AirLive POE-FSH2422G-250 User Manual

POE-FSH2422G-250

24 Port 802.3af PoE Web Smart Switch

User’s Manual

No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp.

OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution. All information is subject to change without notice

All Trademarks are properties of their respective holders.

AirLive POE-FSH2422G-250 User’s Manual

FCC Statement

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

z Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

IMPORTANT NOTE

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

AirLive POE-FSH2422G User’s Manual

Table of Contents

1. Introduction ...............................................................................................1

1.1 Overview................................................................................................................1

1.2 Guide to the Chapters............................................................................................1

1.3 Quick Setup ...........................................................................................................2

1.4 Installation Steps....................................................................................................3

1.5 Comparison Chart..................................................................................................4

2. Installation of the Switch...........................................................................................6

2.1 Unpack the Package..............................................................................................6

2.2 Hardware Overview................................................................................................7

2.3 Installation Site Preparation...................................................................................9

2.4 Rack Mounting.......................................................................................................9

2.5 Desktop Installation..............................................................................................11

2.6 Cabling Requirements..........................................................................................11

2.7 Connecting to Power............................................................................................12

2.8 Reset to Default ...................................................................................................13

3. LED Indicators .........................................................................................14

3.1 Comprehensive LEDs..........................................................................................14

3.2 LED Table.............................................................................................................14

4. Web Management ....................................................................................15

4.1 Setup your computer for Web management.........................................................15

4.2 Remote Management...........................................................................................17

4.3 Get into the Web Management ............................................................................19

4.4 Administrator........................................................................................................20

4.5 Authentication Configuration (Administrator menu)..............................................20

4.6 System IP Configuration (Administrator menu).................................................... 21

4.7 System IP Configuration (Administrator menu).................................................... 22

4.8 Load default setting (Administrator menu) ...........................................................22

4.9 Firmware Update (Administrator menu)...............................................................23

4.10 Reboot Device (Administrator menu).................................................................23

4.11 Port Management...............................................................................................24

4.12 Port Configuration (Port Management menu) ....................................................24

4.13 Port Mirroring (Port Management menu)............................................................26

iii

AirLive POE-FSH2422G-250 User’s Manual

Table of Contents

4.14 Bandwidth Control (Port Management menu)....................................................26

4.15 Broadcast Storm Control (Port Management menu)..........................................27

4.16 POE (Port Management menu) ..........................................................................28

4.17 VLAN Setting......................................................................................................28

4.18 VLAN Mode (VLAN Setting)...............................................................................29

4.19 VLAN Member (VLAN Setting)...........................................................................30

4.20 Multi to 1 Setting (VLAN Setting)........................................................................31

4.21 Per Port Counter................................................................................................32

4.22 Trunking.............................................................................................................32

4.23 QoS Setting........................................................................................................33

4.24 Priority Mode (QoS Setting) ...............................................................................34

4.25 Port, 802.1p, IP/DS based (QoS Setting)...........................................................34

4.26 TCP/UDP Port Based (QoS Setting)..................................................................35

4.27 Security..............................................................................................................35

4.28 MAC Address Binding (QoS Setting)..................................................................35

4.29 TCP/UDP Filter (QoS Setting)............................................................................36

4.30 Spanning Tree....................................................................................................37

4.31 STP Bridge Settings (QoS Setting)....................................................................38

4.32 STP Port Settings (QoS Setting)........................................................................39

4.33 Loopback Detection Settings (QoS Setting).......................................................40

4.34 Backup/Recovery...............................................................................................40

4.35 Miscellaneous ....................................................................................................41

4.36 SNMP.................................................................................................................41

4.37 Logout................................................................................................................42

Appendix A: Product Specifications...............................................................43

Appendix B: Troubleshooting .......................................................................45

AirLive POE-FSH2422G User’s Manual

1. Introduction

1.1 Overview

The POE-FSH2422G-250 is a Power Control POE Switch, and total power is 250W. This switch provides 24 10/100Mbps RJ-45 ports and can support 2 Combo Gigabit RJ-45/SFP to uplink. This web-smart switch includes auto-MDI/MDIX crossover detection function. 24 of those ports are all built with PoE functionality, pr oviding the ultimate choice in network flexibility. With this added PoE feature, this switch is an ideal solution for building wireless, IP surveillance, and VoIP networks.

It also provides port-based and 802.1Q tag VLAN function to provide better traffic management, reduces latency, improve security and save bandwidth. This is also a cost-saving feature as it reduces the need to add additional hardware to the network.

These 24 10/100Mbps RJ-45 support the IEEE 802.3af PoE protocol. Each port and transmit a maximum power 15.4 watts. User can also enable or disable power supply on PoE ports from UI.

Notice:  This switch is using 48V 802.3af PoE standard. It does not work with passive PoE. Do

not connect with passive PoE devices

 When plug in the mini-GBIC module, the device will activate mini-GBIC, and the RJ45

port will be disabled.

1.2 Guide to the Chapters

 Chapter 1: Introduction and Quick Setup guide. All the essential information

including IP Address and Password information are in the Quick Setup section.

 Chapter 2: Detail installation instruction including module information and how to

make Cat. 5 Cable

 Chapter 3: LED indicators  Chapter 4: Detail information on Web management including how to setup remote

management.

AirLive POE-FSH2422G-250 User’s Manual

1. Introduction

1.3 Quick Setup

Power-On the switch

 The POE-FSH2422G-250 Switch has a built-in power supply to operate with 100 ~

240V AC, 50 ~ 60Hz power source.

 The AC power cord connector is located at the rear of the unit and the On/Off switch is

next to the connector.

 After the Switch is powered on, it will perform “self-diagnostic” test. This process takes

about 10 seconds to complete.

Important Information

work with passive PoE. Do not connect with passive PoE devices.

rotect from potential power surge.

LED Table

LED Status Description No. Of LED

The default IP address: 192.168.2.1 The default username is admin The default password is airlive This switch is using 48V 802.3af PoE standard. It does not

It is recommended that you install the switch with an UPS to

Power On Power on Power

On Link 1000Mbps

1000M

2 (25~26)

Off Link 10/100Mbps On Link 26 (1~26)

Link/ ACT

Flashing Data activating 26 (1~26)

24 (1~24)

Device

PoE

No Power Device is

Port is linked to Power

Off

24 (1~24)

connected

AirLive POE-FSH2422G-250 User’s Manual

1. Introduction

1.4 Installation Steps

This section lists the installation procedures in steps. Each step’s instruction is thoroughly explained in the subsequent sections of this chapter.

Step 1: Connect your device's PoE port to the switch's POE port. The Gigabit ports are not PoE ports.

Step 2: Connect your device's PoE port to the switch's POE port (see Figure A). The Gigabit ports are not PoE ports.

AirLive POE-FSH2422G-250 User’s Manual

1. Introduction

Step 3: If you want to install the switch on the 19" rack, please install the mounting kit according to Figure C.

Step 4: Your PoE device should get the power from the switch now. If you want to change settings via web management. Please follow the instructions below.

Step 5: Set your PC's IP address to 192.168.2.50.

Step 6: Open your web browser and enter "192.168.2.1" to get into the switch's web management.

Step 7: Enter "admin" for username. "airlive" for password.

Step 8: Please check the following chapters for more detailed configurations

1.5 Comparison Chart

Model POE-FSH-2422G-250 POE-FSH2422G-390 Power

250 Watts (Max) 390 Watts (Max) Consumption Power Input 100~240V/AC, 50~60Hz Max supply PoE Power

15.4Watts per Port, 250

Watts totally per Device Dimensions 445 × 220 × 45 mm (L x

W x H)

AirLive POE-FSH2422G-250 User’s Manual

15.4Watts per Port, Full Power

440 × 332 × 44 mm (L x W x H)

Weight 2.54 kg 4.7 kg

1. Introduction

Operating

0 to 45℃ Temperature Storage

-20 to 90℃ Temperature Humidity 10 to 90% RH (non-condensing) Certifications FCC Class A, CE

AirLive POE-FSH2422G-250 User’s Manual

2. Installation of the Switch

2. Installation of the

This chapter provides the detailed instructions for installation of the switch. For concise installation instruction, the previous chapter’s “Quick Setup” section provides all the important information including IP address, password, and LED table for user’s reference.

Switch

2.1 Unpack the Package

Before you begin the installation of POE-FSH2422G-250 Management Switch, make sure that you have all the necessary accessories that come with your package. Follow the steps below to unpack your package contents:

 Clear out an adequate space to unpack the package carton.  Open the package carton and take out the contents carefully.  Put back all the shipping materials such as plastic bag, padding and linings into the

package carton and save them for future transport need.

After unpacking and taking out the entire package contents, you should check whether you have got the following items:

 POE- FSH2422G-250 24-Port 802.3af PoE Switch  One AC power cord  Quick Install Guide  Support CD-ROM (The PDF version of this User’s Manual can be found within)  One pair Rack-mount kit + 8 Screws

If any of these above items is missing or damaged, please contact your local dealer for replacement.

AirLive POE-FSH2422G-250 User’s Manual

2. Installation of the Switch

2.2 Hardware Overview

Front Panel

The front panel of the web smart switch consists of 24 10/100Base-TX RJ-45 ports and 2 combo gigabit uplink RJ-45/SFP ports. The LED Indicators are also located on the front panel.

LED Indicators: Comprehensive LED indicators display the status of the switch and the network (see the

LED Indicators chapter below).

100BASE-TX Fast Ethernet PoE Ports (Port 1~24): These ports are PoE enable ports. These PoE ports will be automatically activated when a

compatible terminal is identified, and the PoE port will supply power to the connected PoE device.

For legacy devices that are not yet compatible, the PoE port will not offer the power to these devices. This feature allows users to freely and safely mix legacy and Power over Ethernet compatible devices on their network.

These ports support network speeds of either 10Mbps or 100Mbps, and can operate in halfand full- duplex transfer modes. These ports also support the automatic MDI/MDIX crossover detection function, providing true “plug and play” capability. Just plug-in the network cable to the hub directly and regardless if the end node is a NIC (Network Interface Card) or switch and hub.

AirLive POE-FSH2422G-250 User’s Manual

2. Installation of the Switch

1000BASE-T Gigabit Ethernet Ports (Port 25~26): The Switch provides two Gigabit twisted pair ports, supported auto negotiable

10/100/1000Mbps and auto MDI/MDIX crossover detection function, this function gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and don’t care if the end node is NIC (Network Interface Card) or switch and hub. These ports can operate in half-duplex mode for 10/100Mbps and full- duplex mode for 10/100/1000Mbps.

Note: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.

Combo mini-GBIC Ports (Port 25~26) The Switch is equipped with two combo mini-GBIC ports, supported optional

1000BASE-SX/LX mini-GBIC module. The 1000BASE-T port 25 and 26 are the same ports with the mini-GBIC port 25 and 26, when plug in the mini-GBIC module, the device will activate mini-GBIC, and the RJ45 port will be disabled.

Reset: The Reset button is to reset all the setting back to the factory default. Note: Be sure that you recorded the setting of your device, else all the setting will be erased

when pressing the “Reset” button.

The Rear Panel

The 3-pronged power plug is placed at the rear panel of the switch right side shown as below.

AirLive POE-FSH2422G-250 User’s Manual

2. Installation of the Switch

2.3 Installation Site Preparation

You can mount POE-FSH2422G-250 24-Port 802.3af PoE Switch either on desktop or on a 19-inch rack. If you plan to mount the switch on desktop, please choose a steady, level surface in a well-ventilated area that is free from excessive dust. In any case, the installation site chosen for your switch has to comply with the following requirements:

 The surface where you want to mount the switch must be able to sustain at least 2.5kg.  Do not place heavy objects (more than 3kg) on top of the switch.  The location must preferably be free from excessive dust, away from heat vent, hot-air

exhaust and direct sunlight.

 The switch should not be placed near large electric motors or other strong

electromagnetic sources. As a reference, the strength of the electromagnetic field on site should not exceed the (RFC) standards for IEC 801-3, Level 2(3V/M) field strength.

 The air temperature in the location should be within a range of 0 to 45°C.  The relative humidity in the location should not exceed 95% non-condensing humidity.  The distance between the RJ-45 port and the standard network interface should not

exceed 100 meters.

 Adequate space should be allowed in front of all the ports, so that each port is easily

accessible for cable connections.

 Leave at least 10cm(4 inch) of space around the switch to allow heating dissipation

2.4 Rack Mounting

The POE-FSH2422G-250 PoE Switch can be mounted on a standard size 19-inch rack, which can in turn be placed in a wiring closet with other equipments.

Before you can mount the switch on the rack, first you must attach the mounting brackets on both sides of the switch with screws, and then mount it as a unit on the rack.

AirLive POE-FSH2422G-250 User’s Manual

To mount the unit on a rack, please follow the steps below:

Step 1. First, align the holes on the bracket with the holes on both side of the

switch.

Step 2. Insert screws into the holes and then fasten the bracket on one side of the

switch with a screwdriver. Step 3. Repeat Step 1 and 2 to fasten the bracket on the other side of the switch. Step 4. Mount the unit on the rack and align the notches on both brackets with

mounting holes on the rack, and then secure the unit with suitable screws.

2. Installation of the Switch

AirLive POE-FSH2422G-250 User’s Manual

2. Installation of the Switch

2.5 Desktop Installation

The POE-FSH242G-250 PoE Switch has four rubber pads attached on each corner of its underside. These pads serve as cushioning against vibration and prevent the switch from sliding off its position. They also allow adequate ventilation space when you place the switch on top of another device.

 The location you choose to install your switch and the way you configure your network

may greatly affect its performance. Please see the previous section for “installation site” preparation.

 Do not place more than 3kg (6.6lbs) of weight on the top of the switch.  Leave at least 10cm (4 inch) of space around the switch to allow proper heating

dissipation.

2.6 Cabling Requirements

For 100BASE-TX and 1000Base-T ports

The 24 RJ-45 station ports and the 1000Base-T ports of the optional Gigabit-Copper module require Cat. 5 twisted-pair UTP/STP cable for connection. When configuring within the 10/100/1000BASE-T cabling architecture, the cable distance should be within 100m.

AirLive POE-FSH2422G-250 User’s Manual

+ 35 hidden pages