Agio International 92558 User Manual
MULTI-PURPOSE WORK BENCH ASSEMBLY INSTRUCTIONS
#92558
DESCRIPTION ORDER PART #
A
M10 X 55MM BOLT
B
M6 X 50MM BOLT
M6 X 16MM BOLT
C
D
E
F
G
H
I
J
K
L
M6 NUT
6MM WASHER
10MM WASHER
12MM WASHER
10MM END CLIP
12MM END CLIP
10MM PVC COVER
12MM PVC COVER
M6 PVC NUT COVER
QTY
3
6
16
12
6
5
4
2
4
2
2
4
DESCRIPTION ORDER PART #
LARGE WHEEL
N
WHEEL COVER
O
AXLE SLEEVE
P
RIGHT SUPPORT
Q
R
S
T
U
V
W
X
Y
FRAME
LEFT SUPPORT
FRAME
CUSHION
HANDLE GRIP
CASTERS
FRONT SUPPORT
BAR
REAR SUPPORT
BAR
MIDDLE SUPPORT
FRAME
FRONT PANEL
COILED SHELF
WB0002
WB0003
WB0004
WB0005
WB0006
WB0007
WB0008
WB0009
WB0010
WB0011
WB0012
WB0013
QTY
4
3
1
1
2
1
1
1
1
1
DESCRIPTION ORDER PART #
2
1
DRAIN PLUG
AA
DOWEL RODS
BB
REAR FAUCET
CC
DD
EE
FF
GG
HH
I I
JJ
PANEL
FOLDING
COUNTER
AXLE FOR
FOLDING COUNTER
DRAWER
BOTTOM TRAY
“S” HOOKS
FAUCET
FOLDING COUNTER
HINGE
WB0015
WB0016
WB0017
WB0018
WB0019
WB0020
WB0021
WB0022
WB0023
WB0024
QTY
1
3
1
1
1
1
2
6
1
2
TOOLS REQUIRED FOR ASSEMBLY
Hex Wrench
Hex Bolt Driver
M
WHEEL AXLE
WB0001 WB0014
1
Z
SINK TOP BASIN
1
STEP 1
identify all parts packed in carton against the parts list. Remove all protective materials. Place parts
on a non-arasive surface to avoid scratching. If you are missing any parts or are unsure how to
proceed with assembly, call our Customer Service Center at 1-800-416-3511 (Mon - Fri 9a-5p
EST). Do not attempt assembly if any parts are missing or damaged.
Read entire assembly instructions before beginning assembly.
Figure 1
STEP 2 WHEEL ASSEMBLY
Insert wheel axle (M) through bottom shaft of right side support frame
(Q).so that it is centered inside the shaft with equal amount of axle on
each side. Snap 12mm end clip (I) on notch in axle closest to the right
side support frame (Q). Add the following parts to the axle in this order:
12mm washer (G), wheel cover (O), axle sleeve (P), wheel (N), wheel
cover (O), 12mm washer (Q), 12mm end clip (I) as shown in figure 1. Be
sure the wheel is inserted over the axle sleeve in a manner that allows it
to rotate freely. Secure the wheel assembly on the axle with the 12mm
washer clip (I). Repeat procedure for opposite side wheel.
STEP 3 LEFT SIDE SUPPORT FRAME ASSEMBLY
Screw in the two casters (T) into the bottom of the left side support frame (R) as
shown in figure 2. Add the cushion handle grip (S) to the left side support frame
(R) as shown in figure 2. Insert two M6 x 50mm bolts (B) through end of cushion
grip handle and through the holes in the left side support frame. Add a 6mm
washer (E), 6mm nut (D). Tighten with wrench. Do not over tighten. Add M6 PVC
cover to the end of each nut. Repeat on opposite side of cushion grip handle.
Figure 2
PAGE 1
STEP 4 FRAME ASSEMBLY
Connect right side support frame (Q) and left side support frame (R)
using the rear support bar (V). Be sure that the hole in the center of the
rear support bar is facing up. Add a 10mm washer (F) to a M10 x 55
mm bolt (A) and insert through the left side frame support(r) into the
fixed nuts in the rear support bar (V) as shown in figure 3. Repeat for
opposite side. (Q). Attach front support bar to middle support frame as
shown in figure 3 using a M6 x 16mm bolt. Tighten with wrench. Do
not over tighten. With bottom of rear portion of middle support frame
resting on the rear support bar, attach front support bar to right side
support frame (with wheels) using M6x 16mm bolt (C) as shown in
figure 3. Tighten with wrench. Do not over tighten. Attach middle
support frame (W) to the rear support bar (V). Align middle support bar
with hole in rear support bar as shown in figure 4. Add a 10mm washer
(F) to an M10 x 55mm bolt (A). Insert bolt through middle support
frame and into the fixed nut inside the rear support bar.
Figure 3
STEP 5 COILED SHELF ASSEMBLY
Attach coiled shelf (Y) to right side support frame (Q) and middle
support frame (W) using M6 x 16 bolts (C) as shown in figure 4.
Position coiled shelf between the right side and middle support frames
so that coiled portion of the panel is acing towards the bottom. Insert
bolts through the holes from behind the coiled shelf and into the fixed
nuts inside the right side and middle support frames. Use hex wrench
to tighten completely. Do not over tighten. Attach front panel to left
side and middle support panels as shown if figure 4 using M6 x 16mm
bolts (C). Insert bolts through holes from behind the front panel into the
fixed nuts in the front portion of the left side and middle support
frames. Tighten using hex wrench. Do not over tighten.
STEP 6 SINK ASSEMBLY
Install sink drain/stopper assembly (AA) as shown in figure 5.
Separate the three pieces and insert the center gasket into the whole
in the sink basin. Insert the funnel-shaped portion into the sink drain
as shown. From underneath the sink basin, attach the bottom portion
of the sink drain/stopper assembly onto the bottom portion of the
funnel shaped piece to hold firmly in place.
Figure 4
Figure 5
PAGE 2
Loading...