Airlive AC-1200UR User Manual

AC-1200UR

1200Mbps 802.11AC

AP Router with USB

User’s Manual

Table of Contents

No part of this publication may be reproduced in any form or by any means, whether electronic, mechani cal , photocopying, or recording without the written consent of OvisLink Corp.

OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution. All information is subject to change without notice

All Trademarks are properties of their respective holders.

This product requires professional installation. Please do not attempt to install the device without the necessary knowledge in regards to your country's wirelessregulations.

i AirLive AC-1200UR User’s Manual

Table of Contents

Regulatory Infor mati on

Federal Communication Com mi s s ion Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecti on ag ai nst harmful interference in a residential installation. This equipment generates, uses and can r adiate radio freq uency energy and, i f not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recepti on, w hic h can be det ermine d by turning the eq uip ment o ff and o n, th e user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the foll owing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

AirLive AC-1200R User’s Manual

Table of Contents

IMPORTANT NOTE

FCC Radiation Exposure St a t eme nt:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be professionally installed to ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the Uni ted St ates. The use o f the sy stem in a ny other combina tion (s uch as co-located antennas transmitting the same information) is expressly forbidden.

iii AirLive AC-1200UR User’s Manual

Table of Contents

1. Introduction ............................................................................................. 1

1.1 Overview............................................................................................ 1

1.2 Firmware Upgrade and Tech Support ................................................ 2

1.3 Wireless Operation Modes ................................................................. 2

1.3.1 Dual Band Router Mode ............................................................................................ 2

1.3.2 Dual AP Mode ............................................................................................................ 4

1.3.3 WISP + AP Mode ....................................................................................................... 5

1.3.4 Bridge + AP Mode ..................................................................................................... 6

1.3.5 Client + AP Mode ...................................................................................................... 7

2. Installing the AC-1200UR ........................................................................ 9

2.1 Before You Start................................................................................. 9

2.2 Installing AC-1200UR ........................................................................ 9

2.3 Knowing Y our AC-1200UR ............................................................... 10

2.3.1. Front Side Introduction ...................................................................................... 10

2.3.2. Back Side Introduction ...................................................................................... 11

2.4 Installati onSteps .............................................................................. 12

2.4.1. Installation Steps by using LAN port ................................................................. 12

2.4.2. Wireless Installation Steps ................................................................................. 13

2.4.3. Internet Installation Steps .................................................................................. 16

3. Configuring the AC-1200UR ................................................................. 18

3.1 Important Information ....................................................................... 18

3.2 Prepare Your PC .............................................................................. 19

3.3 Management Interface ..................................................................... 20

3.3.1 Web Management (HTTP): ...................................................................................... 20

3.4 Introduction to Web Management .................................................... 20

3.4.1 Getting into Web Management ................................................................................ 20

3.4.2 Login ........................................................................................................................ 20

3.5 Initial Configuration .......................................................................... 21

3.5.1 Choose the wireless Operation Modes ..................................................................... 21

3.5.2 Change the Device’s IP Address .............................................................................. 22

3.5.3 Change the Country Code ........................................................................................ 23

3.5.4 Set the Time and Date .............................................................................................. 24

AirLive AC-1200R User’s Manual

Table of Contents

3.5.5 Change Password ..................................................................................................... 24

4. Wireless and WAN Settings ................................................................. 25

4.1 About AC-1200UR Menu Structure .................................................. 25

4.2 General Wireless Settings ............................................................... 26

4.2.1 Regulatory Domain .................................................................................................. 28

4.2.2 Network SSID .......................................................................................................... 28

4.2.3 Site Survey ............................................................................................................... 29

4.2.4 Radio Mode .............................................................................................................. 30

4.2.5 Channel .................................................................................................................... 30

4.2.6 Channel Width ......................................................................................................... 31

4.2.7 Security Settings ...................................................................................................... 31

4.2.8 Advance Settings ...................................................................................................... 34

4.2.9 Access Control (ACL) .............................................................................................. 36

4.2.10 Multiple SSID ........................................................................................................ 37

4.2.11 QoS Setting ............................................................................................................ 38

4.2.12 Bandwidth Control ................................................................................................. 40

4.3 AP Specific Settings ......................................................................... 42

4.4 Bridge ModeSpecific Settings .......................................................... 43

4.5 Client Mode Specific Settings .......................................................... 44

4.6 Router Mode Specific Settings ......................................................... 46

4.6.1 WAN Port Settings ................................................................................................... 47

4.6.2 DHCP Server Settings .............................................................................................. 49

4.6.3 Multiple DMZ .......................................................................................................... 50

4.6.4 Virtual Server Settings ............................................................................................. 51

4.6.5 Special Applications ................................................................................................. 52

4.6.6 IP Filtering Settings ................................................................................................. 53

4.6.7 Dynamic DNS Settings ............................................................................................ 54

4.6.8 Remote Management Settings ................................................................................. 54

4.7 WISP Specific Settings .................................................................... 55

4.7.1 WAN Port Settings ................................................................................................... 56

4.7.2 DHCP Server Settings .............................................................................................. 58

4.7.3 Multiple DMZ .......................................................................................................... 59

4.7.4 Virtual Server Settings ............................................................................................. 60

4.7.5 Special Applications ................................................................................................. 61

4.7.6 IP Filtering Settings ................................................................................................. 62

4.7.7 Dynamic DNS Settings ............................................................................................ 63

v AirLive AC-1200UR User’s Manual

Table of Contents

4.7.8 Remote Management Settings ................................................................................. 63

5. System Configurati on ........................................................................... 64

5.1 System Configuration ...................................................................... 64

5.1.1 Device IP Settings .................................................................................................... 64

5.1.2 Time Settings ........................................................................................................... 65

5.1.3 Password Settings .................................................................................................... 66

5.1.4 System Management ................................................................................................ 67

5.1.5 WAN......................................................................................................................... 68

5.1.6 2.4G Wireless ........................................................................................................... 68

5.1.7 5G Wireless .............................................................................................................. 74

5.1.8 USB .......................................................................................................................... 75

5.1.9 QoS .......................................................................................................................... 79

5.1.10 NAT ........................................................................................................................ 80

5.1.11 Firewall .................................................................................................................. 81

6. Device Status & Tools........................................................................... 83

6.1 Status .............................................................................................. 83

6.1.1 Status ........................................................................................................................ 83

6.1.2 Internet Connection .................................................................................................. 83

6.1.3 Device Status ........................................................................................................... 84

6.1.4 System Log .............................................................................................................. 85

6.1.5 Security Log ............................................................................................................. 85

6.1.6 Active DHCP Client ................................................................................................. 86

6.1.7 Statistics ................................................................................................................... 86

6.1.8 Configuration T ools ................................................................................................. 87

6.1.9 Firmware Upgrade ................................................................................................... 87

6.1.10 Reset ....................................................................................................................... 88

7. AC-12 0 0 UR AirLive USB Control Center ............................................. 89

7.1 Introduction AC-1200UR AirLive USB Control Center ............................................ 89

7.2 How to install the software ......................................................................................... 90

7.3 AirLive USB Control Center introduction .................................................................. 90

8. Frequent Asked Questions ................................................................... 93

9. Specifications ........................................................................................ 95

10. Wireless Network Glossary ................................................................ 98

AirLive AC-1200R User’s Manual

Introduction

1.1 Overview

1. Introduction

The AC-1200UR is a multi-functional dual band concurrent AP Router that can operate in 5 different wireless modes. The AP features 2 radios that run in 5GHz or 2.4GHz frequency band. Moreover, it supports latest standard 802.11ac which provide the higher throughout than pervious standard.

Feature Summary

• 2.4G/5G Dual Band Concurrent

• 11ac + 11b/g/n, data rate up to 1200Mbps

• 5 Wireless Modes

• 23dBm* Hi-Power with standard antennas. ( Limit 20dBm in EU)

• QoS and Bandwidth Control

• Multiple SSID and VLAN

• 10/20/40/80 Channel Width

• PPPoE Server

• Virtual Server and DMZ support

• Syslog Support

1 AirLive AC-1200UR User’s Manual

1. Introduction

Mode

Radio 1(5G)

Radio2(2.4G)

Applications

Dual Band Router

AP Router

Dual Home Networks: and 2.4GHz for PC

Dual AP Mode

Access Point

Dual Band Hotspots

WISP + AP

Client Mode

AP Router

Sharing WISP 5GHz Broadband Wirelessly

Bridge + AP

Bridge Mode

Access Point

WDS Wireless Repeater

Client + AP

Client

Access Point

Universal Repeater

1.2 Firmware Upgrade and Tech Support

If you encounter a technical issue that cannot be resolved by information on this guide, we recommend that you visit our compreh ensi ve website support at www.airlive.com. The tech support FAQ are frequently updated with latest information.

In addition, you might find new firmware that either increase software functions or provide bug fixes for AC-1200UR. You can reach our on-line support center at the following link:

http://www.airlive.com/support/support_3.php

1.3 Wireless Operation Modes

The AC-1200UR can perform as a multi-function wireless device. Through the AirLive web interface, users can easily select which wireless mode they wish the AC-1200UR to perform.

The AC-1200UR provides 5 modes of wireless operational applications. It can transform the AC-1200UR into different roles in the wireless infrastructure. Below is the example application table for AC-1200UR.

5GHz for Games/AV

1.3.1 Dual Band Router Mode

In Dual Band Concurrent mode, the radio1 works in 5GHz while radio2 works in 2.4GHz mode. That means the AC-1200UR can provide Internet service to both 5GHz (like game network) and 2.4GHz(like PC network) at the same time.

AirLive AC-1200UR User’s Manual

1. Introduction

3 AirLive AC-1200UR User’s Manual

1. Introduction

1.3.2 Dual AP Mode

In Dual AP mode, both wireless interface of AC-1200UR are set as AP and provide hotspot service on each interface. Radio1 is set to 11ac mode while Radio2 is set to 11g/b/nMode. This mode is most useful for Dual Band Hotspot function such as in the hotels, shopping malls, or offices.

AirLive AC-1200UR User’s Manual

1. Introduction

1.3.3 WISP + AP Mode

In this mode, Radio1 (5GHz) acts as a client to connect with remote WISP Base Station. Radio 2 (in 11g/b/n mode) works as an AP router to allow subscriber to share the WISP connection wirelessly. Using the AC-1200UR, WISP no longer requires 2 AP/CPE to provide wireless access in subscriber’s home or office.

5 AirLive AC-1200UR User’s Manual

1. Introduction

1.3.4 Bridge + AP Mode

In this mode, Radio1 is working as Bridge mode in 5GHz while Radio 2 is working as AP mode in 2.4GHz. This mode is us eful for WISP b ackbo ne a ppli catio n w here Ra dio 1 i s us ed for connection to anoth er Base Sta tion and R adio2 is use d for s erv ice to s ubsc riber s. This mode can also be used as repeater in indoor environment.

The AC-1200UR’s Bridge mode can be configured as “WDS Bridge”. In WDS Bridge, you must enter the remote AP’s MAC Address. It can connect with another AC-1200UR via WDS Bridge.

AirLive AC-1200UR User’s Manual

1.3.5 Client + AP Mode

1. Introduction

In this mode, it can work as a wireless repeater to extend the coverage of remote wireless router.

Radio 1 (5G) work i n the C l i ent M o de to receive the signal from another AP such as Air M ax 5x. Radio 2 (2.4) work in AP Mode to provide the connection for the NB or Smart Phone.

7 AirLive AC-1200UR User’s Manual

1. Introduction

AirLive AC-1200UR User’s Manual

2. Installing the AC-1200R

Installing the

AC-1200UR

This section describes the har dware features and the hardware installation procedur e for the AC-1200UR. For software configuration, please go to chapter 3 for more details.

2.1 Before You Start

It is important to read through this section before you install the AC-1200UR.

 The use of 5GHz spectrum might be prohibited in some countries. Please consult with

your country’s telecom regulation first.

 Please installation the antennas first before connecting the power. Connecting the

power without installing the antennas may result in damage to the wireless radios which may void your warranty.

2.2 Installing AC-1200UR

The AC-1200UR package contains the following items:

 One AC-1200UR main unit  One 12V 1A DC power adapter  Indoor detachable dual band Omni Anten na x 2  Quick Start Guide  User’s Guide CD

9 AirLive AC-1200UR User’s Manual

2.3 Knowing Your AC-1200UR

Solid Green LED while the device is powered on,

Solid Green LED while the device is powered on.

LAN ports status LED, Solid Green LED shows when a port is actively connected, blinking while

2.3.1. Front Side Introduction

2. Installing the AC-1200R

AirLive AC-1200UR User’s Manual

LED # Display Description

1 Power

either by power adaptor

2 2.4G

Blinking while there is Data transmission, dark when

3 5G

4~8 LAN

WAN

this interface is turn off.

there is data transmission, turns into dark when this disconnected. LAN5 is also the WAN port

2.3.2. Back Side Introduction

SMA connector. 2

A power supply adaptor delivered with

When it is in Dual Band Router

In Dual AP

USB connector to connect USB disk or USB

2. Installing the AC-1200R

Port # Display Description

1 WLAN1 Detachable antenna with R-

indoordual band antennas are delivered.

2 Power Adaptor 12V 1

product.

3 WPS/Reset It works as WPS or Reset button. Push 15 sec

of the button, the device will reset to default

4 WAN Port WAN Port.

mode, it function as a WAN port. mode , it work as LAN port

5~8 LAN LAN port

9 USB

printer

10 WLAN2 Detachable antenna with R-SMA connector.

11 AirLive AC-1200UR User’s Manual

2. Installing the AC-1200R

2.4 InstallationSteps

This section describes installationsteps required for the AC-1200UR before it can work properly in your network.

2.4.1. Installation Steps by using LAN port

1. Install antennas into the AC-1200UR

2. Connect the broadband line into the WAN port of the AC-1200UR

3. Connect your PC to any LAN port.

4. Connect the power jack to the power port.

5. Wait for 5 minutes. Then open the browser on your PC and type in "192.168.1.254" to reach the web management

6. For software configuration, please go to chapter 3 for more details.

AirLive AC-1200UR User’s Manual

2.4.2. Wirele s s Ins t all a t ion S t e ps

2. Installing the AC-1200R

1. Install antennas into the AC-1200UR

2. Connect the broadband line into the WAN port of the AC-1200UR

3. Connect the power jack to the power port.

4. Wait for 5 minutes. Then on your Notebook PC, scan and connect to “airlive” wireless network

5. Open your web browser and type “192.168.1.254” to configure your AC-1200UR

6. When prompt for username/password, type “admin” as username and “airlive” as password

7. When the following screen appears, click on “Setup” to configure wireless settings.

13 AirLive AC-1200UR User’s Manual

2. Installing the AC-1200R

8. Select “Change Settings for: Radio2”. Then click on “Security Settings”

AirLive AC-1200UR User’s Manual

2. Installing the AC-1200R

9. Choose WPA2-PSK and enter your own encryption key (please write down and do not forget it is case sensitive). Then click on “Apply” button

10. The AC-1200UR will reboot. After about 3 minutes, please try to access the network again. You will be prompted to enter your encryption key.

15 AirLive AC-1200UR User’s Manual

2. Installing the AC-1200R

2.4.3. Inter ne t I ns t all ation Steps

Please finish the LAN port and Wireless installations fir st in 2.4 .1 an d 2.4. 2 be for e performing the following steps.

If you are using AC-1200UR as a router, please follow the steps below:

1. Please make sure the Internet line is connected to the WAN port.

2. Open your web browser and type 192.168.1.254

3. When prompt for password, enter “admin” for username and “airlive” for password.

4. Choose “Dual Band Router” on Operation Mode Screen and click on “Setup”

5. Choose “WAN Port Settings” on the bottom.

AirLive AC-1200UR User’s Manual

2. Installing the AC-1200R

6. Please enter your ISP’s authentication Information and Click on “Apply” button. Here are some guidelines.

 If your Internet connection is ADSL, it is most likely using the following option:

Your I SP already provides you with PPPoE authentication information, select this button and enter the information below:

 If your internet connection is Cable Modem, it is most likely to use the option:

If your ISP already provides you with a Host Name, select this button and enter the information below: (DHCP)

However, please still consult with your ISP about the correct account information.

7. Click on “Apply” to finish.

17 AirLive AC-1200UR User’s Manual

3. Configuring the AC-1200R

Configuring the

AC-1200UR

The AC-1200UR offers web based management interface. You can configure through standard web browser (http). In this chapter, we will explain AC-1200UR’s available management interfaces and how to get into them. Then, we will provide the introduction on Web Management and recommended initial settings.

3.1 Important Information

The following information will help you to get start quickly.However, we recommend you to read through the entire manual before you start. Please note the password and SSID are case sensitive.

 The default IP address is: 192.168.1.254 Subnet Mask: 255.255.255.0  When using Web UI, the login as follow:

 User name: admin

 Password: airlive  The default radio mode for Radio 1 is 802.11ac/n  The default radio mode for Radio 2 is 802.11g/b/n  The default SSID for Radio 1 is: airlive 5g  The default SSID for Radio 2 is:airlive  The default wireless mode is : Dual Band Router Mode  After power on, please wait for 2 minutes for AC-1200UR to finish boot up  Please remember to click on “Apply” for new settings to take effect

AirLive AC-1200UR User’s Manual

3. Configuring the AC-1200R

3.2 Prepare Your PC

The AC-1200UR can be managed remotely by a PC through either the wired or wireless network. The default IP address of the AC-1200UR is 192.168.1.254 with a subnet mask of

255.255.255.0. This m eans the IP addres s of the PC shoul d be in the range of 192.168.1.1 to 192.168.1.253.

The default mode for AC-1200UR is “Dual Band Router” mode. In this mode, the AC-1200UR’s DHCP server is turned on; therefore, your PC can get IP automatically from AC-1200UR.You just need to set your PC to “Obtain IP address automatically” on the TCP/IP setting. By default, Windows already do this so you do not need to change.

However, if you are using AC-1200UR in non-router modes (Dual AP, Dual Band Router, WDS+AP, Client+AP), you need to set your IP manually. To prepare your PC for management with the AC-1200UR, please do the foll owing:

1. Connect your PC directly to the LAN port of AC-1200UR

2. Set your PC’s IP address manually to 192.168.1.100 (or other address in the same

subnet)

You are ready now to configure the AC-1200UR using your PC.

19 AirLive AC-1200UR User’s Manual

3. Configuring the AC-1200R

3.3 Management Interface

The AC-1200UR can be configured using web management interfaces below:

3.3.1 Web Management (HTTP):

You can manage y our AC-1200UR by simply typing its IP address in the web brow ser. Most functions of AC-1200UR can be accessed by web management interface. We recommend using this interface for initial configurati o ns . To begin, simply enter AC-1200UR’s IP address (default is 192.168.1.254) on the web browser. The default user name is “admin”; default password is “airlive”.

3.4 Introduction to Web Management

3.4.1 Getting into Web Management

Normal Web Management (HTTP)

To get into the Normal Web Management, simply type in the AC-1200UR’s IP address (default IP is 192.168.1.254) into the web browser’s address field.

3.4.2 Login

After the procedure above, the Login username and password is required.

Please type in the username and password. The default username is “admin” and password is “airlive”. After thatOperation Mode page will appear.

AirLive AC-1200UR User’s Manual

3. Configuring the AC-1200R

Wizard to setup Dual Click to configure wireless settings

3.5 Initial Configuration

We recommend users to brows e thro ug h AC-1200UR’s web management interface to get an overall picture of the functions and interface. Below are the recommended initial configurations for firs t ti me log in:

3.5.1 Choose the wireless Operation Modes

The wireless settings of AC-1200UR ar e dep e ndent on the wireless operation mode you choose. Therefore, the first step is to choose the operation mode. For explanation on when to use what operation mode, please refer to Chapter 1.

Band Router Mode

Follow the example below to change to “WISP + AP” mode

1. Select “WISP + AP” mode

2. Click on “setup” button

3. The AP will reboot, wait for about one minute

21 AirLive AC-1200UR User’s Manual

3. Configuring the AC-1200R

3.5.2 Change the Device’s IP Address

The defaul t IP address is at 192.168.1.254. You should change it to the same subnet as your network. Also, if you want to manage AC-1200UR remotely, you have to set the Gateway and DNS server information.

To setup the IP settings for AC-1200UR, please select “General Setup” ->LAN”. After entering the IP information, click on “Apply” to finish.

AirLive AC-1200UR User’s Manual

3. Configuring the AC-1200R

3.5.3 Change the Country Code

The legal frequency and channels in 5GHz spectrum varies between countries. The default country code i s ETSI which should requi r e no changes If y ou ar e l iving in Europe. If you are living outside EU, you should change the country code accordingly. In the example below, we will change the country code to FCC

Step 1. Select “Operation Mode” -> “Setup”

Step 2. From the Regulatory Domain, please select your regulatory domain (FCC or

ETSI) and click on “Apply” to finish.

23 AirLive AC-1200UR User’s Manual

+ 92 hidden pages