Agio International Sling Swivel-Rocker User Manual
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Step 1: Identify all parts packed in carton against the parts list. Remove all protective materials.
Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are
unsure as how to proceed with the assembly, call our Customer Service Center at
1-800-416-3511. Do not attempt assembly if any parts are missing or damaged.
Step 2: Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the rocker
assembly is positioned all the way into the base. It may have shifted or vibrated out during
shipment.
Step 3: Important: We recommend 2 people work together to assemble the chair. Note the
arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the
rocker plate. Point the open end of the horseshoe away from you. The arrows on the rocker
assembly should be pointing towards you. Set the chair frame on the rocker assembly with
front of the seat facing you and the arrows on the "U" bar pointing towards you as shown
in Figure 1. This is very important for a safe, balanced rocking motion. If chair frame has
been properly positioned on the rocker assembly, all arrows on the "U" bar and rocker
assembly will be pointing in the same direction.
Step 4: Critical Step: The "U" metal plates must be installed in the proper location. Read this
step and carefully examine. Insert the "U" metal plate, so that the "U" bar and rocker plate
are between both sides of the "U" metal plate. Make sure that the holes in the "U" metal
plate are completely aligned with the holes in the "U" bar as shown in Figure 1. Guide the
bolts through the holes on the top side of the "U" metal plate, through the holes in the
"U" bar portion of the chair, through the holes in the rocker plate and then, most importantly,
through the holes in the bottom side of the "U" metal plate. It is very important that the
holes in the bottom portion of the "U" metal plate be placed directly beneath the holes in the
rocker plate. Add a spring washer and a nut to each bolt as shown in Figure 2. Hand
tighten nuts 3-4 revolutions only. Repeat the same procedure on the other side.
CAUTION: Failure to place "U" metal plates under the rocker plates and above the
"U" bar exactly as shown in diagram will cause the bolt heads and nuts to damage the
structure of the rocker plates and the "U" bar. Damage due to over tightening of bolts
or improper assembly could cause injury and may void your warranty.
Step 5: Tighten all nuts and bolts with the hex wrenches provided. Do not over tighten. Remove
arrow labels from "U" bar and rocker assembly. Cover bolts with PVC bolt covers.
Step 6: Your chair should be ready for use. If your chair is not rocking properly, double-check your
assembly procedure, especially Step 3. If the chair rocks too far forward to or is difficult to
rock backwards, you have probably installed the seat frame backwards on the rocker
assembly. If you need further assistance, please call our Customer Service Center
at 1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or
improper assembly is not covered under our warranty. Please read all instructions carefully
before assembly. If you have any questions regarding your assembly, call our Customer
Service Center at 1-800-416-3511.
50-49661-1
NOTE: MAKE SURE ARROWS
FROM BOTH THE "U" BAR
AND ROCKER ASSEMBLY
ARE POINTING IN THE
SAME DIRECTION!
SWIVEL BASE
FOOT CAP
PARTS LIST DESCRIPTION ORDER PART #
CHAIR FRAME
SWIVEL BASE &
ROCKER
ASSEMBLY
5/16" X 40 MM
BOLT
E8.0 X 2.3 MM
SPRING WASHER
"U" METAL
PLATE
5/16" NUT
AR1094
AR1095
HW0295
HW0003
HW0296
HW0015
Page 2
PVC BOLT
COVER
QTY
1
1
4
4
2
4
SEAT DESIGNS MAY
VARY BUT THE ASSEMBLY
IS THE SAME
"U" METAL
PLATE
F
R
O
N
T
Figure 1
F
R
O
N
T
ROCKER
ASSEMBLY
Figure 2
PARTS LIST DESCRIPTION ORDER PART #
PVC BOLT COVER
HEX WRENCH-1
HEX WRENCH-2
FRP
FACTORY ASSEMBLY
FOOT CAP
FACTORY ASSEMBLY
SLING TUBE CAP
FACTORY ASSEMBLY
"U" BAR
FRP
PVC BOLT
COVER
BOLT
"U" BAR
SPRING
WASHER
NUT
HW0028
HW0008
HW0007
G0009
FC0004
FC0046
QTY
8
1
1
Loading...