How it Works
Agilent
Loading...
6843A
Data Sheet
3 pgs47.09 Kb0
User’s Guide
79 pgs393.32 Kb0

Agilent 6843A Data Sheet

Download
Page 1
6811B 6812B 6813B 6814B 6834B 6843A
Number of Phases 1 1 1 1 1/3 1 RMSVoltage 0.15% + 0.3 V 0.15% + 0.3 V 0.15% + 0.3 V 0.15% + 0.3 V 0.15% + 0.3 V 0.15% + 0.3 V
(% of output + offset) (45 - 100Hz) (45 - 100Hz) (45 - 100Hz) (45 - 100Hz) (45 - 100Hz) (45 - 100Hz)
0.5% + 0.3 V 0.5% + 0.3 V 0.5% + 0.3 V 0.5% + 0.3 V 0.5% + 0.3 V 0.5% + 0.3 V (>100 - 500 Hz) (>100 - 500 Hz) (>100 - 500 Hz) (>100 - 500 Hz) (>100 - 500 Hz) (>100 - 500 Hz) 1% + 0.3 V 1% + 0.3 V 1% + 0.3 V 1% + 0.3 V 1% + 0.3 V 1% + 0.3 V (> 500 - 1000 Hz) (> 500 - 1000 Hz) (> 500 - 1000 Hz) (> 500 - 5000 Hz) (> 500 - 5000 Hz) (> 500 - 1000 Hz)
(6834B only) 1˚ (>100 - 1kHz)
1˚ + 1˚/ kHz (>1 kHz - 5kHz)
(per phase for a sine wave with a resistive load at 0º to 40º C, within an output frequency range of 45 Hz to 1000Hz, and in ac coupled mode after a 30 minute warm-up unless otherwise noted. Note: For 6814B, 6834B and 6843A output voltage must be at least 50% of range.)
1
SPECIFICATIONS (CONTINUED)
(per phase for a sine wave with a resistive load at 0º to 40º C, within an output frequency range of 45 Hz to 1000Hz, and in ac coupled mode after a 30 minute warm-up unless otherwise noted. Note: For 6814B, 6834B and 6843A output voltage must be at least 50% of range.)
1
SPECIFICATIONS
6811B 6812B 6813B 6814B 6834B 6843A
Number of phases 1 1 1 1 1/3 1 Output ratings Power 375 V A 750 VA 1750 VA 3000 VA 4500 VA/1500 VA 4800 VA
rms voltage 300 V 300 V 300 V 300 V (high range) 300 V (high range) 300 V (high range)
150 V (low range) 150 V (low range) 150 V (low range)
rms current 3.25 A 6.5 A 13 A
2
10 A (300 V range)215 A/5 A (300 V range) 16A (300 V range)
2
20 A (150 V range)230 A/10 A (150 V range) 32A (150 V range)
Repetitive & non-repetitive 40 A 40 A 80 A 40 A (300 V range) 60 A/20A (300 V range) 48 A (300 V range) peak current 80 A (150 V range)
120 A/40 A (150 V range)
96 A (150 V range)
Crest factor 12 6 6 4 4 3 Load Power factor 0 to 1 0 to 1 0 to 1 0 to 1 0 to 1 0 to 1
capability dc power 285 W 575 W 1350 W N/A N/A N/A dc voltage ±425 V ±425 V ±425 V N/A N/A N/A dc current 2.5 A 5.0 A 10.0 A N/A N/A N/A
Output frequency dc; 45Hz to dc; 45Hz to dc; 45 Hz to 45Hz to 5 kHz 45 Hz to 5 kHz 45 Hz to 1 kHz range 1 kHz 1 kHz 1 kHz
Constant voltage (20 kHz to 10 MHz) -60 dB (relative -60 dB (relative -60 dB (relative -60 dB (relative -60 dB (relative -60 dB (relative rippleand noise to full scale) to full scale) to full scale) to full scale) to full scale) to full scale)
Line regulation (% of full scale) 0.1% 0.1% 0.1% 0.1% 0.1% 0.1% Load regulation (% of full scale) 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% Maximum total 0.25% at 50/60Hz 0.25% at 50/60Hz 0.25% at 50/60Hz 1% (45-1000Hz) 1% (45-1000Hz) 1% (45-1000 Hz)
harmonic distortion 1% worst case 1% worst case 1% worst case 1% + 1%/kHz 1% + 1%/kHz 1% + 1%/kHz
45 to 1 kHz 45 to 1 kHz 45 to 1 kHz (>1 kHz - 5 kHz) (>1 kHz - 5 kHz) (>1 kHz - 5 kHz)
Programming accuracy (25˚±5˚ C)
44 AGILENT ac POWER SOLUTIONS
ac Power Solutions (cont’d)
Visit our web site
http://www.agilent.com/find/power
A
B
C
D
E
F
H
ac Power Solutions
(Maximum)
For a complete list of specifications for Agilent’s ac power solutions, please see the operating manual on our web site at http:// www.agilent.com/find/manuals
Page 2
For more information in the U.S.A. call
1-800-452-4844
AGILENT ac POWER SOLUTIONS 45
ac Power Solutions (cont’d)
A
B
C
D
E
F
H
ac Power Solutions
6811B 6812B 6813B 6814B 6834B 6843A
Rms. voltage (45 - 100 Hz)
0.03% + 100 mV
3
0.03% + 100 mV
3
0.03% + 100 mV
3
0.05% + 250 mV 0.05% + 250 mV 0.05% + 250 mV
dc Voltage 0.05% + 150 mV
3
0.05% + 150 mV
3
0.05% + 150 mV
3
N/A N/A N/A
RMSCurrent (45 - 100 Hz)
4
high range 0.05% + 10 mA 0.05% + 10 mA 0.05% + 10 mA 0.1% + 50 mA 0.1% + 50 mA (1) 0.1% + 50 mA
0.1% + 25 mA (3)
low range 0.05% + 1.5 mA 0.05% + 1.5 mA 0.05% + 1.5 mA N/A N/A N/A
Power (VA) (45-100 Hz)
4
0.1% + 1.5 VA + 0.1% + 1.5 VA + 0.1% + 1.5 VA + 0.15% + 5 VA 0.15% + 5 V A (1) 0.15% + 9 VA
high range 12 mVA/V 12 mVA/V 12 mVA/V 0.15% + 3 VA (3) low range
0.1% + 1.5 VA 0.1 % +1.5 VA 0.1% + 1.5 V A N/A N/A N/A +1.2 mVA/V +1.2 mVA/V +1.2 mVA/V N/A N/A N/A
Power (watts) (45-100 Hz)
4
0.1% + 0.3 W + 0.1% + 0.3 W + 0.1% + 0.3 W + 0.15% + 5 W 0.15% + 5 W (1) 0.15% + 9 W high range 12 mW/V 12 mW/V 12 mW/V N/A 0.15% + 3 W (3) low range 0.1% + 0.3 W + 0.1% + 0.3 W + 0.1% + 0.3 W + N/A N/A N/A
+1.2 mW/V +1.2 mW/V +1.2 mW/V N/A N/A N/A
Frequency 0.01% + 0.01 Hz 0.01% + 0.01 Hz 0.01% + 0.01 Hz 0.01% + 0.01 Hz 0.01% + 0.01 Hz 0.01% + 0.01 Hz Power Factor 0.01 0.01 0.01 0.01 0.01 0.01
Output frequency range N/A 50 /60 Hz 50 /60 Hz N/A N/A 50 /60 Hz Reference impedence N/A
3% (at 0.4 Ωand 796 mH) 3% (at 0.4 Ω and 796 mH)
N/A N/A
3% (at 0.4 Ωand 796 mH)
accuracy 1% (at 0.4 Ωand 796 1% (at 0.4 Ωand 796
1% (at 0.4 Ωand 796
m
H at 25˚)
m
H at 25˚)
m
H at 25˚)
Output voltage harmonic
N/A
Compliant withIEC 868 Compliant with IEC 868 N/A N/A Compliant with IEC 868
content
6
and IEC 61000-3-2 and IEC 61000-3-2 and IEC 61000-3-2
Current magnitude Fundamental 0.03% + 1.5 mA 0.03% + 1.5 mA N/A N/A 0.03% + 3 mA
(low range) Harmonics 2-49
0.03% + 1mA + 0.2%/kHz 0.03% + 1mA + 0.2%/kHz
0.03% + 2 mA + 0.2%/kHz
Current magnitude Fundamental 0.05% + 5 mA 0.05% + 5 mA N/A N/A 0.05% + 6 mA
(high range) Harmonics 2-49
0.05% + 3 mA + 0.2%/kHz 0.05% + 3 mA + 0.2%/kHz 0.05% + 3 mA +
0.2%/kHz
Flicker N/A Compliant with IEC 868 Compliant with IEC 868 N/A N/A Compliant with IEC 868 Flicker Perceptibility (PST) N/A Compliant with IEC 868 Compliant with IEC 868 N/A N/A Compliant with IEC 868 Synchronization accuracy N/A <1ppm <1ppm N/A N/A <1ppm Current shunt burden N/A 0 volts 0 volts N/A N/A 0 volts Current harmonic N/A 1.5 seconds 1.5 seconds N/A N/A 1.5 seconds
smoothing filter time constant
Pst integration time N/A 1, 5, 10 or 15 minutes 1, 5, 10 or 15 minutes N/A N/A 1, 5, 10 or 15 minutes
Notes:
1
It is possible to program the output frequency of the 6812B and 6813B from dc to 45 Hz (please see note 3).
2
Full current is available at voltages between 50% and 100% of the output voltage range.
3
Product may be operated between dc and 45 Hz subject to the following conditions:
Measurements may be extended to 4.5 Hz at full accuracy only by selecting a digitization rate of 250 µ seconds per point Frequency content of the measured signal must be limited to 4 k Hz or less to avoid aliasing effects
4
Select low measurement range for improved accuracy (10:1) for lower power measurements.
5
Single-phase operation.
6
Output voltage harmonic content specification is limited for the 6843A for half-wave rectified/Class C loads. Compliance will be tested, verified and reported by the RTS software for all Devices Under Test
Sample Rate Window Width Acquisition Overlap
50 Hz Operation
Rectangular measurement window 12.8 kHz 16 cycles None
Hanning measurement window 8.533 kHz 24 cycles 50%
50 Hz Operation
Rectangular measurement window 15.360 kHz 16 cycles None
Hanning measurement window 7.680 kHz 24 cycles 50%
(per phase for a sine wave with a resistive load at 0º to 40º C, within an output frequency range of 45 Hz to 1000Hz, and in ac coupled mode after a 30 minute warm-up unless otherwise noted. Note: For 6814B, 6834B and 6843A output voltage must be at least 50% of range.)
1
SPECIFICATIONS (CONTINUED)
Measurment accuracy
IEC Mode Measurement System Characteristics
Regulatory Test Solutions IEC mode measurement system characteristics (6812B, 6813B and 6843A only)
Measurement accuracy (25˚±5˚ C)
Page 3
Visit our web site
http://www.agilent.com/find/power
ac Power Solutions
46 AGILENT ac POWER SOLUTIONS
ac Power Solutions (cont’d)
6811B 6812B 6813B 6814B 6834B 6843A
Average programmingaccuracy
(% of output + offset) rms current 1.2% + 50 mA 1.2% + 50 mA 1.2% + 50 mA 0.2% + 80 mA 0.2% + 80 mA (1) 0.2% + 80 mA
0.2% + 40 mA (3)
Average programmingresolution
rms voltage 125 mV 125 mV 125 mV 80 mV 80 mV 80 mV
dc voltage 250 mV 250 mV 250 mV N/A N/A N/A
Overvoltage programming (OVP) 2 V peak 2 V peak 2 V peak 2 V peak 2 V peak 2 V peak
rms current 2 mA 4 mA 4 mA 5 mA
7.5 mA (1), 2.5 mA (3)
7.5 mA
peak current 12.5 mA 25 mA 25 mA N/A N/A N/A
output frequency 10 µHz 10 µHz 10 µHz 10 µHz 10 µHz 10 µHz
phase N/A N/A N/A N/A N/A N/A
Average measurementresolution
rms voltage 10 mV 10 mV 10 mV 10 mV 10 mV 10 mV rms current 2 mA 2 mA 2 mA 3 mA 2 mA (1)/6 mA (3)6 mA
Programmable output impedance
resistance 0-1
Ω
0-1
Ω
0-1
Ω
N/A N/A N/A
inductance 20 µh - 1 mh 20 µh - 1 mh 20 µh - 1 mh N/A N/A N/A
Remote sense capability Up to 1 Vrms can be dropped Up to 10 Vrms can be dropped
across each load lead. across each load lead.
Isolation to ground 300 Vrms/425 Vdc 300 Vrms/425 Vdc 300 Vrms/425 Vdc 300 Vrms 300 Vrms 300 Vrms Net Weight 28.2 kg (62 lb) 28.2 kg (62 lb) 32.7 kg (72 lb) 79.5 kg (175 lb) 87.7 kg (193 lb) 87.7 kg (193 lb) Shipping Weight 31.8 kg (70 lb) 31.8 kg (70 lb) 36.4 kg (80 lb) 119.1 kg (262 lb) 127.3 kg (280 lb) 127.3 kg (280 lb)
Dimensions See drawings on page 54 See drawings on page 55
(non-warranted characteristics determined by design that are useful in applying the product)
SUPPLEMENTAL CHARACTERISTICS
ac I
NPUT RATINGS
6811B 6812B 6813B 6814B 6834B 6843A
Voltage range (Vac) 87 to 106 V ac 87 to 106 Vac 174 to 220 V ac *180 to 235 L-L (3) *180 to 235 L-L (3) *180 to 235 L-L (3)
*default factory setting *104 to 127 Vac *104 to 127 Vac *191 to 254 Vac
360 to 440 L- L (3) 360 to 440 L-L (3) 360 to 440 L-L (3)
174 to 220 Vac 174 to 220 Vac
(requires option 400) (requires option 400) (requires option 400)
191 to 254 Vac 191 to 254 Vac
Maximum input current (rms)
1
12 A (100 Vac) 28 A (100 V ac) 22 A (200/208 V ac) 18 A (208 Vac) 24 A (208 Vac) 24 A (208 Vac) 10 A (120 Vac) 24 A (120 V ac)
7.5 A (200/208 Vac) 15 A (200/208 Vac) 20 A (230 Vac) 10 A (380 Vac) 15 A (380 Vac) 15 A (380 V ac)
6.5 A (230 Vac) 13 A (230 V ac)
Input power (max)
2
1000 VA/700 W 2500 VA/1400 W 3800 V A/2600 W 5800 VA/4100 W 8900 VA/5900 W 8900 VA/5900 W
Input frequency 47 to 63 Hz 47 to 63 Hz 47 to 63 Hz 47 to 63 Hz 47 to 63 Hz 47 to 63 Hz
1
Measured at low line 2Measured at high line 3Measured at high line
Ordering Information
Opt 001
Harmonic and Flicker EmissionsT est (6812B,6813B, 6843A only)
Opt 002 Voltage and Frequency Disturbances Immunity Test
(6812B, 6813B, 6843A only)
Opt 003
Interharmonics Immunity Test (6812B, 6813B, 6843A only)
Opt 009 All the RTS software (6812B, 6813B, 6843A only) Opt 0BN
Service Manual, extra Operating Guide, and
+$35
ProgrammingGuide
Opt 1CMRack-mount Kit, p/n 5062-3977 (quantity 2) +$40
(support rails required)
E3664AC Cabinet Rails must be
ordered when rack mounting the 6814B and 6834B Opt 1CM
Opt 1CP
Rack-mount Kit with Handles, p/n 5062-3983 +$90
(support rails required) 6811B, 6812B, 6813B only
Support rails, p/n 12679B, required when rack mounting the 6811B, 6812B, and 6813B Opt 1CM and Opt 1CP
Opt 10087 to 106 Vac, 48 to 63 Hz input (6811B, 6812B only)
Japan only
Opt 200174-220 Vac, 48-63 Hz input (6813B only) Japan only Opt 230191 to 254 Vac, 48-63 Hz input (6811B, 6812B only) Opt 400360 to 440 Vac, 3-phase, 47 to 63 Hz input (6814B,
6834B, 6843A only) required for Europe
Opt 831
12 AWG, 200 to 240 Vac, unterminated (6812B,6813B only)
Opt 8324 mm
2
wire size, unterminated (6813B only)
Opt 8331.5 mm
2
wire size, 200 to 240 Vac, unterminated
(6812B only)
Opt 83410 AWG, 100 to 120 V ac, unterminated (6812B only) Opt 841Line Cord with NEMA L6-20P; 20 A 250 V Plug (6812B
only)
Opt 842Line Cord with IEC 309; 32 A 220 V plug (6813B only) Opt 844Line Cord with NEMA L6-30P; 30 A 250 V Locking Plug
(6813B only)
Opt 845Line Cord with IEC 309; 16 A 220 V Plug (6812B only) Opt 846Line Cord with NEMA L6-30P; 30 A 120 V Plug
(6812B only)
Opt 847Line Cord with CEE 7/7; 16 A 220 V Plug (6812B only) Opt 848Line Cord with BS 546; 15 A 240 V Plug (6812B only)
For ac Line Cord and Cord Options information see pages 44-47. For Dimension Drawings see pages 58 and 59.
6814B and 6834B Accessories $9,500
p/n 5060-3513Three 30 A replacement fuses
for 180 to 440 Vac line +$35
p/n 5063-2310 Heavy duty rack slide kit +$90
A
B
C
D
E
F
H
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use