AEMC JM865A Operating Manual

AC Current Probe
Model JM865A
User Manual
DESCRIPTION
The JM865A (Catalog # 2110.88) is designed for use in industrial environments. The “squared” jaws permit multiple conductor or bus bar positioning. The current output makes it the perfect tool for measurement with DMMs, recorders, power and harmonic meters. Three ranges allow you to obtain the best resolution even on low current measurement. The Model JM865A is compatible with any AC Ammeter, multimeter, or other current measuring instrument with an input impedance lower than 2Ω. To achieve the stated accuracy, use the JM865A with an Ammeter having an accuracy of 0.75%.
WARNING
These safety warnings are provided to ensure the safety of personnel and proper operation of the instrument.
• Read the instruction manual completely and follow all the safety information before attempting to use or service this instrument.
• Use caution on any circuit: Potentially high voltages and currents may be present and may pose a shock hazard.
• Read the Safety Specifications section prior to using the current probe. Never exceed the maximum voltage ratings given.
• Safety is the responsibility of the operator.
• ALWAYS connect the current probe to the display device before clamping the probe onto the sample being tested.
• ALWAYS inspect the instrument, probe, probe cable, and output terminals prior to use. Replace any defective parts immediately.
• NEVER use the current probe on electrical conductors rated above 600V in overvoltage category III (CAT III). Use extreme caution when clamping around bare conductors or bus bars.
INTERNATIONAL ELECTRICAL SYMBOLS
This symbol signifies that the current probe is protected by double or reinforced insulation. Use only factory specified replacement parts when servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer to the user manual before using the instrument.
This is a type A current sensor. This symbol signifies that application around and removal from HAZARDOUS LIVE conductors is permitted.
DEFINITION OF MEASUREMENT CATEGORIES Cat. I: For measurements on circuits not directly connected to the AC supply wall outlet such as
protected secondaries, signal level, and limited energy circuits.
Cat. II: For measurements performed on circuits directly connected to the electrical distribution system.
Examples are measurements on household appliances or portable tools.
Cat. III: For measurements performed in the building installation at the distribution level such as on
hardwired equipment in fixed installation and circuit breakers.
Cat. IV: For measurements performed at the primary electrical supply (<1000V) such as on primary
overcurrent protection devices, ripple control units, or meters.
RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify your distributor of any missing items. If the equipment appears to be damaged, file a claim immediately with the carrier and notify your distributor at once, giving a detailed description of any damage.
Ø=2.52" (64 mm)
Cable max.
1.97 x 5.31" (50 x 135 mm) or
2.52 x 3.94" (64 x 100 mm) Bus Bar max.
12.40"
(315 mm)
P1 P2
4.72"
(120 mm)
ELECTRICAL SPECIFICATIONS
Current Range:
1 to 1000A AC continuous cycle 1 to 2000A AC continuous cycle 1 to 2400A AC continuous cycle for the full temperature range.
(3000 A if temperature <35º C or 95º F)
Transformation Ratio:
1000:5, 2000:5 -3000:5
Output Signal:
5mA AC/A AC (5A at 1000A)
2.5mA AC/A AC (5A at 2000A)
1.666mA AC/A AC (5A at 3000A)
1.89"
(48 mm)
Red Black
S2S1
Accuracy and Phase Shift*: 1000A RANGE
Primary current 50A 200A 1000A Accuracy % 3% 1.5% 1% Phase shift 1.5°
Load Impedance: 0.1 Overload: 1200A for 10 mn Ampere Second Product: 15 A.s Accuracy: Per IEC 185-26-27
Class 1 (2.5VA) from 48 to 1000 Hz
2000A RANGE
Primary current 100A 400A 2000A
Accuracy % 1.5% 0.75% 0.5% Phase shift 1.5° 0.75° 0.5°
Load Impedance: 0.2 Overload: 2400A for 10 mn Ampere Second Product: 50 A.s Accuracy: Per IEC 185-26-27
Class 0.5 (5 VA) from 48 to 1000 Hz
3000A RANGE
Primary current 150A 600A 3000A
Accuracy % 1.5% 0.75% 0.5% Phase shift 1.5° 0.75° 0.5°
Load Impedance: 0.4 Overload: 3600A for 10 mn Ampere Second Product: 80 A.s Accuracy: Per IEC 185-26-27
Class 0.5 (10VA) from 48 to 1000 Hz
(*Reference conditions: 23°C±3°K, 20 to 85% RH, 45 to 65 Hz, external magnetic field < 40 A/m, no DC component, no external current carrying conductor, test sample centered.)
Frequency Range: 30 to 1500 Hz; current derating above 1500Hz for continuous use
Working Voltage: 600V AC Common Mode Voltage: 600V AC Influence of Adjacent Conductor:
< 0.005A/A AC
Influence of Conductor in Jaw Opening:
1.5% ± 0.2A on 1000:5 range 1% ± 0.2A on 2000:5 range 1% ± 0.2A on 3000:5 range
MECHANICAL SPECIFICATIONS
Operating Temp: 14° to 122°F (-10° to 50°C) Storage Temp: -13° to 176°F (-25° to 80°C) Influence of Temperature: < 0.1% per 10°K Jaw Opening: 3.54" (90 mm)
Maximum Conductor Size:
Cable: 2.52" Ø max. (64mm) Bus bar: 1.97 x 5.31" (50 x 135 mm)
2.52 x 3.94" (64 x 100 mm)
Envelope Protection: IP 20 (IEC 529) Drop Test: 1 m (IEC 68-2-32) Mechanical Shock: 100 g (IEC 68-2-27) Vibration: 10/55/10 Hz, 0.15 mm (IEC 68-2-6) Polycarbonate Material:
Handles: 10% fiberglass charged polycarbonate UL 94 V0
Jaws: ABS UL 94 V2
Dimensions:
4.72 x 12.40 x 1.9" (120 x 315 x 48 mm)
Weight: 2.65 lbs. (1200 g) Colors: Dark gray handles with red jaws Output:
Two standard safety banana jacks (4mm)
SAFETY SPECIFICATIONS
Electrical:
Double insulation or reinforced insulation between primary or secondary and outer case of handle upon IEC 1010-2-32
Common Mode Voltage:
600V Category III, Pollution: 2
ORDERING INFORMATION
Current Probe JM865A...................Cat #2110.88
Includes a user manual and a product warranty and registration card
Accessories:
Leads, set of 2, 5 ft safety (1000V)...Cat #2111.29
Lead No. 211 for Probe 5A Series
(5 ft rated 250V)................................Cat #2950.06
OPERATION
Please make sure that you have already read and fully understand the WARNING section on page 1.
Making Measurements with the AC Current Probe Model JM865A
• Connect the black and red terminals to the Ampere AC range of your DMM or current measuring instrument. Select the appropriate current range.If the current magnitude is unknown, select the highest range (3000 A AC / 5 A AC) on the switch probe located inside the handle. Clamp the probe around the conductor to be tested, with the arrow pointeddd toward the load. Select the lower range until you obtain the best resolution. Read the value display on the DMM and multiply it by the range selected. (If reading = 2.59 A on the 1000/5 range, the current flowing through the probe is 2.59 A x 200 = 518 A AC).
• For best accuracy: carefully center the conductor inside the probe jaw, avoid if possible, the proximity of other conductors which may create noise.
Tips for Making Precise Measurements
• When using a current probe with a meter, it is important to select the range that provides the best resolution. Failure to do this may result in measurement errors.
• Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for power measurement.
MAINTENANCE:
Warning
• For maintenance use only original replacement parts.
• To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.
• To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents into the probe.
Cleaning
To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all times. Failure to do so may result in error in readings.To clean the probe jaws, use very fine sand paper (fine
600) to avoid scratching the jaw, then gently clean with a soft oiled cloth.
REPAIR AND CALIBRATION
You must contact our Service Center for a Customer Service Authorization number (CSA#). This will ensure that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA# on the outside of the shipping container. If the instrument is returned for calibration, we need to know if you want a standard calibration, or a calibration traceable to N.I.S.T. (includes calibration certificate plus recorded calibration data).
Chauvin Arnoux
®
, Inc. d.b.a. AEMC® Instruments
15 Faraday Drive Dover, NH 03820 USA
Tel: (800) 945-2362 (Ext. 360) (603) 749-6434 (Ext. 360) Fax: (603) 742-2346 or (603) 749-6309
repair@aemc.com (Or contact your authorized distributor) Costs for repair, standard calibration, and calibration traceable to N.I.S.T. are available.
NOTE: All customers must obtain a CSA# before returning any instrument. TECHNICAL AND SALES ASSISTANCE
If you are experiencing any technical problems, or require any assistance with the proper use or application of this instrument, please call our technical hotline:
(800) 343-1391 • (508) 698-2115 • Fax (508) 698-2118 Chauvin Arnoux
®
, Inc. d.b.a. AEMC® Instruments
techsupport@aemc.com
www.
aemc.com
99-MAN 100125.v4 06/07
Loading...