Aiphone IS-DVF-RP10 User Manual

IS-DVF-RP10

Vandal Resistant Color Video Door Station

with Built in HID multiCLASS SE® Card Reader

-INSTRUCTIONS-

The IS-DVF-RP10 is an IS Series color video door station with a multiCLASS SE® Card Reader built onto the same stainless steel faceplate. The card reader provides electronic access to a building through a separate Access Control System, which is not supplied by Aiphone. The IS-DVF-RP10 can connect to the IS-CCU or IS-SCU control units.

IS-DVF-RP10

PACKAGE CONTENTS:

NAMES & FUNCTIONS:

1. Camera 5. Name Placard

2. Microphone 6. Call status indicator

3. LED Light 7. Call button

4. Speaker 8. multiCLASS SE® Reader

FEATURES:

• All-in-one solution: Communication product & card reader

• If a card is missing or malfunctioning, audio/video communication can provide user

verication

• Standard Wiegand output to access panel

• Convenience of installing combined components

STEADY GREEN INDICATES CALL ANSWERED

IS-DVF-RP10

Vandal-resistant Door Station

Blank name

placard

INSTALLATION:

Security Driver

• For ush mounting, cut a hole in the wall and use the supplied back box. Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D

• For surface mounting, use the SBX-ISDVFP surface mount box. This box can mount to a standard 1 gang box or to any

at surface.

Flush backbox &

tamper-resistant screws

Pg. 1

WIRING DIAGRAM:

IS-DVF-RP10

NO COM NC

To Strike & Power

IS-MV

CAT-5e

Connect the reader to the host according to the wiring table below and the host installation guide.

Pigtail Discription

Yellow Beeper Input Orange Green (GRN) LED Input Black Ground (RTN) Red +VDC Drain Unused Brown Red LED Input Blue Hold Input

IS-CCU

Pigtail Discription

Red/Grn GPIO1 (RS232-T/RS485-A) Tan GPIO2 (RS232-R/RS485-B) Violet Open Collector Output White Wiegand Data 1 / Clock Green Wiegand Data 0 / Data Pink GPIO3 (RS485-Z) Gray GPIO4 (RS485-Y)

IS-PU-UL

TESTING & OPERATION:

• When power is applied to the reader, the LED will turn RED while the beeper beeps

simultaneously 3 times (the last tone is a higher frequency). The LED will then ash once after the

last tone. This indicates that the microcontroller is operating properly.

• Present an ID card to the reader (hold card directly in front of reader). The LED will momentarily turn green while the beeper beeps once, indicating that the card was read successfully.

SPECIFICATIONS:

CARD READER:

Reader model: RP10 Power Source: 5 ~ 16V DC Current: 75mA (Avg); 200mA (peak) Transmit Freq. 13.56 MHz & 125 kHz Terminations: Color-coded pre-wired pigtail Wiring Distance: 500’ Operating Temp: -31° ~ 150°F / -35° ~ 65°C Operating Humidity: 5-95% relative humidity non-condensing

FCC WARNING:

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference that may cause undesired operation.

• For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable.

• Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• The Reader is intended to be powered from a limited power source output of a previously certifed power supply

CAMERA:

Camera unit: CMOS camera Scanning line: 525 lines Min. illumination: 5 Lux at 1’6” Terminations: RJ45 jack for audio/video Screw terminals for door release Operating Temp: 14° ~ 140°F / -10° ~ 60°C Wiring Distance: 980’ with Cat5e/6 cable Dimensions: 12-3/8” H x 7” W w/SBX-ISDVFP: 12-13/16” H x 7-1/16” W x 2-13/16” D (top), 1-13/16” D (bottom)

Aiphone Corporation

www.aiphone.com/home tech@aiphone.com P: 800.692.0200

Pg. 2 IS-DVF-RP10 Instr. 0615JD