal of the test point TP3 (RF) is
MAX and CLEAREST.
+
-
< TAPE RECORDER SECTION >
2. Bias Adjustment
• Test tape: TTA-630
• Test Point: TP2
• Adjustment location: L801
• Method:
L801 .............................................................. 85kHz± 2kHz
3. Azimuth Adjustment
Condition: • Test tape: TTA-320
• Test point: PHONE JACK
• Adjustment location:Azimuth adjustment
screw
Method: Play back the test tape and adjust the screw so that the
output is maximum.
EYE PATTERN
must be CLEAR and MAX
MAX
0V
VOLT / DIV: 200mV
TIME / DIV: 0.5µ s
– 29 –
Page 25
MECHANICAL EXPLODED VIEW 1 / 1
14
13
17
16
15
5
20
P.C.B
19
18
H
39
37
H
55
40
56
F
35
41
36
F
H
38
E
50
F
66
49
51
P.C.B
42
48
43
B
D
B
D
E
46
44
45
P.C.B
C
28
C
23
22
21
25
C
H
C
6
6
C
24
DA11T3C
65
27
26
P.C.B
63
24
D
A
A
26
A
57
H
62
60
26
A
D
29
C
52
30
32
7
34
33
P.C.B
D
H
D
P.C.B
58
31
I
CHASS,TU
54
P.C.B
64
11
2
1
3
12
10
4
9
8
7
59
53
P.C.B
H
6
5
C
D
C
C
6
D
G
D
61
D
TN-21ZVC-2000
CSD-A310 KSC,LHSC,LHDC,LHG
(FileName:EXP .EPS)
2000/4/12 ACD-1 1
47
– 30 –
Page 26
MECHANICAL PARTS LIST 1 / 1
PART NO. DESCRIPTION REF. NO. KANRI
NO.
1 8A-CDB-006-010 WINDOW,CASS<KSC,LHSC,HASCC>
1 8A-CDB-043-010 WINDOW,CASS [G]<LHGC>
1 8A-CDB-052-010 WINDOW,CASS [D]<LHDC>
2 8A-CDB-008-010 BOX,CASS<KSC,LHSC,HASCC>
2 8A-CDB-045-010 BOX,CASS [G]<LHGC>
2 8A-CDB-054-010 BOX,CASS [D]<LHDC>
3 8A-CDB-204-010 SPR-T,CASS
4 8A-CDB-001-010 CABI,FR
5 88-CD8-622-010 SPKR,F 77 7OHM 3W
6 8Z-CDB-208-010 HLDR,SPKR
7 8A-CDB-205-010 PLATE,OIL DUMP
8 87-063-164-010 OIL-DMPR 80
9 8A-CDB-206-010 BASE,CD
10 8A-CDB-016-010 BTN,CD
11 8A-CDB-004-010 WINDOW,DISP<KSC,LHSC,HASCC>
11 8A-CDB-041-010 WINDOW,DISP [G]<LHGC>
11 8A-CDB-050-010 WINDOW,DISP [D]<LHDC>
12 8A-CDB-023-010 GRILLE,SPKR<KSC,LHSC,HASCC>
12 8A-CDB-049-010 GRILLE,SPEAKER [G]<LHGC>
12 8A-CDB-058-010 GRILLE,SPKR [D]<LHDC>
13 8Z-CT6-213-010 BASE,CHUCK
14 8Z-CT6-214-010 RING,CHUCK
15 87-036-368-010 MAGNET
16 86-CT9-222-010 PLATE,MAGNET
17 86-CT9-217-010 HLDR,CHUCK A(S)
18 8A-CDB-009-010 BOX,CD<KSC,LHSC,HASCC>
18 8A-CDB-046-010 BOX,CD [G]<LHGC>
18 8A-CDB-055-010 BOX,CD [D]<LHDC>
19 8A-CDB-005-010 WINDOW,CD<KSC,LHSC,HASCC>
19 8A-CDB-042-010 WINDOW,CD [G]<LHGC>
19 8A-CDB-051-010 WINDOW,CD [D]<LHDC>
20 8A-CDB-213-010 BASE,FUNC
21 8A-CDB-013-010 BTN,FUNC<KSC,LHSC,HASCC>
21 8A-CDB-048-010 BTN,FUNC [G]<LHGC>
21 8A-CDB-057-010 BTN,FUNC [D]<LHDC>
22 8A-CDB-014-010 BTN,QSOUND
23 8A-CDB-003-010 CHAS,CD
24 8A-CDB-021-010 LENS,FUNC
25 8A-CDB-203-010 HLDR,LED FUNC
26 88-CH6-220-010 CUSHION,CD A
27 8Z-CT9-064-010 PANEL CD
28 87-036-389-010 SW,PUSH LOCK
29 8A-CDB-218-010 SPR-T,CD
30 8A-CD9-661-010 BAR-ANT,MW/LW 3B-ACD(COI)<KSC>
30 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(COI)<EXCEPT KSC>
31 8A-CDB-210-010 DRUM,GEAR
32 87-063-165-010 OIL-DMPR 150
33 8A-CDB-214-010 BASE,VOL
34 8A-CDB-012-010 BTN,VOL<KSC,LHSC,HASCC>
34 8A-CDB-047-010 BTN,VOL [G]<LHGC>
DESCRIPTION REF. NO. KANRI
34 8A-CDB-056-010 BTN,VOL [D]<LHDC>
35 8A-CDB-022-010 POINTER,TU
36 8A-CDB-209-010 HLDR,BTN TUN
37 8A-CDB-211-010 GEAR,MID TUN
38 8A-CDB-011-010 BTN,TUN
39 8A-CDB-219-010 HLDR,TRAN
40 8A-CDB-653-010 PT,E 2.5W EI48X23<KSC>
40 8A-CDB-651-010 PT,H 2.5W EI48X23<EXCEPT KSC>
41 8A-CDB-019-010 HANDL,GRIP
42 8A-CDB-018-010 COVER, HANDL
43 8Z-CH4-640-010 ANT,ROD
44 8A-CDB-002-010 CABI,REAR
45 8A-CDB-027-010 WINDOW,TU EZ<KSC>
45 8A-CDB-007-010 WINDOW,TU<LHSC,HASCC>
45 8A-CDB-044-010 WINDOW,TU [G]<LHGC>
45 8A-CDB-053-010 WINDOW,TU [D]<LHDC>
46 8A-CDB-217-010 LEVER,BAND
47 8A-CDB-020-010 LID,BATT
48 86-CT9-223-010 CUSH,FOOT
49 8A-CDB-207-010 HLDR,ANT
50 87-A60-178-010 JACK,AC E W/SW
51 8A-CDB-215-010 SPR-T,BATT
52 8A-CDB-220-010 HLDR,M66 BAR ANT
53 8A-CDB-015-010 KEY,CASS
54 8A-CDB-216-010 PLATE,TRAN
55 8A-CDB-010-010 BTN,TU
56 87-A90-086-010 COVER,AC JACK
57 8A-CDB-618-010 FF-CABLE, 16P 1.25 FR-MAIN
58 8A-CDB-623-010 FF-CABLE, 16P 1.0 CD-RF
59 8A-CDB-619-010 FF-CABLE, 8P 1.25 CD-FR
60 8A-CDB-208-010 HLDR,LED SA/SC36
61 8A-CDB-212-010 PLATE,REC
62 8A-CDB-206-010 BASE,CD
63 8A-CDB-016-010 BTN,CD
64 8A-CDB-016-010 BTN,CD
65 8A-CDB-203-010 HLDR,LED FUNC
66 87-A91-369-010 SW,AC SL222 SD KGA41700<EXCEPT KSC>
A 81-CD5-204-010 SCREW CD
B 87-651-104-410 VT1+3-30
C 87-741-096-410 UT2+3-10
D 87-751-097-410 SCREW 3X12
E 87-261-096-410 SCREW,V+3-10 GLD
F 87-741-074-410 UT2+2.6-8
G 87-261-032-410 V+2-3 GLD
H 87-751-095-410 VT2+3-8 W/O
I 87-745-094-410 UT2+3-6
PART NO.
!
!
!
!
NO.
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange
– 31 –
Page 27
TAPE MECHANISM EXPLODED VIEW 1 / 1
F
G
1
46
47
E
2
LUG PLATE
52
4
3
5
36
25
21
20
22
23
24
c
51
26
27
28
A
6
8
11
a
10
18
J
L
b
19
14
12
15
16
17
34
35
7
37
13
31
49
c
C
48
30
b
a
C
32
33
A
9
29
38
39
42
– 32 –
43
D
D
K
41
40
I
50
45
CSD-FD71
TN-21ZVC-2000
B
H
B
44
Page 28
TAPE MECHANISM PARTS LIST 1 / 1
PART NO. DESCRIPTION REF. NO. KANRI
NO.
1 S1-921-030-4A0 HEAD BASE
2 S1-821-030-070 AZIMUTH SPRING
3 S1-921-030-090 PANEL P SPRING
4 S1-921-260-050 GEAR PLATE SPRING
5 S1-921-265-020 GEAR PLATE ASSY
6 S1-510-020-020 REC SPRING PLATE
7 S1-921-015-010 CHASSIS ASSY
8 S1-921-030-110 HEAD PANEL
9 S1-921-143-160 BASE ASSY
10 S1-921-141-8A0 M CONTROL SPRING
11 S1-921-260-4A0 SENSING LEVER
12 S1-921-043-100 PINCH ROLLER ARM ASSY
13 S1-921-130-010 EJECT SLIDE LEVER
14 S1-921-141-3A0 P CONTROL SPRING
15 S1-921-140-550 PAUSE LEVER(E)
16 S1-921-140-120 PAUSE LEVER SPRING
17 S1-921-140-110 PAUSE STOPPER
18 S1-921-140-150 BUTTON LEVER SPRING(B)
19 S1-821-011-590 E KICK LEVER
20 S1-921-141-070 BUTTON LEVER SPRING(A)
21 S6-401-011-490 LEAF SW MSW-1541T
22 S1-921-140-090 SWITCH ACTUATOR
23 S1-921-140-080 PUSH BUTTON ACTUATOR
24 S1-921-140-190 PLAY BUTTON LEVER
25 S1-921-030-100 MG ARM SPRING
26 S1-921-140-040 REW BUTTON LEVER
27 S1-921-140-050 FF,BUTTON REVER
28 S1-921-140-060 STOP BUTTON LEVER
29 S1-921-140-600 PAUSE BUTTON LEVER
30 S1-821-100-700 FF GEAR
31 S1-921-050-060 SENSER
32 S1-921-053-100 TAKE UP REEL ASSY
33 S1-829-100-010 PACK SPRING
34 S1-921-050-150 S REEL HUB
35 S1-921-050-220 BACK TENSION SPRING
DESCRIPTION REF. NO. KANRI
PART NO.
NO.
36 S1-921-140-030 REC BUTTON LEVER
37 S1-921-140-170 P.S.LEVER SPRING
38 S1-921-073-040 RF CLUTCH ASSY
39 S1-921-070-030 RF BELT
40 S1-921-260-020 CAM GEAR
41 S1-921-140-160 E ACTUATOR SPRING
42 S1-921-093-210 FLYWHEEL ASSY
43 S1-921-090-380 MAIN BELT
44 S1-921-120-590 MOTOR PULLEY
45 S6-002-030-220 MOTOR EG530AD-2B
46 S6-209-100-100 E HEAD PH-K380-MS1
47 S1-921-030-050 MG ARM
48 S1-921-140-210 REC BUTTON LEVER SPRING
49 S1-821-100-690 RECORD SAFETY LEVER
50 S1-821-128-9A0 MOTOR BRACKET
51 S1-821-010-500 PLAY BUTTON LEVER SPRING
52 S6-201-011-110 HEAD,RP7442ES-0951
A S9-P04-200-310 C TAPPING SCREW 2-3
B S1-921-120-020 MOTOR COLLER SCREW
C S9-B10-200-510 P TAPPING BIND SCREW M2-5
D S9-C07-204-510 SCREW,TAPPING(CAMERA)M2-4.5
E S9-P01-200-610 SCREW,M2-6
F S9-B01-200-310 (+)BIND SCREW M2-3
G S9-F08-200-710 AZIMUTH SCREW M2-7
H S1-921-120-030 MB SCREW
I S9-W02-300-100 P WASHER CUT 1.2-3.8-0.3
J S9-W02-500-100 P WASHER CUT 1.45-3.8-0.5
K S9-W01-400-100 P WASHER 2-3.5-0.4
L S9-W01-130-200 P WASHER 2.1-4-0.13
– 33 –
Page 29
CD MECHANISM EXPLODED VIEW 1 / 1
SHAFT,SLIDE
B
SF-P101NR
CHASSIS
B
1
2
A
A
3
SPINDLE
MOTOR(M1)
SLED MOTOR (M2)
CD MOTOR C.B
– 34 –
Page 30
CD MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 S2-121-A28-400 COVER GEAR
2 S2-511-A21-000 GEAR MIDDLE
3 S2-511-A21-100 GEAR,DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
DESCRIPTION REF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
1 8A-CDB-905-010 IB,K(E)FM<K >
1 8A-CDB-902-010 IB,LH(ESP)FM<EXCEPT K >
!
2 87-A80-119-010 AC CORD SET ASSY,AZ<HA>
2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL<EXCEPT HA>
!
3 87-099-726-010 PLUG,ADPTR CONV(K)<K >
!
4 87-A91-017-010 PLUG,CONVERSION JT-0476<EXCEPT K >
NO.
DESCRIPTION REF. NO. KANRI
– 35 –
Page 31
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore 9420208 0251431