Agilent E8267C Data Sheet

Page 1

Agilent E8267C PSG Vector Signal Generators

Data Sheet

All specifications and characteristics apply over a 0 to 55 °C range (unless otherwise stated) and apply after a 45 minute warm-up time. Supplemental characteristics, denoted as typical or nominal, provide additional (non-warranted) information.

Definitions

Specifications (spec): represent warranted performance.

Typical (typ): performance is not warranted. It applies at 25 °C. A minimum of 80% of all

products meet typical performance.

Nominal (nom): values are not warranted. They represent the value of a parameter that is most likely to occur; the expected or mean value. They are included to facilitate the application of the product.

Standard (std): No options are included when referring to the signal generator unless noted otherwise.

PSG Signal Generators

Option 520 Option 540

250 kHz to 20 GHz 250 kHz to 40 GHz

CW only E8247C E8247C Analog E8257C E8257C Vector E8267C

(See E8247C/E8257C data sheet for PSG CW and Analog Signal Generator specifications)

Page 2

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Digital sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Ramp (analog) sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Spectral purity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Frequency modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Phase modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Amplitude modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Wideband AM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

External modulation inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Simultaneous modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Internal modulation source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Pulse modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Internal pulse generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Vector modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

I/Q baseband generator: arbitrary waveform mode . . . . . . . . . . . . . . . . .15

I/Q baseband generator: real-time mode . . . . . . . . . . . . . . . . . . . . . . . . .17

Wideband external I/Q inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Remote programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Input/Output Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Front panel connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Rear panel connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Auxiliary I/O connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Options, Accessories, and Related Products . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Web Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Related Agilent Literature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Table of Contents

Page 3

Range

Option 520 250 kHz to 20 GHz

Resolution

CW 0.001 Hz All Sweep Modes 0.01 Hz

Accuracy Aging rate ± temperature effects± line voltage effects Switching speed

< 12 ms (typical)

Phase offset Adjustable in nominal 0.1° increments. Frequency bands

Band Frequency range N #

1 250 kHz to 250 MHz 1/8 2 > 250 to 500 MHz 1/16 3 > 500 MHz to 1 GHz 1/8 4 > 1 to 2 GHz 1/4 5 > 2 to 3.2 GHz 1/2 6 > 3.2 to 10 GHz 1 7 > 10 to 20 GHz 2

Internal timebase reference oscillator

Standard Option UNR

Aging rate < ±1 x 10

-7

/year or < ±3 x10-8/year or

< ±4.5 x 10

-9

/day < ±2.5 x 10

-10

/day

after 45 days after 30 days

Temperature effects (typical) < ±5 x 10-80 to 55 °C < ±4.5 x 10-90 to 55 °C Line voltage effects (typical) < ±2 x 10-9for < ±2 x 10

-10

for

+5% –10% change ±10% change

External reference frequency 1, 2, 2.5, 5, 10 MHz 10 MHz only Lock Range ±0.2 ppm ±1.0 ppm

Reference output

Frequency 10 MHz Amplitude > +4 dBm into 50 Ω load (typical)

External reference input

Amplitude > -3 dBm Option UNR 5 dBm ±5 dB

Input impedance 50 Ω (nominal)

Specifications

Frequency

1. Useable, but unspecified, down to 100 kHz

2. In ramp sweep mode (Option 007), resolution is limited with narrow spans and slow sweep speeds. Refer to ramp sweep specifications for more information.

3. To within 0.1 ppm of final frequency above 250 MHz or within 100 Hz below 250 MHz

4. To optimize phase noise 5 dBm ± 2 dB

Page 4

Operating modes Step sweep of frequency or amplitude or both (start to stop)

List sweep of frequency or amplitude or both (arbitrary list)

Sweep range

Frequency sweep Within instrument frequency range Amplitude sweep Within attenuator hold range

Dwell time 1 ms to 60 s Number of points 2 to 65535 (step sweep)

2 to 1601 per table (list sweep)

Triggering Auto, external, single, or GPIB

Operating modes Synthesized frequency sweep

(start/stop), (center/span), (swept CW) Power (amplitude) sweep (start/stop) Manual sweep RPG control between start and stop frequencies Alternate sweep Alternates successive sweeps between current and stored states

Sweep span range Settable from minimum2to full range Maximum sweep rate Start Maximum Max span for

frequency sweep rate 100 ms sweep

250 kHz to <0.5 GHz 25 MHz/ms 2.5 GHz

0.5 to <1 GHz 50 MHz/ms 5 GHz 1 to <2 GHz 100 MHz/ms 10 GHz 2 to <3.2 GHz 200 MHz/ms 20 GHz ≥3.2 GHz 400 MHz/ms 20 GHz

Frequency accuracy ± 0.05% of span ± timebase (at 100 ms sweep time, for

sweep spans less than maximum values given above) Accuracy improves proportionally as sweep time increases

Sweep time (forward sweep, not including bandswitch and retrace intervals) Resolution 1 ms Manual mode Settable 10 ms to 99 seconds Auto mode Set to minimum value determined by maximum sweep rate

and 8757D setting

Triggering Auto, external, single, or GPIB Markers 10 independent continuously variable frequency markers

Display Z-axis intensity or RF amplitude pulse Functions M1 to center, M1/M2 to start/stop, marker delta

Two-tone (master/slave)

measurements

Two PSGs can synchronously track each other, with independent control of start/stop frequencies

Network analyzer compatibility Fully compatible with Agilent 8757D scalar network analyzer

Also useable with Agilent 8757A/C/E scalar network analyzers for making basic swept measurements.

Ramp (analog) sweep

(Option 007)

Digital sweep

1. During Ramp sweep operation, AM and Pulse Modulation are useable but not specified; FM, Phase Modulation, Wideband AM and I/Q modulation are not useable.

2. Minimum settable sweep span is proportional to carrier frequency and sweep time. Actual sweep span may be slightly different than desired setting for spans less than [0.00004% of carrier frequency or 140 Hz] x [sweep time in seconds]. Actual span will always be displayed correctly.

3. Typical accuracy for sweep times > 100 ms can be calculated from the equation: [(0.005% of span)/(sweep time in seconds)] ± timebase. Accuracy is not specified for sweep times < 100 ms.

4. For Master/Slave operation use Agilent Technologies part #8120-8806 Master/Slave interface cable.

5. When measuring low-pass devices in AC mode, dynamic range may be reduced up to 10dB below 3.2 GHz

6. GPIB system interface is not supported with 8757A/C/E, only with 8757D. As a result, some features of the 8757A/C/E, such as frequency display, pass-through mode, and alternate sweep, do not function with PSG signal generators.

Page 5

Output

Power1(dBm) Frequency range

250 kHz to 3.2 GHz

–130 to +13

250 kHz to 3.2 GHz (with Option 1E6)

–130 to +10

> 3.2 to 20 GHz

–130 to +18

Step attenuator from 0 to 115 dB in 5 dB steps

Measured maximum available power in CW mode

Attenuator hold range (Same as max power sweep range) Minimum From –15 dBm to maximum specified output

power with step attenuator in 0 dB position. Can be offset using step attenuator.

Amplitude switching speed

CW or analog modulation < 5 ms (typical) When using power search < 25 ms (typical)

Level accuracy6(dB) Frequency

> +10 dBm +10 to –10 dBm –10 to –70 dBm –70 to –90 dBm –90 to –110 dBm

250 kHz to 2 GHz

±0.6 ±0.6 ±0.7 ±0.8 ±1.4

> 2 to 20 GHz ±0.8 ±0.8 ±0.9 ±1.0 ±1.7 CW Level accuracy with I/Q modulation (With PRBS modulated data) (relative to CW)

With ALC On:

QAM or QPSK formats

±0.2 dB

Constant-amplitude formats (FSK, GMSK, etc) ± 0.2 dB

With ALC Off:

± 0.2 dB (typical)

1. Maximum power specification is warranted from 15 to 35 ºC, and is typical from 0 to 15 ºC. Maximum power over the 35 to 55 ºC range typically degrades less than 2 dB

2. With I/Q modulation on, maximum power specification is typical. With external inputs enabled,

(I2+ Q2) > 0.2 V

rms

3. With I/Q modulation on, maximum power specification is typically +15 dBm. With external inputs enabled,

(I2+ Q2) > 0.2 V

rms

4. The step attenuator provides coarse power attenuation to achieve low power levels. Fine power level adjustment is provided by the ALC (Automatic Level Control) within the attenuator hold range.

5. To within 0.1 dB of final amplitude within one attenuator range

6. Specifications apply in CW and list/step sweep modes over the 15 to 35 ºC temperature range, with attenuator hold off (normal operating mode). Degradation outside this range, for ALC power levels > –5 dBm, is typically < 0.3 dB. In Ramp sweep mode (with Option 007), specifications are typical. For instruments with Type-N connectors (Option 1ED), specifications are degraded typically 0.2 dB above 18 GHz. Level accuracy is not specified below –110 dBm.

7. If external inputs are used, specification applies with input level (I2+ Q2) = 0.3 V

rms

and I/Q modulator

attenuation = 10 dB.

8. Measured with symbol rate > 10 kHz and power ≤ 0 dBm.

9. Relative to ALC on, after power search is executed. When applying external I/Q signals with ALC off, output level will vary directly with I/Q input level.

E8267C model

Frequency (MHz)

0 5000 10000 15000 20000

Page 6

20 GHz level accuracy

Resolution 0.01 dB Temperature stability 0.01 dB/ °C (typical) User flatness correction

Number of points 2 to 1601 points/table Number of tables Up to 10,000, memory limited Path loss Arbitrary, within attenuator range Entry modes Remote power meter

, remote bus, manual

(user edit/view)

Output impedance 50 Ω (nominal) SWR (internally leveled, typical)

250 kHz to 2 GHz < 1.4:1 > 2 GHz to 20 GHz < 1.6:1 Leveling modes Internal leveling, external detector leveling,

millimeter source module, ALC Off

External detector leveling

Range –0.2 mV to –0.5 V, (nominal) (–36 dBm to +4 dBm

using Agilent 33330D/E detector)

Bandwidth 10 kHz (typical)

(Note: not intended for pulsed operation)

Maximum reverse power 1/2 Watt (nominal)

1. Compatible with Agilent Technologies EPM Series (E4418B and E4419B) power meters.

Measured level accuracy +5 dBm

Frequency (MHz)

0.5

-0.5

-1

5000

10000 15000

20000

Page 7

Harmonics

(dBc at +10 dBm or maximum specified output power,

whichever is lower) < 1 MHz –27 dBc (typical) 1 MHz to 2 GHz –27 dBc > 2 GHz to 20 GHz –55 dBc

20 GHz Measured harmonics

Sub-harmonics

(dBc at +10 dBm or maximum specified output power,

whichever is lower) 250 kHz to 10 GHz None > 10 GHz to 20 GHz < –60 dBc Non-harmonics (dBc at +10 dBm or maximum specified output power,

whichever is lower, for offsets > 3 KHz [>300 Hz with

Option UNR])

Frequency Spec Typical

250 kHz to 250 MHz –65 –72 for > 10 kHz offsets > 250 MHz to 1 GHz –80 –88 > 1 to 2 GHz –74 –82 > 2 to 3.2 GHz –68 –76 > 3.2 to 10 GHz –62 –70 > 10 to 20 GHz –56 –64

SSB phase noise (CW) Offset from carrier (dBc/Hz) Frequency 20 kHz 20 kHz (typical)

250 kHz to 250 MHz –130 –134 > 250 to 500 MHz –134

–138 > 500 MHz to 1 GHz –130 –134 > 1 to 2 GHz –124 –128 > 2 to 3.2 GHz –120 –124 > 3.2 to 10 GHz –110 –113 > 10 to 20 GHz –104 –108

Spectral purity

1. Specifications for harmonics beyond maximum instrument frequencies are typical.

2. Specifications for sub-harmonics beyond maximum instrument frequencies are typical.

3. Performance is typical for spurs at frequencies above the maximum operating frequency of the instrument. Specifications apply for CW mode only. Performance typically is –60 dBc between 200 and 250 MHz.

4. For instruments with serial number prefixes below MY4330 or US4330, the specification is –136 dBc/Hz.

Measured harmonics +10 dBm

Frequency (MHz)

Harmonics (dBc)

-30

-40

-50

-60

-70

-80

0 2000 4000 6000 8000 10000

Page 8

Option UNR: Enhanced SSB phase noise (CW)

Offset from carrier (dBc/Hz)

Frequency 100 Hz 1 kHz 10 kHz 100 kHz

spec (typical) spec (typical) spec (typical) spec (typical) 250 kHz to 250 MHz –94 (–115) –110 (–123) –128 (–132) –130 (–133) > 250 to 500 MHz –100 (–110) –124 (–130) –132 (–136) –136 (–141) > 500 MHz to 1 GHz –94 (–104) –118 (–126) –130 (–135) –130 (–135) > 1 to 2 GHz –88 (–98) –112 (–120) –124 (–129) –124 (–129) > 2 to 3.2 GHz –84 (–94) –108 (–116) –120 (–125) –120 (–125) > 3.2 to 10 GHz –74 (–84) –98 (–106) –110 (–115) –110 (–115) > 10 to 20 GHz –68 (–78) –92 (–100) –104 (–107) –104 (–109)

Residual FM

CW mode < N x 8 Hz (typical) Option UNR < N x 4 Hz (typical) Ramp sweep mode: < N x 1 kHz (typical) (rms, 50 Hz to 15 kHz bandwidth)

Broadband noise

(CW mode at +10 dBm or maximum specified output power, whichever is lower, for offsets > 10 MHz) > 2.4 to 20 GHz < –148 dBc/Hz (typical)

Measured phase noise with E5500 and plotted without spurs

1. External I/Q input level

(I2+ Q2)

= 250 mV

rms

., I/Q modulator attenuator set to auto.

Standard Phase noise Standard phase noise performance with I/Q modulation on

Option UNR Option UNR with I/Q modulation on

Page 9

Measured standard vs. Option UNR at 10 GHz Measured AM noise at 10 GHz

1. Calculated from phase noise performance in CW mode only at +3 dBm. For other frequencies, data rate, or

bandwidths, please contact your sales representative.

Typical rms jitter:

Standard

Carrier SONET/SDH rms jitter Unit intervals Time frequency data rates bandwidth (µUI) (fs)

155 MHz 155 MB/s 100 Hz to 1.5 MHz 95 497 622 MHz 622 MB/s 1 kHz to 5 MHz 54 55

2.488 GHz 2488 MB/s 5 kHz to 15 MHz 64 24

9.953 GHz 9953 MB/s 20 kHz to 80 MHz 162 16

Option UNR

Carrier SONET/SDH rms jitter Unit intervals Time frequency data rates bandwidth (µUI) (fs)

155 MHz 155 MB/s 100 Hz to 1.5 MHz 85 400 622 MHz 622 MB/s 1 kHz to 5 MHz 25 39

2.488 GHz 2488 MB/s 5 kHz to 15 MHz 61 24

9.953 GHz 9953 MB/s 20 kHz to 80 MHz 158 15

Page 10

Maximum deviation N x 8 MHz Resolution 0.1% of deviation or 1 Hz, whichever is greater Deviation accuracy < ± 3.5% of FM deviation + 20 Hz

(1 kHz rate, deviations < N x 800 kHz)

Modulation frequency response Path Rates (at 100 kHz deviation)

1 dB Bandwidth 3 dB Bandwidth (typical)

FM 1 dc/20 Hz to 100 kHz dc/5 Hz to 10 MHz FM 2 dc/20 Hz to 100 kHz dc/5 Hz to 1 MHz

dc FM1carrier offset ±0.1% of set deviation + (N x 8 Hz) Distortion < 1% (1 kHz rate, deviations < N x 800 kHz) Sensitivity ±1 V

peak

for indicated deviation

Paths FM1 and FM2 are summed internally for composite

modulation. Either path may be switched to any one of the modulation sources: Ext1, Ext2, internal1, internal2. The FM2 path is limited to a maximum rate of 1 MHz. The FM2 path must be set to a deviation less than FM1.

Maximum deviation N x 80 radians

(N x 8 radians in high-bandwidth mode)

Resolution 0.1% of set deviation Deviation accuracy < ±5% of deviation + 0.01 radians

(1 kHz rate, normal BW mode)

Modulation frequency response Mode Maximum Deviation Rates (3 dB BW)

Normal BW N x 80 rad dc – 100 kHz High BW N x 8 rad dc – 1 MHz (typical) Distortion < 1 % (1 kHz rate, THD, dev < N x 80 rad,

normal BW mode)

Sensitivity ±1 V

peak

for indicated deviation

Paths ΦM1 and ΦM2 are summed internally for composite

modulation. Either path may be switched to any one of the modulation sources: Ext1, Ext2, internal1, internal2. The ΦM2 path must be set to a deviation less than ΦM1.

Depth Linear mode Exponential (log) mode

(Downward modulation only) Maximum > 90% > 20 dB Settable

0 to 100 % 0 to 40 dB Resolution 0.1% 0.01 dB Accuracy (1 kHz rate) < ±(6 % of setting + 1 %) < ±(2% of setting + 0.2 dB) Ext sensitivity ±1 V

peak

for –1 V for indicated depth

indicated depth

Rates (3 dB bandwidth, 30% depth) dc/10 Hz to 100 kHz (typical) (useable to 1 MHz) Distortion (1 kHz rate, linear mode, THD)

30% AM < 1.5% 90% AM < 4 % Paths AM1 and AM2 are summed internally for composite

modulation. Either path may be switched to any one of the modulation sources: Ext1, Ext2, internal1, internal2.

Frequency modulation

Phase modulation

Amplitude modulation (f

> 2 MHz)2 (typical)

1. At the calibrated deviation and carrier frequency, within 5 °C of ambient temperature at time of user calibration.

2. For fc< 2 MHz AM is usable but not specified. AM specifications apply with ALC on, and envelope peaks

< maximum specified power.

3. For AM depth settings > 90% or > 20 dB, deep AM mode is recommended.

Page 11

Rate (typical 1 dB bandwidth)

ALC on 1 kHz to 80 MHz ALC off DC to 80 MHz

External 1 input

Sensitivity 0.5 V = 100% Input impedance 50 Ω (nominal)

Modulation types AM, FM, and ΦM Input impedance 50 or 600 Ω (nominal), switched High/low indicator

(100 Hz to 10 MHz BW, ac coupled inputs only) Activated when input level error exceeds 3% (nominal)

All modulation types may be simultaneously enabled except: FM with ΦM, linear AM with exponential AM, and Wideband AM with I/Q. AM, FM, and ΦM can sum simultaneous inputs from any two sources (Ext1, Ext2, internal1, or internal2) Any given source (Ext1, Ext2, internal1, or internal2) may be routed to only one activated modulation type.

Dual function generators provides two independent signals (internal1 and internal2) for use with AM, FM, ΦM, or LF Out. Waveforms Sine, square, positive ramp, negative ramp, triangle,

Gaussian noise, uniform noise, swept sine, dual sine

Rate range

Sine 0.5 Hz to 1 MHz Square, ramp, triangle 0.5 Hz to 100 kHz Resolution 0.5 Hz Accuracy Same as timebase

LF out Output Internal1 or internal2. Also provides monitoring of

internal1 or internal2 when used for AM, FM, or ΦM.

Amplitude 0 to 3 V

peak

, into 50 Ω (nominal)

Output impedance 50 Ω (nominal)

Swept sine mode:

(frequency, phase continuous) Operating modes Triggered or continuous sweeps Frequency range 1 Hz to 1 MHz Sweep rate 0.5 Hz to 100 kHz sweeps/s, equivalent to

sweep times 10 us to 2 s

Resolution 0.5 Hz (0.5 sweep/s)

Wideband AM

External modulation inputs (Ext1 & Ext2)

Simultaneous modulation

Internal modulation source

1. Internal2 is not available when using swept sine or dual sine modes.

Page 12

Standard Standard Option 1E6

> 3.2 GHz 500 MHz to 3.2 GHz 10 MHz to 3.2 GHz On/off ratio 80 dB 80 dB (typical) 80 dB Rise/fall times (Tr, Tf ) 10 ns (6 ns typical) 100 ns (typical) 10 ns (8 ns typical) Pulse width

Internally leveled ≥ 1µs ≥ 2 µs (typical) ≥ 1µs Level hold (ALC Off ≥ 20 ns (typical) ≥ 0.5 µs (typical) ≥ 20 ns (typical)

with power search)

Repetition frequency

Internally leveled 10 Hz to 500 kHz 10 Hz to 250 kHz 10 Hz to 500 kHz

(typical) (typical) (typical)

Level hold (ALC Off with dc to 10 MHz dc to 1 MHz (typical) dc to 10 MHz (typical)

power search)

(typical)

Level accuracy (relative to CW) Internally leveled ±0.5 dB ± 0.5 dB ± 0.5 dB

±0.15 (typical) Level hold (ALC Off with ≤ 20 GHz ±0.8 dB ±0.5 dB (typical) ± 1.2 dB (typical)

power search)

(typical)

Width compression ±5 ns (typical) ±50 ns (typical) ±5 ns (typical) Video feed-through4< 2 mV (typical) < 200 mV (typical) < 125 mV (typical) Video delay

(Ext input to Video) 40 ns (nominal) 40 ns (nominal) 40 ns (nominal) RF delay (Tm) (Video to RF output) 35 ns (nominal) 280 ns (nominal) 45 ns (nominal)

Pulse overshoot (Vor) < 10% (typical) < 10% (typical) < 10% (typical) Input level +1 V

peak

= RF On +1 V

peak

= RF On +1 V

peak

= RF On

Input impedance 50 Ω, (nominal) 50 Ω, (nominal) 50 Ω, (nominal)

Pulse modulation

1. With ALC off, specs apply after the execution of power search. Specs apply with Atten Hold off (default

mode), or ALC level between 0 and +10 dBm.

2. Option 1E6 provides narrow pulse (20 ns typical) capability between 10 MHz and 3.2 GHz. Narrow pulse

capability above 3.2 GHz is standard.

3. Power search is a calibration routine that improves level accuracy in ALC-off mode. Un-pulsed RF power

will be present typically up to 50 ms when executing power search.

4. With attenuator in 0 dB position. Video feed-through decreases with attenuator setting.

Measured pulse modulation envelope

Freq = 10GHz, Amp = 10dBM, ALC = OFF, Pulse width = 50ns

Timebase (nsec)

0 10 20 30 40 50 60 70 80 90 100

Page 13

Internal pulse generator

Modes Free-run, triggered, triggered with delay, doublet,

and gated. Triggered with delay, doublet, and gated require external trigger source.

Period (PRI) (Tp ) 70 ns to 42 s

(Repetition frequency: 0.024 Hz to 14.28 MHz)

Pulse width (Tw ) 10 ns to 42 s Delay (Td )

Free-run mode 0 to ±42 s Triggered with delay and doublet modes 75 ns to 42 s with ±10 ns jitter

Resolution 10 ns (width, delay, and PRI)

Sync output

Video output

RF pulse output

50%

10%

90%

50%

Td video delay (variable)

Tw video pulse width (variable)

Tp pulse period (variable)

Tm RF delay

Trf RF pulse width

Tf RF pulse fall time

Tr RF pulse rise time

Vor pulse overshoot

Vf video feedthrough

Page 14

External I/Q inputs

Input impedance switched 50 or 600 Ω (nominal) Input range

Minimum 0.1 V

rms

, maximum 1V

peak

Flatness ± 1 dB within ± 40 MHz of carrier (with ALC off) (typical)

Measured I/Q frequency response

I/Q adjustments

I & Q offsets External inputs (600 Ω) ± 5 Volts

External inputs (50 Ω) ± 50 %

Internal baseband generator ± 50 % I/Q attenuation 0 to 40 dB I/Q gain balance ± 4 dB I/Q quadrature skew ± 10° range (typical) Low pass filter Selectable 40 MHz or through

I/Q baseband outputs

Differential I, I bar, Q, Q bar Single ended I, Q Frequency range DC to 40 MHz Output voltage into 50 W 1.5 V

p-p

(typical) DC offset adjustments ± 3 V DC offset resolution 1 mV Low pass filter Selectable 40 MHz or though

Vector modulation

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.15 -0.10 -0.05 0.00 0.05 0.10 0.15

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.15 -0.10 -0.05 0.00 0.05 0.10 0.15

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.15 -0.10 -0.05 0.00 0.05 0.10 0.15

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.15 -0.10 -0.05 0.00 0.05 0.10 0.15

1.5 GHz 3 GHz

12 GHz 20 GHz

1. For optimum signal quality, the I and Q inputs should be 0.7 V

peak

, with (I2+ Q2) + 150 mV

rms

. Different RMS levels are accommodated by adjusting the internal I/Q modulator attenuator, which may be either manually or automatically set. The minimum input level required to maintain RF level accuracy is

(I2+ Q2) = 0.1 V

rms

2. Sine wave response, measured with input level = 100 mV

rms

on one channel, and ALC off.

Page 15

Channels 2 [I and Q] Resolution 16 bits [1/65,536] Baseband waveform memory

Length (playback) 64 megasamples (MSa) Length (storage) 1.2 gigasamples (GSa) on 6 GB hard drive (Option 005)

Waveform segments

Segment length 60 samples to 64 MSa Maximum number of segments 8192 Minimum memory allocation 256 samples or 1 kbyte blocks

Waveform sequences

Sequencing Continuously repeating Maximum number of sequences 16,384 Maximum segments/sequence 1 to 32,768 Maximum segment repetitions 1 to 65,536

Clock

Sample rate 1 Hz to 100 MHz Resolution 0.001 Hz Accuracy Same as timebase +2

-42

[in non-integer applications]

Reconstruction filter: [fixed] 50 MHz [used for all symbol rates] Baseband spectral purity

[full scale sinewave] Harmonic distortion 100 kHz to 2 MHz: < –65 dBc (typical) Phase noise < –127 dBc/Hz (typical)

(baseband output of 10 MHz sinewave at 20 kHz offset)

IM performance < –74 dB (typical)

(two sinewaves at 950 kHz and 1050 kHz at baseband)

Triggers

Types Continuous, single, gated, segment advance Source Trigger key, external, remote [LAN, GPIB, RS-232] External polarity Negative, positive External delay time 10 ns to 40 sec plus latency External delay resolution 10 ns

Markers

(Markers are defined in a segment during the waveform generation process, or from the PSG front panel. A marker can also be tied to the RF blanking feature of the PSG.)

Marker polarity Negative, positive Number of markers 4

Multicarrier

Number of carriers Up to 100 (limited by a max bandwidth of 80 MHz

depending on symbol rate and modulation type) Frequency offset (per carrier) –40 MHz to +40 MHz Power offset (per carrier) 0 dB to –40 dB

Modulation

PSK BPSK, QPSK, OQPSK, π/4DQPSK, 8PSK,16PSK, D8PSK QAM 4, 16, 32, 64, 256 FSK Selectable: 2, 4, 8, 16 MSK Data Random ONLY

I/Q baseband generator: arbitrary waveform mode

(Option 602)

Page 16

Measured multicarrier

4 Carriers with 64 QAM at 10 Msym\s with 20 MHz spacing

Multitone

Number of tones 2 to 64, with selectable on/off state per tone Frequency spacing 100 Hz to 80 MHz Phase (per tone) Fixed or random Power offset (per tone) 0 to –40 dB

Ref-4 dBm Samp Log 10 dB/

LgAv 10 W1 S2 S3 FC

(f): #f>50K #Swp

#Atten 6 dB

Center 20.000 00 GHz Res BW 1.8 MHz

VBW 1.8 MHz

Span 200 MHz

Sweep 1 ms

Ref 0 dBm Norm Log 10 dB/

LgAv

W1 S2 S3 FC

(f): #f>50K #Swp

Atten 10 dB

Mkr1 -38.67 MHz

-41.19 dB

Center 20.000 00 GHz #Res BW 3 kHz

VBW 3 kHz

Span 80 MHz

Sweep 10.72 s

Marker

-38.670000 MHz

-41.19 dB

Ref-4 dBm Samp Log 10 dB/

LgAv 10 W1 S2 S3 FC

(f): #f>50K #Swp

#Atten 6 dB

Mkr1 -8.00 MHz

-59.104 dB

Center 20.000 00 GHz Res BW 180 kHz

VBW 180 kHz

Span 20 MHz

Sweep 2.36 ms

Marker

-8.000000 MHz

-59.104 dB

Measured multitone Measured image rejection > 3.2 GHz

Page 17

Two-tone

Frequency spacing 100 Hz to 80 MHz (symmetrical about carrier) IM distortion 250 kHz to 3.2 GHz <–45 dBc for RF levels < 0dBm (typical) >3.2 GHz to 20 GHz <–55 dBc for RF levels < 0dBm (typical)

Measured two-tone

Basic modulation types (custom format)

PSK BPSK, QPSK, OQPSK, π/4DQPSK, 8PSK, 16PSK, D8PSK MSK User-defined phase offset from 0 to 100° QAM 4, 16, 32, 64, 256 FSK Selectable: 2, 4, 8, 16 level symmetric User defined Custom map of up to 16 deviation levels Symbol rate Maximum deviation < 5 MHz 4 times symbol rate 5 MHz to 50 MHz 20 MHz Resolution: 0.1 Hz

I/Q Custom map of 256 unique values Vector accuracy

Formats: BPSK, QPSK, 16-256QAM

(α= 0.3, Root Nyquist filter, symbol rate 4 Msym/s) EVM <1.2% RMS, < 0.8% RMS (typical) Origin offset 250 kHz to 3.2 GHz –45 dBc (typical)

3.2 to 20 GHz –50 dBc (typical)

FIR filter

Selectable Nyquist, root Nyquist, Gaussian, rectangular

α: 0 to 1, B

T: 0.1 to 1

Custom FIR 16-bit resolution, up to 64 symbols long, automatically

resampled to 1024 coefficients (max)

> 32 to 64 symbol filter: symbol rate ≤12.5 MHz

> 16 to 32 symbol filter: symbol rate ≤25 MHz

Internal filters switch to 16 tap when symbol rate is

between 25 and 50 MHz

Symbol rate

For external serial data: Adjustable from 1000 symbols/sec to a maximum symbol

rate of 50 Mbits/sec ÷ #bits/symbol For internally generated data: Adjustable from 1000 symbols/sec to 50 Msymbols/sec.

and a maximum of 8 bits per symbol. Modulation quality

may be degraded at high symbol rates. Baseband reference frequency Data clock can be phase locked to an external reference.

Input ECL, CMOS, TTL compatible, 50 Ω AC coupled

Internal baseband generator: real-time mode

(Option 602)

Ref-4 dBm Samp Log 10 dB/

LgAv 10 W1 S2 S3 FC

(f): #f>50K #Swp

#Atten 6 dB

Mkr1 -20.00 MHz

-62.275 dB

Center 20.000 00 GHz Res BW 470 kHz

VBW 470 kHz

Span 50 MHz

Sweep 1 ms

Marker

-20.000000 MHz

-62.275 dB

1. Measured with Agilent 89441A Vector Signal Analyzer. Valid after executing I/Q calibration, and instrument is

maintained within ± 5 °C of calibration temperature. RF power < 0 dBm. When external inputs are used, vector

accuracy can approach internal performance after system optinization. Recommended external I/Q input level

(I2+ Q2) = 0.3 V

rms

, I/Q modulator attenuator = 10 dB.

Page 18

Measured EVM

Measured spectral re-growth 5 GHz carrier with 16 QAM signal at 10 Msym/s

Frame trigger delay control

Range 0 to 1,048,575 bits Resolution 1 bit

Data types Internally generated data

Pseudo-random patterns PN9, PN11, PN15, PN20, PN23 Repeating sequence Any 4-bit sequence

Other fixed patterns

Direct-pattern RAM [PRAM]

Max size 32 Mb

(each bit uses an entire sample space) Use Non-standard framing

User file

Max size 3.2 MB Use Continuous modulation or internally generated

TDMA standard

Externally generated data

Type Serial data Inputs Data, data (bit) clock, symbol sync

Accepts data rates ±5% of specified data rate

Internal burst shape control

Varies with standards and bit rates Rise/fall time range Up to 30 bits Rise/fall delay range 0 to 63.5 bits

QPSK

Symbol rate (Msymbol/sec)

0 5 10 15 20 25 30 35 40 45 50

1 GHz 3 GHz 2 GHz 6 GHz 20 GHz 12 GHz

16QAM

Symbol rate (Msymbol/sec)

4.5

3.5

2.5

1.5

0.5

0 5 10 15 20 25 30 35 40 45 50

1 GHz 3 GHz 2 GHz 6 GHz 20 GHz 12 GHz

Ref-8 dBm Samp Log 10 dB/

LgAv 100 W1 S2 S3 FC

(f): #f>50K #Swp

#Atten 8 dB

Mkr1 12.00 MHz

--64.057 dB

Center 5.000 00 GHz Res BW 470 kHz

VBW 470 kHz

Span 50 MHz

Sweep 1 ms

-64.057 dB

Page 19

RF output frequency range: 3.2 to 20 GHz Input

Input (baseband) frequency range DC to > 500 MHz (nominal) Input impedance 50 Ω (nominal) Recommended input level 0 dBm (nominal) Maximum input voltage ±1 volt DC

I/Q offset adjustments ±50% RF path filters

Carrier Frequency Low-pass 3 dB cutoff frequency (nominal) >3.2 to 5 GHz 5.5 GHz >5 to 8 GHz 8.9 GHz > 8 to 12.8 GHz 13.9 GHz > 12.8 GHz 22.5 GHz

Measured I/Q frequency response

Wideband external I/Q inputs

(Option 015)

1. Operation close to RF filter cutoff frequencies will affect channel flatness.

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.4 -0.2 0.0 0.2 0.4

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.4 -0.2 0.0 0.2 0.4

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.4 -0.2 0.0 0.2 0.4

Offset from carrier (GHz)

Conversion loss (dB)

-5

-10

-15

-0.4 -0.2 0.0 0.2 0.4

6 GHz 10 GHz

15 GHz 20 GHz

Page 20

Interfaces GPIB (IEEE-488.2,1987) with listen and talk, RS-232,

and 10BaseT LAN interface. Control languages SCPI version 1997.0. Also will emulate most applicable

Agilent 836xxB, Agilent 837xxB, and Agilent 8340/41B

commands, providing general compatibility with ATE

systems which include these signal generators.

IEEE-488 functions

SH1, AH1, T6, TE0, L4, LE0, SR1, RL1, PP0, DC1, DT0, C0, E2. ISO compliant This family of signal generators is manufactured in an

ISO-9001 registered facility in concurrence with

Agilent Technologies commitment to quality.

Power requirements 90 to 267 Vac 50 to 60 Hz, (automatically selected),

650 W maximum. Operating temperature range 0 to 55 °C

Storage temperature range

–40 to 71 °C

With Option 005: –4 ° to 65 °C, gradient less than

20 °C/hour

Shock and vibration

Operating random vibration 5 to 500 Hz, 0.21 g rms Survival swept sine vibration 5 to 500 Hz, 0.75 g Survival random vibration 5 to 500 Hz, 2.09 g rms Functional shock (half-sine, 30 g, 11 ms) Meets the requirements of MIL-PRF-28800F for class and bench drop test 3 equipment. EMC Meets the conducted and radiated interference and

immunity requirements of IEC/EN 61326-1.

Meets radiated emission requirements of CISPR Pub 11/1997

Group 1 class A. Storage registers Memory is shared by instrument states, user data files,

sweep list files, and waveform sequences. Depending on

the number and size of these files, up to 800 storage

registers and 10 register sequences are available.

Security Display blanking. Compatibility Agilent Technologies 83550 Series millimeter heads (not

for use with I/Q modulation), Agilent Technologies 8757D

scalar network analyzers, Agilent Technologies EPM

Series power Meters. Self-test Internal diagnostic routine tests most modules (including

microcircuits) in a preset condition. For each module, if its

node voltages are within acceptable limits, then the

module “passes” the test.

Weight < 25 kg (54 lb.) net, < 33 kg (74 lb.) shipping. Dimensions 178 mm H x 426 mm W x 498 mm D

(7” H x 16.8” W x 19.6” D in.).

Recommended calibration cycle 24 months

RF output Nominal output impedance 50 Ω. Precision APC-3.5

male, or Type-N with Option 1ED. ALC input Used for negative external detector leveling.

Nominal input impedance 120 kΩ, damage level ±15 V. LF output Outputs the internally generated LF source. Nominal

output impedance 50 Ω. External input 1 Drives either AM, FM, or ΦM. Nominal input impedance

50 or 600 Ω, damage levels are 5 V

rms

and 10 V

peak

Remote programming

General specifications

Front panel connectors

(All connectors are BNC female unless otherwise noted.)

1. Save and recall of user files and instrument states from Option 005 Hard Drive is guaranteed only over the range 0 to 40 °C.

2. Storage below –20 °C instrument states may be lost.

3. Digital inputs and output are 3.3 V CMOS unless indicated otherwise. Inputs will accept 5 V CMOS, 3V CMOS, or TTL voltage levels.

Input/Output Descriptions

Page 21

External input 2 Drives either AM, FM, or ΦM. Nominal input impedance

50 or 600 Ω, damage levels are 5 V

rms

and 10 V

peak

Pulse/trigger gate input Accepts input signal for external fast pulse modulation.

Also accepts external trigger pulse input for internal pulse modulation. Nominal impedance 50 Ω. Damage levels are 5 V

rms

and 10 V

peak

Pulse video out Outputs a signal that follows the RF output in all pulse

modes. TTL-level compatible, nominal source impedance 50 Ω.

Pulse sync out Outputs a synchronizing pulse, nominally 50 ns width,

during internal and triggered pulse modulation. TTL-level compatible, nominal source impedance 50 Ω.

Data clock input Accepts a data clock signal to synchronize serial data for use

with internal baseband generator (Option 602). Maximum rate 50 MHz. Damage levels are > + 5.5 and <–0.5 V.

Data input Accepts serial data for use with internal baseband generator

(Option 602). Maximum rate 50 Mb/s. Data must be valid on the falling edges of data clock (normal mode) or the symbol sync (symbol mode). Damage levels are > + 5.5 and <–0.5 V.

I input Accepts an "I" input either for I/Q modulation or for

wideband AM. Nominal input impedance 50 or 600 Ω. Damage levels are 1 V

rms

and 5 V

peak

Q input Accepts a "Q" input for 1/0 modulation. Nominal input

impedance 50 or 600 Ω. Damage levels are 1 V

rms

and

5 V

peak

Symbol sync input Accepts symbol sync signal for use with internal baseband

generator (Option 602). Symbol sync might occur once per symbol or be a single, one bit wide pulse to synchronize the first bit of the first symbol. Maximum rate 50 MHz. Damage levels are >+5.5 and <–0.5 V.

Auxillary interface (Dual mode) Used for RS-232 serial communication and for Master/Slave

source synchronization. (9-pin D-subminiature female connector) For Master/Slave operation use Agilent Technologies part #8120-8806 Master/Slave interface cable.

GPIB Allows communication with compatible devices. LAN Allows 10baseT LAN communication 10 MHz input Accepts an external reference (timebase) input (at 1, 2,

2.5, 5, 10 MHz for standard and 10 MHz only for Option UNR) Nominal input impedance 50 Ω. Damage levels > +10 dBm

10 MHz output Outputs internal or external reference signal. Nominal

output impedance 50 Ω. Nominal output power +4 dBm

Sweep output (Dual mode) Supplies a voltage proportional to the RF power or

frequency sweep ranging form 0 volts at the start of sweep to +10 volts (nominal) at the end of sweep, regardless of sweep width.

When connected to an Agilent 8757D scalar network analyzer (Option 007), generates a selectable number of equally spaced 1 us pulses (nominal) across a ramp (analog) sweep. Number of pulses can be set form 101 to 1601 by remote control from the 8757D.

Output impedance: < 1 Ω, can drive 2000 Ω.

Rear panel connectors

(All connectors are BNC female unless otherwise noted.)

1. Digital inputs and output are 3.3 V CMOS unless indicated otherwise. Inputs will accept 5 V CMOS, 3V CMOS, or TTL voltage levels.

Page 22

Stop sweep In/Out Open-collector, TTL-compatible input/output. In ramp

sweep operation, provides low level (nominally 0 V) during sweep retrace and bandcross intervals, and high level during the forward portion of the sweep. Sweep will stop when grounded externally, sweep will resume when allowed to go high.

Trigger output (Dual mode) Outputs a TTL signal. High at start of dwell, or when waiting

for point trigger; low when dwell is over or point trigger is received, In ramp sweep mode, provides 1601 equally-spaced 1us pulses (nominal) across a ramp sweep. When using LF out, provides 2 us pulse at start of LF sweep.

Trigger input Accepts TTL signal for triggering point-to-point in manual

sweep mode, or to trigger start of LF sweep. Damage levels ≥ +10 V or ≤ –4 V.

Source module interface Provides bias, flatness correction, and leveling

connections to the Agilent model 83550 Series mm-wave source modules.

Source settled Provides an output trigger that indicates when the signal

generator has settled to a new frequency or power level. High indicates source not settled, Low indicates source settled.

Z-axis Blank/Markers During ramp sweep, supplies + 5 V (nominal) level during

retrace and bandswitch intervals. Supplies – 5 V (nominal) level when the RF frequency is at a marker frequency.

EFC > 0.25 ppm for –5 to +5 V Input impedance: >1 M Ω .25 – 3.2 GHz coherent carrier output Outputs RF signal modulated with FM or ΦM but not I/Q,

AM or pulse. Nominal power 0 dBm. Frequency range from 250 MHz to 3.2 GHz. Not useful for output frequency > 3.2 GHz. Damage levels 20 Vdc and 13 dBm reverse RF power. (SMA female)

Baseband generator reference input Accepts 0 to + 20 dBm sinewave, or TTL squarewave,

reference input to use as reference clock for the baseband generator (Option 602). Phase locks the internal data generator to the external reference: the RF frequency is still locked to the 10 MHz reference. Rate is 250 kHz to 100 MHz 50 Ω (nominal), AC coupled.

Burst gate input Accepts signal for gating burst power for use with internal

baseband generator (Option 602). The burst gating is used when you are externally supplying data and clock information. The input signal must be synchronized with the external data input that will be output during the burst. The burst power envelope and modulated data are internally delayed and re-synchronized. The input signal must be CMOS high for normal burst RF power or CW RF output power and CMOS low for RF off. Damage levels are >+5.5 and <–0.5 V.

Event 1 output In real-time mode, outputs a pattern or frame synchronization

pulse for triggering or gating external equipment, for use with internal baseband generator (Option 602). May be set to start at the beginning of a pattern, frame, or timeslot and is adjustable to within ± one timeslot with one bit resolution. In arbitrary waveform mode, outputs a timing signal generated by marker 1.

Event 2 output In real-time mode, outputs a data enable signal for gating

external equipment, for use with internal baseband generator (Option 602). Applicable when external data is clocked into internally generated timeslots. Data is enabled when signal is low. In arbitrary waveform mode, outputs a timing signal generated by marker 2.

Page 23

I and Q outputs Outputs the analog I/Q modulation signals from the internal

baseband generator. Nominal output impedance 50 Ω , DC-coupled. Damage levels ±3.5 V.

and Qoutputs Outputs the complement of the I and Q signals for

differential applications. Nominal output impedance 50 Ω, DC-coupled. Damage levels ±3.5 V.

Pattern trigger input Accepts signal to trigger internal pattern or frame generator

to start single pattern output, for use with internal baseband generator (Option 602). Minimum pulse width 100 ns. Damage levels are >+5.5 and <–0.5 V.

Wideband I and Q inputs Direct high-bandwidth analog inputs to I/Q modulator in

3.2 to 20 GHz range. Not calibrated. 0 dBm maximum. (Option 015 only)

Alternate power input Accepts CMOS signal for synchronization of external data

and alternate power signal timing. Damage levels are >+8 and <–4V.

Data clock output Relays a CMOS bit clock signal for synchronizing serial data. Data output Outputs data from the internal data generator or the

externally supplied signal at data input. CMOS signal.

Event 3 output In arbitrary waveform mode, outputs a timing signal

generated by marker 3. Damage levels >+8 and <4 V.

Event 4 output In arbitrary waveform mode, outputs a timing signal

generated by marker 4. Damage levels >+8 and <4 V.

Symbol sync output Outputs CMOS symbol clock for symbol synchronization,

one data clock period wide.

Auxiliary I/O connector (37-pin) used with Option 602

Model/option Description E8267C-520 Frequency range 250 kHz to 20 GHz E8267C-003 Enables digital output connectivity with N5102A E8267C-004 Enables digital input connectivity with N5102A E8267C-UNR Enhanced close-in phase noise E8267C-1E6 Narrow pulse modulation below 3.2 GHz E8267C-007 Ramp (analog) sweep E8267C-602 Internal baseband generator, 64 MSa memory E8267C-005 6 GB internal hard drive E8267C-015 Wideband external I/Q inputs E8267C-1ED Type-N (f) connector E8267C-1EM Moves all connectors to rear panel E8267C-1CM Rack mount kit E8267C-1CN Front handle kit E8267C-1CP Rack mount kit with front handle kit E8267C-408 Signal Studio software for enhanced multitone signals E8267C-417 Signal Studio software for 802.11 a/b/g WLAN signals E8267C-420 Signal Studio software for pulse building E8267C-421 Signal Studio software for noise power ratio E8267C-SP1 Signal Studio for jitter injection E8267C-HEH Improve low band harmonics (from 10 MHz to 3.2 GHz) 83554A Millimeter-wave source module (26.5 to 40 GHz) 83555A Millimeter-wave source module (33 to 50 GHz) 83556A Millimeter-wave source module (40 to 60 GHz) 83557A Millimeter-wave source module (50 to 75 GHz) 83558A Millimeter-wave source module (75 to 110 GHz) 8120-8806 Master/slave interface cable N5102A Baseband Studio digital signal interface module N5101A Baseband Studio PCI card N5110A Baseband Studio for waveform streaming N5110A-117 Hard drive streaming BW to 1 MSa/s N5110A-118 Extend hard drive streaming BW from 1 to 5 MSa/s N5110A-119 Extend hard drive streaming BW from 5 to 10 MSa/s N5110A-120 Extend hard drive streaming BW from 10 to 20 MSa/s N5110A-121 Extend hard drive streaming BW from 20 MSa/s up to 40 MSa/s N5110A-125 Signal generator hard drive streaming connectivity 9211-2656 Standard transit case 9211-7481 Tote-style transit case (includes wheels and telescoping handles)

Options, Accessories, and Related Products

Page 24

www.agilent.com/find/psg www.agilent.com/find/basebandstudio www.agilent.com/find/signalstudio

PSG Signal Generator, Brochure Literature number: 5988-7538EN

E8247C/57C PSG CW and Analog Signal Generator, Data Sheet

Literature number 5988-7454EN

E8267C PSG Vector Signal Generator

Data Sheet Literature number 5988-6632EN

PSG Self Guided Demo

Literature number 5988-2414EN

E8267C PSG Vector Signal Generator

Configuration Guide Literature number 5988-7541EN

Millimeter Wave Source Modules, Product Note Literature number 5988-2567EN

PSG Two-tone and Multitone Personalities

Application Note AN 1410 Literature number: 5988-7689EN

Signal Studio for Noise Power Ratio

Technical Overview Literature number 5988-9161EN

Signal Studio for Enhanced Multitone

Technical Overview Literature number 5988-5639EN

Signal Studio for 802.11 WLAN, Technical Overview Literature number 5988-8618EN

Baseband Studio Digital Signal Interface Module

Technical Overview Literature number 5988-9495EN

Baseband Studio for Waveform Streaming

Technical Overview Literature number: 5988-9493EN

www.agilent.com/find/emailupdates

Get the latest information on the products and applications you select.

Agilent Technologies’ Test and Measurement Support, Services, and Assistance

Agilent Technologies aims to maximize the value you receive, while minimizing your risk and problems. We strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need. Our extensive support resources and services can help you choose the right Agilent products for your applications and apply them successfully. Every instrument and system we sell has a global warranty. Support is available for at least five years beyond the production life of the product. Two concepts underlie Agilent’s overall support policy: “Our Promise” and “Your Advantage.”

Our Promise

Our Promise means your Agilent test and measurement equipment will meet its advertised performance and functionality. When you are choosing new equipment, we will help you with product information, including realistic performance specifications and practical recommendations from experienced test engineers. When you use Agilent equipment, we can verify that it works properly, help with product operation, and provide basic measurement assistance for the use of specified capabilities, at no extra cost upon request. Many self-help tools are available.

Your Advantage

Your Advantage means that Agilent offers a wide range of additional expert test and measurement services, which you can purchase according to your unique technical and business needs. Solve problems efficiently and gain a competitive edge by contracting with us for calibration, extra-cost upgrades, out-of-warranty repairs, and onsite education and training, as well as design, system integration, project management, and other professional engineering services. Experienced Agilent engineers and technicians worldwide can help you maximize your productivity, optimize the return on investment of your Agilent instruments and systems, and obtain dependable measurement accuracy for the life of those products.

Agilent T&M Software and Connectivity

Agilent’s Test and Measurement software and connectivity products, solutions and developer network allows you to take time out of connecting your instruments to your computer with tools based on PC standards, so you can focus on your tasks, not on your connections. Visit

www.agilent.com/find/connectivity

for more information.

By internet, phone, or fax, get assistance with all your test & measurement needs

Online Assistance:

www.agilent.com/find/assist

Product specifications and descriptions in this document subject to change without notice.

Phone or Fax United States:

(tel) 800 452 4844

Canada:

(tel) 877 894 4414 (fax) 905 282 6495

China:

(tel) 800 810 0189 (fax) 800 820 2816

Europe:

(tel) (31 20) 547 2323 (fax) (31 20) 547 2390

Japan:

(tel) (81) 426 56 7832 (fax) (81) 426 56 7840

Korea:

(tel) (82 2) 2004 5004 (fax) (82 2) 2004 5115

Latin America:

(tel) (305) 269 7500 (fax) (305) 269 7599 Taiwan: (tel) 0800 047 866 (fax) 0800 286 331

Other Asia Pacific Countries:

(tel) (65) 6375 8100 (fax) (65) 6836 0252 Email: tm_asia@agilent.com

Web Resources

Related Agilent Literature

Agilent Email Updates