Aiphone ja-2sd User Manual

JA-2SD
HANDSFREE SUB MASTER STATION HANDSFREE SUB MASTER STATION HANDSFREE SUB MASTER STATION HANDSFREE SUB MASTER STATION HANDSFREE SUB MASTER STATION
A
INSTALLATION & OPERATION MANUAL
MANUEL D’INSTALLATION ET D’UTILISATION
EINBAU- & BEDIENUNGSANLEITUNG
MANUAL DE INSTALACION Y OPERACION
INSTALLATIE- EN BEDIENINGSHANDLEIDING
- 1 -
General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water General Precautions
WARNING
(Negligence could result in death or serious injury to people)
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Do not connect any power source other than specified to terminals +, - nor install 2 power supplies in parallel to single input. Fire or unit damage could result.
3. Keep the unit away from water or any other liquid. Fire or electric shock could result.
4. Do not put any metal into the unit through the openings. Fire or electric shock could result.
CAUTION
(Negligence could result in injury to people or damage to property)
1. Before turning on the power, make sure wires are not crossed or shorted. Fire or electric shock could result.
2. When mounting the unit on wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result.
3. While the power supply is turned on, do not make any wiring connections.Electric shock or unit trouble could result.
4. Do not install the unit in any of the following locations.Fire, electric shock,or unit trouble could result.
* Places under direct sunlight, or near heating equipment that varies in
temperature.
* Places subject to dust, oil, chemicals, * Places subject to moisture and humidity extremes, such as bathroom,cellar,
greenhouse, etc.
* Places where the temperature is quite low, such as inside a refrigerated areaor
in front of air-conditioner.
GENERAL PRECAUTIONS
1. This unit is for indoor use only. Do not use outdoors.
2. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference.
3. If a cellular phone is used close by, the unit may malfunction.
4. Keep the unit more than 1 m away from radio or TV sets.
5. If the monitor station is operated near office equipment, radios or TVs, it will be affected by radio wave interference or noise. Carefully select the place of use.
6. Ambient noise around the unit may prevent normal communication. This is not unit trouble.
Mesures générales d'interdiction Interdiction de démonter
l'appareil La platine de rue vidéo est prévue pour un montage extérieur, toutefois il ne faut pas l’arroser au moyen de système haute
pression. Précautions générales
AVERTISSEMENT
(Le non-respect de cet avertissement risque d'entraîner des
blessures graves, voire mortelles)
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Do not connect any power source other than specified to terminals +, - nor install 2 power supplies in parallel to single input. Fire or unit damage could result.
3. Keep the unit away from water or any other liquid. Fire or electric shock could result.
4. Do not put any metal into the unit through the openings. Fire or electric shock could result.
ATTENTION
(Le non-respect de cet avertissement risque d'entraîner des
blessures ou des dégâts matériels)
1. Before turning on the power, make sure wires are not crossed or shorted. Fire or electric shock could result.
2. When mounting the unit on wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result.
3. While the power supply is turned on, do not make any wiring connections.Electric shock or unit trouble could result.
4. Do not install the unit in any of the following locations.Fire, electric shock,or unit trouble could result.
* Places under direct sunlight, or near heating equipment that varies in
temperature.
* Places subject to dust, oil, chemicals, * Places subject to moisture and humidity extremes, such as bathroom,cellar,
greenhouse, etc.
* Places where the temperature is quite low, such as inside a refrigerated areaor
in front of air-conditioner.
PRECAUTIONS GENERALES
1. This unit is for indoor use only. Do not use outdoors.
2. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference.
3. If a cellular phone is used close by, the unit may malfunction.
4. Keep the unit more than 1 m away from radio or TV sets.
5. If the monitor station is operated near office equipment, radios or TVs, it will be affected by radio wave interference or noise. Carefully select the place of use.
6. Ambient noise around the unit may prevent normal communication. This is not unit trouble.
Allgemeine Verbote Zerlegungsverbote Verbote zum
Schutz der Anlage vor Wasser Allgemeine Vorsichtsmaßnahmen
WARNUNG
(Eine Nichtbeachtung kann zu schweren oder tödlichen
Verletzungen führen)
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Do not connect any power source other than specified to terminals +, - nor install 2 power supplies in parallel to single input. Fire or unit damage could result.
3. Keep the unit away from water or any other liquid. Fire or electric shock could result.
4. Do not put any metal into the unit through the openings. Fire or electric shock could result.
VORSICHT
(Eine Nichtbeachtung kann zu Verletzungen und zu
Sachbeschädigungen führen)
1. Before turning on the power, make sure wires are not crossed or shorted. Fire or electric shock could result.
2. When mounting the unit on wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result.
3. While the power supply is turned on, do not make any wiring connections.Electric shock or unit trouble could result.
4. Do not install the unit in any of the following locations.Fire, electric shock,or unit trouble could result.
* Places under direct sunlight, or near heating equipment that varies in
temperature.
* Places subject to dust, oil, chemicals, * Places subject to moisture and humidity extremes, such as bathroom,cellar,
greenhouse, etc.
* Places where the temperature is quite low, such as inside a refrigerated areaor
in front of air-conditioner.
ALLGEMEINE VORSICHTSMASSNAHMEN
1. This unit is for indoor use only. Do not use outdoors.
2. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference.
3. If a cellular phone is used close by, the unit may malfunction.
4. Keep the unit more than 1 m away from radio or TV sets.
5. If the monitor station is operated near office equipment, radios or TVs, it will be affected by radio wave interference or noise. Carefully select the place of use.
6. Ambient noise around the unit may prevent normal communication. This is not unit trouble.
Prohibiciones generales Prohibición de desmontar la unidad Prohibición de exponer al agua la unidad Precauciones
generales
ADVERTENCIA
(No seguir estas instrucciones podría provocar daños graves o
incluso mortales)
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Do not connect any power source other than specified to terminals +, - nor install 2 power supplies in parallel to single input. Fire or unit damage could result.
3. Keep the unit away from water or any other liquid. Fire or electric shock could result.
4. Do not put any metal into the unit through the openings. Fire or electric shock could result.
- 2 -
PRECAUCION
(No seguir estas instrucciones podría causar daños físicos o
materiales)
1. Before turning on the power, make sure wires are not crossed or shorted. Fire or electric shock could result.
2. When mounting the unit on wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result.
3. While the power supply is turned on, do not make any wiring connections.Electric shock or unit trouble could result.
4. Do not install the unit in any of the following locations.Fire, electric shock,or unit trouble could result.
* Places under direct sunlight, or near heating equipment that varies in
temperature.
* Places subject to dust, oil, chemicals, * Places subject to moisture and humidity extremes, such as bathroom,cellar,
greenhouse, etc.
* Places where the temperature is quite low, such as inside a refrigerated areaor
in front of air-conditioner.
INSTALLATION INSTALLATION EINBAU INSTALACIÓN INSTALLATIE
1-1
1. This unit is for indoor use only. Do not use outdoors.
PRECAUCIONES GENERALES
2. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference.
3. If a cellular phone is used close by, the unit may malfunction.
4. Keep the unit more than 1 m away from radio or TV sets.
5. If the monitor station is operated near office equipment, radios or TVs, it will be affected by radio wave interference or noise. Carefully select the place of use.
6. Ambient noise around the unit may prevent normal communication. This is not unit trouble.
Algemeen verbod Verbod het toestel te demonteren Verbod het toestel in contact te brengen met water Algemene
voorzorg
WAARSCHUWING
(niet-naleving kan de dood of ernstige verwonding van mensen
veroorzaken)
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Do not connect any power source other than specified to terminals +, - nor install 2 power supplies in parallel to single input. Fire or unit damage could result.
3. Keep the unit away from water or any other liquid. Fire or electric shock could result.
4. Do not put any metal into the unit through the openings. Fire or electric shock could result.
OPGELET
(niet-naleving kan verwondingen van mensen of beschadigingen
van eigendommen veroorzaken)
1. Before turning on the power, make sure wires are not crossed or shorted. Fire or electric shock could result.
2. When mounting the unit on wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result.
3. While the power supply is turned on, do not make any wiring connections.Electric shock or unit trouble could result.
4. Do not install the unit in any of the following locations.Fire, electric shock,or unit trouble could result.
* Places under direct sunlight, or near heating equipment that varies in
temperature.
* Places subject to dust, oil, chemicals, * Places subject to moisture and humidity extremes, such as bathroom,cellar,
greenhouse, etc.
* Places where the temperature is quite low, such as inside a refrigerated areaor
in front of air-conditioner.
ALGEMENE VOORZORGSMAATREGELEN
1. This unit is for indoor use only. Do not use outdoors.
2. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference.
3. If a cellular phone is used close by, the unit may malfunction.
4. Keep the unit more than 1 m away from radio or TV sets.
5. If the monitor station is operated near office equipment, radios or TVs, it will be affected by radio wave interference or noise. Carefully select the place of use.
6. Ambient noise around the unit may prevent normal communication. This is not unit trouble.
WIRING
English
Wiring method
Wire the inside stations in a station-to-station manner.
Cable
1. Parallel cable or single-sheathed cable are recommended. Vinyl jacket, PE(polyethylene) insulation cable is recommended.
2. Never use loose wires, twisted pair cable or coaxial cable.
3. When using existing wires, which may contain unused wires, it is suggested to terminate both ends of unused pair(s) with a 120 resistor.
WIRING
Français
Wiring method
Wire the inside stations in a station-to-station manner.
Cable
1. Parallel cable or single-sheathed cable are recommended. Vinyl jacket, PE(polyethylene) insulation cable is recommended.
2. Never use loose wires, twisted pair cable or coaxial cable.
3. When using existing wires, which may contain unused wires, it is suggested to terminate both ends of unused pair(s) with a 120 resistor.
- 3 -
WIRING
Wiring method
Wire the inside stations in a station-to-station manner.
Cable
1. Parallel cable or single-sheathed cable are recommended. Vinyl jacket, PE(polyethylene) insulation cable is recommended.
2. Never use loose wires, twisted pair cable or coaxial cable.
3. When using existing wires, which may contain unused wires, it is suggested to terminate both ends of unused pair(s) with a 120 resistor.
WIRING
Wiring method
Wire the inside stations in a station-to-station manner.
Cable
1. Parallel cable or single-sheathed cable are recommended. Vinyl jacket, PE(polyethylene) insulation cable is recommended.
2. Never use loose wires, twisted pair cable or coaxial cable.
3. When using existing wires, which may contain unused wires, it is suggested to terminate both ends of unused pair(s) with a 120 resistor.
WIRING
Wiring method
Wire the inside stations in a station-to-station manner.
Cable
1. Parallel cable or single-sheathed cable are recommended. Vinyl jacket, PE(polyethylene) insulation cable is recommended.
2. Never use loose wires, twisted pair cable or coaxial cable.
3. When using existing wires, which may contain unused wires, it is suggested to terminate both ends of unused pair(s) with a 120 resistor.
Deutsch
Español
Nederlands
1-2
Wiring distance Wiring distance Wiring Wiring distance Wiring distance
NAMES NOMES BEZEICHNUNGEN NOMBRES BENAMINGEN
NAMES & FUNCTIONS
[1] Speaker [2] Door call-in LED (Door 1) [3] Door call-in LED (Door 2) [4] Room CALL button [5] DOOR RELEASE button [6] Mic. [7] TALK button [8] Transmit LED [9] Door call-in selector: 1, 2 or 1&2 [10] Chime TONE volume control
NAMES & FUNCTIONS
[1] Speaker [2] Door call-in LED (Door 1) [3] Door call-in LED (Door 2) [4] Room CALL button [5] DOOR RELEASE button [6] Mic. [7] TALK button [8] Transmit LED [9] Door call-in selector: 1, 2 or 1&2 [10] Chime TONE volume control
English
Français
- 4 -
NAMES & FUNCTIONS
[1] Speaker [2] Door call-in LED (Door 1) [3] Door call-in LED (Door 2) [4] Room CALL button [5] DOOR RELEASE button [6] Mic. [7] TALK button [8] Transmit LED [9] Door call-in selector: 1, 2 or 1&2 [10] Chime TONE volume control
NAMES & FUNCTIONS
[1] Speaker [2] Door call-in LED (Door 1) [3] Door call-in LED (Door 2) [4] Room CALL button [5] DOOR RELEASE button [6] Mic. [7] TALK button [8] Transmit LED [9] Door call-in selector: 1, 2 or 1&2 [10] Chime TONE volume control
NAMES & FUNCTIONS
[1] Speaker [2] Door call-in LED (Door 1) [3] Door call-in LED (Door 2) [4] Room CALL button [5] DOOR RELEASE button [6] Mic. [7] TALK button [8] Transmit LED [9] Door call-in selector: 1, 2 or 1&2 [10] Chime TONE volume control
Deutsch
Español
Nederlands
MOUNTING MONTAGE MONTAGE MONTAJE MONTAGE
3-1
PACKAGE CONTENTS
1. JA-2SD
2. Wall mounting bracket
3. Packet of screws
4. INSTALLATION & OPERATION MANUAL
PACKAGE CONTENTS
1. JA-2SD
2. Wall mounting bracket
3. Packet of screws
4. INSTALLATION & OPERATION MANUAL
PACKAGE CONTENTS
1. JA-2SD
2. Wall mounting bracket
3. Packet of screws
4. INSTALLATION & OPERATION MANUAL
PACKAGE CONTENTS
1. JA-2SD
2. Wall mounting bracket
3. Packet of screws
4. INSTALLATION & OPERATION MANUAL
PACKAGE CONTENTS
1. JA-2SD
2. Wall mounting bracket
3. Packet of screws
4. INSTALLATION & OPERATION MANUAL
English
Français
Deutsch
Español
Nederlands
- 5 -
3-2
WIRING CABLAGE VERDRAHTUNG ALAMBRADO AANSLUITING
MOUNTING
1. Push RELEASE button (to unlock or to insert the wire securely).
2. Insert the cable into terminal.
[1] Screw (x2) [2] Wall mounting bracket [3] Single-gang box
MOUNTING
1. Push RELEASE button (to unlock or to insert the wire securely).
2. Insert the cable into terminal.
[1] Screw (x2) [2] Wall mounting bracket [3] Single-gang box
MOUNTING
1. Push RELEASE button (to unlock or to insert the wire securely).
2. Insert the cable into terminal.
[1] Screw (x2) [2] Wall mounting bracket [3] Single-gang box
MOUNTING
1. Push RELEASE button (to unlock or to insert the wire securely).
2. Insert the cable into terminal.
[1] Screw (x2) [2] Wall mounting bracket [3] Single-gang box
MOUNTING
1. Push RELEASE button (to unlock or to insert the wire securely).
2. Insert the cable into terminal.
[1] Screw (x2) [2] Wall mounting bracket [3] Single-gang box
English
Français
Deutsch
Español
Nederlands
WIRING
Impedance matching switch
Terminate farthest sub station, putting SW. to ON position, otherwise both image and audio are deteriorated.
WIRING
Impedance matching switch
Terminate farthest sub station, putting SW. to ON position, otherwise both image and audio are deteriorated.
WIRING
Impedance matching switch
Terminate farthest sub station, putting SW. to ON position, otherwise both image and audio are deteriorated.
WIRING
Impedance matching switch
Terminate farthest sub station, putting SW. to ON position, otherwise both image and audio are deteriorated.
WIRING
Impedance matching switch
Terminate farthest sub station, putting SW. to ON position, otherwise both image and audio are deteriorated.
English
Français
Deutsch
Español
Nederlands
- 6 -
5-1
OPERATIONS OPÉRATION BEDIENUNG OPERACIÓNES BEDIENING
Answering a door call (AUTO mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1, or DOOR 2.
3. Press for a moment TALK button and reply handsfree.
4. Press once TALK button at the end.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Answering a door call (AUTO mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1, or DOOR 2.
3. Press for a moment TALK button and reply handsfree.
4. Press once TALK button at the end.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Español
Nederlands
5-2
Answering a door call (AUTO mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1, or DOOR 2.
3. Press for a moment TALK button and reply handsfree.
4. Press once TALK button at the end.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Answering a door call (AUTO mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1, or DOOR 2.
3. Press for a moment TALK button and reply handsfree.
4. Press once TALK button at the end.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Answering a door call (AUTO mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1, or DOOR 2.
3. Press for a moment TALK button and reply handsfree.
4. Press once TALK button at the end.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
English
Français
Deutsch
Answering a door call (MANUAL mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
3. Depress and hold down TALK button for 1 sec. or more.
4. To transmit, talk while pressing TALK button, and to listen, release TALK button.
5. At the end, press once TALK button.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
- 7 -
English
Answering a door call (MANUAL mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
3. Depress and hold down TALK button for 1 sec. or more.
4. To transmit, talk while pressing TALK button, and to listen, release TALK button.
5. At the end, press once TALK button.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Answering a door call (MANUAL mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
3. Depress and hold down TALK button for 1 sec. or more.
4. To transmit, talk while pressing TALK button, and to listen, release TALK button.
5. At the end, press once TALK button.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Answering a door call (MANUAL mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
3. Depress and hold down TALK button for 1 sec. or more.
4. To transmit, talk while pressing TALK button, and to listen, release TALK button.
5. At the end, press once TALK button.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Answering a door call (MANUAL mode)
1. Momentarily depress CALL button.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
3. Depress and hold down TALK button for 1 sec. or more.
4. To transmit, talk while pressing TALK button, and to listen, release TALK button.
5. At the end, press once TALK button.
NOTES: Call-in timer; 45 sec. (approx.)
Communication timer; 1 min. (approx.) Press TALK button to manually turn on again (within 30 sec. after communication).
Français
Deutsch
Español
Nederlands
5-3
Instant voice calling
1. Momentarily depress CALL button. And, speak to inside station.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
NOTES: JA-D does not have this function.
Instant voice calling
1. Momentarily depress CALL button. And, speak to inside station.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
NOTES: JA-D does not have this function.
Instant voice calling
1. Momentarily depress CALL button. And, speak to inside station.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
NOTES: JA-D does not have this function.
Instant voice calling
1. Momentarily depress CALL button. And, speak to inside station.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
NOTES: JA-D does not have this function.
Instant voice calling
1. Momentarily depress CALL button. And, speak to inside station.
2. Chime tone sounds and caller’s voice is heard. Door call-in LED is lit for DOOR 1 or DOOR 2.
NOTES: JA-D does not have this function.
5-4
Activating Door Release
1. Depress and hold down DOOR RELEASE button.
2. The door is unlocked.
NOTES: Not available in standby mode.
Activating Door Release
1. Depress and hold down DOOR RELEASE button.
2. The door is unlocked.
NOTES: Not available in standby mode.
Activating Door Release
1. Depress and hold down DOOR RELEASE button.
2. The door is unlocked.
NOTES: Not available in standby mode.
Activating Door Release
1. Depress and hold down DOOR RELEASE button.
2. The door is unlocked.
NOTES: Not available in standby mode.
- 8 -
English
Français
Deutsch
Español
Nederlands
English
Français
Deutsch
Español
Activating Door Release
1. Depress and hold down DOOR RELEASE button.
2. The door is unlocked. NOTES: Not available in standby mode.
5-5
Nederlands
5-6
Room-to-room communication
1. Press CALL button once. Call verbally the rest station(s).
2. The called station(s) sounds a pretone and voice.
3. To answer, press TALK button once, and reply handsfree.
4. At the end, press TALK button. NOTES: Communication is approx. 1 min.-timed.
Room-to-room communication
1. Press CALL button once. Call verbally the rest station(s).
2. The called station(s) sounds a pretone and voice.
3. To answer, press TALK button once, and reply handsfree.
4. At the end, press TALK button. NOTES: Communication is approx. 1 min.-timed.
Room-to-room communication
1. Press CALL button once. Call verbally the rest station(s).
2. The called station(s) sounds a pretone and voice.
3. To answer, press TALK button once, and reply handsfree.
4. At the end, press TALK button. NOTES: Communication is approx. 1 min.-timed.
Room-to-room communication
1. Press CALL button once. Call verbally the rest station(s).
2. The called station(s) sounds a pretone and voice.
3. To answer, press TALK button once, and reply handsfree.
4. At the end, press TALK button. NOTES: Communication is approx. 1 min.-timed.
Room-to-room communication
1. Press CALL button once. Call verbally the rest station(s).
2. The called station(s) sounds a pretone and voice.
3. To answer, press TALK button once, and reply handsfree.
4. At the end, press TALK button. NOTES: Communication is approx. 1 min.-timed.
English
Français
Deutsch
Español
Nederlands
Transfer door call
1. While answering door, press CALL (Room call) button. After sounding a pretone, speak to the rest station(s).
2. At the called station(s), a pretone sounds, and both image and audio of door are activated.
3. Transferred station answers by pressing once TALK button. To end, press TALK button again. (The channel with door station is held approx. 45 sec.)
4. Communicate with door station after pressing TALK button. Lastly, press TALK button for standby.
Transfer door call
1. While answering door, press CALL (Room call) button. After sounding a pretone, speak to the rest station(s).
2. At the called station(s), a pretone sounds, and both image and audio of door are activated.
3. Transferred station answers by pressing once TALK button. To end, press TALK button again. (The channel with door station is held approx. 45 sec.)
4. Communicate with door station after pressing TALK button. Lastly, press TALK button for standby.
Transfer door call
1. While answering door, press CALL (Room call) button. After sounding a pretone, speak to the rest station(s).
2. At the called station(s), a pretone sounds, and both image and audio of door are activated.
3. Transferred station answers by pressing once TALK button. To end, press TALK button again. (The channel with door station is held approx. 45 sec.)
4. Communicate with door station after pressing TALK button. Lastly, press TALK button for standby.
Transfer door call
1. While answering door, press CALL (Room call) button. After sounding a pretone, speak to the rest station(s).
2. At the called station(s), a pretone sounds, and both image and audio of door are activated.
3. Transferred station answers by pressing once TALK button. To end, press TALK button again. (The channel with door station is held approx. 45 sec.)
4. Communicate with door station after pressing TALK button. Lastly, press TALK button for standby.
English
Français
Deutsch
Español
- 9 -
Transfer door call
1. While answering door, press CALL (Room call) button. After sounding a pretone, speak to the rest station(s).
2. At the called station(s), a pretone sounds, and both image and audio of door are activated.
3. Transferred station answers by pressing once TALK button. To end, press TALK button again. (The channel with door station is held approx. 45 sec.)
4. Communicate with door station after pressing TALK button. Lastly, press TALK button for standby.
Nederlands
5-7
For JA-2M(E)CD system
Turning on/off Alarm (activated by Motion-detect sensor camera)
In standby, keep pressing TALK button for 5 seconds or more. Release TALK button, after the SET tone is heard as follows;
TONE Peeh Alarm is off. Prrr (3 sec.) Alarm is sensor-activated.
NOTES: The Alarm ON/OFF can not be changed during
For JA-2M(E)CD system
Turning on/off Alarm (activated by Motion-detect sensor camera)
In standby, keep pressing TALK button for 5 seconds or more. Release TALK button, after the SET tone is heard as follows;
TONE STATUS OF SETTING Peeh Alarm is off. Prrr (3 sec.) Alarm is sensor-activated.
NOTES: The Alarm ON/OFF can not be changed during
For JA-2M(E)CD system
Turning on/off Alarm (activated by Motion-detect sensor camera)
In standby, keep pressing TALK button for 5 seconds or more. Release TALK button, after the SET tone is heard as follows;
TONE Peeh Alarm is off. Prrr (3 sec.) Alarm is sensor-activated.
NOTES: The Alarm ON/OFF can not be changed during
STATUS OF SETTING
communication. After the power is turned back on (when power failed, etc.), the station is put back to Alarm ON mode.
communication. After the power is turned back on (when power failed, etc.), the station is put back to Alarm ON mode.
STATUS OF SETTING
communication. After the power is turned back on (when power failed, etc.), the station is put back to Alarm ON mode.
English
Français
Deutsch
For JA-2M(E)CD system
Turning on/off Alarm (activated by Motion-detect sensor camera)
In standby, keep pressing TALK button for 5 seconds or more. Release TALK button, after the SET tone is heard as follows;
TONE STATUS OF SETTING Peeh Alarm is off. Prrr (3 sec.) Alarm is sensor-activated.
NOTES: The Alarm ON/OFF can not be changed during
communication. After the power is turned back on (when power failed, etc.), the station is put back to Alarm ON mode.
For JA-2M(E)CD system
Turning on/off Alarm (activated by Motion-detect sensor camera)
In standby, keep pressing TALK button for 5 seconds or more. Release TALK button, after the SET tone is heard as follows;
TONE STATUS OF SETTING Peeh Alarm is off. Prrr (3 sec.) Alarm is sensor-activated.
NOTES: The Alarm ON/OFF can not be changed during
communication. After the power is turned back on (when power failed, etc.), the station is put back to Alarm ON mode.
Español
Nederlands
TECHNICAL PRECAUTIONS PRÉCAUTIONS TECHNIQUES TECHNISCHE VORSORGEMASSNAHMEN PRECAUCIONES TÉCNICAS TECHNISCHE VOORZORGSMAATREGELEN
TECHNICAL PRECAUTIONS
* Operating temperature: 0°C ~ 40°C (+32°F ~ +104°F). * Cleaning: Clean the units with a soft cloth dampened with
neutral household cleanser. Do not use any abrasive cleaner or cloth.
* In case of system malfunction, turn off the power switch at
master station. If this doesn't solve the problem, shut DC power down, and contact a qualified technician.
TECHNICAL PRECAUTIONS
* Operating temperature: 0°C ~ 40°C (+32°F ~ +104°F). * Cleaning: Clean the units with a soft cloth dampened with
neutral household cleanser. Do not use any abrasive cleaner or cloth.
* In case of system malfunction, turn off the power switch at
master station. If this doesn't solve the problem, shut DC power down, and contact a qualified technician.
TECHNICAL PRECAUTIONS
* Operating temperature: 0°C ~ 40°C (+32°F ~ +104°F). * Cleaning: Clean the units with a soft cloth dampened with
neutral household cleanser. Do not use any abrasive cleaner or cloth.
* In case of system malfunction, turn off the power switch at
master station. If this doesn't solve the problem, shut DC power down, and contact a qualified technician.
English
Français
Deutsch
- 10 -
TECHNICAL PRECAUTIONS
Español
* Operating temperature: 0°C ~ 40°C (+32°F ~ +104°F). * Cleaning: Clean the units with a soft cloth dampened with
neutral household cleanser. Do not use any abrasive cleaner or cloth.
* In case of system malfunction, turn off the power switch at
master station. If this doesn't solve the problem, shut DC power down, and contact a qualified technician.
TECHNICAL PRECAUTIONS
Nederlands
* Operating temperature: 0°C ~ 40°C (+32°F ~ +104°F). * Cleaning: Clean the units with a soft cloth dampened with
neutral household cleanser. Do not use any abrasive cleaner or cloth.
* In case of system malfunction, turn off the power switch at
master station. If this doesn't solve the problem, shut DC power down, and contact a qualified technician.
SPECIFICATIONS SPÉCIFICATION TECHNISCHE DATEN ESPECIFICACIÓNES TECHNISCHE GEGEVENS
SPECIFICATIONS
• Power source:
• Consumption:
• Calling:
• Communication:<AUTO>
<MANUAL>
• Dimensions:
• Weight:
SPECIFICATIONS
• Power source:
• Consumption:
• Calling:
• Communication:<AUTO>
<MANUAL>
• Dimensions:
• Weight:
SPECIFICATIONS
• Power source:
• Consumption:
• Calling:
• Communication:<AUTO>
<MANUAL>
• Dimensions:
• Weight:
Supplied from master station (DC18V). (MAX) 120mA. Chime tone, 30 sec. approx.
Handsfree voice-actuated Press to talk, release to listen 210H x 82W x 40D(mm). (8-1/4"H x 3-1/4"W x 1-9/16"D) 270g (0.6 lbs.) approx.
Supplied from master station (DC18V). (MAX) 120mA. Chime tone, 30 sec. approx.
Handsfree voice-actuated Press to talk, release to listen 210H x 82W x 40D(mm). (8-1/4"H x 3-1/4"W x 1-9/16"D) 270g (0.6 lbs.) approx.
Supplied from master station (DC18V). (MAX) 120mA. Chime tone, 30 sec. approx.
Handsfree voice-actuated Press to talk, release to listen 210H x 82W x 40D(mm). (8-1/4"H x 3-1/4"W x 1-9/16"D) 270g (0.6 lbs.) approx.
English
Français
Deutsch
SPECIFICATIONS
• Power source:
Supplied from master station
Español
(DC18V).
• Consumption:
• Calling:
• Communication:<AUTO> <MANUAL>
• Dimensions:
(MAX) 120mA. Chime tone, 30 sec. approx.
Handsfree voice-actuated Press to talk, release to listen 210H x 82W x 40D(mm). (8-1/4"H x 3-1/4"W x 1-9/16"D)
• Weight:
SPECIFICATIONS
• Power source:
270g (0.6 lbs.) approx.
Nederlands
Supplied from master station (DC18V).
• Consumption:
• Calling:
• Communication:<AUTO> <MANUAL>
• Dimensions:
(MAX) 120mA. Chime tone, 30 sec. approx.
Handsfree voice-actuated Press to talk, release to listen 210H x 82W x 40D(mm). (8-1/4"H x 3-1/4"W x 1-9/16"D)
• Weight:
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving
270g (0.6 lbs.) approx.
- 11 -
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving
- 12 -
Loading...