Aiphone DL-10 User Manual

AiPHONE

DOOR-PHONE

APARTMENT HOUSE INTERCOM SYSTEM

FOR APARTMENT BUILDINGS OF 50 SUITES OR LESS

INSTRUCTIONS

NAMES AND FUNCTIONS

'1,/ Speaker (2; Microphone (3) Amplifier '.4J Cal! switch

Handset microphone Handset speaker

(f' Body

Door release switch

(91 Straight cord (coil cord available

if ordered specially)

SPECIFICATIONS:

* Power source: DC 9 volt. Use PS-2S power supply.

* Current consumption; 80 MA during conversation (DC).

Calling: Communication:

Riser wiring;

45 MA for ring circuit (DC). Push button selection at door station. Hands free loudspeaking at door station.

Simultaneous conversation telephone-type room station. 3 common plus 1 per suite. (Additional two wires may be required when installing

EL-9S electric door release)

FEATURES:

* No push to talk switch; easy to use telephone-type station in suite and hands free loudspeaker/microphone at door. * One power supply only needed to supply communication power and door release power.

* Door stations may be parallel for multiple door installations.

INSTALLATION

Do not attempt to install your intCTcom system until you have read and thoroughly understood the installation

procedure. Aiphone's warranty is void if system is installed in a manner other than as described in this manual.

-1 —

WIRING

Lay out your system in advance. We recommend that spare conductors be included in each riser to eliminate the

possibility of removing all of the cable should a conductor prove defective.

Refer to the chart below and select the proper gauge wire to meet your requirements.

ЮТЕ; If 22 AWG is used, we suggest that 2 conductors be used on each b & L, to give more current to electric strike.

Wiring is simple and straight forward. Refer to the drawing and make connections as indicated. ‘B’ terminal on each phone completes ring circuit to door station and is the only wire in the riser that is not common. Connect ‘B’ wire from each phone to whichever push button you desire at door station to provide a directory layout that meets your requirements.

AWG WIRE SIZE DISTANCE

DIAMETER OF WIRE DISTANCE

22 AWG 20 AWG 18 AWG

1100' 1650'

0.65 mm 0.8 mm 330 mm 500 m

2500'

1.0 mm 800 m

EQUIPMENT AVAILABLE FOR USE WITH YOUR DOOR-PHONE APARTMENT HOUSE INTERCOM

DL—20S w/o call buttons: Black plate with back box. Punched for 20 call buttons.

(Available only in U.S.A.)

D: Call button complete with plastic covered slot for name.

ST—2: Blanking strip - to cover unrequired

holes. Will cover two horizontally. (Available only in U.S..A.)

TA—K Type A: Heavy duty apartment tele

phone. May be placed on desk or table, or may be mounted on standard one gang

switch box. Includes button to operate

electric door release.

TA—K Type A w/coil cord:

Apartment telephone with coil cord. (Please specify when ordering).

DN-4

iiaiüiiiiiti;; 1! Mill nil! II:!

• •

' • 0

0 •

üit

DL-10

"at*

~*'0

• •

DN— : Door station with back box with speaker and microphone. For apartment building of 4 suites or less.

DN—0: Includes no call buttons.

DN—1: Includes 1 call button. DN—2: Includes 2 call buttons. DN—3: Includes 3 call buttons. DN—4: Includes 4 call buttons.

DL— ; Door station with back box with speaker and microphone. For apartment building of 6 suites or more. DL—0: Includes no call buttons. DL—6: Includes 6 call buttons. DL—10; includes 10 call buttons.

DL—20S; Call button panel complete with

back box and 20 call buttons. Designed for use in conjunction with DL door station. Allows up to 20 suites selections with DL-0 and up to 30 suites selections with DL-10.

DIMENTIONS

PS—2S; Power supply for system.

Provides 9V DC for communication and

12V AC for door relea.se operation.

TA-K Type A

-2-

EL—9S: Electric door release.

■ m

: iT>

. .ten

PS-2S

64 mm (2-F")

+ 2 hidden pages