WARNING: Use of controls, adjustments or procedures other than those specied
in this documentation may result in exposure to shock, electrical hazards and/or
mechanical hazards.
Read and follow these instructions when connecting and using your display:
Operation:
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s
electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• When turning off the display by detaching the power cord, wait 6 seconds before re-attaching
the power cord for normal operation.
• Ensure the use of an approved power cord at all times. If your power cord is missing, please
contact your local service center.
• Do not subject the display to severe vibration or high impact conditions during operation.
• Do not knock or drop the display during operation or transportation.
• The eye bolt is for usage in short-time maintenance and installation. We suggest not to use
the eye bolt for more than 1 hour. Prolong usage is prohibited. Please keep a clear safety area
under the display while using the eye bolt.
Maintenance:
• To protect your display from possible damage, do not put excessive pressure on the LCD panel.
When moving your display, grasp the frame to lift; do not lift the display by placing your hand or
ngers on the LCD panel.
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped
with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or
ammonia-based liquids to clean your display.
• To avoid the risk of shock or permanent damage to the set, do not expose the display to dust,
rain, water or an excessively moist environment.
• If your display becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in your display, turn the power off immediately and
disconnect the power cord. Then remove the foreign substance or water, and send the unit to
the maintenance center.
• Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your display and ensure a longer lifetime, we
strongly recommend using the display in a location that falls within the following temperature
and humidity ranges.
-Temperature: 0-40°C 32-104°F
-Humidity: 20-80% RH
1
SAFETY INSTRUCTIONS
IMPORTANT: Always activate a moving screen saver program when you leave your display
unattended. Always activate a periodic screen refresh application if the unit will display unchanging
static content. Uninterrupted display of still or static images over an extended period may cause
“burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is a well-known
phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost
imaging” will disappear gradually over a period of time after the power has been switched off.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and
cannot be repaired. This is also not covered under the terms of your warranty.
Service:
• The casing cover should be opened only by qualied service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave your display under direct sunlight.
If your display does not operate normally, having followed the instructions set out in
this document, please contact a technician or your local service center.
Read and follow these instructions when connecting and using your display:
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen
many be wiped with a dry cloth when the power is off. However, never use alcohol,
solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate normally when you
have followed the instructions in this manual.
• The casing cover should be opened only by qualied service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat
sources.
• Remove any object that could fall into the vents or prevent proper cooling of the
display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to rain or excessive
moisture.
• When turning off the display by detaching the power cable or DC power cord, wait
for 6 seconds before re-attaching the power cable or DC power cord for normal
operation..
• To avoid the risk of shock or permanent damage to the set do not expose the
display to rain or excessive moisture.
• When positioning the display, make sure the power plug and outlet are easily
accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a
still image in high contrast remains on the screen for an extended period of time,
it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is
a well-known phenomenon that is caused by the shortcomings inherent in LCD
technology. In most cases the afterimage will disappear gradually over a period of
time after the power has been switched off. Be aware that the after-image symptom
cannot be repaired and is not covered under warranty.
2
SAFETY INSTRUCTIONS
CE
WARNING: This equipment is compliant with Class A of EN55032/CISPR 32. In a
residential environment this equipment may cause radio interference.
Polish Center for Testing and Certication Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong
socket). All equipment that works together (computer, display, printer, and so on) should have the
same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit
protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power
supply socket, which should be located near the equipment and easily accessible.
A protection mark “B” conrms that the equipment is in compliance with the protection usage
requirements of standards PN-93/T-42107 and PN-89/E-06251.
3
SAFETY INSTRUCTIONS
Electric, Magnetic and Electromagnetic Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers, which, like any electronic
apparatus, in general have the ability to emit and receive electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health and safety measures for
our products, to comply with all applicable legal requirements and to stay well within the EMF
standards applicable at the time of producing the products.
3. We are committed to develop, produce and market products that cause no adverse health
effects.
4. We conrm that if its products are handled properly for their intended use, they are safe to use
according to scientic evidence available today.
5. We play an active role in the development of international EMF and safety standards, enabling
us to anticipate further developments in standardization for early integration in its products.
Information for U.K. only
WARNING - THIS APPLIANCE MUST BE EARTHED.
Important:
(B)
(A)
This apparatus is supplied with an approved moulded 13A plug.
To change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI
approved type.
3. Ret the fuse cover.
If the tted plug is not suitable for your socket outlets, it should
be cut off and an appropriate 3-pin plug tted in its place.
If the mains plug contains a fuse, this should have a value of 5A.
If a plug without a fuse is used, the fuse at the distribution board
should not be greater than 5A.
NOTES: The severed plug must be destroyed to avoid a
possible shock hazard should it be inserted into a 13A socket
elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the
following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN & YELLOW - “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the
terminal in the plug which is marked with the letter “E” or by
the Earth symbol or coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is
marked with the letter “N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which
marked with the letter “L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip
is clamped over the sheath of the lead - not simply over the three
wires.
4
SAFETY INSTRUCTIONS
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA,
NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG
STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA
HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE
Your new Public Information Display contains materials that can be recycled and reused.
Specialized companies can recycle your product to increase the amount of reusable materials and
to minimize the amount to be disposed of.
Please nd out about the local regulations on how to dispose of your old display from your local
dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal
regulations. For additional information on recycling contact www.eia.org (Consumer Education
Initiative)
Waste Electrical and Electronie Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European
Directive 2012/19/EU governing used electrical and electronic appliances, this
product may not be disposed of with normal household waste. You are responsible
for disposal of this equipment through a designated waste electrical and electronic
equipment collection. To determine the locations for dropping off such waste electrical
and electronic, contact your local government ofce, the waste disposal organization
that serves your household or the store at which you purchased the product.
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling
information, contact: www.mygreenelectronics.com or www.eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled
for new users.
Please dispose of according to all Local, State, and Federal laws.
7
Após o uso, as pilhas
deverão ser entregues ao
estabelecimento comercial
ou
e/ou baterias
rede de assistência técnica
autorizada.
SAFETY INSTRUCTIONS
Restriction on Hazardous Substances statement (India)
This product complies with the “India E-waste Rule 2016” and prohibits use of lead, mercury,
hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions
set in Schedule 2 of the Rule.
E-Waste Declaration for India
This symbol on the product or on its packaging indicates that this product must not
be disposed of with your other household waste. Instead it is your responsibility to
dispose of your waste equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment . The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human
health and the environ-ment.
Batteries
For EU: The crossed-out wheeled bin implies that used batteries should not be put
to the general household waste! There is a separate collection system for used
batteries, to allow proper treatment and recycling in accordance with legislation.
Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method
of disposal of the used battery.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall
be separated to collect by local service.
8
RS232 Cable
CHAPTER 1: UNPACKING AND INSTALLATION
1.1. Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package content:
• LCD display
• User manual
• Remote control with AAA
batteries
• Power cord (1.8 m)
• VGA cable (1.8 m)
• RS232 cable (3 m)
• Daisy Chain cable (3 m)
* The supplied power cord varies depending on destination.
User Manual
SOURCE
NORMAL
ID
FORMAT
INFOLIST
OPTIONSADJUST
VOL
ID SET ENTER
Power Cord
Video Signal Cable
(D-SUB to D-SUB Cable)
Daisy Chain Cable
Remote Control
and AAA Batteries
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket
and has been approved by and complies with the safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
1.3. Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If
an extended line is required, please consult your service agent.
• The product should be installed on a at surface to avoid tipping. The distance between the
back of the product and the wall should be maintained for proper ventilation. Avoid installing the
product in the kitchen, bathroom or any other places with high humidity so as not to shorten the
service life of the electronic components.
• The product can normally operate only under 5000m in altitude. In installations at altitudes
above 5000m, some abnormalities may be experienced.
9
UNPACKING AND INSTALLATION
1.4. Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially
available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678
standard in North America.
Eye bolt
VESA Grid
Protective Sheet
Carrying handleTable
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged,
beneath the screen surface so it will not scratch the screen face.
2. Ensure you have all the accessories for mounting this display (wall mount, ceiling mount, table
stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting
procedures could result in damage to the equipment or injury to the user or installer. Product
warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M8 mounting screws (having a length 15 mm longer than the
thickness of the mounting bracket) and tighten them securely.
5. The eye bolt is using for short-time maintenance and installation. We suggest not to use the
eye bolt for more than 1 hour. Prolong the usage is prohibited. Please keep a clear safety area
under the display while using the eye bolt.
6. Mount the display on the wall when installating or maintaining the display only. It is not
recommanded to mount the display on the wall over one hour. It might cause damage on the
display when mounting the display for a long time. When mounting the display, clear all other
items under the display.
。
1.4.1. VESA Grid
Model NameVesa Grid
QD-84
QD-98
600(H) x 500(V) mm
800(H) x 500(V) mm
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend installing the display with metal brackets which
are commercially available. For detailed installation instructions, refer to the guide received with
the respective bracket.
10
UNPACKING AND INSTALLATION
• To lessen the probability of injury and damage of the display from earthquake or other natural
disaster, be sure to consult the bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the diagram
below.
100 mm
100 mm100 mm
100 mm
1.5. Using of remote sensor and power indicator
This display can be installed in portrait position.
When facing the display at the back, rotate 90 degrees anticlockwise, the input/output terminals
should at the top and right side.
90
NOTES: When installing the display on a wall, please consult a professional technician
for proper installation. We accept no liability for installations not performed by a
professional technician.
90
11
CHAPTER 2: PARTS AND FUNCTIONS
2.1. Control Panel
9
MUTE INPUT
1 23 456 78
1
[ ] button
Use this button to turn the display on or put
the display to standby.
2
[MUTE] button
Switch the audio mute ON/OFF.
3
[INPUT] button
Use this button to select the input source.
4
[ ] button
Increase the adjustment while OSD menu is
on, or increase the audio output level while
OSD menu is off.
• Used as [
] button in the On-Screen-
Display menu.
5
[ ] button
Decrease the adjustment while OSD menu is
on, or decrease the audio output level while
OSD menu is off.
6
[ ] button
Move the highlight bar up to adjust the
selected item while OSD menu is on.
MENU
9
Remote control sensor and power status
indicator
• Receives command signals from the
remote control.
• Indicates the operating status of the
display:
-Lights green when the display is turned
on.
-Lights red when the display is in standby
mode.
-Lights amber when the display enters
power save mode or deep sleep mode.
-When {SCHEDULE} is enabled, the light
blinks green and red.
-If the light blinks red, it indicates that a
failure has been detected.
-Lights off when the main power of the
display is turned off.
• Push up to hide the remote control sensor
and power stauts indicator:
7
[ ] button
Move the highlight bar down to adjust the
selected item while OSD menu is on.
8
[MENU] button
Return to previous menu while OSD menu is
on, or to activate the OSD menu when OSD
menu is off.
12
PARTS AND FUNCTIONS
2.2. Input/Output Terminals
22
21
20
19
18
17
16
15
14
13
12
11
10
9
132
1
AC IN
AC power input from the wall outlet.
2
MAIN POWER SWITCH
Switch the main power on/off.
3
HDMI1 IN / HDMI2 IN / HDMI3 IN
HDMI video/audio input.
4
RS232C IN / 5 RS232C OUT
RS232C network input / output for the loopthrough function.
6
DVI IN
DVI-D video input.
7
DisplayPort IN / 8 DisplayPort OUT
DisplayPort video input / output.
9
VGA IN (D-Sub)
VGA video input.
10
IR IN / 11 IR OUT
IR signal input / output for the loop-through
function.
NOTE:
• This display’s remote control sensor
will stop working if the jack [IR IN] is
connected.
• To remotely control your A/V device via
this display, refer to page for IR Pass
Through connection.
5
4
12
6
SPDIF OUT
8
7
Digital audio output
13
AUDIO IN
Audio input for VGA source (3.5mm stereo
phone).
14
AUDIO OUT
Audio output to external AV device.
15
SPEAKER SWITCH
Internal speaker on/off switch.
16
SPEAKERS OUT
Audio output to external speakers.
17
USB SERVICE PORT
Connect to USB storage for main board
Firmware update.
NOTE: It’s for updating rmware only.
18
RJ-45
LAN control function for the use of remote
control signal from control center.
19
Y/CVBS
Video source input.
20
COMPONENT IN
Component YPbPr video source input.
21
AUDIO IN
Audio input from external AV device (RCA).
22
USB PORT
Connect your USB storage device
13
PARTS AND FUNCTIONS
2.3. Remote Control
2.3.1 General functions
1
NORMAL
ID
2
SOURCE
3
4
5
6
7
8
9
ID SETENTER
FORMAT
INFOLIST
OPTIONSADJUST
VOL
10
11
12
13
14
15
16
17
18
1
[ ] POWER button
Turn the display on or put the display to standby.
2
[PLAY] buttons
Control playback of media les.
3
[] SOURCE button
Choose input source. Press [
] or [ ] button to choose
from DisplayPort, DVI-D, VGA. HDMI 1, HDMI 2,
HDMI 3, Component, Video, USB or Card OPS.
Press [] button to conrm and exit.
4
[] HOME button
Access the OSD menu.
5
[] LIST button
No function.
6
[ ] [ ] [ ] [ ] NAVIGATION buttons
Navigate through menus and choose items.
7
[ ] ADJUST button
To auto adjust for VGA input only.
8
[] MUTE button
Press to turn the mute function on/off.
9
[] [] [] [] COLOR buttons
Choose tasks or options.
10
[NORMAL] buttons
Switch to normal mode.
11
[ID] buttons
Switch to ID mode.
12
[] FORMAT button
Change zoom mode.
13
[] BACK button
Return to the previous menu page or exit from the
previous function.
14
[] INFO button
Display information about current activity.
15
[] button
Conrm an entry or selection.
16
[ ] OPTIONS button
Access currently available options, picture and
sound menus.
17
[ ] [ ] VOLUME button
Adjust volume.
18
[NUMERIC] buttons
Enter text for network setting, and set up ID for ID
mode.
14
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.