Page 1
ASSEMBLY
PLANTING
STARTING
Simple Steps
English
To Get Your
Classic
Up and Growing
Quick Start Guide
KEEP THIS GUIDE!
N. American Model #s:
100710-BLK; 100710-WHT; 100710-SLR
Input Voltage: 115V, 60Hz, 1.5A
EU & Australia Model #s:
200710-BLK; 200710-WHT; 200710-BKG; 200710-WTG;
500710-BLK; 500710-WHT; 500710-SLR
Input Voltage: 220-240V, 50Hz, 0.75A
Date Code:
Page 2
IMPORTANT SAFETY INSTRUCTIONS
(SAVE THESE INSTRUCTIONS)
When using this AeroGarden electrical furnishing, basic precautions should always be followed,
including the following:
Read all instructions before using this AeroGarden furnishing.
1. To reduce the risk of electric shock, the AeroGarden has a specific plug. Do not change plug in any way.
DANGER – to reduce risk of electric shock:
2. Always unplug AeroGarden from electrical outlet before cleaning or changing Grow Bulbs (light bulbs).
WARNING – to reduce risk of burns, fire, electric shock, or injury to persons:
3. Unplug AeroGarden from outlet before putting on or taking off parts.
4. Close supervision is necessary when AeroGarden is used by or near children, invalids, or disabled persons.
5. Use AeroGarden only for its intended use as described in the instructions. Do not use attachments not recommended by
manufacturer.
6. Never operate AeroGarden if it has a damaged cord or plug, if it is not working properly, if it has been dropped and damaged, or if it has been dropped in water. If any of these conditions occur/exist, contact www.aerogardensupport.com or your
country’s local distributor for instructions.
7. Keep cord away from heated surfaces.
8. Never operate furnishing with air openings blocked. Keep air openings free of lint, hair, and the like.
9. Never drop or insert any object into any electrical openings.
10. Do not use outdoors.
11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12. Do not touch moving parts or hot parts such as pumps, bulbs, reflective surfaces, and the like.
13. To disconnect, remove plug from outlet.
14. Do not place or submerse base, cord, plug, or lamp hood in water or other liquid to clean it.
15. Do not allow water to contact hot light bulbs.
16. Use only approved and supplied parts and accessories. Use only lamp model 100629 (N. America) or 200629 (Europe &
Australia) Grow Bulbs with this AeroGarden model.
parts can be ordered from www.aerogardensupport.com or from your retailer.
17. Do not use AeroGarden for other than intended purpose.
18. This product is intended for household and residential use only. This product is not approved for commercial applications.
19. Read and follow all important notices on the AeroGarden and in the accompanying literature.
20. If supply cord is damaged, it must be replaced by manufacturer, its service agent, or similarly qualified technician in order to
avoid a hazard.
21. Electrical wiring must be in accordance with local regulations.
22. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of appliance by
a person responsible for their safety.
23. Children should be supervised to ensure they do not play with the appliance.
Use of any other kind of accessory is not recommended. Replacement
1
SAVE THESE INSTRUCTIONS
Page 3
Wonderful Plants
Seed Kit
1
Quick Start Assembly (No tools required)
Unpack Your AeroGarden
A
Lamp Hood
(front view)
Bowl
Base
(front view)
Lamp Arm
(back view)
Insert Lamp Arm
B
into Base
Push
Lamp Arm
down until
you hear
a “click.”
Lamp Arm
(back view)
Base
(back view)
C
Grow Bulbs (2)
Seed Kit
Insert Grow Bulbs
into Lamp Hood
Lamp Hood
(bottom view)
Push straight in.
DO NOT TWIST BULBS!
Remember to replace Grow Bulbs every 6 months.
D
Plug Lamp Cord
into Lamp Hood
Push Lamp Cord
firmly into socket
in Lamp Hood.
Lamp
Cord
Instructions Continued On Next Page
2
Page 4
1
Quick Start Assembly (continued)
Place Lamp Hood
E
on Lamp Arm
Center hands over
Lamp Arm and push
Lamp Hood down until
you hear a “click.”
(back view)
F
Set Bowl into Base
(front view)
Check to be sure that Bowl
is securely in place.
G
Moving Your AeroGarden
Use one hand to
grasp Lamp Arm.
Gently slide AeroGarden
toward the surface edge and
place other hand under Base.
NEED ADDITIONAL HELP?
For supplies and information, visit…
www.aerogardensupport.com
3
Page 5
Wonderful Stuff
Place Your Garden
H
In: A 60-75°F
(16-24°C)
environment
(optimal)
On: A sturdy, watertolerant surface
(Metal surfaces may cause
noise due to vibration)
Under: A space that
allows 22” (56cm)
clearance for the full
height of raised lamp
Away From
Near: A standard
electrical outlet, per
local regulations
68°F/20°C
Note: Do not place beneath
under-cabinet lights.
Reach of children and pets
Direct sources of heat (e.g., stove, furnace vents)
Direct sources of cold air (e.g., window drafts, A/C vents)
For Optimal Tending & Harvesting, Also Consider
Easy access to un-softened water
4
Page 6
2
A
When additional water is needed, “Water Level Low” light on Control Panel will blink.
Add water to raise level up to “Fill To Here” inside Bowl.
It is okay to add water up to “Fill To Here” before “Water Level Low” light blinks.
Planting Your Garden
Add Water Using a Spouted Container
Use room temperature municipal tap, bottled or
purified water. Do not use well or softened water.
Lift
View Door
Fill to “Fill To Here”
(located inside the Bowl)
Amount of
Water To Be
Added:
3.5 quarts or...
3.2 liters
B
Plant Your Garden
Insert Seed Pods into Grow Surface openings.
Check to see that…
• Seed Pods are in the same position in Grow
Surface as they were in Seed Kit Tray.
• Seed Pod Labels are facing forward.
• Seed Pods are pressed firmly in place.
Seed Pod
Bio-Domes
Nutrients
™
Grow Surface
Seed Kit Tray
5
Page 7
Place Bio-Domes on Seed Pods
C
Place a Bio-Dome on
each Seed Pod.
Press Bio-Dome down
until its rim almost
touches Grow Surface.
Bio-Dome
Note: Do not remove Bio-Domes until seeds
have sprouted. NEVER REMOVE SEED
POD LABELS.
Add Starting Nutrient Tablets and Record Planting Date
D
Record Planting Date
Record the date you planted your AeroGarden
on the front cover of the Guide that came with
your Seed/Plant Kit.
Add 2 tablets from
“Starting Nutrients”
bag directly into Bowl.
See "Add Nutrients" (Feed Garden - Basic Feeding) on
page 10 of this guide for additional feeding instructions.
6
Page 8
3
A
Starting Your Garden
Plug Cord into Electrical Outlet
What will happen...
A green light on the Smart Garden
Control Panel will light up.
Plug in
View Door
Grow Bulbs will come on.
Look under Lamp Hood to see if both bulbs are lit.
If not, check to see if:
• Grow Bulbs are properly inserted in Lamp Hood
(page 2, step 1C).
• Lamp Cord is plugged into Lamp Hood (page 2, step 1D).
• You are getting power through the electrical outlet.
When Pump starts* it may make a gurgling noise for a moment.
Lift View Door. You should see water dripping from the bottom
of Seed Pods into the Bowl.
If not, check to see if:
• Lamp Arm is fully inserted into Base (page 2, step 1B).
• Bowl is firmly seated on Base (page 3, step 1F).
*Pump may take up to twelve hours to start.
7
Note: You will hear water flowing until plant roots have grown to surface level of water
(a few weeks). Keeping water level in Bowl up to “Fill To Here” will help reduce the
sound of dripping water.
Page 9
Select Plant Type
B
Press the SELECT button until you reach the type of plant you are growing
(Tomatoes/Peppers, Salad Greens, etc.).
Note: Depending on the plant type selected, your
AeroGarden pump will automatically turn on and
off at pre-programmed intervals. Pump controls
the flow of water through Seed Pods to optimize
plant growth.
Your Light Timer
C
Your Light Timer is Set To Start Growing
1
Your Plants...Starting Now!
If You Would Like to Change the Time
2
• Your lights will stay on for about 16 hours and will shut off for about 8 hours.
• Your lights will come on every day at the time you plugged in your AeroGarden.
of Day Your Lights Will Go Off...
See “Personalize Your Light Timer” on page 9.
8
Page 10
Personalize Your Light Timer (optional)
Your AeroGarden has lights and a built-in timer that automatically provide plants with the optimal amount of “sunlight”
(about 16 hours) and “night” (about 8 hours), depending on the plant type selected in the previous section.
As long as plants get this amount of light, it does not matter when the lights are turned off.* Many people find it con-
venient to have the lights go on in the morning and off at night to match their own wake and sleep schedule.
*The exceptions to this are Flower, Tomato & Pepper plants. They require a daily dark period in order to produce flowers. If your plants will receive
any room light during the day (natural or artificial), we recommend that you set your AeroGarden lights to be on during the day.
5 Simple Steps...
In order to make this as simple as possible, you only
need to set the time you want your AeroGarden
Do the following to set the time you want your lights to go off:
Decide what time of day you want the lights to go OFF.
1
AT THAT TIME check that lights are on. If they are off, quickly press “Lights” button and
2
immediately release. (Lights must be on in order to reset timer.)
With lights on, press and hold “Lights” button until the green light next to the plant type
3
you selected starts blinking – about 5 seconds.
Release the button.
4
When blinking stops (about 9 seconds), the lights will go off.
5
Your lights are now set to go off at this time every day.
lights to go off (Off Time), and your built-in light
timer automatically sets the On Time...nothing
more for you to do.
Lights Button
Now, each day, your AeroGarden lights will automatically
• Turn Off at the time you set using the above steps
• Remain off for about 8 hours
• Turn on for about 16 hours
You can reset your timer as often as you want.
If light from your AeroGarden is visible from
your bedroom, you may want to set the lights to
go off about the time you usually go to bed, so
as not to disturb your sleep.
9
Blinking Light
In case of power failure, your AeroGarden has a backup
system that stores your light & nutrient timers and plant
selection settings. When power is restored, your AeroGarden
will go back to the Off-On cycle you have set.
(if you selected Salad Greens)
Page 11
Basic Reminders About Your AeroGarden
AeroGarden Classic Control Panel Features
• Add Nutrients (Feed Garden - Basic Feeding)
When “Add Nutrient” and “Water Level Low” lights start
• Water Level Low
When light blinks add
water up to “Fill to Here.”
blinking (every 2 weeks), add 2 nutrient tablets* and fill the Bowl
with water up to “Fill to Here.” Press and release the “Reset”
button to restart nutrient timer and turn off blinking lights.
*See Tending & Harvesting Guide for plant-specific nutrient information.
• Lights On/Off
Use to occasionally override built-in light timer. Once
pushed, lights will stay off/on until the next time built-in
light timer is set to go on/off. This will not affect the timing
of your light cycle and occasional use of this feature will
not harm your plants.
Remember: Grow Bulbs should be replaced every 6 months – order
replacement bulbs at www.aerogardensupport.com or from your retailer.
• Remove Bio-Domes
When plants appear through the
hole in Seed Pod Labels, remove
Bio-Domes and discard or recycle.
NOTE: Never remove Seed Pod Labels.
10
Page 12
Basic Reminders About Your AeroGarden
(continued)
Raise Lamp Hood (Lights)
As plants grow to 1-2” from lights, raise Lamp Arm one Locking Button at a time. Be sure Lamp Arm is
set on the lowest Locking Button when you start your AeroGarden.
3
Raise Lamp Arm/Lamp Hood
1
Unplug AeroGarden.
2
Remove Bowl from Base.
by holding Lamp Arm & Hood
with one hand, and pushing in
Locking Button with the other.
Push Locking
Button in
Replace Bowl on Base.
4
Plug in AeroGarden.
5
Replace Grow Bulbs
It is important to keep track of how long your Grow Bulbs have been in use and replace them every
6 months. After 6 months of use, the quality of light from the Grow Bulbs in your AeroGarden begins
to degrade. This happens with all full-spectrum fluorescent bulbs, and is a critical issue when growing
plants. In order for plants to be healthy and productive, they must receive the appropriate intensity and
spectrum of light.
How To Replace Grow Bulbs…
• Unplug AeroGarden.
• Remove old Grow Bulbs and carefully discard*.
IMPORTANT: To avoid burning, be sure Grow Bulbs
are cool before handling.
• Insert new Grow Bulbs into Lamp Hood.
• Plug in AeroGarden.
*Check with local recycling authorities for light bulb
recycling availability in your area.
Order replacement bulbs at
www.aerogardensupport.com or from your retailer.
11
Page 13
Prepare For Your Next Garden
Cleaning and Storage Instructions for your AeroGarden
When your garden has completed its growing cycle…
1
Unplug AeroGarden.
2
Carefully remove Bowl and
Grow Surface from the Base
and bring to a sink.
Set Base and Lamp Hood aside.
NEVER SUBMERSE BASE AND
CONTROL PANEL IN WATER.
Remove Grow Surface from
3
Bowl and place on a counter
near a sink.
4
Empty contents of Bowl in sink.
5
Remove Seed Pods and plants
from Grow Surface.
• Pull Seed Pods out of Grow
Surface openings.
• Throw away Seed Pods and
plant debris (plant growth and
roots). If you compost, plant
debris can be composted.
Rinse and clean Grow Surface,
6
Pump Stand and Pump Filter*.
• Use a soft scrub brush to clean
tangled roots from underside of
Grow Surface and Pump Stand.
• Remove Pump Filter from
Pump Stand. Gently scrub
roots from Pump Filter.
• Place Pump Filter back into
Pump Stand.
After cleaning, there may still be a few
roots in your Grow Surface, Pump Stand
or Pump Filter. This will not affect the
operation of your AeroGarden.
Pump
Stand
Lamp
Hood
Grow
Surface
Bowl
Plant
Growth
Seed
Pod
Roots
Base
Grow
Surface
Pump
Filter
7
Sanitize AeroGarden.
• Fill Bowl ¾ full with water.
¼
• Add
cup (59ml) of chlorine
bleach.
• Replace Grow Surface on Bowl,
place Bowl on Base and plug in
AeroGarden for 1-2 minutes.
(Select Salad Greens on Control
Panel to be sure water is flowing.)
• Unplug AeroGarden and empty
bleach water from Bowl.
8
Rinse AeroGarden.
• Rell Bowl with tap water and
replace on Base.
• Plug in and run AeroGarden
for 1-2 minutes. (Select Salad
Greens again.)
• Empty Bowl and repeat this step
(step 8) one more time.
9
Towel dry the Bowl and Grow
Surface before putting them back
together and setting them back on
the Base.
10
If your Grow Bulbs have been in use
more than 6 months, they should be
replaced at this time.
Your AeroGarden is now ready for
11
replanting.
Use only water and mild soap when
cleaning your AeroGarden (except
when Sanitizing - Step 7). Do not use
!
abrasive cleaners or run through the
dishwasher.
* IMPORTANT NOTE: We recommend replacing the Pump Filter after growing two gardens.
Order Pump Filters from www.aerogardensupport.com or from your retailer.
12
Page 14
Prepare For Your Next Garden (continued)
Replanting Your AeroGarden
If this is the FIRST garden planted in your AeroGarden, you may DISREGARD these
instructions.
If you have already grown a garden in your AeroGarden, please follow the instructions below to
reset the nutrient timer:
Before planting a new garden, be sure to restart the nutrient timer.
• Press and hold “Reset” button until the red “Add Nutrient” light blinks 3 or 4 times
(approximately 9 seconds).
• Release “Reset” button. “Add Nutrient” light will turn off.
• Your nutrient timer is now reset.
(In some cases you may see other lights blink as well. This is nothing to worry about.)
Reset
Add Nutrient
Remember to...
• Replace your Grow Bulbs after 6 months of use.
www.aerogardensupport.com or from your retailer.
• Sanitize your AeroGarden before re-planting (see page 12).
• Set Lamp Hood to the lowest position when starting a new garden.
Grow Bulbs can be ordered at
13
Bundle cord when furnishing is not in use.
!
Page 15
Notes…
14
Page 16
U.S. CAUTION –
authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected; or, Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modications not expressly approved in this manual could void your
To reduce the risk of electric shock, this furnishing has a
polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER UN CHOC ÉLECTRIQUE,
PRÉSENTER LA LAME LARGE À LA FENTE LARGE ET
POUSSER JUSQU’AU FOND
.
© 2006-2008 AeroGrow International, Inc., Boulder, CO U.S.A. U.S. Patents Pending
5/7/08
Loading...