Firmw
are Note
HP 70900A/B LO Module Firmware
ABCDE
HP Part No. 70900-90312
Printed in USA August 1996
Edition A.0.0
Notice
The information contained in this document is sub ject to change without notice.
Hewlett-Packard makes no warrantyofany kind with regard to this material, including,
but not limited to, the implied warranties of merchantability and tness for a particular
purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, p erformance, or use of this material.
Restricted Rights Legend.
Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth
in
subparagraph
at DFARS 252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the
Commercial Computer Software Restricted Rights clause at FAR 52.227-19 for other agencies.
(c)
(1)
(ii) of the Rights in Technical Data and Computer Software clause
c
Copyright Hewlett-Packard Company 1992|1994, 1996
All Rights Reserved. Reproduction, adaptation, or translation without prior written
permission is prohibited, except as allowed under the copyrightlaws.
1400 FountaingroveParkway,Santa Rosa, CA 95403-1799, USA
Certification
Hewlett-Packard Company certies that this product met its published specications at the
time of shipment from the factory. Hewlett-Packard further certies that its calibration
measuremen
ts are traceable to the United States National Institute of Standards and
Technology, to the extent allowed by the Institute's calibration facility, and to the calibration
facilities
W
arranty
This
of
other
Hewlett-P
In
ternational
ac
kard instrument product is warranted against defects in material and
Standards
Organization
mem
bers.
workmanship for a p eriod of one year from date of shipment. During the warranty period,
Hewlett-Packard Company will, at its option, either repair or replace products whichproveto
b
e defective.
For warranty service or repair, this product must be returned to a service facilit y designated
by Hewlett-Packard. Buyer shall prepayshippingcharges to Hewlett-Packard and
Hewlett-P
shall
from
ackard shall pay shipping charges to return the product to Buyer. However, Buyer
pa
y
all
another
shipping
coun
try
c
harges,
.
duties,
and taxes for products returned to Hewlett-Packard
Hewlett-P
ac
k
ard
w
arran
ts
that
its
soft
w
are
and rmware designated by Hewlett-Packard for
use with an instrument will execute its programming instructions when properly installed on
that instrument. Hewlett-Packard does not warrant that the operation of the instrument, or
soft
w
are,
or
rm
w
are
will be uninterrupted or error-free.
Limit
a
tion
of
W
arranty
The
main
foregoing
tenance
b
w
arran
y
Buy
ty shall not apply to defects resulting from improp er or inadequate
er,
Buy
er-supplied
soft
w
are or interfacing, unauthorized modication or
misuse, operation outside of the environmental specications for the product, or improper
site preparation or maintenance.
NO
OTHER
W
ARRANTY
IS
EXPRESSED OR IMPLIED. HEWLETT-PACKARD
SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusive Remedies
THE REMEDIES PR
OVIDED HEREIN ARE BUYER'S SOLE AND EX
CLUSIVE
REMEDIES. HEWLETT-PACKARD SHALL NOT BE LIABLE FOR ANY DIRECT,
INDIRECT, SPECIAL, INCIDENT
AL, OR CONSEQUENTIAL D
AMAGES, WHETHER
BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.
Assistance
Product maintenanceagreements and other customer assistanceagreements are available for
Hewlett-Packardproducts.
For any assistance, contact your nearest Hewlett-Packard Sales and Service Oce.
iii
Safety Symbols
The following safety symbols are used throughout this manual. Familiarize yourself with each
of the symbols and its meaning before operating this instrument.
CA
UTION
UTION
sign
denotes
a hazard. It calls attention to a procedure
The
CA
which, if not correctly performed or adhered to, could result in damage to
or destruction of the product or the user's work. Do not proceed beyond a
CA
W
ARNING
UTION
The
WARNING
sign
until the indicated conditions are fully understood and met.
sign denotes a hazard. It calls attention to a procedure which,
if not correctly performed or adhered to, could result in injury to the user. Do
D
ANGER
not proceed beyond a
understood
The
DANGER
and
met.
sign denotes an imminent hazard to people. It warns the reader
WARNING
sign until the indicated conditions are fully
of a procedure which, if not correctly performed or adhered to, could result
in injury or loss of life. Do not proceed beyond a
indicated
conditions
are
fully
understood
and met.
DANGER
sign until the
iv
General Safety Considerations
The
WARNING
instructions in this document are for use by qualified personnel only.To
avoid electrical shock, do not perform any servicing unless you are qualified
to
do
so.
The opening of covers or removal of parts is likely to expose dangerous
voltages. Disconnect the instrument from all voltage sources while it is being
opened.
The power cord is connected to internal capacitors that may remain live for
five seconds after disconnecting the plug from its power supply.
This
is
a
Safety Class 1 Product (provided with a protective earthing ground
incorporated in the power cord). The mains plug shall only be inserted in a
socket outlet provided with a protective earth contact. Any interruption of the
protectiv
e conductor inside or outside of the instrument is likely to makethe
instrument dangerous. Intentional interruption is prohibited.
For continued protection against fire hazard, replace fuse only with same
type
and
ratings, (type nA/nV). The use of other fuses or materials is
prohibited.
W
ARNING
Before
grounded
this
instrument
through
the
is
switched
protectiv
on, make sure it has been properly
e
conductor
of
the
ac
po
w
er
cable to a socket
outlet provided with protective earth contact.
Any interruption of the protective (grounding) conductor, inside or outside
the instrument, or disconnection of the protective earth terminal can result in
personal
injury
.
Before this instrument is switched on, make sure its primary power circuitry
has been adapted to the voltage of the ac power source.
Failure to set the ac power input to the correct voltage could cause damage
to the instrument when the ac power cable is plugged in.
v
1
HP 70900A/B LO Module Firmware
The HP 70900A/B local oscillator source contains a program in read-only memory (ROM),
referred
to
as
rm
w
are,
that
is used to control both the HP 70900A/B lo cal oscillator source
as well as other modules in a Modular Measurement System (MMS). The rmware is revised
periodically to eliminate known defects (bugs) and intro duce new features.
Depending on the rmware in your HP 70900A/B lo cal oscillator source, you can determine
its
curren
t
v
ersion by either a revision date code or a
Version.Update.Fix
(V.U.F) code.
Understanding
Ev
ery set of HP 70900A/B local oscillator source rmware has a revision date code. The
revision
This
date
revision
co
date
de
corresp
co
Revision
onds
de
is
referred
to
Date
the
to
Code
year, month, and day that the rmware was last revised.
when
determining
supp
orted
commands
or
system
error
codes.
Eachrmware revision date co de has a dierent part number. If the part number for a
particular
rmware revision date code is ordered, a new ROM board is shipped.
Understanding Version Update Fix (V.U.F) Code
Curren
t
rm
w
are
no
w
con
tains a unique code called the
Version.Update.Fix
(V.U.F) code.
The V.U.F co de is enclosed in parenthesis and immediately follows the currentdatecode.
In the V.U.F code, the
to the op erator and do not aect any of the documentation for the system. The
Fix
number refers to changes made to the rmware that are invisible
Update
number refers to changes made to the rmware that may add or repair features for a
particular product. When this n
required. When the
user in
Because the
terface and completely new do cumen
Fix
Version
number can change on the most currentrmware and remain invisible to the
operator, it may be dierent than the
this
Fix
number may be dierent, your documentation will still apply. When the
number or
Version
letter changes on the most currentrmware, the changed information will
umber changes, updates to the current documentation maybe
changes, this means that major changes have been made to the
tation may be required.
Fix
number listed in your documentation. Although
Update
either be implemented in the documentation or made available for the do cumentation that is
shipped with the HP 70900A/B local oscillator source, HP 70860A controller board upgrade
kit for the HP 70900A, and the HP 70861A RAM/ROM upgrade kit.
HP 70900A/B LO Module Firmware 1-1
Determining
T
o
determine
the
Date
the
date code and V.U.F code of your rmware in an HP 70900A/B local
Code
and
V.U.F
oscillator source, p erform the following steps:
1. Press the menukey on the display:
use
the
or use the
displa
y
2.
When the menu screen appears, press the
3.
On
the
service
curren
t
rm
If
supp
orted,
4
MNU
w
5
k
ey for the HP 70205A graphics display
4
5
MENU
key for the HP 70206A system graphics display or HP 70004A color
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
ROM
screen,
are
the
press
the
v
ersion is displayed in the general annotation block of the display.
V.U.F
code is enclosed in parenthesis and immediately follows the
VERSION
revision date code.
Code of your LO's Firmware
NNNNNNNNNNNNNN
Misc
NNNNNNNNNNNNNN
,
MORE
softk
ey
,and
.
The
NNNNNNNNNNNNNNNNNNNNNNN
service
revision
softkeys.
date code of the
Current
Firmw
are
Date Code and V.U.F Code of your LO
The current date co de and V.U.F code of the rmware being shipped in the HP 70900A/B
local oscillator source is 960418 (B.06.03). This current rmware date co de and V.U.F co de
sup
ersedes
F
or
module sp ecic commands and LO enhancements that were released for dierent revision
date
Modules
The
curren
co
des
Supported
all
and
t
date
previous
V.U.F
b
co
de
date
co
des,
y
Current
and
codes and V.U.F co des.
see
Firmw
V.U.F
Chapter
co
are
de
2.
Date
Code
of
y
our rmware applies to:
and
V.U.F
Code
HP 70900A/B lo cal oscillator source
HP
70860A controller board upgrade kit for the HP 70900A
HP
and
70861A
supp
orts
RAM/R
the
follo
OM
upgrade
wing mo dules:
kit
HP 70300A RF tracking generator
HP 70301A microwave tracking generator
HP 70310A precision frequency reference
HP 70600A preselector
HP 70601A preselector
HP 70620A preamplier
HP 70620B preamplier
HP 70621A preamplier
HP 70700A digitizer
HP 70810B light
wave section
HP 70902A IF section
HP 70903A IF section
HP 70904A RF section
HP 70905A RF section
HP 70905B RF section
HP 70906A RF section
HP 70906B RF section
HP 70907A external millimeter interface module
HP 70907B external millimeter interface module
1-2 HP 70900A/B LO Module Firmware
HP 70908A RF section
HP
70909A
RF
section
HP 70910A RF section
HP 70911A WB IF section
Displaying the Date Code of Your System Display's Firmware
Your system display also has its own set of rmware that is separate from the rmware in the
HP
70900A/B
lo
cal
oscillator
source.
The
rmware version of the system displays maybe
observed in twoways:
At instrument start-up, the rmware version and date appears on the display for several
seconds.
During instrument operation, the rmware date and displayversion maybe viewed by
pressing the keys listed below.
for
HP
70205A graphics display or HP 70206A system graphics display:
1. press the
2.
press the
3.
press
for
HP
1. press the
2.
press
3.
press
4
5
DISP
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
display tests
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
DISPLAY
the
70004A
the
the
color
4
DISPLA
NNNNNNNNNNNNNN
Misc
N
N
N
N
N
N
N
N
N
N
N
N
DISPLAY
key,
ID
displa
5
key,
Y
softk
N
NNNNNNNNNNNNNNNNNNN
ID
softk
ey
,
softkey.
softkey,
ey.
y:
Current Date Code of Your System Display's Firmware
The current date code of the rmware being shipped in the HP 70004A color displayis
960424
co
The
des.
R
OM Version 7.06. This currentrmware date code supersedes all previous date
curren
t
date
co
de
of the rmware being shipped in the HP 70205A graphics displayor
HP 70206A system graphics display is 960424 ROM Version 7.06 . This current rmware date
code sup ersedes all previous date codes.
Previous Date Codes of Your System Display's Firmware
HP 70004A color display
Date Co de ROM Version
960424 ROM Version 7.06
930416 ROM Version 7.04
900316 ROM Version 7.03
891010 ROM Version 7.01
890622 ROM Version 7.00
HP 70205A graphics display
HP 70206A system graphics display
Date Co de ROM Version
960424 ROM Version 7.06
860625 ROM Version 6.0
Feb1985 ROM Version 5.0
HP 70900A/B LO Module Firmware 1-3
Remote Command History
This chapter contains a set of tables that contain dierent sets of remote commands. Each
table
sho
ws
the
set
of
mo
dule specic commands and LO enhancements that were released for
each revision date code and V.U.F code. All of the remote commands in these tables apply
only to the rmware used in the HP 70900A/B lo cal oscillator source. The details of these
remote
Manual
commands
.
are
do
cumen
ted in the
HP 70000 Modular Spectrum Analyzer Programming
2
Remote Command History 2-1
Date
850730
Co
de
V.U.F
A.00.01
Initially
Supp
orted Modules:
HP 70900A lo cal oscillator source
HP 70902A IF section
HP 70903A IF section
HP 70904A RF section
HP
70905A
RF
section
HP 70906A RF section
Initial Remote Commands:
ABORT ABS ADD AMB AMBPL AMPCOR
AMPU ANNOT APB AT AUNITS AVG
AXB
BIT
BLANK
BML
BX
C
CAL
CALCOR CALFREQ CALPWR CALSRC CATALOG CF
CLRDSP CLRW CNVLOSS COMPRESS CONCAT CONFIG
CONTS COUPLE DEBUG DELETE DET DISPOSE
DIV DL DONE DSPLY DSPMODE DWINDOW
ENTER ERACE ERR EXP FA FB
FFT FFTKNL FOFFSET FREQ FS FULBAND
FUNCDEF
ID
IFTKNL
IWINDO
LN
MBMAX
MEM
W
GRAPH
IDCF
INPUT
KEYCLR
LOG
MBMIN
MIN
GRA
T
IDFREQ
INT
KEYDEF
LOST
AR
MBRES
T
GRID
IDMODE
INZ
KEYPST
LOSTOP
MDS
HD
IDST
IP
LG
MBIAS
MEAN
HNLOCK
A
T
IF
IT
LINET
MBIASPK
MEASU
MINH MK MKA MKACT
MKAL MKAR MKBW MKCF MKD MKF
MKN MKNOISE MKOFF MKP MKPAUSE MKPK
MKPX MKREAD MKSP MKSS MKT MKTRACE
MKTRACK MKTV MKTYPE ML MOD MODID
MOV MPY MSG MXM MXMH NSTART
NSTATE NSTOP ONEOS OP OR OUTPUT
PA PATHLOCK PAUSE PD PDA PDF
PEAKS PEN PINPUT PLOT POSU POWER
ON
PROCEDURE PSTATE PU PWRBW RB RBR
RCLS READMENU RELHPIB REPEAT RETURN REV
RL RLPOS RMS ROFFSET RQS SAVES
SCALE SER SIGDEL SIGID SMOOTH SNGLS
SP SQR SRQ SS ST STATE
STB STDEV SUB SUM SUMSQR TDF
TEST TEXT TH TITLE TM TP
TRCOND TRDEF TRDSP TRPST TRSTAT TS
TWINDOW USERERR USERKEY USTATE VARDEF VARIANCE
VAVG VB VBR VIEW VTH VTL
VW WAIT XCH XERR
2-2 Remote Command History
Mo
dule
Support Added:
Date
Co
de
860203
HP 70300A RF tracking generator
HP 70907A external millimeter interface module
V.U.F
A.01.00
Remote
Commands
Added:
A1 A2 A3 A4 B1 B2
B3 B4 BL BTC C1 C2
CA CALDATA CALL CALV CR CS
CT CV DSPTEXT E1 E2 E3
E4 ELSE ELSIF ENDIF EX FREQU
HNUNLK L0 M1 M2 M3 MA
MEASURE
MF
MIL
MKMIN
MKRL
MT
PR RC S1 S2 SRCALC SRCAM
SRCAMF SRCAT SRCBLNK SRCMOD SRCOSC SRCPOFS
SRCPSTP SRCPSWP SRCPWR SRCTK SRCTKPK STORREF
SV T0 THEN TIME TRA TRB
TRC UNTIL
Mo
dule Support Added:
Date Co de
861015
V.U.F
A.02.00
HP 70600A preselector
HP
Remote
Commands
CLS
PRSENABL
USERLOCK
70601A
INPUTMOD
PRSHYST
USERMSG
Added:
preselector
MOD
PSD
ADD
A
C PSENABLE PSHYST TRPRST
PP
PR
OTECT
PRSDAC
Date Co de
870501
V.U.F
A.03.00
Module Support Added:
HP 70908A RF section
HP 70700A digitizer
Remote Commands Added:
ADC EBLOB EXTIF FLIMIT NOP PADC
PTBL PTEL
Remote Command History 2-3
Mo
dule
Support Added:
Date
Co
de
880314
HP 70620A preamplier
HP 70810A lightwave section
V.U.F
B.00.00
Remote
Commands
Added:
ACTPARM FIRMKEYS OOFFSET OPTICAL PERASE PREAMP
RCLU SAVEU ZOOMRB
Date Co de
880901
V.U.F
B.01.00
Module Support Added:
HP
70301A
micro
w
a
ve tracking generator
HP 70871A scalar p ersonalitykit
Remote
Commands Added:
LIMIAMP LIMIBEEP LIMIDEL LIMIDONE LIMIEDIT LIMIFAIL
LIMIFREQ LIMIHALF LIMILINE LIMINEXT LIMIRCL LIMIREL
LIMISAV LIMISDEL LIMISEG LIMITEST LIMITYPE
Date Co de
890606
891102
900314
V.U.F
B.02.00
B.02.01
B.03.00
Module Support Added:
HP 70900B lo cal oscillator source
HP 70004A color display
HP 70907B external millimeter interface module
HP 70620B preamplier
HP 70621A preamplier
Remote Commands Added:
ACTDEF ASWP CORTOLIM DLP FETCH FORMAT
HP LIMIBOT LIMISCRL LIMISEL LIMITOCOR LOAD
MSI ONMKR OVRSWP PERSIST PREFX PURGE
RCLD RCLT SAVED SAVET STA STOR
TR XNOISE
2-4 Remote Command History
V.U.F
B.03.01
Mo
dule
Support Added:
Date
901008
Co
de
BDLP
GSM
128K & 1M RAM
Remote Commands Added:
APROGDEF CHEIGHT CWIDTH D1 D2 D3
DATADEF DD DLE DR DW EXTMXR
FPKA GR KBDPT KS[35] KS[40] KS[41]
KS[44] KS[47] KS[61] KS[91] KS[92] KS[94]
KSA KSB KSC KSD KSE KSF
KSG
KSH
KSI
KSJ
KSK
KSL
KSM KSN KSO KSP KSQ KSR
KSS KST KSU KSV KSW KSX
KSY KSZ KSa KSb KSc KSd
KSe KSf KSg KSh KSi KSj
KSk KSl KSm KSn KSo KSp
KSq KSr KSs KSt KSu KSv
KSw
MK
OL
R2
T3
CONT
KSx
MKSTOP
ONMENU
R3
T4
KSy
O1
ONUSER
R4
T
A
KSz
O2
ONWINDO
SW
TB
W
LL
O3
PR
T1
THE
OGDEF
M4
O4
R1
T2
UR
VBO
Date
910802
911021
Code
V.U.F
B.04.00
B.04.01
Module Support Added:
HP 70810B lightwave section
HP 70909A RF section
HP 70910A RF section
HP 8566B spectrum analyzer remote command compatibility
Remote Commands Added:
ANNOFF BLANKFT CLRAVG CTA CTM DT
EE EP FALIMIT FIRMKYS IB IGEN
IGENDTYCY IGENPW LAMBDA LB LF MKBWA
MKRELPWR MKRINSYS OPTATN OPTMODE OPTPWR OT
PWRBAR PWRBARON PWRMODE RSPSVTY SENS SP
SWEEP SYSCOR USRPWR XDAC XYPEAK YDAC
Remote Command History 2-5
Date
920325
920527
Co
de
V.U.F
B.04.02
B.04.03
1
Module Support Added:
HP
70950A
optical spectrum analyzer
HP 70951A optical sp ectrum analyzer
Remote Commands Added:
CORSEL
IDN
LIGHT
MKTUNE
OPTSW
PDMEAS
PTTIMEOUT THREED THREEDH THREEDV XAMPSW
1
The rmware with V.U.F code B.04.02 did not ship in the HP 70900B local oscillator source. This rmware was
only shipp ed in the HP 70950A optical sp ectrum analyzer and HP 70951A optical spectrum analyzer.
V.U.F
B.04.04
Mo
dule Support Added:
Date
920724
Co
de
None added. Corrected a system error.
Remote
Module Support Added:
Commands
None
Added:
Date
940120
added.
Co
1
de
V.U.F
B.05.00
HP 70911A WB IF section
Remote Commands Added:
ADAPBPCTL ADAPBTL ADBTL ADCTL AMBMC AMBMCPL
AMCPL APBDCTL AXC BP CLRPAVG CPLAVG
CPLDET DA DETSEL EXTVID GRATSCRL KS~
MKDACT MKDREFA MKDREFF MKFABS MKPABS MKPITX
NORM OVRW PC PCDELTA PWRAVG RCVRMODE
RELADC RELMOD SG STARTUP SWPMODE TRIGDEL
USERWARN VTDL WARN WARNCTRL XWARN YLABELS
1
Firmware doesn't support GSM or MEM+ controller b oards.
Date Co de
960418
Module Support Added:
1
None added. Corrected system errors.
Remote Commands Added:
None added.
1
Firmware doesn't support GSM or MEM+ controller b oards.
2-6 Remote Command History
V.U.F
B.06.03
Remote Commands/Date Codes/V.U.F Codes
The following tables list all of the reserved words used by the HP 70900A/B local oscillator
source
HP 70951A optical spectrum analyzer.
Each command is shown along with the revision date code and V.U.F code of the rmware
that it was released with. All of the remote commands in these tables apply only to the
rm
commands are do cumented in the
Manual
con
trolled
w
are
used
.
mo
dules
as
w
ell as the HP 70950A optical spectrum analyzer and
in the HP 70900A/B lo cal oscillator source. The details of these remote
HP 70000 Modular Spectrum Analyzer Programming
3
Remote Commands/Date Codes/V.U.F Codes 3-1
Command Date Code V.U.F Code
A1 860203 A.01.00
A2 860203 A.01.00
A3 860203 A.01.00
A4 860203 A.01.00
ABORT 850730 A.00.01
ABS 850730 A.00.01
A
CTDEF
890606,
891102,
900314
B.02.00,
B.02.01,
ACTPARM 880314 B.00.00
AD
APBPCTL
940117 B.05.00
ADAPBTL 940117 B.05.00
ADBTL 940117 B.05.00
ADC 870501 A.03.00
ADCTL 940117 B.05.00
ADD 850730 A.00.01
AMB 850730 A.00.01
AMBMC 940117 B.05.00
AMBMCPL 940117 B.05.00
AMBPL 850730 A.00.01
AMCPL 940117 B.05.00
AMPCOR 850730 A.00.01
AMPU 850730 A.00.01
ANNOFF 910802,
911021
B.04.00,
B.04.01
ANNOT 850730 A.00.01
APB 850730 A.00.01
APBDCTL 940117 B.05.00
APROGDEF 901008 B.03.01
ASWP 890606,
A
T
891102,
900314
850730 A.00.01
B.02.00,
B.02.01,
AUNITS 850730 A.00.01
AVG 850730 A.00.01
AXB 850730 A.00.01
AX
C
940117 B.05.00
B1 860203 A.01.00
B2 860203 A.01.00
B3 860203 A.01.00
B4 860203 A.01.00
BIT 850730 A.00.01
BL 860203 A.01.00
BLANK 850730 A.00.01
BLANKFT 910802, 911021 B.04.00, B.04.01
B.03.00
B.03.00
3-2 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
BML 850730 A.00.01
BP 940117 B.05.00
BTC 860203 A.01.00
BXC 850730 A.00.01
C1 860203 A.01.00
C2 860203 A.01.00
CA 860203 A.01.00
CAL 850730 A.00.01
CALCOR 850730 A.00.01
CALDATA 860203 A.01.00
CALFREQ 850730 A.00.01
CALL 860203 A.01.00
CALPWR 850730 A.00.01
CALSRC 850730 A.00.01
CAL
V
860203 A.01.00
CATALOG 850730 A.00.01
CF 850730 A.00.01
CHEIGHT 901008 B.03.01
CLRA
V
G
910802,
911021
B.04.00,
B.04.01
CLRDSP 850730 A.00.01
CLRPAVG 940117 B.05.00
CLR
W
850730 A.00.01
CLS 861015 A.02.00
CNVLOSS 850730 A.00.01
COMPRESS 850730 A.00.01
CONCAT 850730 A.00.01
CONFIG 850730 A.00.01
CONTS 850730 A.00.01
CORSEL 920325, 920527 B.04.021, B.04.03
CORTOLIM 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
COUPLE 850730 A.00.01
CPLAVG 940117 B.05.00
CPLDET 940117 B.05.00
CR 860203 A.01.00
CS 860203 A.01.00
CT 860203 A.01.00
CTA 910802, 911021 B.04.00, B.04.01
CTM 910802, 911021 B.04.00, B.04.01
CV 860203 A.01.00
CWIDTH 901008 B.03.01
1
The rmware with V.U.F code B.04.02 did not ship in the HP 70900B lo cal
oscillator source. This rmware was only shipp ed in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
Remote Commands/Date Codes/V.U.F Codes 3-3
Command Date Code V.U.F Code
D1 901008 B.03.01
D2 901008 B.03.01
D3 901008 B.03.01
DA 940117 B.05.00
DATADEF 901008 B.03.01
DD 901008 B.03.01
DEBUG 850730 A.00.01
DELETE 850730 A.00.01
DET 850730 A.00.01
DETSEL 940117 B.05.00
DISPOSE 850730 A.00.01
DIV 850730 A.00.01
DL 850730 A.00.01
DLE 901008 B.03.01
DLP 890606,
891102,
900314
B.02.00,
B.02.01,
DONE 850730 A.00.01
DR 901008 B.03.01
DSPL
Y
850730 A.00.01
DSPMODE 850730 A.00.01
DSPTEXT 860203 A.01.00
DT 910802, 911021 B.04.00, B.04.01
D
W
D
WINDO
W
901008 B.03.01
850730 A.00.01
E1 860203 A.01.00
E2 860203 A.01.00
E3 860203 A.01.00
E4 860203 A.01.00
EBLOB 870501 A.03.00
EE 910802, 911021 B.04.00, B.04.01
ELSE 860203 A.01.00
ELSIF 860203 A.01.00
ENDIF 860203 A.01.00
ENTER 850730 A.00.01
EP 910802, 911021 B.04.00, B.04.01
ERACE 850730 A.00.01
ERR 850730 A.00.01
EX 860203 A.01.00
EXP 850730 A.00.01
EXTIF 870501 A.03.00
EXTMXR 901008 B.03.01
B.03.00
3-4 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
EXTVID 940117 B.05.00
FA 850730 A.00.01
FALIMIT 910802, 911021 B.04.00, B.04.01
FB 850730 A.00.01
FETCH 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
FFT 850730 A.00.01
FFTKNL 850730 A.00.01
FIRMKEYS 880314 B.00.00
FIRMKYS 910802,
911021
B.04.00,
B.04.01
FLIMIT 870501 A.03.00
F
OFFSET
F
ORMA
T
890606,
850730 A.00.01
891102,
900314
B.02.00,
B.02.01,
B.03.00
FPKA 901008 B.03.01
FREQ 850730 A.00.01
FREQU 860203 A.01.00
FS 850730 A.00.01
FULBAND 850730 A.00.01
FUNCDEF 850730 A.00.01
GR 901008 B.03.01
GRAPH 850730 A.00.01
GRA
T
850730 A.00.01
GRATSCRL 940117 B.05.00
GRID 850730 A.00.01
HD 850730 A.00.01
HNLOCK 850730 A.00.01
HNUNLK 860203 A.01.00
HP 890606,
891102,
900314
B.02.00,
B.02.01,
B.03.00
IB 910802, 911021 B.04.00, B.04.01
ID 850730 A.00.01
IDCF 850730 A.00.01
IDFREQ 850730 A.00.01
IDMODE 850730 A.00.01
IDN 920325, 920527 B.04.021, B.04.03
IDSTAT 850730 A.00.01
IF 850730 A.00.01
IFTKNL 850730 A.00.01
IGEN 910802, 911021 B.04.00, B.04.01
IGENDTYCY 910802, 911021 B.04.00, B.04.01
IGENPW 910802, 911021 B.04.00, B.04.01
INPUT 850730 A.00.01
1
The rm
ware with V.U.F co de B.04.02 did not ship in the HP 70900B local
oscillator source. This rmware was only shipp ed in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
Remote Commands/Date Codes/V.U.F Codes 3-5
Command Date Code V.U.F Code
INPUTMOD 861015 A.02.00
INT 850730 A.00.01
INZ 850730 A.00.01
IP 850730 A.00.01
IT 850730 A.00.01
IWINDOW 850730 A.00.01
KBDPT 901008 B.03.01
KEYCLR 850730 A.00.01
KEYDEF 850730 A.00.01
KEYPST 850730 A.00.01
KSA 901008 B.03.01
KSB 901008 B.03.01
KSC 901008 B.03.01
KSD 901008 B.03.01
KSE 901008 B.03.01
KSF 901008 B.03.01
KSG 901008 B.03.01
KSH 901008 B.03.01
KSI 901008 B.03.01
KSJ 901008 B.03.01
KSK 901008 B.03.01
KSL 901008 B.03.01
KSM 901008 B.03.01
KSN 901008 B.03.01
KSO 901008 B.03.01
KSP 901008 B.03.01
KSQ 901008 B.03.01
KSR 901008 B.03.01
KSS 901008 B.03.01
KST 901008 B.03.01
KSU 901008 B.03.01
KSV 901008 B.03.01
KSW 901008 B.03.01
KSX 901008 B.03.01
KSY 901008 B.03.01
KSZ 901008 B.03.01
KS[35] 901008 B.03.01
KS[40] 901008 B.03.01
KS[41] 901008 B.03.01
KS[44] 901008 B.03.01
3-6 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
KS[47] 901008 B.03.01
KS[61] 901008 B.03.01
KS[91] 901008 B.03.01
KS[92] 901008 B.03.01
KS[94] 901008 B.03.01
KSa 901008 B.03.01
KSb 901008 B.03.01
KSc 901008 B.03.01
KSd 901008 B.03.01
KSe 901008 B.03.01
KSf 901008 B.03.01
KSg 901008 B.03.01
KSh 901008 B.03.01
KSi 901008 B.03.01
KSj 901008 B.03.01
KSk 901008 B.03.01
KSl 901008 B.03.01
KSm 901008 B.03.01
KSn 901008 B.03.01
KSo 901008 B.03.01
KSp 901008 B.03.01
KSq 901008 B.03.01
KSr 901008 B.03.01
KSs 901008 B.03.01
KSt 901008 B.03.01
KSu 901008 B.03.01
KSv 901008 B.03.01
KSw 901008 B.03.01
KSx 901008 B.03.01
KSy 901008 B.03.01
KSz 901008 B.03.01
KS~ 940117 B.05.00
L0 860203 A.01.00
LAMBDA 910802, 911021 B.04.00, B.04.01
LB 910802, 911021 B.04.00, B.04.01
LF 910802, 911021 B.04.00, B.04.01
LG 850730 A.00.01
LIGHT 920325, 920527 B.04.021, B.04.03
LIMIAMP 880901 B.01.00
LIMIBEEP 880901 B.01.00
1
The rmware with V.U.F code B.04.02 did not ship in the HP 70900B lo cal
oscillator source. This rmware was only shipp ed in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
Remote Commands/Date Codes/V.U.F Codes 3-7
Command Date Code V.U.F Code
LIMIBOT 890606,
891102,
900314
B.02.00,
B.02.01,
B.03.00
LIMIDEL 880901 B.01.00
LIMIDONE 880901 B.01.00
LIMIEDIT 880901 B.01.00
LIMIFAIL 880901 B.01.00
LIMIFREQ 880901 B.01.00
LIMIHALF 880901 B.01.00
LIMILINE 880901 B.01.00
LIMINEXT 880901 B.01.00
LIMIR
CL
880901 B.01.00
LIMIREL 880901 B.01.00
LIMISAV 880901 B.01.00
LIMISCRL 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
LIMISDEL 880901 B.01.00
LIMISEG 880901 B.01.00
LIMISEL 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
LIMITEST 880901 B.01.00
LIMITOCOR 890606,
891102,
900314
B.02.00,
B.02.01,
B.03.00
LIMITYPE 880901 B.01.00
LINET 850730 A.00.01
LL 901008 B.03.01
LN 850730 A.00.01
LO
AD
890606,
891102,
900314
B.02.00,
B.02.01,
B.03.00
LOG 850730 A.00.01
LOSTART 850730 A.00.01
LOSTOP 850730 A.00.01
M1 860203 A.01.00
M2 860203 A.01.00
M3 860203 A.01.00
M4 901008 B.03.01
MA 860203 A.01.00
MBIAS 850730 A.00.01
MBIASPK 850730 A.00.01
MBMAX 850730 A.00.01
MBMIN 850730 A.00.01
MBRES 850730 A.00.01
MDS 850730 A.00.01
MEAN 850730 A.00.01
MEASU 850730 A.00.01
MEASURE 860203 A.01.00
3-8 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
MEM 850730 A.00.01
MF 860203 A.01.00
MIL 860203 A.01.00
MIN 850730 A.00.01
MINH 850730 A.00.01
MK 850730 A.00.01
MKA 850730 A.00.01
MKA
CT
850730 A.00.01
MKAL 850730 A.00.01
MKAR 850730 A.00.01
MKBW 850730 A.00.01
MKBWA 910802, 911021 B.04.00, B.04.01
MKCF 850730 A.00.01
MKCONT 901008 B.03.01
MKD 850730 A.00.01
MKDACT 940117 B.05.00
MKD
A
CT?
MKDREF
A
940117 B.05.00
940117 B.05.00
MKDREFF 940117 B.05.00
MKF 850730 A.00.01
MKFABS 940117 B.05.00
MKMIN 860203 A.01.00
MKN 850730 A.00.01
MKNOISE 850730 A.00.01
MKOFF 850730 A.00.01
MKP 850730 A.00.01
MKPABS 940117 B.05.00
MKPAUSE 850730 A.00.01
MKPITX 940117 B.05.00
MKPK 850730 A.00.01
MKPX 850730 A.00.01
MKREAD 850730 A.00.01
MKRELPWR 910802, 911021 B.04.00, B.04.01
MKRINSYS 910802, 911021 B.04.00, B.04.01
MKRL 860203 A.01.00
MKSP 850730 A.00.01
MKSS 850730 A.00.01
MKSTOP 901008 B.03.01
MKT 850730 A.00.01
MKTRACE 850730 A.00.01
Remote Commands/Date Codes/V.U.F Codes 3-9
Command Date Code V.U.F Code
MKTRA
CK
850730 A.00.01
MKTUNE 920325, 920527 B.04.021, B.04.03
MKTV 850730 A.00.01
MKTYPE 850730 A.00.01
ML 850730 A.00.01
MOD 850730 A.00.01
MODADD 861015 A.02.00
MODID 850730 A.00.01
MO
V
850730 A.00.01
MPY 850730 A.00.01
MSG 850730 A.00.01
MSI 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
MT 860203 A.01.00
MXM 850730 A.00.01
MXMH 850730 A.00.01
NOP 870501 A.03.00
NORM 940117 B.05.00
NSTART 850730 A.00.01
NST
A
TE
850730 A.00.01
NSTOP 850730 A.00.01
O1 901008 B.03.01
O2 901008 B.03.01
O3 901008 B.03.01
O4 901008 B.03.01
OL 901008 B.03.01
ONEOS 850730 A.00.01
ONMENU 901008 B.03.01
ONMKR 890606,
891102, 900314
B.02.00,
B.02.01, B.03.00
ONUSER 901008 B.03.01
ONWINDOW 901008 B.03.01
OOFFSET 880314 B.00.00
OP 850730 A.00.01
OPTATN 910802, 911021 B.04.00, B.04.01
OPTICAL 880314 B.00.00
OPTMODE 910802, 911021 B.04.00, B.04.01
OPTPWR 910802, 911021 B.04.00, B.04.01
OPTSW 920325, 920527 B.04.021, B.04.03
OR 850730 A.00.01
OT 910802, 911021 B.04.00, B.04.01
OUTPUT 850730 A.00.01
1
The rmware with V.U.F code B.04.02 did not ship in the HP 70900B local
oscillator source. This rmware was only shipp ed in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
3-10 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
O
VRSWP
O
VR
W
890606,
891102,
900314
940117 B.05.00
B.02.00,
B.02.01,
B.03.00
PA 850730 A.00.01
PADC 870501 A.03.00
PATHLOCK 850730 A.00.01
PAUSE 850730 A.00.01
PC 940117 B.05.00
PCDELTA 940117 B.05.00
PD 850730 A.00.01
PDA 850730 A.00.01
PDF 850730 A.00.01
PDMEAS 920325, 920527 B.04.021, B.04.03
PEAKS 850730 A.00.01
PEN 850730 A.00.01
PERASE 880314 B.00.00
PERSIST 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
PINPUT 850730 A.00.01
PLOT 850730 A.00.01
POSU 850730 A.00.01
PO
WER
ON
850730 A.00.01
PP 861015 A.02.00
PR 860203 A.01.00
PREAMP 880314 B.00.00
PREFX 890606,
PR
OCEDURE
PR
OGDEF
891102,
900314
850730 A.00.01
901008 B.03.01
B.02.00,
B.02.01,
B.03.00
PROTECT 861015 A.02.00
PRSDAC 861015 A.02.00
PRSENABL 861015 A.02.00
PRSHYST 861015 A.02.00
PSDAC 861015 A.02.00
PSENABLE 861015 A.02.00
PSHYST 861015 A.02.00
PSTATE 850730 A.00.01
PTBL 870501 A.03.00
PTEL 870501 A.03.00
PTTIMEOUT 920325, 920527 B.04.021, B.04.03
PU 850730 A.00.01
PURGE 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
PWRAVG 940117 B.05.00
1
The rmware with V.U.F code B.04.02 did not ship in the HP 70900B lo cal
oscillator source. This rmware was only shipp ed in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
Remote Commands/Date Codes/V.U.F Codes 3-11
Command Date Code V.U.F Code
PWRBAR 910802,
PWRBAR
ON
910802,
911021
911021
B.04.00,
B.04.00,
B.04.01
B.04.01
PWRBW 850730 A.00.01
PWRMODE 910802,
911021
B.04.00,
B.04.01
R1 901008 B.03.01
R2 901008 B.03.01
R3 901008 B.03.01
R4 901008 B.03.01
RB 850730 A.00.01
RBR 850730 A.00.01
R
R
R
C
CLD
CLS
890606,
860203 A.01.00
891102,
900314
B.02.00,
B.02.01,
850730 A.00.01
B.03.00
RCLT 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
RCLU 880314 B.00.00
RCVRMODE 940117 B.05.00
READMENU 850730 A.00.01
RELADC 940117 B.05.00
RELHPIB 850730 A.00.01
RELMOD 940117 B.05.00
REPEAT 850730 A.00.01
RETURN 850730 A.00.01
REV 850730 A.00.01
RL 850730 A.00.01
RLPOS 850730 A.00.01
RMS 850730 A.00.01
R
OFFSET
850730 A.00.01
RQS 850730 A.00.01
RSPSVTY 910802, 911021 B.04.00, B.04.01
S1 860203 A.01.00
S2 860203 A.01.00
SAVED 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
SAVES 850730 A.00.01
SAVET 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
SAVEU 880314 B.00.00
SCALE 850730 A.00.01
SENS 910802, 911021 B.04.00, B.04.01
SER 850730 A.00.01
SG 940117 B.05.00
SIGDEL 850730 A.00.01
3-12 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
SIGID 850730 A.00.01
SMOOTH 850730 A.00.01
SNGLS 850730 A.00.01
SP 850730 A.00.01
SP 910802, 911021 B.04.00, B.04.01
SQR 850730 A.00.01
SRCALC 860203 A.01.00
SRCAM 860203 A.01.00
SR
CAMF
SR
CA
SR
CBLNK
T
860203 A.01.00
860203 A.01.00
860203 A.01.00
SRCMOD 860203 A.01.00
SRCOSC 860203 A.01.00
SRCPOFS 860203 A.01.00
SRCPSTP 860203 A.01.00
SRCPSWP 860203 A.01.00
SRCPWR 860203 A.01.00
SRCTK 860203 A.01.00
SR
CTKPK
SR
Q
860203 A.01.00
850730 A.00.01
SS 850730 A.00.01
ST 850730 A.00.01
STA 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
STARTUP 940117 B.05.00
ST
A
TE
850730 A.00.01
STB 850730 A.00.01
STDEV 850730 A.00.01
STOR 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
STORREF 860203 A.01.00
SUB 850730 A.00.01
SUM 850730 A.00.01
SUMSQR 850730 A.00.01
SV 860203 A.01.00
SW 901008 B.03.01
SWEEP 910802, 911021 B.04.00, B.04.01
SWPMODE 940117 B.05.00
SWPMODE? 940117 B.05.00
SYSCOR 910802, 911021 B.04.00, B.04.01
T0 860203 A.01.00
T1 901008 B.03.01
Remote Commands/Date Codes/V.U.F Codes 3-13
Command Date Code V.U.F Code
T2 901008 B.03.01
T3 901008 B.03.01
T4 901008 B.03.01
TA 901008 B.03.01
TB 901008 B.03.01
TDF 850730 A.00.01
TEST 850730 A.00.01
TEXT 850730 A.00.01
TH 850730 A.00.01
THE 901008 B.03.01
THEN 860203 A.01.00
THREED 920325, 920527 B.04.021, B.04.03
THREEDH 920325, 920527 B.04.021, B.04.03
THREEDV 920325, 920527 B.04.021, B.04.03
TIME 860203 A.01.00
TITLE 850730 A.00.01
TM 850730 A.00.01
TP 850730 A.00.01
TR 890606, 891102, 900314 B.02.00, B.02.01, B.03.00
TRA 860203 A.01.00
TRB 860203 A.01.00
TR
TR
C
COND
860203 A.01.00
850730 A.00.01
TRDEF 850730 A.00.01
TRDSP 850730 A.00.01
TRIGDEL 940117 B.05.00
TRPRST 861015 A.02.00
TRPST 850730 A.00.01
TRST
A
T
850730 A.00.01
TS 850730 A.00.01
TWINDOW 850730 A.00.01
UNTIL 860203 A.01.00
UR 901008 B.03.01
USERERR 850730 A.00.01
USERKEY 850730 A.00.01
USERLOCK 861015 A.02.00
USERMSG 861015 A.02.00
USERWARN
940117 B.05.00
USRPWR 910802, 911021 B.04.00, B.04.01
USTATE 850730 A.00.01
1
The rm
ware with V.U.F co de B.04.02 did not ship in the HP 70900B lo cal
oscillator source. This rmware was only shipp ed in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
3-14 Remote Commands/Date Codes/V.U.F Codes
Command Date Code V.U.F Code
V
ARDEF
850730 A.00.01
VARIANCE 850730 A.00.01
VAVG 850730 A.00.01
VB 850730 A.00.01
VBO 901008 B.03.01
VBR 850730 A.00.01
VIEW 850730 A.00.01
VTDL 940117 B.05.00
VTH 850730 A.00.01
VTL 850730 A.00.01
VW 850730 A.00.01
WAIT 850730 A.00.01
WARN 940117 B.05.00
WARN? 940117 B.05.00
W
ARNCTRL
940117 B.05.00
XAMPSW 920325, 920527 B.04.021, B.04.03
X
XD
CH
A
C
850730 A.00.01
910802,
911021
B.04.00,
B.04.01
XERR 850730 A.00.01
XNOISE 890606,
XW
ARN
891102, 900314
940117 B.05.00
B.02.00,
B.02.01, B.03.00
XYPEAK 910802, 911021 B.04.00, B.04.01
YD
A
C
910802,
911021
B.04.00,
B.04.01
YLABELS 940117 B.05.00
ZOOMRB 880314 B.00.00
1
The rmware with V.U.F code B.04.02 did not ship in the HP 70900B lo cal
oscillator
source.
This
rm
w
are
w
as
only
shipp
ed
in the HP 70950A optical
spectrum analyzer and HP 70951A optical sp ectrum analyzer.
Remote Commands/Date Codes/V.U.F Codes 3-15
Loading...