Aiphone HID-SS User Manual

HID Proximity Reader Module for 2-Gang Entrance Panel

- INSTRUCTIONS -

The HID-SS is a 2-gang stainless steel unit that contains an HID ProxPoint® Plus Card Reader. This module installs
next to any one of Aiphone’s 2-gang stainless steel sub stations (-SS and -SSR series*), creating a unified look with the
intercom and card reader installed together. Horizontal and vertical surface mount boxes are available for mounting both
units. The HID-SS does not need to be used with an intercom station. The card reader provides electronic access to a
building through the standard Access Control system, which is not supplied by Aiphone.

INSTALLATION:

1. Install HID-SS alongside of or below the 2-gang intercom sub station.

2. The HID-SS will mount into the SBX-2BH, SBX-2BV, SBX-2G, or any standard 2-gang box or ring.

3. Secure wire connections as shown on wiring chart.

4. Cut any unused wire so that bare wires are not exposed.

5. Refer to standard product installation manuals for complete syste m information. No additional information
pertaining to the Access Control system is provided by Aiphone.

* See matching models numbers on page 2,
or see Aiphone Catalog for more information.

LED indicator

Connecting the Reader to the Host:

Connect the reader to the host according to the
wiring table below and the host installation guide.

HID-SS

(front view)

Wiegand Wire Color
+ DC Red
Ground Black

--- Violet
Data0 Green
Data1 White
Shield Ground Drain
Green LED Orange
Red LED Brown
Beeper Yellow
Hold Blue

18" pigtail cable

HID-SS

(back view)

To Host

Page 1

TYPICAL LAYOUTS:

2-gang sub and HID-SS
Mounted vertically in
SBX-2BV vertical
surface mount box

2-gang sub and HID-SS
mounted in SBX-2BH
horizontal surface mount box

TESTING AND OPERATION:

When power is applied to the card reader, the LED will flash green three (3) times while
the beeper beeps simultaneously. The LED will then turn red. This indicates that the
microcontroller is operating properly.

Present an ID card to the reader. (Hold card directly in front of reader.) The LED will
momentarily turn green while the beeper beeps once, indicating that the card was read
successfully.

SPECIFICATIONS:

Reader: 6005B Series
Power Source: 5.0 – 16.0 VDC
Absolute Max. Voltage: 18 VDC
Peak Current: 80 mA
Avg. Current 5V or 12V: 20 mA
Terminations: Color-coded pre-wired pigtails
Wiring Distance: 500'
Dimensions (H x W x D): 4 ¾” x 4 3/4" x 7/8"
Operating Temperature: -10° ~ 60° C / 14° ~ 140° F

INTERCOM SYSTEM: MATCHING

LEM, LEF, LAF-C/CA,
AP-M, MP-S series: LE-SS/A, LE-SSR

NEM, NDR, NDRM series: NE-SS/A, NE-SSR
IE, TC-M, TD-H,

KB Audio door stn: IE-SS/A, IE-SSR
For additional options, please contact Aiphone

Technical Support.

HID-SS without
intercom sub station
(with optional SBX-2G
surface mount box)

SUB STATIONS:

FCC WARNING:

This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.

For proper regulatory compliance, the drain wire should be disconnected at the
power supply end of the cable.

Changes or modifications not expressly approved by the party responsibl e for
compliance could void the user’s authority to operate the equipment.

The Reader is intended to be powered from a limited power source output of a
previously certified power supply.

Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
[phone]
FAX [phone]

TOLL FREE TECHNICAL SUPPORT:

[phone]

E-MAIL: [e-mail]

HID-SS Instr.

0913JD