Aiphone IS-IP4DVF User Manual

IS-IP4DVF

IP Video Door Station with 4 Call Buttons

-INSTRUCTIONS-

The IS-IP4DVF is an IS Series IP video door station with 4 call buttons for selective calling. The

IS-IPRY8 adaptor is required for assigning the call buttons to specic master stations within the IS-IP
conguration (refer to the IS-IPRY8 programming manual for programming instructions).

The IS-IP4DVF will connect to a network switch, and the call buttons will connect to the IS-IPRY8
adaptor inputs.

IS-IP4DVF

PACKAGE CONTENTS:

NAMES & FUNCTIONS:

1. Camera 5. Directory card

1

2

2. Microphone 6. Call status indicator

3. LED illuminator 7. Call buttons with integrated

4. Speaker name placard

3

4

5

6

FEATURES:

• IP video door station

• 4 call buttons for selective calling to master stations
(IS-IPRY8 adaptor required)

• LED call status indicator

7

• 5 name placards

• Stainless steel faceplate with tamper resistant screws

INSTALLATION:

IS-IP4DVF
4 Call Button
Door Station

SA-1 x 3

Security Driver

Blank name

placard x5

Flush backbox &

tamper resistant screws

• For ush mounting, cut a hole in the wall and use the

supplied back box.

Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D

• For surface mounting, use the SBX-ISDVFP surface
mount box. This box can mount to a standard 1 gang
box or to any at surface.

Note:

When installing the IS-IP4DVF in the supplied back box, the call
button assembly may come loose. Push call button assembly
back in to position as necessary.

Pg. 1

WIRING DIAGRAM:

IS-IPMV IS-IPMV

IS-IP4DVF

IS-IPMV

CAT-5e

CAT-5e CAT-5e

CAT-5e

IS-IPMV

Back View

CAT-5e

NO
COM
NC

To Strike
& Power

SA-1 modules are included to protect the
IS-IPRY8 adaptor from surge. Locate the
SA-1 modules near the IS-IPRY8 adaptor
and connect the ground terminal on each

SA-1 to an earth ground.

CAT-5e

~

~

~

SA-1 SA-1 SA-1

~

~

I1
I2
I3
I4

G
G

~

-

+

Power

IS-IPRY8

Note: Refer to the IS-IPRY8

Programming Manual for
information on programming

the adaptor.

PROGRAMMING:

The IS-IP4DVF door station must be set as a host or client device like any other IS-IP door station or master
station. The unit must be registered to the IS-IP system before it can be programmed to call a master station
using the call buttons and IS-IPRY8 adaptor. Refer to Steps 5-7 in the IS Series IP Direct System Programming
Guide for information on setting client and host devices and registering IP stations.

SPECIFICATIONS:

Camera unit: CMOS camera
Scanning line: 525 lines
Min. illumination: 5 Lux at 1’6”
Terminations: RJ45 jack for audio/video
Screw terminals for door release and call buttons
Operating Temp: 14° ~ 140°F / -10° ~ 60°C
Wiring Distance: 328’ with CAT-5e/6 cable to switch
Dimensions: 12-3/8” H x 7” W
w/SBX-ISDVFP: 12-7/16” H x 7-1/16” W x 2-13/16” D (top), 1-13/16” D (bottom)

FCC WARNING:

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.

• For proper regulatory compliance, the drain wire should be disconnected at the power
supply end of the cable.

• Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Aiphone Corporation

1700 130th AVE NE
Bellevue, WA 98005
[phone]
Fax: [phone]

TOLL FREE TECHNICAL SUPPORT:

[phone]

E-MAIL: [e-mail]

Pg. 2
IS-IP4DVF Instr.
0313JD