Agilent 6N139, 6N138, HCPL-0701, HCPL-0700, HCNW139 User Guide

...

Low Input Current, High Gain Optocouplers

Technical Data

6N139 6N138 HCPL-0701 HCPL-0700 HCNW139 HCNW138

Features

• High Current Transfer Ratio – 2000% Typical (4500% Typical for HCNW139/138)

• Low Input Current Requirements – 0.5 mA

• TTL Compatible Output –

0.1 V VOL Typical

• Performance Guaranteed over Temperature 0°C to 70°C

• Base Access Allows Gain Bandwidth Adjustment

• High Output Current – 60 mA

• Safety Approval

UL Recognized – 3750 V rms

for 1 Minute and 5000 V rms*

for 1 Minute per UL 1577 CSA Approved IEC/EN/DIN EN 60747-5-2 Approved with V V peak for HCNW139 and HCNW138

• Available in 8-Pin DIP or SOIC-8 Footprint or Widebody Package

• MIL-PRF-38534 Hermetic Version Available (HCPL5700/1)

IORM

= 1414

Applications

• Ground Isolate Most Logic Families – TTL/TTL, CMOS/ TTL, CMOS/CMOS, LSTTL/ TTL, CMOS/LSTTL

• Low Input Current Line Receiver

• High Voltage Insulation (HCNW139/138)

• EIA RS-232C Line Receiver

• Telephone Ring Detector

• 117 V ac Line Voltage Status Indicator – Low Input Power Dissipation

• Low Power Systems – Ground Isolation

Functional Diagram

ANODE

CATHODE

GND

Description

These high gain series couplers use a Light Emitting Diode and an integrated high gain photodetector to provide extremely high current transfer ratio between input and output. Separate pins for the photodiode and output stage result in TTL compatible saturation voltages and high speed operation. Where desired the VCC and VO terminals may be tied together to achieve conventional photodarlington operation. A base access terminal allows a gain bandwidth adjustment to be made.

TRUTH TABLE

LED

ON

OFF



LOW HIGH

O



*5000 V rms/1 minute rating is for HCNW139/138 and Option 020 (6N139/138) products only. A 0.1 µF bypass capacitor connected between pins 8 and 5 is recommended.

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

The 6N139, HCPL-0701, and CNW139 are for use in CMOS, LSTTL or other low power applications. A 400% minimum current transfer ratio is guaranteed over 0 to 70°C operating range for only

0.5 mA of LED current.

(1 TTL Unit load ). A 300% minimum CTR enables operation with 1 TTL Load using a 2.2 kΩ pull-up resistor.

Selection for lower input current down to 250 µA is available upon request.

The SOIC-8 does not require “through holes” in a PCB. This package occupies approximately one-third the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface

mount processes. The 6N138, HCPL-0700, and HCNW138 are designed for use mainly in TTL applications. Current Transfer Ratio (CTR) is 300% minimum over 0 to 70°C for an LED current of 1.6 mA

The HCPL-0701 and HCPL-0700 are surface mount devices packaged in an industry standard SOIC-8 footprint.

The HCNW139 and HCNW138

are packaged in a widebody

encapsulation that provides creep-

age and clearance dimensions

suitable for safety approval by

regulatory agencies worldwide.

Selection Guide

Widebody

8-Pin DIP Package Hermetic

(300 Mil) Small Outline SO-8 (400 mil) Single and

Dual Single Dual Minimum Absolute Dual

Single Channel Channel Channel Single Input ON Maxi- Channel Channel Package Package Package Channel Current Minimum mum Packages Package HCPL- HCPL- HCPL- Package (I

4731

[1]

0701 0731 HCNW139 0.5 mA 400% 18 V 0700 0730 HCNW138 1.6 mA 300% 7 V

070A

[1]

073A

[1]

6N139 2731

6N138 2730

HCPL-4701

[1]

) CTR V

40 µA 800% 18 V

0.5 mA 300% 20 V 5701

HCPL-

[1] [1]

5700

[1]

5731

[1]

5730

Note:

1. Technical data are on separate Agilent publications.

Ordering Information

Specify Part Number followed by Option Number (if desired).

Example:

6N139#XXXX

020 = 5000 V rms/1 Minute UL Rating Option* 300 = Gull Wing Surface Mount Option† 500 = Tape and Reel Packaging Option XXXE = Lead Free Option

Option data sheets available. Contact your Agilent sales representative or authorized distributor for information.

*For 6N139 and 6N138 only. †Gull wing surface mount option applies to through hole parts only.

Remarks: The notation “#” is used for existing products, while (new) products launched since 15th July 2001 and lead free option will use “-”

Schematic

ANODE

CATHODE

– 3

GND

SHIELD

Package Outline Drawings

8-Pin DIP Package (6N139/6N138)**

7.62 ± 0.25

(0.300 ± 0.010)

6.35 ± 0.25

(0.250 ± 0.010)

5° TYP.

0.254

(0.010

TYPE NUMBER

1.19 (0.047) MAX.

3.56 ± 0.13

(0.140 ± 0.005)

1.080 ± 0.320

(0.043 ± 0.013)

9.65 ± 0.25

(0.380 ± 0.010)

A XXXXZ



YYWW

5678

OPTION CODE* DATE CODE

UL

4321

RECOGNITION

1.78 (0.070) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

0.65 (0.025) MAX.

2.54 ± 0.25

(0.100 ± 0.010)

0.51 (0.020) MIN.

DIMENSIONS IN MILLIMETERS AND (INCHES). * MARKING CODE LETTER FOR OPTION NUMBERS

"L" = OPTION 020 OPTION NUMBERS 300 AND 500 NOT MARKED.  NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

**JEDEC Registered Data.

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N139/6N138)

+ 0.076

- 0.051

+ 0.003)

- 0.002)

1.19

(0.047)

MAX.

1.080 ± 0.320

(0.043 ± 0.013)

LAND PATTERN RECOMMENDATION

9.65 ± 0.25

(0.380 ± 0.010)

2.54

(0.100)

BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

6.350 ± 0.25

(0.250 ± 0.010)

1.27 (0.050)

1.780

(0.070)

MAX.

3.56 ± 0.13

(0.140 ± 0.005)

0.635 ± 0.130

(0.025 ± 0.005)

(0.380 ± 0.010)

(0.300 ± 0.010)

0.635 ± 0.25

(0.025 ± 0.010)

1.016 (0.040)

9.65 ± 0.25

7.62 ± 0.25

10.9 (0.430)

2.0 (0.080)

0.254

(0.010

12° NOM.

+ 0.076

- 0.051

+ 0.003)

- 0.002)

Small Outline SO-8 Package (HCPL-0701/HCPL-0700)

8765

3.937 ± 0.127

(0.155 ± 0.005)

PIN ONE

0.406 ± 0.076

(0.016 ± 0.003)

3.175 ± 0.127

(0.125 ± 0.005)

TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)

5.207 ± 0.254 (0.205 ± 0.010)  DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 

NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.

XXX

YWW

5.080 ± 0.127

(0.200 ± 0.005)

4321

1.270

(0.050)

5.994 ± 0.203

(0.236 ± 0.008)

TYPE NUMBER (LAST 3 DIGITS)

DATE CODE

BSC

1.524

(0.060)

7°

0 ~ 7°

LAND PATTERN RECOMMENDATION

0.64 (0.025)

0.432

45° X

(0.017)

(0.009 ± 0.001)

0.203 ± 0.102

(0.008 ± 0.004)

0.305

MIN.

(0.012)

7.49 (0.295)

1.9 (0.075)

0.228 ± 0.025

8-Pin Widebody DIP Package (HCNW139/HCNW138)

11.15 ± 0.15

(0.442 ± 0.006)

TYPE NUMBER DATE CODE



1.55

(0.061)

MAX.

3.10 (0.122)

3.90 (0.154)

0.40 (0.016)

0.56 (0.022)

2.54 (0.100) TYP.

1.78 ± 0.15

(0.070 ± 0.006)

HCNWXXXX

A 

YYWW

11.00

MAX.

(0.433)

9.00 ± 0.15

(0.354 ± 0.006)

10.16 (0.400) TYP.

7° TYP.

5.10

MAX.

(0.201)

0.51 (0.021) MIN.

DIMENSIONS IN MILLIMETERS (INCHES).  NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254

(0.010

+ 0.076

- 0.0051 + 0.003)

- 0.002)

+ 11 hidden pages