Page 1
INSTRUCTION MANUAL
BLENDER WBL-003
Ningbo Winlim Electric Appliance Co., Ltd
Page 2
IMPORTANT SAFETY INSTRUCTIONS
1. To protect against electrical shock, do not submerge the appliance or allow
2. This appliance is not intended for use by persons (including children) with
3. DO NOT allow young children to operate the appliance or use as a toy.
4. Never let the appliance operate unattended.
5. Remove the power cord from the electrical outlet when not in use, before
6. DO NOT abuse the power cord. Never carry the appliance by the power
7. DO NOT operate any appliance with a damaged cord or plug, or after the
8. If the power cord is damaged, it must be replaced by the manufacturer, a
9. DO NOT let the power cord hang over the edge of table or counter or touch
10. Always use appliance on a dry, level surface. Sinks, drain boards or
For Household Use Only
WHEN USING ELECTRICAL APPLIANCE, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR BLENDER
WARNING:
the power cord to come into contact with water or any other liquid.
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Close supervision is necessary when any appliance is used by or near
children.
assembling or disassembling parts and before cleaning. To unplug, grasp the
plug and pull from the electrical outlet. Never pull from the power cord.
cord or yank it to disconnect from electrical outlet; instead grasp the plug and
pull to disconnect.
appliance malfunctions, has been dropped or damaged in any manner.
certified service agent or similarly qualified persons in order to avoid a hazard.
hot surfaces such as the stove.
uneven surfaces must be avoided.
Page 3
11. Keep hands, hair, clothing, as well as utensils out of jar while processing to
reduce the risk of severe injury to persons or damage to the appliance. A
12. CAUTION: Blade assembly is sharp, handle with care. When handling
13. Avoid contact with moving parts.
14. DO NOT attempt to sharpen blades.
15. DO NOT use the appliance if blade assembly is bent or damaged.
16. To reduce risk of injury, never place the blade assembly on the base
17. DO NOT operate this appliance on or near any hot surface (such as gas or
18. The use of attachments or accessories not recommended or sold by the
19. DO NOT remove the jar from the motor base while the appliance is
20. To reduce the risk if injury, NEVER operate the appliance without the blade
21. DO NOT expose jars to extreme temperature changes.
22. CAUTION: DO NOT PROCESS HOT FOODS OR HOT LIQUIDS.
23. DO NOT overfill.
24. DO NOT operate the appliance empty.
25. If the appliance overheats, a thermal switch will become activated and
26. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not
scraper may be used but only when the appliance is not running.
the blade assembly, always hold by the base of the blade assembly.
without the proper attachment.
electric burner or in a heated oven).
manufacturer may cause fire, electric shock or personal injury.
running.
assembly in place; DO NOT try to defeat the interlock mechanism; make sure
that the attachment is properly installed before operating the appliance.
shut off the motor. To reset, unplug the appliance and let it cool down for
approximately 30 minutes before using again.
use this appliance for anything other than its intended use. Do not use
outdoors.
Page 4
27. Appliance accessories are not intended to be used in the microwave. Do
not place the jar or the lid in the microwave as it may result in damage to the
28. Check the voltage indicated on the appliance corresponds to the local
29. Never immerse the motor unit in water or any other liquid, not rinse it
30. Unplug the appliance immediately after use.
31. Keep the appliance out of the reach of children.
32. Always unplug the appliance before you start cleaning the appliance.
33. Do not use the attachment that other manufacturer produces or other
34. To avoid occurring danger, please assemble product correctly.
35. Make sure the blade is securely fastened to the accessories before you
36. Do not attempt to repair or disassemble the appliance. There are no
37. Extreme caution is necessary when moving any appliance containing hot
38. Do not use the jars in microwave.
39. Be careful if hot liquid is poured into the blender as it can be ejected out of
accessories.
mains voltage before you connect the appliance.
under the tap. Use only a moist cloth to clean the motor unit.
parts.
assemble them onto the motor unit.
user-service able parts.
liquids.
the appliance due to a sudden steaming.
NOTE: The product and its packaging have been manufactured from valuable
materials that can be recycled. This reduces the amount of refuse and helps to
preserve the environment.
Dispose of the packaging in the proper manner. Make use of the local facilities
provided for collecting paper, cardboard and lightweight packaging by type.
WARNING: Extension cords are not recommended for use with this
product.
Page 5
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Voltage:220~240V 50/60Hz
Power: 1200W
Jar Capacity:
0.5L
0.7L
1.0L
NOTE: As a result of continual improvements, the design and specifications of
the product within may differ slightly to the unit illustrated from the packaging.
Page 6
Contents
Getting to know your blender -------------------------------------Before first use--------------------------------------------------------Use-----------------------------------------------------------------------Suggested Uses------------------------------------------------------Care & Maintenance-------------------------------------------------Troubleshooting Guide----------------------------------------------Replacement Parts---------------------------------------------------Warranty & Registration---------------------------------------------
Page 7
Getting To Know Your Appliance
A B
C D E
F G
A Seal Lid B Sip & Seal Lid
C 1.0L Jar D 0.7L Jar
E 0.5L Jar F Motor Base
G Blade Assembly
NOTE: Attachments are interchangeable.
The blender is a high powered innovative tool with a compact design and
outstanding performance. It is perfect for ice crushing, chopping, blending and
nutrient and vitamin extracting. Blend and go with the convenient Sip & Seal
lids, create delicious drinks to get you out the door quickly! Best results are
achieved when you Pulse.
Page 8
Welcome to the Winlim Nutri-iQ Experience! The Winlim Nutri-iQ Features
pre-programmed settings that take the guesswork out of drink making. These
programs are timed to deliver consistent, delicious results that finish on their
own so all you have to do is press a button and enjou!
FEATURES:
Nutrient & Vitamin Extraction
1200 Watt Motor
User Interface:
START/STOP
Press once to start continuous running, press again to stop.
Timer counts up by seconds, up to 60 seconds.
PULSE
Runs only while pressed down. Short presses make short pulses.
Timer counts up by seconds as long as pressed down.
NUTRI-iQ BLEND
Pulses and blends fresh or softer ingredients to create consistent
results. Timer counts down.
NUTRI-iQ ULTRA BLEND
Pulses and blends frozen, fibrous or hard ingredients to create smooth
consistent results. Timer counts down.
Personalized, healthy drinks and juices on the go
BPA free Jars
Page 9
BEFORE FIRST USE
1. Remove all packaging material and labels from the appliance.
2. Wash the lids, jars and attachments in warm, soapy water with a soft cloth.
3. Rinse and dry thoroughly
4. Jars, lids and attachments are all dishwasher safe. It is recommended that
5. Wipe the motor base clean with a damp cloth.
Before using your appliance for the first time, it is important that you read and
follow the instructions in this use and care booklet, even if you feel you are
familiar with this type of appliance.
Your attention is drawn in particular to the section dealing with the appliance.
Find a safe and convenient place to keep this booklet handy for future
reference. This appliance has been designed to operate from a standard
domestic power outlet. It is not intended for industrial or commercial use.
Carefully unpack the appliance. Remove all packing materials and either
discard or retain for future using.
Ensure that the voltage of your electricity supply is the same as that indicated
on the rating label of the appliance. Remove the plastic accessories and wash
them in warm soapy water. Dry thoroughly and replace. Wipe over the exterior
of the Motor Base with a damp sponge or cloth. Do not use abrasive cleaners.
PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN
USING THE APPLIANCE:
IMPORTANT: Attachments are interchangeable.
CAUTION: Blades are sharp! Use extreme caution when handling the blade
assemblies. Always hold them by the base of the blade assembly.
IMPORTANT: Never run the appliance empty.
CAUTION: Never attempt to remove the jar while the appliance is still running.
WARNING: Never leave the appliance unattended while in use.
Use caution when washing the blade assemblies as the blades are very
sharp.
the lids and attachments be placed on the top rack. Ensure that the
attachments are removed from the jars before placing in the dishwasher.
Page 10
Use
ASSEMBLY
REMOVAL
Fig. 1 Fig. 2 Fig. 3
Fig 4 Fig 5 Fig 6
Page 11
IMPORTANT: Place the motor base on a clean, dry, level surface such as a
1. Make sure that the motor base is plugged in for use.
2. Add ingredients to the jar.
3. Place the blade onto the jar and twist it on tightly until you have a good
4. Turn the jar upside down and place it onto the motor base, aligning the tabs
5. Press one of the buttons to activate. (Fig.3)
6. To remove the jar, ensure that the motor has stopped running. Then turn
7. Turn the jar upright and remove the Blade Assembly by twisting the blade
8. Twist the Sip & Seal lid onto the jar to enjoy your drink on the go. Press flip
9. Make sure that the motor base is unplugged when not in use.
10.To remove the motor base unit, tip the unit forward from the rear to easily
counter or table top.
No lights will turn on.
NOTE: Do not overfill! To avoid spilling, do not add ingredients past the “Max”
fill line.
seal.(Fig. 1)
on the jar with the motor base, aligning the tabs on the jar with the motor
base. Turn it clockwise, until you feel it click into place. The unit is ready for
use.(Fig. 2)
NOTE: When using the Nutri-iQ presets, the unit will operate using pulses,
pauses and continuous runs. The pauses allow the contents of the cup to
settle. When the timer reaches “0”, it will stop by itself.
the jar counter clockwise. .(Fig. 4) and pull straight up to remove(Fig. 5)
assembly counter clockwise. Be sure to store the Blade Assembly attached
to an empty jar when not in use.
top cap firmly into the opening to get the best seal. The flip top cap locks
open when pressed backward.
disengage the suction cups.
Page 12
SAFETY FEATURES
PURPOSE
SUGGESTED JAR
TYPE OF FOOD
Chopping
0.5L
0.7L
Nuts
Chocolate
Grating
0.5L
Cheese
Bread Crumbs
Mixing
0.5L
0.7L
Batters
Dips
Sauces
0.7L
1.0L
Vinaigrettets
Salad Dressings
Simple Sauces
Frozen Blending
0.5L
0.7L
1.0L
Ice
Frozen Fruit
Ice Cream
Nutrient Juices/Smoothies
0.5L
0.7L
1.0L
Fruits
Vegetables
Leafy Greens
Built-in safety lock
The blender has a built-in safety lock feature. This ensures that you can only
switch on the appliance while the cup and the blade subassembly are
assembled on the motor base securely. If the appliance is correctly assembled,
the built-in safety lock will be unlocked.
IMPORTANT: In the base of each blade’s collar, there is a silicone gasket seal
that creates an airtight fit with the jars. After dishwashing and before each use,
always check to make sure the gasket is properly in place, as the heat from
some dishwashers may cause the gasket to become loose.
WARNING: Do not operate the motor continuously for more than 60 seconds
at a time. Allow the motor to rest for 180 seconds before continuing.
NOTICE: If the blade is not running smoothly, stop the product and add some
liquid, or reduce the ingredients in the cup.
NOTE: To prevent product overheating, dry ingredients must not be processed
for more than 30 seconds at a time.
：
Suggested Uses
CAUTION: DO NOT process dry ingredients without adding liquid to the jar.
This product is not intended for dry blending.
Page 13
Care & Maintenance
1. Separate/remove all parts from each other.
2. Clean the motor base with a slightly damp cloth and wipe dry
3. Place jars in the dishwasher. Place the lids and attachments on the top rack.
4. Whenever possible, rinse parts immediately after processing to make
5. Store the product in a cool, dry place.
HOW TO CLEAN
CAUTION: Make sure that the motor base is unplugged from the power source
before inserting or removing any attachment and before cleaning.
NOTICE: Wait until the blender has cooled down sufficiently before cleaning it.
CAUTION: DO NOT immerse the motor base into water or any liquid, or place
into a dishwasher.
Use caution when handling the blade assemblies as the blades are very
sharp.
cleanup easier.
NOTE:
You may also wash the jars by filling the jar to the Max fill line with warm
water and drop of dish washing detergent, placing the blade assembly on
the jar and pulsing a few times. Do not fill the jar more than Max fill line with
water because it will overflow. Once clean, remove the jar from the motor
base. Rinse the jar, attachment and lid under running water. Allow all the
parts to dry before storing.
Do not use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol, alcohol or acetone to clean the appliance
All detachable accessories can be cleaned in dishwasher.
Tips:
Use a small brush(not included) to remove particles of food lodged
underneath the blades.
If some leftover particles dry onto the inside of the jar, fill the cup about 2/3
full with warm water and attach the blade subassembly. Place the jar and
blade subassembly onto the motor base and operate the appliance for
Page 14
about 20-30 seconds to help loosen the stuck ingredients. Repeat the
1. Store the appliance upright. Do not place anything on top. Store the jars
2. Remove and empty the jar and ensure that no food is jamming the
3. Allow the appliance to cool for approximately 30 minutes.
4. Re-install the jar onto the base and re-plug the appliance into the
5. Proceed to use the appliance as before while making sure not to
PROBLEMS
POSSIBLE REASONS & SOLUTIONS
Motor doesn’t start or
attachment doesn’t rotate.
For the jars, make sure that the tabs are
seated in the slots and turned clockwise
Food is unevenly
chopped.
Either you are chopping too much food at once,
or you are not pulsing properly. Reduce the
amount of food in the jar.
Food is too finely chopped
or too watery
The food has been over processed. Use short
operating for best results.
You can not achieve snow
from ice cubes.
For best result use ice straight from the freezer.
Try using short operating instead of long one.
Make sure the jar is completely dry before
adding ice.
Jar is leaking
Make sure that your lid or blade assembly is
properly assembled to the jar. Leaking may
occur if it is misaligned when twisted onto the
jar. Turn the lid tightly clockwise.
above step but use clean tap water. Empty blender and dry thoroughly.
CAUTION: Do not attempt to remove blades from the Blade subassembly
for cleaning.
HOW TO STORE
and the rest of the attachments along side the appliance where they will
not be damaged and won’t cause a hazard.
cutting blades.
electric outlet.
exceed the recommended maximum jar capacities.
Troubleshooting Guide
Page 15
Unit doesn’t turn on
Make sure the unit is plugged in.
Make sure the blade assembly is properly
assembled to the jar and that is not misaligned
Unit doesn’t turn off
Unplug the power cord from the electrical outlet
and call customer service for support
Doesn’t mix well
Pulse ingredients for best results. Press down
on the jar in short intervals for even blending
and chopping. For frozen ingredients, pulse in
short intervals of 2-5 seconds and repeat.
Lid/blade assembly will not
properly align to the jar
Set the jar on a level surface. Place the lid or
blade assembly on top of the jar and align the
threads so that the lid/blades sit flat on the jar.
Twist clockwise so that the lid/blades evenly
align to the jar until you have a tight seal.
WARRANTY INFORMATION
This marking indicates that this product should not be
disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of
material resources. To return your used device, please
use the return and collection systems or contact the
retailer where the product was purchased. They can take
this product for environmental safe recycling.
The manufacturer provides warranty in accordance with the legislation of the
customer’s own country of residence, with a minimum of 1 year, starting from
the date on with the appliance is sold to the end user.
The warranty only covers defects in material or workmanship.
The repairs under warranty may only be carried out by an authorized service
centre. When making a claim under the warranty, the original bill of purchase
(with purchase date) must be submitted
The warranty will not be applied in case of:
- Normal wear and tear
- Incorrect use, e.g. overloading of the appliance, use of non-approved
accessories
- Use of force, damage caused by external influences.
- Damage caused by non-observance of the user manual, e.g. connection to
an unsuitable mains supply or non-compliance with the installation instructions
- Partially or completely dismantled appliances
Page 16
Loading...