How it Works
Aiwa
Loading...
CSD-A280
Service Manual
15 pgs964.86 Kb0

Aiwa CSDA-280 Service manual

Download
Page 1
CSD-A280
LH
SERVICE MANUAL
COMPACT DISC
STEREO CASSETTE RECODER
This Service Manual is the "Revision Publishing" and replaces "Simple Manual" (S/M Code No. 09-002-430-0T1).
BASIC CD MECHANISM : DA11T3 BASIC TAPE MECHANISM : TN-21ZVC-2000
S/M Code No. 09-002-430-0R1
DATA
Page 2
SPECIFICATIONS
Design and specifications are subject to change without
•
notice
.
ACCESSORIES/PACKAGE LIST
REF. NO PART NO. KANRI DESCRIPTION
1 8A-CD9-902-010 IB,LH(ESP)B
!
2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL 3 8Z-CDK-962-010 RC UNIT,RC-ZAT02(VS) 4 8Z-CD5-634-010 COVER,AC SOCKET
!
5 87-A90-312-010 PLUG,CONVERSION WTN-1157R1
NO.
2
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
Caution: Invisible laser radiation when open and interlocks defeated avoid expo­sure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit­ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit­tävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block (SF-P101NR)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
1) After the connection, remove solder shown in the right figure.
Solder
3
Page 4
ELECTRICAL MAIN PARTS LIST
T
REF. NO PART NO. KANRI DESCRIPTION
IC 87-A20-955-010 IC,LA1828
87-A21-090-010 IC,LA4600 87-A21-520-040 C-IC,M61509FP 87-A20-446-010 C-IC,LA9241ML 87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D 8A-CD9-610-010 C-IC,LC865516A-5916 87-A20-650-010 IC,RPM6938-V11 87-A21-431-010 IC,BA4560N
TRANSISTOR 89-327-143-080 TR,2SC2714 (0.1W)
89-327-125-080 CHIP TR,2SC2712GR 87-026-230-080 CHIP-TR,DTA114YK 87-026-213-080 CHIP-TR,DTC114YK 89-318-154-080 TR,2SC1815Y
89-112-965-080 TR,2SA1296 (0.75W) 87-026-463-080 TR,2SA933S (0.3W) 87-026-291-080 TR,DTC124XS 89-213-702-080 TR,2SB1370E 87-026-462-080 TR,2SC1740 S(RS 0.3W)
89-109-332-380 TR,2SA933RS 89-113-187-080 TR,2SA1318TU 87-026-295-080 TR,DTC144TK 87-026-237-080 CHIP-TR,DTC124XK 89-317-403-080 TR,2SC1740S
87-026-464-010 TR,DTC114TS 87-026-464-080 TR,DTC114TS (0.3W)
DIODE 87-020-465-080 DIODE,1SS133 (110MA)
87-027-607-080 ZENER,HZ7B3L 87-070-345-080 DIODE,1N4148 87-A40-648-080 ZENER,MTZJ8.2A 87-A40-234-080 ZENER,MTZJ5.6A
87-017-978-080 DIODE,1N4003 87-027-702-080 DIODE,ZENER HZ6C2L (200MA) 87-A40-465-010 DIODE,FR202
MAIN C.B C211 87-010-805-080 C-CAP,S 0.15-50 M F
C212 87-010-805-080 C-CAP,S 0.15-50 M F C215 87-016-460-080 C-CAP,S 0.22-16 B C216 87-016-460-080 C-CAP,S 0.22-16 B C231 87-010-213-080 C-CAP,S 0.015-50 B
C232 87-010-213-080 C-CAP,S 0.015-50 B C233 87-A10-201-080 C-CAP,S0.33-16 KB C234 87-A10-201-080 C-CAP,S0.33-16 KB C235 87-016-669-080 C-CAP,S 0.1-25 K B C236 87-016-669-080 C-CAP,S 0.1-25 K B
C237 87-010-408-080 CAP,E 470-6.3 M SME C239 87-010-197-080 CAP, CHIP 0.01 DM C240 87-010-197-080 CAP, CHIP 0.01 DM C247 87-010-401-080 CAP.E 1-50 M 11L SME C248 87-010-401-080 CAP,E 1-50 M 11L SME
C310 87-010-248-080 CAP, ELECT 220-10V C316 87-010-263-080 CAP,E 100-10 M 11L SME C317 87-015-819-080 C-CAP,0.01-50 K B C3216 C801 87-010-248-080 CAP, ELECT 220-10V C805 87-012-365-080 C-CAP,S 0.027-25VBK
C806 87-012-365-080 C-CAP,S 0.027-25VBK C807 87-010-405-080 CAP, ELECT 10-50V C808 87-010-405-080 CAP, ELECT 10-50V C809 87-010-405-080 CAP, ELECT 1-50V C810 87-010-405-080 CAP, ELECT 1-50V
NO.
REF. NO PART NO. KANRI DESCRIPTION
C811 87-010-178-080 CHIP CAP 1000P C812 87-010-178-080 CHIP CAP 1000P C816 87-010-180-080 C-CER 1500P C817 87-010-180-080 C-CER 1500P C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V C823 87-010-178-080 CHIP CAP 1000P C824 87-010-178-080 CHIP CAP 1000P C829 87-010-178-080 CHIP CAP 1000P C830 87-010-178-080 CHIP CAP 1000P
C833 87-018-195-080 CAP, CER 1200P-16V C834 87-010-248-080 CAP, ELECT 220-10V C835 87-010-322-080 C-CAP,S 100P-50 CH C836 87-010-322-080 C-CAP,S 100P-50 CH C843 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-018-124-080 CAP, CER 270P-50V C845 87-010-178-080 CHIP CAP 1000P C846 87-010-263-080 CAP, ELECT 100-10V C851 87-010-186-080 CAP,CHIP 4700P C852 87-010-178-080 CHIP CAP 1000P
C853 87-A11-145-080 CAP,TC U 0.01-50 Z F CN201 87-099-018-010 CONN,16P CN801 87-A60-110-010 CONN,4P V S2M-4W CNA302 8A-CD9-629-010 CONN ASSY,6P MA-TU L801 87-007-342-010 COIL,OSC 85K BIAS
SP904 87-CD6-213-010 SPR-C,BATT (-) SW801 8Z-CD9-609-010 SW,SL 1-6-2 PS62D01
CD C.B C30 87-010-260-080 CAP, ELECT 47-25V
C251 87-010-404-080 CAP.E 4.7-50 M 11L SME C263 87-010-178-080 CHIP CAP 1000P C264 87-010-178-080 CHIP CAP 1000P C266 87-010-545-080 CAP, ELECT 0.22-50V
C267 87-010-545-080 CAP, ELECT 0.22-50V C271 87-010-237-080 CAP, ELECT 1000-16V C272 87-010-237-080 CAP, ELECT 1000-16V C277 87-010-404-080 CAP, ELECT 4.7-50V C278 87-010-263-080 CAP, ELECT 100-10V
C279 87-010-263-080 CAP, ELECT 100-10V C301 87-016-495-000 CAP,E 3300-25 M SMG C302 87-010-265-080 CAP,E 33-16 M 11L SME C306 87-010-404-080 CAP, ELECT 4.7-50V C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V C311 87-010-374-080 CAP, ELECT 47-10V C312 87-010-385-080 CAP, ELECT 220-25V C321 87-010-197-080 CAP, CHIP 0.01 DM C322 87-010-263-080 CAP, ELECT 100-10V
C325 87-010-405-080 CAP, ELECT 10-50V C401 87-010-403-080 CAP, ELECT 3.3-50V C402 87-010-197-080 CAP, CHIP 0.01 DM C403 87-010-263-080 CAP, ELECT 100-10V C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM C406 87-010-374-080 CAP, ELECT 47-10V C407 87-010-178-080 CHIP CAP 1000P C408 87-010-198-080 CAP, CHIP 0.022 C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V C411 87-A11-177-080 C-CAP,S 0.15-16 K B C412 87-010-401-080 CAP, ELECT 1-50V C413 87-016-369-080 C-CAP,S 0.033-25 B K C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V C417 87-012-157-080 C-CAP,S 330P-50 CH C418 87-010-213-080 C-CAP,S 0.015-50 B C419 87-A11-608-080 C-CAP,S 0.33-25 K B C420 87-016-369-080 C-CAP,S 0.033-25 B K
NO.
4
Page 5
REF. NO PART NO. KANRI DESCRIPTION
C421 87-A11-177-080 C-CAP,S 0.15-16 K B C422 87-010-184-080 CHIP CAPACITOR 3300P(K) C423 87-010-992-080 C-CAP,S 0.047-25 B C424 87-016-460-080 C-CAP,S 0.22-16 B C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B C428 87-010-197-080 CAP, CHIP 0.01 DM C429 87-010-186-080 CAP,CHIP 4700P C430 87-012-156-080 C-CAP,S 220P-50 CH C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V C433 87-010-401-080 CAP, ELECT 1-50V C434 87-010-184-080 CHIP CAPACITOR 3300P(K) C435 87-010-197-080 CAP, CHIP 0.01 DM C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V C438 87-016-669-080 C-CAP,S 0.1-25 K B C439 87-010-178-080 CHIP CAP 1000P C440 87-010-145-080 C-CAP,S 1P-50 C CH GRM C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-313-080 CAP, CHIP 18P C445 87-012-368-080 C-CAP,S 0.1-50 F C446 87-012-368-080 C-CAP,S 0.1-50 F C447 87-012-368-080 C-CAP,S 0.1-50 F C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-012-140-080 CAP 470P C451 87-012-156-080 C-CAP,S 220P-50 CH C455 87-010-247-080 CAP, ELECT 100-50V C457 87-010-312-080 C-CAP,S 15P-50 CH C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V C460 87-015-819-080 CAPACITOR,0.01 C461 87-010-197-080 CAP, CHIP 0.01 DM C462 87-010-248-080 CAP, ELECT 220-10V C463 87-010-197-080 CAP, CHIP 0.01 DM
C465 87-010-404-080 CAP, ELECT 4.7-50V C466 87-012-368-080 C-CAP,S 0.1-50 F C467 87-010-263-080 CAP, ELECT 100-10V C469 87-012-154-080 C-CAP,S 150P-50 CH C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME C477 87-010-197-080 CAP, CHIP 0.01 DM C478 87-010-263-080 CAP, ELECT 100-10V C479 87-010-197-080 CAP, CHIP 0.01 DM C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V C482 87-010-405-080 CAP, ELECT 10-50V C489 87-012-368-080 C-CAP,S 0.1-50 F C490 87-012-368-080 C-CAP,S 0.1-50 F C491 87-010-197-080 CAP, CHIP 0.01 DM
C492 87-010-221-080 CAP, ELECT 470-10V C493 87-010-180-080 C-CAP,S 1500P-50 K B C2012 C494 87-010-197-080 CAP, CHIP 0.01 DM C501 87-012-368-080 C-CAP,S 0.1-50 F C502 87-010-322-080 C-CAP,S 100P-50 CH
C503 87-010-322-080 C-CAP,S 100P-50 CH C504 87-010-322-080 C-CAP,S 100P-50 CH C505 87-010-322-080 C-CAP,S 100P-50 CH C506 87-010-322-080 C-CAP,S 100P-50 CH C510 87-016-669-080 C-CAP,S 0.1-25 K B
C831 87-010-198-080 CAP, CHIP 0.022 CN202 8A-CH4-689-010 CONN,3P V 2.5 CN205 87-A60-109-010 CONN,2P V S2M-2W CN301 8A-CH4-689-010 CONN,3P V 2.5 CN401 87-A60-424-010 CONN,16P V TOC-B
NO.
REF. NO PART NO. KANRI DESCRIPTION
CN403 87-099-201-010 CONN,8P 6216 H CN802 8A-CH4-687-010 CONN,4P V 2.5 CNA402 8A-CD9-625-010 CONN ASSY,6P CD-ME L401 87-003-102-080 COIL, 10UH L404 87-003-152-080 COIL, 100UH
R840 87-029-124-010 RES,FUSE 2.2-1/4 SFR430 87-024-437-080 SFR100K,RH063EC X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
FRONT C.B C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH C603 87-010-319-080 C-CAP,S 56P-50 CH C604 87-010-317-010 CHIP CAP,S 39P CH C605 87-010-264-040 CAP,E 100-10 5L
C606 87-010-805-080 CAP, S 1-16 C607 87-010-452-080 CAPACITOR,1-16 C608 87-010-405-080 CAP, ELECT 10-50V C609 87-010-400-080 CAP, ELECT 0.47-50V C610 87-010-178-010 CAP, S 1000P-50
C611 87-A10-189-040 CAP,E 220-10 C612 87-010-405-080 CAP, ELECT 10-50V C613 87-012-368-080 C-CAP,S 0.1-50 F C614 87-010-312-080 C-CAP,S 15P-50 CH C615 87-010-805-080 CAP, S 1-16
C616 87-010-805-080 CAP, S 1-16 C619 87-010-401-080 CAP,ELECT 1-50V C635 87-018-211-080 CAP,TC U 0.01-50 Z F SA CN601 87-099-033-010 16P 6216 H CN602 87-099-201-010 CONN,8P 6216 H
CN604 8A-CD9-623-010 CONN ASSY,4P KEY JW132 87-003-098-080 COIL,2.2UH JW133 87-003-098-080 COIL,2.2UH L603 87-003-098-080 COIL,2.2UH L604 87-003-098-080 COIL,2.2UH
L605 87-003-098-080 COIL,2.2UH L606 87-003-098-080 COIL,2.2UH L607 87-003-098-080 COIL,2.2UH L608 87-003-098-080 COIL,2.2UH L609 87-003-098-080 COIL,2.2UH
LED602 88-CD6-630-010 LED,934ID RED LED603 88-CD6-630-010 LED,934ID RED LED606 88-CD6-630-010 LED,934ID RED LED607 88-CD6-630-010 LED,934ID RED LED608 88-CD6-630-010 LED,934ID RED
LED610 88-CD6-631-010 LED,934GD GRN LED611 87-CD8-616-010 LED,SA36-11 HWA-11.0 S601 87-A91-704-080 SW,TACT EVQ 214 05R S602 87-A91-704-080 SW,TACT EVQ 214 05R S603 87-A91-704-080 SW,TACT EVQ 214 05R
S604 87-A91-704-080 SW,TACT EVQ 214 05R S605 87-A91-704-080 SW,TACT EVQ 214 05R S609 87-A91-704-080 SW,TACT EVQ 214 05R S611 87-A91-704-080 SW,TACT EVQ 214 05R X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-030-376-080 VIB,CER CSA5.76MG200
TUNER C.B C1 87-010-314-080 C-CAP,S 22P-50V
C2 87-010-318-080 C-CAP,S 47P-50 CH C3 87-010-317-080 C-CAP,S 39P-50 CH C4 87-010-148-080 CAP, 4P-50 C CH GRM C5 87-010-378-080 CAP, ELECT 10-16V
C6 87-010-378-080 CAP, ELECT 10-16V C7 87-018-208-080 CAP 0.047-50F C8 87-010-197-080 CAP, CHIP 0.01 DM C9 87-010-154-080 CAP CHIP 10P C10 87-010-197-080 CAP, CHIP 0.01 DM
NO.
5
Page 6
REF. NO PART NO. KANRI DESCRIPTION
C11 87-010-154-080 CAP CHIP 10P C12 87-010-314-080 C-CAP,S 22P-50V C13 87-010-148-080 C-CAP,S 4P-50 C CH GRM C14 87-012-141-080 0.01-25 K B C2012 C15 87-010-197-080 C-CAP,S0.01-25 K B C 2012
C16 87-010-178-080 CHIP CAP 1000P C17 87-016-669-080 C-CAP,S 0.1-25 K B C18 87-010-197-080 CAP, CHIP 0.01 DM C19 87-010-196-080 CHIP CAPACITOR,0.1-25 C20 87-010-400-080 CAP, ELECT 0.47-50V
C21 87-010-403-080 CAP, ELECT 3.3-50V C22 87-010-197-080 CAP, CHIP 0.01 DM C24 87-010-197-080 CAP, CHIP 0.01 DM C25 87-010-197-080 CAP, CHIP 0.01 DM C26 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C27 87-012-141-080 CHIP-CAPACITOR,0.22-16F C28 87-010-992-080 C-CAP,S 0.047-25 B C29 87-010-992-080 C-CAP,S 0.047-25 B C30 87-010-248-080 CAP, ELECT 220-10V C31 87-010-379-080 CAP, ELECT 22-16V
C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-197-080 CAP, CHIP 0.01 DM C34 87-010-197-080 CAP, CHIP 0.01 DM C35 87-010-197-080 CAP, CHIP 0.01 DM C36 87-010-263-080 CAP,ELECT 100-10V
C37 87-012-155-080 C-CAP 180P-50CH C39 87-010-197-080 CAP, CHIP 0.01 DM C51 87-010-197-080 CAP, CHIP 0.01 DM C56 87-010-152-080 C-CAP,S 8P-50 CH CF1 87-A90-128-010 FLTR,AM IF CFAL-455
CF2 87-008-261-010 FILTER, SFE10.7MA5-A CF3 87-008-261-010 FILTER, SFE10.7MA5-A CN2 87-A60-116-010 CONN,6P HS2M-6WR D13 87-A40-128-080 C-VARI-CAP,HVU202A L2 87-A50-346-010 COIL,FM BPF D
L3 87-A50-350-010 COIL,BAR ANT AMN (COI) L4 87-A50-345-010 COIL,FM RF EX L5 87-A50-342-010 COIL,FM OSC D L6 87-A50-337-010 COIL,AM OSC (TOKO) L7 87-A50-336-010 COIL,AM IFT (TOKO)
L8 87-A50-335-010 COIL,FM IFT (TOKO) L9 87-A50-334-010 COIL,FM DET (TOKO) L10 87-005-849-080 COIL,10UH(CECS) PVC1 87-A91-315-010 TUN-CAP,40P-140P D(TWD) SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06
NO.
REF. NO PART NO. KANRI DESCRIPTION
BATT C.B
VOLTAGE C.B
!
SW901 87-036-389-010 SW,PUSH 1-1-1 R8120125
MOTOR C.B M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P SW1 91-572-085-120 LEAF SW
NO.
HP C.B CN204 87-A60-685-010 CONN,4P H WHT EH
CN605 87-A60-114-010 CONN,4P H S2M-4WR CNA203 8A-CD9-628-010 CONN ASSY,3P MA-HP J251 87-A60-569-010 JACK,HTJ-035-18 S606 87-A91-704-080 SW,TACT EVQ 214 05R
S607 87-A91-704-080 SW,TACT EVQ 214 05R S608 87-A91-704-080 SW,TACT EVQ 214 05R S614 87-A91-704-080 SW,TACT EVQ 214 05R S615 87-A91-704-080 SW,TACT EVQ 214 05R
POWER C.B C901 87-010-192-080 C-CAP,S 0.022-50 F
C902 87-010-192-080 C-CAP,S 0.022-50 F C903 87-010-192-080 C-CAP,S 0.022-50 F C904 87-010-192-080 C-CAP,S 0.022-50 F CNA901 8A-CD9-627-010 CONN ASSY,3P PWR
!
PR901 87-A90-092-080 PROTECTOR,2.5A 491 60V
6
Page 7
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
IC BLOCK DIAGRAM IC, LA1828
A
Resistor Code
Chip resistor
Wattage Type Tolerance 1/16W 1005 5% CJ
1/16W 1/10W
1/8W
1608 2125
3216
5% 5%
5%
Symbol
CJ CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108 118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45 2 1.25 0.45
3.2
1.6
: A : A
IC, M61509FP IC, LA6541D
TRANSISTOR ILLUSTRATION
E C B
2SA1296 2SA1318 2SC1815
E C B
2SA933S 2SC1740S DTC114TS DTC124XS
B C E
2SB1370
C
B
E
2SC2714 DTC114TK DTC114YK DTC114YS DTC144EK
87
Page 8
WIRING-1 (MAIN/CD)
1
A
B
C
D
234567
8
9
10
11 12 13
TP4
(VREF)
14
E
TP3 (RF)
F
G
H
I
TP2
(BIAS)
J
K
109
Page 9
SCHEMATIC DIAGRAM-1 (MAIN/CD 1/2/H.P./POWER)
1211
Page 10
SCHEMATIC DIAGRAM-2 (CD 2/2)
1413
Page 11
WIRING-2 (FRONT/MOTOR)
1
A
B
C
D
234567
8
9
10
11 12 13
14
E
F
G
H
I
J
K
1615
Page 12
SCHEMATIC DIAGRAM-3 (FRONT)
1817
Page 13
SCHEMATIC DIAGRAM-4 (TUNER)
2019
Page 14
WIRING-3 (TUNER)
1
A
234567
IC DESCRIPTION IC, LC78622ED
Pin No. Pin Name I/O Description
1 2
DEFI
TAI
I
Defect detection signal (DEF) input.
I
Test input. A pull-down resistor is built in. Must be connected to 0V. 3 4
B
C
TP6 (R-CH) TP5 (L-CH)
D
E
AM FM (MONO) FM (ST)
5 6 7 8 9
10 11 12 13
14
15 16 17 18
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
T2
CLV+
CLK-
___
V/P
HFL
TES
TOFF
TGL
—
—
—
O
External VCO control phase comparator output.
Internal VCO ground. Must be connected to 0V.
O
PDO output current adjustment resistor connection.
Internal VCO power supply.
I
VCO frequency range adjustment.
Digital system ground. Must be connected to 0V.
O
Slice level control; EFM signal output.
I
Slice level control; EFM signal input.
I
Test input. A pull-down resistor is built in. Must be connected to 0V.
Disc motor control output.
O
Three-value ouput is also possible when specified by microprocessor command.
Rough servo/phase control automatic switching monitor output. Outputs a high level
O
during rough servo and a low level during phase control.
I
Track detection signal input. This is a Schmitt input.
I
Tracking error signal input. This is a Schmitt input.
O
Tracking off output.
O
Tracking gain switching output. Increase the gain when low.
—
—
Track jump output.
O
Three-value output is also possible when specified by microprocessor command.
EFM data playback clock monitor. Outputs 4.3218 MHz when the phase is locked.
O
(Not used)
Synchronization signal detection ouput. Outputs a high level when the synchronization
signal detected from the EFM signal and the internally generated synchronization
O
signal agree. (Not used)
Digital system power supply.
O
Serial data command sled signal output terminal from microprocessor.
Not used.
I
CD pickup inside limit switch.
O
Serial data command sled output terminal from microprocessor.
De-emphasis monitor pin. A high level indicates playback of a de-emphasis disk. (Not
O
used)
O
C2 flag output. (Not used)
O
Digital output (EIAJ format). (Not used)
I
Test input. A pull-down resistor is built in. Must be connected to 0V.
19 20
F
21
22
G
23 24 25
H
I
26 27 28
29
30 31
32, 33
JP+
JP-
PCK
FSEQ
VDD
SL+
SL-
CONT3
PUIN
RW
EMPH
C2F
DOUT
T3, T4
J
34 35 36 37
K
N.C.
MUTEL
LVDD
LCHO
—
—
34Unused. Must be left open.
O
Left channel one-bit D/A converter mute output. (Not used)
Left channel one-bit D/A converter power supply.
O
Left channel one-bit D/A converter output.
2221
Page 15
Pin No. Pin Name I/O Description
38
LVSS
—
Left channel one-bit D/A converter ground. Must be connected to 0V. 39 40 41 42 43 44 45 46 47 48 49
50
51
52
53 54
RVSS RCHO RVDD
MUTER
XVDD XOUT
XIN XVSS SBSY EFLG
PW
SFSY
SBCK
FSX
WRQ RWC
—
—
—
—
Right channel one-bit D/A converter ground. (Must be connected to 0V.)
O
Right channel onr-bit D/A converter output. Right channel one-bit D/A converter power supply.
O
Right channel one-bit D/A converter mute output. (Not used) Crystal oscillator power supply.
O
Connections for a 16.9344 MHz crystal oscillator element.
I
Crystal oscillator ground. (Must be connected to 0V.)
O
Subcode clock synchronization signal output. (Not used)
O
C1, C2, sigle an double error correction monitor. (Not used)
O
Subcode P, Q, R, S, T, U and W output. (Not used) Subcode frame synchronization signal output. This signal falls when the subcode arein
O
standby state. (Not used)
I
Subcode readout clock input. This is a Schmitt input. Output pin for the 7.35 kHZ synchronization signal divided from the crystal oscillator.
O
(Not used)
O
Subcode Q output standby output.
I
Read/write control input. This is a Schmitt input. 55 56
57
58 59 60 61 62
63
64
SQOUT
COIN
___________
CQCK
________
RES
T11
16M
4.2M T5
______
CS
T1
O
Subcode Q output.
I
Command input pin from control microprocessor. Input for both the command input acquisition clock and the SQOUT pin subcode
I
readout clock input pin. This is Schmitt input.
I
Reset input. This pin must be set low briefly after power is first applied.
O
Test output. Leave open. (Normally output a low level). (Not used)
O
16.9344 MHz output. (Not used)
O
4.2336 MHz output.
I
Test input. A pull-down resistor is built-in. (Must be connected to 0V.) Chip seledt input. A pull-down resistor is built-in.(Must be connected to 0V if not
I
controlled.)
I
Test input. No pull-down resistor. (Must be connected to 0V.)
23
Page 16
IC, LA9241ML
Pin No. Pin Name I/O Description
1
FIN2
For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF
O
signal and subtraction from it create an EF signal.
10 11 12 13 14 15 16 17
2
3
4 5
6
7 8 9
FIN1
E
F
TB
TE–
TE
TESI
SCI
TH TA
TD–
TD
JP TO FD
FD–
O
For the connection of the pickup photodiode. For the connection of the pickup photodiode. Subtraction from the F pin creates a TE
O
signal.
O
For the connection of the pickup photodiode.
I
Inputs the DC components in the TE signal.
O
For the connection of a resistor which sets the gain of the TE signal between this pin and the TE pin.
O
TE signal output.
I
TES (track error sense) comparator input.The TE signal is passed through a BPF.
I
Shock detection input.
I
Sets the time constant for the tracking gain.
O
TA amp output.
I
Composes the tracking phase compensation constant between the TD and VR pins.
O
Sets the tracking phase compensation.
I
Sets the amplitude of the tracking jump signal (kick pulses).
O
Tracking control signal output.
O
Focusing control signal output.
I
Composes the focusing phase compensation constant between the FD and FA pins. 18 19 20
21
22 23 24 25 26 27 28 29
30, 31 32, 33
34 35
FA
FA–
FE
FE–
AGND
SP
SPI SPG SP– SPD
SLEQ
SLD
SL–, SL+
JP–, JP+
TGL
TOFF
O
Composes the focusing phase compensation constant between the FD- and FA- pins.
I
Composes the focusing phase compensation constant between the FA and FE pins.
O
FE signal output. For the connection of a resistor which sets the gain of the FE signal between this pin
I
and the TE pin.
O
Ground of analog signals.
O
Single-ended output of the signals input to the CV+ and CV- pins.
I
Spindle amp input.
I
For the connection of a resistor which sets the gain in the spindle 12cm mode.
I
For the connection of the spindle phase compensation constant with the SPD pin.
O
Spindle control signal output.
I
For the connection of sled phase compensation constant.
O
Sled control signal output.
I
Sled feed signal input from the microprocessor.
I
Tracking signal input from the DSP.
I
Tracking gain control signal input from the DSP. Low gain when TGL is “H”.
I
Tracking off control signal input from the DSP. Off when TOFF is “H”.
36
37
38
TES
HFL
SLOF
O
TES signal output to the DSP. The HFL (high frequency level) signal is used to judge whether the main beam is
O
positioned on the pit or on the mirror.
I
Sled servo off control input.
24
Page 17
Pin No. Pin Name I/O Description
39, 40
CV–, CV+
I
CLV error signal input from the DSP.
41
42
43
44 45 46 47 48 49 50 51 52 53 54
55
RFSM
RFS–
SLC
SLI
DGND
FSC
TBC
NC
DEF
CLK
CL
DAT
CE
DRF
FSS
—
—
O
RF output. Sets the RF gain and the EFM signal’s 3T compensation constant together with the
O
RFSM pin. The SLC (slice level control) signal is output to control the DSP’s data slice level of
O
the RF waveform.
I
Input to control the DSP’s data slice level. Ground of digital signals.
O
Output for the focus search smoothing capacitor.
I
The TBC (tracking balance control) signal sets the EF balance variation range. Not connected.
O
Disc defect detection output.
I
Reference clock input. 4.23 MHz is input from the DSP.
I
Microprocessor command clock input.
I
Microprocessor command data input.
I
Microprocessor chip enable input.
O
DRF (detect RF) is an output to detect the RF level. The FSS (focus search select) signal switches the focus search modes (+/-search /
I
+search with respect to the reference voltage). 56 57 58 59 60 61 62 63 64
VCC2
REFI
VR LF2 PH1
BH1
LDD
LDS
VCC1
— —
— — —
—
VCC of servo and digital circuits. For the connection of bypass capacitor for the reference voltage.
O
Reference voltage output. Sets the time constant for disc defect detection. For the connection of a capacitor to hold the RF signal peak. For the connection of a capacitor to hold the RF signal bottom.
O
APC circuit output.
I
APC circuit input. VCC of RF signal circuits.
25
Page 18
IC, LC865516A-5L26
Pin No. Pin Name I/O Description
1
SEG E
O
SEG E control.
10 11 12 13 14 15 16 17 18
2 3 4 5 6 7 8 9
SEG F
SEG G
NC
I-RES
XT1 (IN)
NC
XT2 (OUT)
VSS
CF1 (IN)
CF2 (OUT)
VDD I-KEY0 I-KEY1
I-MOTOR
I-CDSW
O-SHIFT
NC
O
SEG F control.
O
SEG G control.
—
Not connected.
I
Microprocessor reset input.
I
Connected to an external 32.768 kHz crystal oscillator.
—
Not connected.
O
Connected to an external 32.768 kHz crystal oscillator.
—
GND.
I
Connected to an external 5.76 MHz ceramic filter.
O
Connected to an external 5.76 MHz ceramic filter.
—
Microprocessor power supply (+5 V).
I
Key AD input. (AD)
I
Key AD input. (AD)
I
Deck status input. (AD)
I
CD door switch status input.
O
Main clock shift output.
—
Not connected. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
O-BASS LED
O-QS CONT
O-SFT LED
I-DRF
I-WRQ
NC
I-REM
O-CD ON
O-TU ON
O-P.CONT
NC O-BEAT O-MUTE O-DIGIT
O-SEG REPEAT
O-COIN
I-SQOUT
O
BASS LED ON/OFF control output. (Not used)
O
Q sound LED ON/OFF control output.
—
Not used.
I
CD RF level detection input.
I
CD subcode Q standby input.
—
Not connected.
I
Remote control input.
O
CD power control output.
O
TU power control output.
O
The main power supply control output.
—
Not connected.
O
Beat sw control output.
O
Main mute output.
O
7-segment LED power supply control output.
O
REPEAT LED ON/OFF control output.
O
CD command output.
I
CD subcode Q input. 36 37 38 39 40 41
O-CQCK
O-RWC
O-DATA O-CD LED O-TU LED O-TA LED
O
CD command/CLK for subcode.
O
CD read/write control output.
O
Data output to M61509FP.
O
LED ON/OFF control output for the CD function.
O
LED ON/OFF control output for the TU function.
O
LED ON/OFF control output for the TA function. (Not used)
26
Page 19
Pin No. Pin Name I/O Description
42
NC
—
Not connected. 43 44 45 46 47 48
SEG DP
SEG A SEG B SEG C SEG D
NC
—
O O O O O
SEG DP control.
SEG A control.
SEG B control.
SEG C control.
SEG D control.
Not connected.
27
Page 20
ELECTRICAL ADJUSTMENT
D TUNER C .B
4
L006
PVC001
1
TC003 TC004
2 5
L005
TC001
TC002
TP6 (RCH)
123456
TP5 (LCH)
L009
6
IC001
L007
3
L008
6
L004
< RADIO SECTION >
1. AM Frequency Range Adjustment Settings: • Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L006, TC003
L006 ....................................................................... 517kHz
TC003................................................................... 1750kHz
2. AM Tracking Adjustment Settings: • Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003, TC004
L003 ....................................................................... 600kHz
TC004................................................................... 1400kHz
L003
2
5. FM Tracking Adjustment Settings: • Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L004, TC002
L004 ........................................................................88MHz
TC002....................................................................108MHz
6. FM IF Adjustment Settings: • Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L008, L009
L008, L009 ........................................................... 10.7MHz
3. AM IF Adjustment Settings: • Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L007
L007 ....................................................................... 455kHz
4. FM Frequency Range Adjustment Settings: • Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L005, TC001
L005 ........................................................................87MHz
TC001....................................................................109MHz
28
Page 21
B CD C.B
1
TP4
IC404
1
SFR430
A MAIN C.B
TP3
IC401
L801
TP2
2
3
< CD SECTION >
1. Focus Bias Adjustment Make the focus bias adjustment when replacing and repairing the optical block.
Oscilloscope
(DC range)
TP3 (RF)
TP4 (VREF)
1) Connect an oscilloscope to the test point TP3 (RF) and
TP4 (VREF).
2) Turn on the power switch.
3) Insert test disc TCD-782 (YEDS-18) and play back the
second composition.
4) Adjust SFR430 so that RF signal of the test point TP3
(RF) is MAX and CLEAREST.
EYE PATTERN must be CLEAR and MAX
VOLT / DIV: 200mV
TIME / DIV: 0.5 s
< TAPE RECORDER SECTION >
2. Bias Adjustment Settings: • Test tape: TTA-630
• Test Point: TP2
• Adjustment location: L801
L801 .............................................................. 85kHz±2kHz
3. Azimuth Adjustment Condition: • Test tape: TTA-320
• Test point: PHONE JACK
• Adjustment location: Azimuth adjustment screw
Method: Play back the test tape and adjust the screw so
that the output is maximum.
MAX
0V
29
Page 22
MECHANICAL PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 87-B00-010-010 BADGE,AIWA 30.5-5.2 S 2.5L 2 8A-CD9-009-010 WINDOW,CASS 3 8A-CD9-232-010 SPR-T,CASS 4 8A-CD9-008-010 BOX,CASS 5 8A-CDK-001-010 WINDOW,LED RC
6 84-CD5-216-010 BRACKET 7 84-CD5-215-010 GEAR 8 8A-CD9-062-010 CABI,FR B1 ASSY 9 88-CD5-602-010 SPKR 4’3.2 10 8A-CD9-222-010 HLDR,SPEAKER
11 8A-CD9-026-010 KNOB,RTRY TU 12 8A-CD9-034-010 WINDOW,TU U 13 8A-CD9-022-010 LENS,LED 14 8A-CD9-020-010 BTN,REPEAT 15 8A-CD9-017-010 BTN,QSOUND
16 8A-CD9-021-010 BTN,EQ 17 8A-CD9-203-010 GUIDE,VOL 18 8A-CD9-014-010 BTN,VOL 19 8A-CD9-013-010 PANEL,VOL 20 8A-CD9-622-010 FF-CABLE, 8P CD-FR
21 8Z-CH4-212-010 RING,CHUCK 22 8Z-CH4-211-010 BASE,CHUCK 23 87-036-368-010 MAGNET 24 84-CD5-217-010 PLATE,MAGNET 25 8Z-CH4-225-010 HLDR,CHUCK A(S)
26 8A-CD9-007-010 WINDOW,CD 27 8A-CDK-003-010 BOX,CD K-LH 28 8A-CD9-231-010 SPR-T,CD 29 8A-CD9-005-010 CHAS,CD A 30 87-036-389-010 SW,PUSH LOCK
31 8Z-CDB-169-010 PANEL,CD SANYO 32 8A-CD9-202-010 GUIDE,LED 33 8A-CD9-023-010 POINTER,TU 34 8A-CD9-207-010 GEAR,TU B 35 8A-CD9-206-010 GEAR,TU A
36 8A-CD9-208-010 DRUM,TU 37 8A-CD9-209-010 LEVER,BAND A 38 8A-CD9-205-010 GUIDE,GEAR 39 8A-CH4-209-010 HLDR,PT
!
40 8A-CD9-604-010 PT,H 4.5WT04541A
NO.
REF. NO PART NO. KANRI DESCRIPTION
41 8Z-CD5-634-010 COVER,AC SOCKET
!
42 87-A60-178-010 JACK,AC E W/SW 43 8A-CD9-012-010 HANDL,GRIP 44 8A-CD9-011-010 HANDL,ARM 45 8Z-CH4-640-010 ANT,ROD
46 8A-CD9-027-010 KNOB,SL BAND 47 8A-CD9-004-010 CABI,REAR B1 48 8A-CD9-010-010 LID,BATT 49 8A-CD9-221-010 HLDR,ANT 50 87-CD6-213-010 SPR-C,BATT (-)
51 8A-CD9-211-010 HLDR,PWB L 52 8A-CD9-212-010 HLDR,PWB R 53 8A-CD9-223-010 SPR-P,REC TN21 54 8A-CD9-024-010 KEY,CASS TN21 55 86-CT4-218-010 CUSHION,FOOT/PORON
56 8A-CD9-201-010 HLDR,DISPLAY 57 8A-CD9-620-010 FF-CABLE, 16P FR-MAIN 58 8A-CD9-621-010 FF-CABLE, 16P CD-RF 59 8A-CD9-660-010 BAR,ANT MW 2B-AC0
!
60 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700 61 8A-CD9-018-010 CAP, CD A
62 8A-CD9-019-010 CAP, CD B 63 8A-CH4-211-010 COVER, HLDR PT A 87-B10-242-010 UT2+3-30 W/O CR B 87-741-096-410 UT2+3-10
C 87-B10-239-010 QT2+3-8 W/O CR D 87-661-097-410 TAPPING SCREW, VFT1+3-12 E 87-751-094-410 VT2+3-6 W10SL0T F 87-067-566-010 TAPPING SCREW, VFTT+3-6 G 87-571-033-410 TAPPING SCREW, VIT+2-4
H 87-255-096-410 U+3-10 NI I 87-342-074-010 UT2+2.6-8 J 87-B10-269-010 UT2+3-12 W/O CR K 87-352-075-210 VT2+2.6-10 L 87-WA5-253-010 W,3.3-10-0.8
M 87-661-095-410 VFT1+3-8 N 87-251-073-410 SCREW,U+2.6-6
NO.
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
30
Page 23
MECHANICAL EXPLODED VIEW 1/1
43
GRILLE, FRONT L
17
54
60
45
A
J
F
P.C. B
50
49
B
P.C. B
P.C. B
38
J
36
51
B
B
B
P.C. B
58
B
B
57
52
50
P.C. B
57
20
E
B
B
E
B
55
P.C. B
46
A
H
A
47
48
26
44
25
24
19
18
B
B
10
C
C
10
C
10
9
5
23
C
P.C. B
14
61
22
21
30
13
12
27
29
DA11T3C
31
15
C
41
28
B
6
L
I
16
62
L
I
56
CHAS,TU
33
32
39
7
63
P.C. B
K
40
63
D D
D
D
34
35
C
C
C
K
42
37
M
N
10
C
10
C
C
10
TN-21ZVC-2000
G
53
3231
4
2
1
3
GRILLE, FRONT R
6
7
7
55
11
9
Page 24
TAPE MECHANISM EXPLODED VIEW 1/1
F
G
1
E
2
8
10
J L
14
b
18
19
7
36
46
47
25
9
21
20
22
23
24
c 51
26
27
28
A
6
29
LUG PLATE
52
4
3
a
15 16
17
34
35
37
TAPE MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 S1-921-030-4A0 HEAD BASE 2 S1-821-030-070 AZIMUTH SPRING 3 S1-921-030-090 PANEL P SPRING
5
11
12
13
31
49
30
32
c
b
33
A
4 S1-921-260-050 GEAR PLATE SPRING 5 S1-921-265-020 GEAR PLATE ASSY
6 S1-510-020-020 REC SPRING PLATE 7 S1-921-015-010 CHASSIS ASSY 8 S1-921-030-110 HEAD PANEL 9 S1-921-143-160 BASE ASSY 10 S1-921-141-8A0 M CONTROL SPRING
11 S1-921-260-4A0 SENSING LEVER 12 S1-921-043-100 PINCH ROLLER ARM ASSY 13 S1-921-130-010 EJECT SLIDE LEVER 14 S1-921-141-3A0 P CONTROL SPRING 15 S1-921-140-550 PAUSE LEVER(E)
16 S1-921-140-120 PAUSE LEVER SPRING 17 S1-921-140-110 PAUSE STOPPER 18 S1-921-140-150 BUTTON LEVER SPRING(B) 19 S1-821-011-590 E KICK LEVER 20 S1-921-141-070 BUTTON LEVER SPRING(A)
21 S6-401-011-490 LEAF SW MSW-1541T 22 S1-921-140-090 SWITCH ACTUATOR 23 S1-921-140-080 PUSH BUTTON ACTUATOR 24 S1-921-140-190 PLAY BUTTON LEVER 25 S1-921-030-100 MG ARM SPRING
26 S1-921-140-040 REW BUTTON LEVER 27 S1-921-140-050 FF,BUTTON REVER 28 S1-921-140-060 STOP BUTTON LEVER 29 S1-921-140-600 PAUSE BUTTON LEVER 30 S1-821-100-700 FF GEAR
31 S1-921-050-060 SENSER 32 S1-921-053-100 TAKE UP REEL ASSY 33 S1-829-100-010 PACK SPRING 34 S1-921-050-150 S REEL HUB 35 S1-921-050-220 BACK TENSION SPRING
NO.
a
C
48
C
REF. NO PART NO. KANRI DESCRIPTION
36 S1-921-140-030 REC BUTTON LEVER 37 S1-921-140-170 P.S.LEVER SPRING 38 S1-921-073-040 RF CLUTCH ASSY 39 S1-921-070-030 RF BELT 40 S1-921-260-020 CAM GEAR
41 S1-921-140-160 E ACTUATOR SPRING 42 S1-921-093-210 FLYWHEEL ASSY 43 S1-921-090-380 MAIN BELT 44 S1-921-120-590 MOTOR PULLEY 45 S6-002-030-220 MOTOR EG530AD-2B
46 S6-209-100-100 E HEAD PH-K380-MS1 47 S1-921-030-050 MG ARM 48 S1-921-140-210 REC BUTTON LEVER SPRING 49 S1-821-100-690 RECORD SAFETY LEVER 50 S1-821-128-9A0 MOTOR BRACKET
51 S1-821-010-500 PLAY BUTTON LEVER SPRING 52 S6-201-011-110 HEAD,RP7442ES-0951 A S9-P04-200-310 C TAPPING SCREW 2-3 B S1-921-120-020 MOTOR COLLER SCREW C S9-B10-200-510 P TAPPING BIND SCREW M2-5
D S9-C07-204-510 SCREW,TAPPING(CAMERA)M2-4.5 E S9-P01-200-610 SCREW,M2-6 F S9-B01-200-310 (+)BIND SCREW M2-3 G S9-F08-200-710 AZIMUTH SCREW M2-7 H S1-921-120-030 MB SCREW
I S9-W02-300-100 P WASHER CUT 1.2-3.8-0.3 J S9-W02-500-100 P WASHER CUT 1.45-3.8-0.5 K S9-W01-400-100 P WASHER 2-3.5-0.4 L S9-W01-130-200 P WASHER 2.1-4-0.13
NO.
38
39
42
43
D
40
D
K
41
I
B
B
50
H
44
45
3433
Page 25
CD MECHANISM EXPLODED VIEW 1/1
SHAFT,SLIDE
B
SF-P101NR
CHASSIS
B
1
2
A
A
3
SPINDLE MOTOR(M1)
CD MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 S2-121-A28-400 COVER GEAR 2 S2-511-A21-000 GEAR MIDDLE 3 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
MOTOR C,B
35
Page 26
2–11, IKENOHAT A 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
920074
Printed in Singapore
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use