Congratulations on your purchase of the Golden 150 Wireless Mini USB Adapter! Its high
bandwidth combined with great wireless coverage delivers fast and reliable connection for
all of your networking applications. The adapter will yield a higher throughput especially
when it is used with AR570W Airlink101® Wireless 150 Router.
A full range of security features WEP, WPA-PSK, and WPA2-PSK provide you the highest
level of wireless network security. The bundled wireless utility Airlink101 Wireless Monitor
allows you to set up the adapter with an easy-to-use user interface. The Golden 150
Wireless USB Adapter works with 802.11 b/g/n network devices to ensure compatibility
with your existing wireless products.
1.1 Package Contents
Before you begin the installation, please check the items of your package. The package
should include the following items:
• Golden 150 Wireless Mini USB Adapter
• Quick Installation Guide
• Installation CD (Driver/Utility/Manual)
1.2 Features
• Highest wireless data rate of up to 150Mbps*, 3 times faster than 802.11g
• WPA2-PSK, WPA-PSK enhanced security to provide a full protection for your
wireless connection
• Reliable and stable wireless connection with great coverage
• Easy Setup Button for easy connection to the existing wireless network
• Great for environments that need high wireless data traffic
• Fully compatible with 802.11b/g/n
• RoHS compliant
2
2. Install Wireless USB Adapter
This section provides instructions on how to install the Golden 150 Wireless Mini USB
Adapter. The driver is installed along with the utility.
Step 2.1 Insert the USB adapter into an available USB port of your computer.
Step 2.2Click Cancel when you see the Found New Hardware Wizard.
Windows XP/2000 Users:
Windows Vista Users:
3
Step 2.3 Insert the Installation CD in the CD drive. The Autorun screen will pop up. Select
Install Utility and Driver from the menu.
4
Note: If the Autorun screen doesn’t appear automatically go to Start, Run, and
type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK.
Windows Vista Users:When you get warning message(s), make sure that you give
permission to continue with the installation of the driver software.
Step 2.4The Airlink101 WLAN Monitor screen will popup. Click Next at the screen.
Step 2.5 Click Install to begin the installation.
5
Step 2.6 For Windows XP, click on Continue Anyway.
For Windows Vista: click on Install this driver software anyway.
6
Please wait when Windows is installing the driver for Airlink101 Wireless Adapter and the
utility, Airlink101 Wireless Monitor.
Step 2.7 Click Finish to complete the installation.
7
Step 2.8 Select Yes, I want to restart my computer now. Click Finish to complete the
installation.
The driver and utility have been installed. Please continue to the next section.
8
3. Connect to Wireless Network
This section describes how to connect your wireless USB adapter to a wireless network.
Step 3.1 Open the Airlink101 Wireless Monitor utility by double clicking on the Airlink101
Wireless Monitor Utility icon in the system tray at the bottom right-hand corner of your
screen.
Step 3.2
The Easy Setup Button (Wi-Fi Protected Setup) is a new and easy way to configure the
encryption for your wireless network clients. In order to use it, you need to have a router
that supports this feature. If your router doesn’t support Easy Setup Button function (Wi-Fi
Protected Setup), continue to Step 3.3.
9
1. Push the Easy Setup Button of the Adapter until you see the following window pops
up on the monitor.
This window pops up to acknowledge you the Adapter is starting to establish a
connection.
2. Within the following 2 minutes, push the Easy Setup Button (i.e. WPS Button) on the
back of the Router and release it right away. The picture below shows Airlink101
AR570W Wireless 150 Router.
10
3. The router will now start the handshake with the wireless USB adapter. The
connection will be established in few seconds. Continue to Step 3.5.
If the connection is not able to establish, continue to Step 3.3.
Step 3.3 Click the Available Network tab of the Wireless Monitor, select the wireless
network that you wish to connect to, and click Add to Profile.
If the network that you are attempting to connect does not have encryption enabled, you
will receive a warning about connecting to an unsecured network. Click OK to complete
the connection. Go to Step 3.5.
Step 3.4 Enter the wireless security key into the Network Key, Confirm Network Key
boxes and click OK.
The Adapter will automatically detect the type of Network Authentication and the Data
encryption. It is suggested that you leave these settings unchanged.
11
Step 3.5 The connection should be now established. Go to General tab to check the
status of the connection. Verify that IP Address, Subnet Mask and Gateway have valid
numbers assigned to them (instead of all 0’s). The Status should be Associated, and
there will be green bars next to Signal Strength and Link Quality.
12
13
4. Wireless Monitor
This section describes the various functions of the Wireless Monitor that you can
configure, including the settings of wireless encryption.
4.1 General
The General tab provides you with the status of the current connection, including signal,
network name (SSID) and IP Address.
At the bottom, you have options for controlling the utility and adapter:
Show Tray Icon: Check this box to show or hide the utility icon on the task bar.
14
Loading...
+ 35 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.