AG neovo QM-65, QM-75, QM-86 Service Manual

QM-65, QM-75 & QM-86 LED-Backlit Display

User Manualdisplays.agneovo.com

TABLE OF CONTENTS

SAFETY INFORMATION .............................................................................. 1

Federal Communications Commission (FCC) Notice (U.S. Only) ............................................................1

CE ............................................................................................................................................................1

Polish Center for Testing and Certication otice ....................................................................................1

Electric, Magnetic and Electromagnetic Fields (“EMF”) ........................................................................... 2

Information for U.K. only ...........................................................................................................................3

North Europe (Nordic Countries) Information ........................................................................................... 4

End-of-Life Disposal .................................................................................................................................5

Waste Electrical and Electronie Equipment-WEEE ..................................................................................5

Turkey RoHS ............................................................................................................................................ 6

Ukraine RoHS ..........................................................................................................................................6

P RECAUTIONS ............................................................................................7

Cautions When Setting Up .......................................................................................................................7

Cautions When Using ...............................................................................................................................8

Cleaning and Maintenance .......................................................................................................................8

Notice for the LCD Display .......................................................................................................................9

CHAP TER 1: P RODUCT DESCRIP TION ..................................................... 10

1.1 Unpacking ..........................................................................................................................................10

1.2 Package Contents ..............................................................................................................................10

1.3 Preparing for the Installation ..............................................................................................................11

1.4 Wall Mounting Installation ................................................................................................................... 11

1.4.1 VESA Grid ...............................................................................................................................12

1.4.2 Ventilation Requirements for Enclosure Locating ....................................................................13

1.5 Using the Remote Sensor and Power Status Indicator ......................................................................13

1.6 LCD Display Overview .......................................................................................................................14

1.6.1 Control Panel ...........................................................................................................................14

1.6.2 Input/Output Terminals ............................................................................................................16

1.7 Remote Control .................................................................................................................................. 18

1.7.1 General Functions ...................................................................................................................18

1.7.2 ID Remote Control ...................................................................................................................20

1.7.3 Remote Control buttons on USB source ................................................................................. 21

1.7.4 Inserting the Batteries in the Remote Control .........................................................................23

1.7.5 Handling the Remote Control ..................................................................................................23

1.7.6 Operating Range of the Remote Control ................................................................................. 23

CHAP TER 2: MAKING CONNECTIONS ......................................................25

2.1 Connecting the Power ........................................................................................................................25

2.2 Connecting a Computer .....................................................................................................................27

2.2.1 Using VGA Input .....................................................................................................................27

2.2.2 Using DisplayPort Input ........................................................................................................... 28

2.2.3 Using HDMI Input ....................................................................................................................30

2.3 Connecting External Equipment (Video Player) .................................................................................31

2.3.1 Using HDMI Video Input .......................................................................................................... 31

TABLE OF CONTENTS

2.4 Connecting Audio Equipment ............................................................................................................. 33

2.4.1 Connecting an External Audio Device ..................................................................................... 33

2.5 Using the Card Reader .......................................................................................................................34

2. Connecting ultiple Displays in a Daisy-chain Conguration ............................................................ 35

2.6.1 Display Control Connection ..................................................................................................... 35

2.7 IR Connection .....................................................................................................................................36

2.8 IR Pass-Through Connection .............................................................................................................36

CHAP TER 3: USING THE LCD DISP LAY .................................................... 37

3.1 Turning on the Power .........................................................................................................................37

3.1.1 Initial Setup ..............................................................................................................................37

3.2 Selecting the Input Source Signal ...................................................................................................... 38

3.3 Adjusting the Volume ..........................................................................................................................38

3.4 Changing the Picture Format .............................................................................................................39

CHAP TER 4: USB SOURCE ........................................................................ 40

4.1 Accessing the USB Menu ...................................................................................................................40

4.2 Using the USB Menu .......................................................................................................................... 41

4.2.1 Creating a Playlist ...................................................................................................................41

4.2.2 Modifying a Playlist ..................................................................................................................43

4.2.3 Playing Files in a Playlist ......................................................................................................... 43

4.2.4 USB Menu Settings .................................................................................................................43

CHAP TER 5: ON SCREEN DISP LAY MENU ............................................... 45

5.1 Using the OSD Menu .........................................................................................................................45

5.2 OSD Menu Tree ................................................................................................................................. 47

CHAP TER 6: ADJ USTING THE LCD DISP LAY ..........................................49

6.1 Picture Settings .................................................................................................................................. 49

6.2 Screen Settings ..................................................................................................................................53

6.3 Audio Settings ....................................................................................................................................56

. Conguration1 Settings ......................................................................................................................58

.5 Conguration2 Settings ......................................................................................................................62

6.6 Advanced option Settings ...................................................................................................................64

CHAP TER 7 : AP P ENDIX .............................................................................. 7 5

7.1 Warning Messages .............................................................................................................................75

7.2 Supported Media Formats .................................................................................................................. 75

7.3 Input Mode .........................................................................................................................................77

7.4 Cleaning ............................................................................................................................................. 79

7.5 Troubleshooting ..................................................................................................................................80

7.6 Transporting the LCD Display ............................................................................................................ 81

CHAP TER 8 : SP ECIFICATIONS .................................................................. 8 4

8.1 Display Specications ........................................................................................................................84

8.2 Display Dimensions ............................................................................................................................ 85

SAFETY INFORMATION

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes or modications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.

To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive

moisture. THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE

CAUSING EQUIPMENT REGULATIONS.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: This equipment is compliant with Class A of EN55032/CISPR 32. In a residential

environment this equipment may cause radio interference.

Polish Center for Testing and Certication Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source.

The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible.

A protection mark “B” conrms that the equipment is in compliance with the protection usage requirements of

standards PN-93/T-42107 and PN-89/E-06251.

SAFETY INFORMATION

Electric, Magnetic and Electromagnetic Fields (“EMF”)

• We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.

• One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.

• We are committed to develop, produce and market products that cause no adverse health effects.

• We conrm that if its products are handled properly for their intended use, they are safe to use according to

scientic evidence available today.

• We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization for early integration in its products.

SAFETY INFORMATION

Information for U.K. only

WARNING - THIS APPLIANCE MUST BE EARTHED.

(B)

(A)

Important: This apparatus is supplied with an approved moulded 13A plug. To

change a fuse in this type of plug proceed as follows:

1 Remove fuse cover and fuse. 2 Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI

approved type.

3 Ret the fuse cover.

If the tted plug is not suitable for your socket outlets, it should be cut

off and an appropriate 3-pin plug tted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.

Note: The severed plug must be

destroyed to avoid a possible shock

hazard should it be inserted into a

13A socket elsewhere.

SAFETY INFORMATION

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”) BROWN - “LIVE” (“L”) GREEN & YELLOW - “EARTH” (“E”)

• The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW.

• The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK.

• The BROWN wire must be connected to the terminal which marked with the letter “L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires.

North Europe (Nordic Countries) Information

Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU

STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT

TILGÆNGELIGE.

Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI

IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE

FOR STØMTILFØRSEL ER LETTE Å NÅ.

SAFETY INFORMATION

End-of-Life Disposal

Your new Public Information Display contains materials that can be recycled and reused. Specialized

companies can recycle your product to increase the amount of reusable materials and to minimize the amount

to be disposed of.

Please nd out about the local regulations on how to dispose of your old display from your local dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling contact www.eia.org (Consumer Education Initiative).

Waste Electrical and Electronie Equipment-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local government

ofce, the waste disposal organization that serves your household or the store at which you

purchased the product.

Attention users in United States:

Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.mygreenelectronics.com or www.eiae.org.

End of Life Directives-Recycling

Your new Public Information Display contains several materials that can be recycled for new users.

Please dispose of according to all Local, State, and Federal laws.

Restriction on Hazardous Substances statement (India)

This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

E-Waste Declaration for India

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment . The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

SAFETY INFORMATION

Batteries

For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation.

Please contact your local authority for details on the collection and recycling schemes.

For Switzerland: The used battery is to be returned to the selling point.

For other non-EU countries: Please contact your local authority for correct method of

disposal of the used battery. According to EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall be separated to collect by local service.

Turkey RoHS

Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur.

Ukraine RoHS

Обладнання відповідає вимогам Технічного регламенту щодо обмеження використання деяких

небезпечних речовин в електричному та електронному обладнанні, затвердженого постановою Кабінету

Міністрів України від 3 грудня 2008 № 1057.

PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Symbols used in this manual

This icon indicates the existence of a potential haza rd that could result in personal injury or damage to the product.

This icon indicates important operating and servicing information.

Notice

• Read this User Manual carefully before using the LCD display and keep it for future reference.

• The product specications and other information provided in this User anual are for reference only. All information is subject to change without notice. Updated content can be downloaded from our web site at

displays.agneovo.com.

• To register online, go to displays.agneovo.com.

• To protect your rights as a consumer, do not remove any stickers from the LCD display. Doing so may affect the determination of the warranty period.

Cautions When Setting Up

• Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct sunlight.

• Do not cover or block the ventilation holes in the housing.

• Place the LCD display on a stable area. Do not place the LCD display where it may subject to vibration or shock.

• Place the LCD display in a well-ventilated area.

• Do not place the LCD display outdoors.

• To avoid the risk of shock or permanent damage to the set, do not expose the display to dust, rain, water or an excessively moist environment.

• Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes. Doing so may

cause accidental re, electric shock or damage the CD display.

PRECAUTIONS

Cautions When Using

• Use only the power cord supplied with the LCD display.

• The power outlet should be installed near the LCD display and be easily accessible.

Warning:

• If an extension cord is used with the LCD display, ensure that the total current consumption plugged into the power outlet does not exceed the ampere rating.

• Do not allow anything to rest on the power cord. Do not place the LCD display where the power cord may be stepped on.

• If the CD display will not be used for an indenite period of time, unplug the power cord from the power outlet.

• To disconnect the power cord, grasp and pull by the plug head.

Do not tug on the cord doing so may cause re or electric shock.

• Do not unplug or touch the power cord with wet hands.

• When turning off the display by detaching the power cord, wait 6 seconds before re-attaching the power cord for normal operation.

• Do not knock or drop the display during operation or transportation.

Cleaning and Maintenance

Unplug the power cord from the power outlet and

refer to qualied service

personnel under the following conditions:

 When the power cord is

damaged.

 If the LCD display has been

dropped or the housing has been damaged.

 If the LCD display emits smoke

or a distinct odor.

• To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your display, grasp the frame to lift; do not lift the display by placing

your hand or ngers on the CD panel.

• Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your display.

• If your display becomes wet, wipe it with dry cloth as soon as possible.

• If a foreign substance or water gets in your display, turn the power off immediately and disconnect the power cord. Then remove the foreign substance or water, and send the unit to the maintenance center.

• In order to maintain the best performance of your display and ensure a longer lifetime, we strongly recommend using the display in a location that falls within the following temperature and humidity ranges.

 Temperature: 0-40° C (32-104° F)  Humidity: 20-80% RH

PRECAUTIONS

Notice for the LCD Display

• In order to maintain the stable luminous performance, it is recommended to use low brightness setting.

• Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease with time.

• When static images are displayed for long periods of time, the image may cause an imprint on the LCD display. This is called image retention or burn-in.

 To prevent image retention, do any of the following:

• Set the LCD display to turn off after a few minutes of being idle.

• Use a screen saver that has moving graphics or a blank white image.

• Execute the ATI-BUR-I function of the CD display. See Congration  > P anel Saving > ANTI-BURN-IN section.

• Switch desktop backgrounds regularly.

• Adust the CD display to low brightness settings.

• Turn off the LCD display when the system is not in use.

 Things to do when the LCD display shows image retention:

• Turn off the LCD display for extended periods of time. It can be several hours or several days.

• Use a screen saver and run it for extended periods of time.

• Use a black and white image and run it for extended periods of time.

• There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be damaged and to produce spots. This is acceptable and is not considered a failure.

• IMP ORTANT: Always activate a moving screen saver program when you leave your display unattended.

Always activate a periodic screen refresh application if the unit will display unchanging static content.

Uninterrupted display of still or static images over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.

• WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. This is also not covered under the terms of your warranty.

CHAPTER 1: PRODUCT DESCRIPTION

1.1 Unpacking

• This product is packed in a packaging box which contains standard accessories.

• Any other optional accessories will be packed separately.

• Considering the size and weight of the display, it is recommended that this product is carried out by two persons.

• After opening the packaging box, ensure that the included items are in good condition and complete.

1.2 P ackage Contents

When unpacking, check if the following items are included in the package. If any of them is missing or damaged, contact your dealer.

LCD Display

Q uick Start Guide

QM-65

Quick Start Guide

QM-65 LED-Backlit Display

www.agneovo.com

QM-65_Quick Guide_V010

P ower cord

Remote control

HDMI cable

RS232 cable

Note:

 Remote control is shipped with

the supplied AAA batteries.

 For all other regions, apply a

power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the safety regulations of the particular country (Type H05W-F, 2G or

3G, 0.75 or 1 mm

should be

used).

 You might like to save the

package box and packing material for shipping the display.

 The pictures are for reference

only. Actual items may vary upon shipment.

PRODUCT DESCRIPTION

1.3 P reparing for the Installation

• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your service agent.

• The product should be installed on a at surface to avoid tipping. The distance between the back of the product and the wall should be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life of the electronic components.

• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced.

1.4 Wall Mounting Installation

Warning:

 Do not press too hard on the

LCD panel or edge of the frame, as this may cause the device to malfunction.

To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America.

To wall-mount the LCD display, screw the mounting bracket to the VESA holes at the rear of the LCD display.

Q M-65

400mm

Q M-7 5

600mm

400mm

Note:

 Avoid the wall-mounting kit to

block the ventilation holes on the back of the display.

 Secure the LCD display on a

solid wall strong enough to bear its weight.

 Lay a protective sheet on a

table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face.

 Ensure you have all

accessories for mounting this display (wall mount, ceiling mount, etc).

 Follow the instructions that

come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

PRODUCT DESCRIPTION

Q M-8 6

600mm

1.4.1 VESA Grid

400mm

Model Name VESA Grid

QM-65 400(W) x 400(H) mm QM-75 600(W) x 400(H) mm QM-86 600(W) x 400(H) mm

Caution:

To prevent the display from falling:

 For wall or ceiling installation, we recommend installing the

display with metal brackets which are commercially available. For detailed installation instructions, see the guide received with the respective bracket.

 To lessen the probability of injury and damage resulting from fall

of the display in case of earthquake or other natural disaster, be sure to consult the bracket manufacturer for installation location.

Note:

 For QM-65 wall-mounting

kits, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely.

 For QM-75 / QM-86 wall-mounting

kits, use M8 mounting screws (having a length 15 mm longer than the thickness of the mounting bracket) and tighten them securely.

 Unit without base weight is

24.8 kg (QM-65), 53.3 kg (QM-

75), or 63.8 kg (QM-86). The equipment and its associated mounting means still remain secure during the test. For use only with UL Listed Wall Mount Bracket with minimum weight/load is 32.8 kg (QM-65),

67.0 kg (QM-75), or 79.6 kg (QM-86).

PRODUCT DESCRIPTION

1.4.2 Ventilation Requirements for Enclosure Locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

100 mm

100 mm 100 mm

100 mm

1.5 Using the Remote Sensor and P ower Status Indicator

• If you want to obtain a better reception of remote control function, please adjust the indicator location to easily check the power status indicator.

• If you want to mount the display to the wall, please push the indicator switch upwards before installation.

• When adusting the indicator location, make sure to pushpull the indicator switch rmly until it clicks into place.

Push downward to reveal the indicator

Pull upward to hide the indicator

PRODUCT DESCRIPTION

1.6 LCD Display Overview

1.6.1 Control P anel

Q M-65

Q M-7 5

MUTE INPUT

192 3 4 5 6 7 8

MUTE INPUT

192 3 4 5 6 7 8

PRODUCT DESCRIPTION

Q M-8 6

] P ower

[

Turn the display on or put the display to standby.

MUTE

Switch the audio mute ON/OFF.

INP UT

Choose the input source.

[

] Increase

• Enter the submenu.

• Increase the audio output level while OSD menu is off.

[

] Decrease

• Return to the previous menu.

• Decrease the audio output level while OSD menu is off.

[

] Up

Move the highlight bar up to select an option or increase the adjustment while OSD menu is on.

MUTE INPUT

192 3 4 5 6 7 8

[

] Down

Move the highlight bar down to select an option or decrease the adjustment while OSD menu is on.

• Activate the OSD menu when OSD menu is off.

• Hide the OSD menu while OSD menu is on.

Remote control sensor and power

status indicator

• Receive command signals from the remote control.

• Indicate the operating status of the display:

- Lights green when the display is turned

- Lights red when the display is in

standby mode

- Blinks green and red when “Advanced

option, Schedule” is enabled

- Blinks red when a failure has been

detected

- Lights off when the main power of the

display is turned off

PRODUCT DESCRIPTION

1.6.2 Input/ Output Terminals

Q M-65

Q M-7 5

116 2 3 4 5 6

①②

③④

12 11

8 9

1 2 3 4 5 6

①②

③④

12 11

8 9

PRODUCT DESCRIPTION

Q M-8 6

1 2 3 4 5 6

AC IN

AC power input from the wall outlet.

Main power switch

Switch the main power on/off.

RJ 45

LAN control function for the use of remote control signal from the control center.

RS232 IN

RS232 network input for the loopthrough function.

12 11

8 9

IR OUT

①②

③④

IR signal output for the loop-through function.

VGA IN (D-Sub)

VGA video input.

AUDIO IN

Audio input for VGA source (3.5mm stereo phone).

AUDIO OUT

Audio output to external AV device (RCA).

RS232 OUT

RS232 network output for the loopthrough function.

DisplayP ort IN

DisplayPort video input.

HDMI1/ HDMI2/ HDMI3/ HDMI4 IN

HDMI video/audio input.

IR IN

IR signal input for the loop-through function.

Note:

 This display’s remote control sensor

will stop working if the [ IR IN] jack is connected.

 T o remotely control your A/V device

via this display , see page 36 for IR Pass-Through connection.

USB 2.0 / 3.0 P ORT

Connect your USB storage device.

USB 2.0 x 1 (Service Port / Media Playback)

USB 2.0 x 1 (Media Playback)

USB 3.0 x 1 (Media Playback)

USB power outlet x 1 (5V2A)

MICRO SD CARD SLOT

Insert a micro SD card into the slot.

OP S SLOT

Slot for installing the optional OPS module..

Kensington Security Slot(Q M-65 Only)

Used for security and theft prevention.

PRODUCT DESCRIPTION

1.7 Remote Control

1.7 .1 General Functions

3 4

6 7 8

[ ]

P OWER

Turn the display on or to put the display into standby mode.

P LAY

• Control playback in multimedia mode.

• Freeze feature

: Freeze hot key for all inputs content.

: Unfreeze hot key for all input content.

[ ] SOURCE

Root Menu: Go to Video source OSD.

[ ] HOME

• Root Menu: Access the OSD menu.

• Others: Exit the OSD menu.

[ ] LIST

No function.

NAVIGATION buttons

]

[

• Root Menu: Go to Smart picture OSD.

• Main Menu: Move the highlight bar up to

adjust the selected item.

• IR Daisy Chain Menu: Increase controlled Group ID number.

[

]

• Root Menu: Go to Audio source OSD.

• Main Menu: Move the highlight bar down to

adjust the selected item.

• IR Daisy Chain Menu: Decrease controlled Group ID number.

[

]

• Main Menu: Return to the previous menu page.

• Source Menu: Exit the source menu.

• Volume Menu: Decrease the volume level.

[

]

• Main Menu: Enter the submenu or conrm a

selection.

• Source Menu: Conrm the selected source.

• Volume Menu: Increase the volume level.

[ ] OK

• Root Menu: Go to IR daisy chain OSD in Primary/Secondary mode.

• Main Menu: Conrm an entry or selection.

[ ] ADJ UST

Go to Auto Adjust OSD (for VGA input only).

PRODUCT DESCRIPTION

[ ] MUTE

Turn the mute function on/off.

[ ] [ ] [ ] [ ] COLOR

• Choose tasks or options.(not supported).

•

[ Number/ ID SET/ ENTER]

• Enter text for network setting.

• Set the display ID. See 1.7.2 ID Remote Control for more detail.

[

Change the aspect ratio.

[

Return to the previous menu or exit from the previous function.

[

View the information about the display.

[

No function.

: Hot key for Window selection function.

] FORMAT

] BACK

] INFO

] OP TIONS

] [ ] VOLUME

[

Adjust the volume level.

PRODUCT DESCRIPTION

1.7 .2 ID Remote Control

You can set the remote control ID when you want to use this remote control on one of several different displays.

To set the remote control ID:

1 Press the ID button. The red LED blinks

twice.

2 Press the ID SET button for more than

1 second to enter the ID mode. The red LED lights up. Press the ID SET button again will exit the ID mode. The red LED lights off.

3 Press the digit numbers [ 0] ~ [ 9] to

select the display you want to control. For example:

• Display ID # 1: press [ 0] , [ 1]

• Display ID # 11: press [ 1] , [ 1] The numbers available are from [ 01] ~

[ 255] .

• Not pressing any button within 10

seconds will exit the ID mode.

• If an error pressing of buttons other

than the digits occured, wait 1 second after the red LED lights off and then lights up again, then press the correct digits again.

4 Press the ENTER button to conrm.

The red LED blinks twice and then lights off.

Note:

 Press the NORMAL button. The green LED

blinks twice, indicating the remote control returns to normal operation.

 It is necessary to set up the ID number for

each display before selecting its ID number.

PRODUCT DESCRIPTION

1.7 .3 Remote Control buttons on USB source

[ ]

3 4

6 7 8

P OWER

Turn the display on or to put the display into standby mode.

The button is only controlled by Scalar.

P LAY

• Control playback of media (video/photo/

music les.

To play a media le, select USB >

Compose > edit or new add playlist >

choose media les  press the

play all the media les in the playlist.

• When playing a video, press the stop playing. Press the button, to replay the video from the beginning.

• When playing a video or displaying a slideshow, press the

playing.

• All media les should be put at the folder, which is named

the root directory of the specied storage

(internal/USB/SD Card). All sub-folders (video/photo/music) are named by media types and shouldn’t be changed.

videos: { root dir of storage} / agn/ video/ photos: { root dir of storage} / agn/ photo/ music: { root dir of storage} / agn/ music/

Note that the root directories of three storages are:

Internal storage: / sdcard USB storage: / mnt/ usb_ storage SD card: / mnt/ ex ternal_ sd

button to pause

“agn” with sub-folder, under

button to

[ ] SOURCE

Choose USB as the input source. The button is only controlled by Scalar.

[ ] HOME

Access the OSD menu. The button is only controlled by Scalar.

[ ] LIST

Move the focus up to the next control or widget such as buttons.

NAVIGATION buttons

Navigate through menus and choose items.

[ ] OK

Conrm an entry or selection.

[ ] ADJ UST

Move the focus down to the next control or widget such as buttons.

PRODUCT DESCRIPTION

[ ] MUTE

Turn the mute function on/off. The button is only controlled by Scalar.

[ ] [ ] [ ] [ ] COLOR

No function. These two buttons are only controlled by Scalar.

[ Number/ ID SET/ ENTER]

ID SET/ENTER: No function. These two buttons are only controlled by Scalar.

] FORMAT

[

Change the aspect ratio. The button is only controlled by Scalar.

] BACK

[

Return to the previous menu or exit from the previous function.

] INFO

[

• Display information about current input signal. It is shown by Scalar.

• USB > Compose > edit or new add playlist >

choose any media les  press the

to show the information of the chosen media

le.

] OP TIONS

[

Open toolbar.

• USB > Compose > edit or new add playlist > press the opens on the left side of the screen.

] [ ] VOLUME

[

Adjust the volume level. The buttons are only controlled by Scalar.

button to open toolbar. Toolbar

button

PRODUCT DESCRIPTION

1.7 .4 Inserting the Batteries in the Remote Control

The remote control is powered by two 1.5V AAA batteries. To install or replace batteries:

1 Press and then slide the cover to open it.

Caution:

The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:

2 Align the batteries according to the (+ ) and (-) indications

inside the battery compartment.

3 Replace the cover.

1.7 .5 Handling the Remote Control

• Do not subject to strong shock.

• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.

• Avoid exposure to heat and steam.

• Other than to install the batteries, do not open the remote control.

1.7 .6 Operating Range of the Remote Control

Point the top of the remote control toward the display’s remote control sensor (on the left or right side) when pressing a button.

 Place “AAA” batteries

matching the (+ ) and (– ) signs on each battery to the (+ ) and (– ) signs of the battery

compartment.  Do not mix battery types.  Do not combine new batteries

with used ones. It causes

shorter life or leakage of

batteries.  Remove the dead batteries

immediately to prevent them

from liquid leaking in the

battery compartment. Don’t

touch exposed battery acid, as

it can damage your skin.

Note:

 If you do not intend to use

the remote control for a long

period, remove the batteries.

When using the remote control, the distance from the remote control to the sensor on the display should be less than 5m/16ft, and the

horizontal and vertical angles should be less than 30.

Q M-65/ Q M-7 5

30 ° 30 °

 The remote control may not

function properly when the

remote control sensor on this

display is under direct sunlight

or strong illumination, or when

there is an obstacle in the path

of signal transmission.

PRODUCT DESCRIPTION

Q M-8 6

30 ° 30 °

+ 62 hidden pages

AG neovo QM-65, QM-75, QM-86 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual