Airlink101 ASW324V2 User Manual

Download

Page 1

Quick Installation Guide

24-Port 10/100Mbps

Green Switch

Model# ASW324v2

Ver. 1A

Page 2

Trademarks

No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Phoebe Micro, Inc.

Preface

FCC Warning

This device has been tested and found to comply with limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the user’s manual, may cause interference in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Page 3

Introduction

Congratulations on your purchase of the 24-Port 10/100Mbps Green Switch! It is an easy-to-install network switch which helps you to extend your network structure quickly and reliably. The 24-Port 10/100Mbps Green Switch is designed for energy saving, easy installation and high performance in an environment where network traffic and the number of users increase continuously. You can add other Ethernet devices like computers, IP cameras, and Network Attached Storage (NAS) onto your network quickly and easily. The Green EEE (Energy Efficient Ethernet) technology of ASW324v2 automatically reduces the power consumption when any connected port is detected inactive (idle or cable-unplugged) and it intelligently allocates less power to any port that connects with an Ethernet cable shorter than 20m (66 ft)*.

Before you start installation, please check the package contents:

Package Contents:

• 24-Port 10/100Mbps Green Switch

• Power Cord

• Quick Installation Guide

• Brackets and Screws

Page 4

Section 1

Hardware Description

1.1 Hardware Interface

• 24 x Port 10/100Mbps auto-negotiation RJ45 port

• All ports support auto MDI/MDIX, no need to use

cross-over cables

1.2 Panel

1.2.1 Front Panel

The front panel of the Switch consists of LED indicators, and 24 10/100Mbps ports. The figure below shows the front panel of the Switch.

Figure 1-1 Front Panel View of the Switch

• 10/100Mbps Ports (Port 1~24): These ports support 10/100Mbps, and can operate in Half/Full Duplex transfer modes. These ports also support automatic MDI/MDI-X crossover detection, offering true “plug and play” function.

• LED Indicators: Comprehensive LED indicators display the status of the Switch and the network (see Section

1.2.3).

Page 5

1.2.2 Rear Panel

Figure 1-2 Rear Panel View of the Switch

• AC Power Connector: Supports AC 100~240V, 50~60Hz.

NOTE:

Do not cover or put anything on or surrounding the Switch while the Switch is operating.

1.2.3 LED indicators information

The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed.

Figure 1-3 Front Panel View of the Switch

Page 6

• POWER: Power Indicator

Status

LED Color

Solid Blinking Off

The Switch is

POWER Green

power-on

• Port 1~24 10/100Mbps Status LEDs

Status

LED Color

Solid Blinking Off

N/A No power

LINK/

ACT

LED Color

10/ 100M Green

Green

No activities

on the

10/100Mbps

Ethernet

network

Solid Blinking Off

The

respective

port is

connected to

the

10/100Mbps

Ethernet

network

The port is transmitting or receiving

data at

10/100Mbps

Status

N/A

No link

The

respective

port is

connected

to the slow

Ethernet

network

Page 7

Section 2

Installing the Switch

The site where you place the Switch may greatly affect its performance.

2.1 Installation

Please follow the guidelines below to install the Switch:

• Please install the Switch in a fairly cool and dry place. Please refer to the Technical Specifications for the acceptable temperature and humidity operating ranges.

• Please install the Switch on a sturdy, level surface that can support its weight.

• When connecting the power cord to the Switch and the power outlet, the distance should be no more than 182cm.

• Please leave at least 10cm (about 4 inches) of space at the front and rear of the Switch for ventilation.

2.2 Desktop or Shelf Installation

When installing the Switch on the desktop or shelf, please attach the rubber feet to the Switch. Peel off the protective paper on the pads and attach them to the bottom of the Switch (one at each corner).

Page 8

2.3 Rack Installation

The Switch is rack-mountable and can be installed on an EIA 11-inch equipment rack. To do this, first install the mounting brackets on the Switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the Switch.

2.4 Power on the Switch

The Switch has a universal power supply ranging from 100V to 240V AC, 50 ~ 60Hz power source. The AC power connector is located at the rear of the unit. The Switch’s power supply will adjust to the local power source automatically.

Page 9

Section 3

Connecting the Switch

This section describes how to connect the Switch to your 10/100Mbps Ethernet network.

Your network device (i.e. computer, switch, IP Camera, VoIP) can be connected to any port of the Switch via a two-pair UTP Category 5 Cable. If the LED indicators do not light up after making a proper connection, check your network device, the cable, the Switch conditions and connections.

Page 10

Section 4

Troubleshooting

1. Power LED is not on

• Check if the power adapter is properly connected to the power outlet. Make sure the power jack is firmly plugged into the power socket of the switch.

2. Link/Activity is not lit when connect to 10/100Mbps device

• Made sure that the network device attached to the switch is turned ON.

• Check the network cable; make sure it is properly connected to the switch and the network device.

• Check the network cable; make sure the Ethernet cables comply with the specifications described in Section 2.

Page 11

Section 5

Technical Specifications

Standards

• IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX, IEEE

802.3x Flow Control and IEEE 802.3az(EEE – Energy Efficient Ethernet)

Network Cables

• Ethernet (10Base-T): Cables: 2-pair UTP Cat. 3, 4, 5, Twisted Pair (UTP). Up to 100m

• Fast Ethernet (100Base-T): 2-pair UTP Cat. 5, Twisted Pair (UTP). Up to 100m

Ports

• 24 x 10/100Mbps Auto-Negotiation RJ45 Port

Access Method

• CSMA/CD

Transmission Method

• Store and Forward

Data Transfer Rate**

• Ethernet: 10/20Mbps – Half/Full-Duplex

• Fast Ethernet: 100/200Mbps – Half/Full Duplex

LED

• Power: Green

• Link/Activity: Link/Activity (Green)

10/100M (Green)

Rack Mount

• 11-Inch Rack-Mountable with mounting kits

Dimensions

Page 12

• 280mm x 165mm x 45mm (LxWxH)

Weight

• 1400g (3 lb)

Physical and Environmental

• Power Input: 100~240V AC, 50~60Hz

• Operation Temperature: 0 °C ~ 40°C(32°F ~ 104°F)

• Storage Temperature: -20°C ~ 70°C(-4°F ~ 158°F)

• Humidity: 5% ~ 90% RH, non-condensing

Certification

• FCC, CE

Page 13

Section 6

Technical Support

E-mail: support@airlink101.com

Toll-Free: 1-888-746-3238*

Web Site: www.airlink101.com

* Free Voice Technical Support is only available within the hardware warranty (1-Year Limited Warranty from the date of purchase). Customer is required to provide invoice as purchase evidence.

**Network conditions and environmental factors as well as network overhead can lower actual data throughput rate.

AirLink101 that are identified as trademarks and/or service marks are, unless noted

® logo, specific product designations, and all other words and logos

otherwise, the trademarks and service marks of AirLink101 service names are the property of their respective holders. AirLink101 products are protected under numerous U.S. and foreign patents and pending applications, mask work rights, and copyrights.

®. All other product or