Thank you for choosing one of our high-quality products.
With this appliance you will experience the perfect combination of functional
design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best
performance and control - indeed we are setting the highest standards of
excellence.
In addition to this you find environmental and energy saving aspects as an integral
part of our products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
The following symbols are used in this user manual:
Important information concerning your personal safety and information on how
to avoid damaging the appliance.
General information and tips
Environmental information
Contents
3
Contents
Operating Instructions 5
Important safety information 5
Product description 8
Control panel 9
Before first use 9
Sorting and preparing laundry 10
Programme overview 11
Daily use 13
Switching machine on 13
Opening loading door / loading laundry 13
Selecting the programme 13
DELICATE (SCHON) function 13
BUZZER (SIGNAL) function 14
DELAY START (ZEITVORWAHL) function 14
Starting the programme 15
Changing programme 15
Putting in extra items or taking items out before end of programme 16
Drying cycle complete / removing laundry 16
Care and cleaning 17
Cleaning fluff filter 17
Cleaning the door seal 19
Emptying the condensate tank 19
Cleaning heat exchanger 20
Cleaning the drum 21
Clean operating screen and housing 22
What to do if ... 23
Troubleshooting by yourself 23
Machine settings 25
Technical data 27
Consumption values 28
136901660-00-05112007
Contents
4
Hints for test institutes 28
Installation 29
Appliance positioning 29
Removing transport safety packaging 30
Electrical connection 30
Changing door stop 30
Special accessories 32
Environment 34
Packaging material 34
Old appliance 34
Environmental tips 35
Service 36
Subject to change without notice
Important safety information
Operating Instructions
Important safety information
In the interest of your safety and to ensure the correct use, before installing
and first using the appliance, read this user manual carefully, including its
hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar
with its operation and safety features. Save these instructions and make
sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use
and safety.
General safety
• It is dangerous to alter the specifications or attempt to modify this product in
any way.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Make sure that small pets do not climb into the drum. To avoid this, please check
into the drum before using.
• Any objects such as coins, safety pins, nails, screws, stones or any other hard,
sharp material can cause extensive damage and must not be placed into the
machine.
• In order to avoid danger of fires caused by excessive drying, do not use appliance
to dry the following items: Cushions, quilts and the like (these items accumulate
heat).
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not
be dried in the tumble dryer.
• Always unplug the appliance after use, clean and maintenance.
• Under no circumstances should you attempt to repair the machine yourself.
Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare
parts.
5
Important safety information
6
• Items that have been soiled with substances such as cooking oil acetone, petrol,
kerosene, spot removers, turpentine, waxes and wax removers should be washed
in hot water with an extra amount of detergent before being dried in the tumble
dryer.
•
Danger of explosion: Never tumble dry items that have been in contact with
inflammable solvents (petrol, methylated spirits, dry cleaning fluid and the like).
As these substance are volatile, they could cause an explosion. Only tumble dry
items washed with water.
•
Risk of fire: items that have been spotted or soaked with vegetable or cooking
oil constitute a fire hazard and should not be placed in the tumble dryer.
• If you have washed your laundry with stain remover you must execute an extra
rinse cycle before loading your tumble dryer.
• Please make sure that no gas lighters or matches have accidentally been left in
pockets of garments to be loaded into appliance
WARNING!
Never stop a tumble dry before the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is dissipated.
Installation
• This appliance is heavy. Care should be taken when moving it.
• When unpacking the appliance, check that it is not damaged. If in doubt, do not
use it and contact the Service Centre.
• All packing and transit bolts must be removed before use. Serious damage can
occur to the product and to property if this is not adhered to. See relevant section
in the user manual.
• The final part of a tumble dryer cycle occurs without heat ( cool down cycle ) to
ensure that the items are left at a temperature that ensures that items will not
be damaged.
• Any electrical work required to install this appliance should be carried out by a
qualified electrician or competent person.
• Care must be taken to ensure that the appliance does not stand on the electrical
supply cable.
• If the machine is situated on a carpeted floor, please adjust the feet in order to
allow air to circulate freely.
• After having installed the appliance, check that it is not pressing or standing on
its electrical supply cable.
Important safety information
7
• If the tumble dryer is placed on top of a washing machine, it is compulsory to
use the stacking kit (optional accessory).
Use
• This appliance is designed for domestic use. It must not be used for purposes
other than those for which it was designed.
• Only wash fabrics which are designed to be machine dried. Follow the instructions on each garment label.
• Do not dry unwashed items in the tumble dryer.
• Do not overload the appliance. See the relevant section in the user manual.
• Clothes which are dripping wet should not be placed in the dryer.
• Garments which have been in contact with volatile petroleum products should
not be machine dried. If volatile cleaning fluids are used, care should be taken
to ensure that the fluid is removed from the garment before placing in the
machine.
• Never pull the power supply cable to remove the plug from the socket; always
take hold of the plug itself.
• Never use the tumble dryer if the power supply cable, the control panel, the
working surface or the base are damaged so that the inside of the tumble dryer
is accessible.
• Fabric softeners, or similar products should be used as specified by the fabric
softener instructions.
•
Caution - hot surface : Do not touch the door light cover surface when the
light is switched on.
1)
Child safety
• This machine is not intended for use by young children or infirm persons without
supervision.
• Children should be supervised to ensure that they do not play with the appliance.
• The packaging components (e.g. plastic film, polystyrene) can be dangerous to
children - danger of suffocation! Keep them out of children’s reach.
• Keep all detergents in a safe place out of children’s reach.
• Make sure that children or pets do not climb into the drum.
1) Only dryers equipped with internal drum light.
Product description
8
Product description
2
5
6
8
11
1 Control panel
2 Drawer with condensed water container
3 Fine strainer (lint filter)
4 Large mesh filter (lint filter)
5 Micro-fine filter (lint filter)
6 Rating plate
7 Loading door (reversible)
8 Base door upstream of heat exchanger
9 Button for opening door in plinth
10 Air slots
11 Screwed feet (with height adjustment)
1
3
4
7
9
10
Control panel
Control panel
9
5
123
1
Programme knob and OFF AUS switch
2 Function buttons
3 START PAUSE button
4
DELAY START ZEITVORWAHL button
5 Function and warning leds
Before first use
In order to remove any residues which may have been produced during production,
wipe the dryer drum with a damp cloth or carry out a brief drying cycle (30 MIN)
with damp cloths in the machine.
4
Sorting and preparing laundry
10
Sorting and preparing laundry
Sorting laundry
• Sort by fabric type:
–
Cotton/linen for programmes in COTTONS BAUMWOLLE programme group.
–
Mixtures and synthetics for programmes in SYNTHETICS MISCHGEWEBE programme group.
• Sorting by care label. The care labels mean:
Drying in the tumble
dryer possible in prin-
ciple
Dry at normal
temperature
Dry at reduced
temperature (press
DELICATE SCHON but-
ton!)
Drying in the tumble
dryer not possible
Do not place in the appliance any wet laundry which is not specified on the care
label as being suitable for tumble-drying.
This appliance can be used for all wet laundry items which are labelled as suitable
for tumble-drying.
• Do not dry new, coloured textiles together with light-coloured laundry items.
Textile colours may bleed.
•
Do not dry cotton jersey and knitwear with the EXTRA EXTRATROCKEN programme. Items may shrink!
•
Do not dry wool in the dryer. May become entangled!
Preparing laundry
• To avoid laundry becoming tangled: close zips, button up duvet covers and tie
loose ties or ribbons (e.g. of aprons).
• Turn items with double-layered fabrics inside out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost). These fabrics will then dry better.
Programme overview
Additional
functions
Programmes
EXTRA
EXTRATROC
KEN
CUPBOARD
SCHRANKT
ROCKEN
COTTONS BAUMWOLLE
IRON
BÜGELTRO
CKEN
max. load
(weight when dry)
DELICATE SCHON
6 kg•••
6 kg•••
6 kg•••
DELAY START
BUZZER SIGNAL
Programme overview
pplication/properties
ZEITVORWAHL
Thorough drying of thick or multi- layered fabrics,
e.g. terry towelling items, bathrobes.
Thorough drying of fabrics of even thicknesses, e.g.
terry towelling items, knitwear, towels.
For normal thickness cotton or linen laundry, e.g.
bedding, table linen.
11
Care mark
EXTRA
EXTRATROC
KEN
CUPBOARD
SCHRANKT
ROCKEN
SYNTHETICS MISCHGEWEBE
IRON
BÜGELTRO
CKEN
Time
30 MIN.1 kg•••
FRESHEN
UP AUFFRI-
SCHEN
3 kg•••
3 kg•••
3 kg•••
1 kg•••
Thorough drying of thick or multi-layered fabrics,
e.g. pullovers, bedding, table linen.
For thin fabrics which are not ironed, e.g. easy care
shirts, table linen, baby clothes, socks, lingerie with
bones or wires.
For thin fabrics which are also to be ironed, e.g.
knitwear, shirts.
For further drying of individual items of laundry
or for small volumes of less than 1kg.
For refreshing or gently cleaning textiles with
commercially available dry cleaning products.
1)
1)
1)
Programme overview
12
Programmes
Additional
functions
max. load
(weight when dry)
DELICATE SCHON
DELAY START
BUZZER SIGNAL
pplication/properties
Care mark
ZEITVORWAHL
BED LINEN
BETTWÄ-
Special
SCHE
JEANS6 kg•••
1) select DELICATE SCHON
3 kg•••
Bed linen (single and double sheet, pillowcase,
bedspread, duvet cover).
For leisure clothing, such as jeans, sweat-shirts,
etc., of different material thicknesses (e.g. at the
neck, cuffs and seams).
Daily use
Daily use
Switching machine on
Turn the programme selector to any programme. The machine has been switched
on. Led of START PAUSE button is flashing.
Opening loading door / loading laundry
1. Open loading door:
Use force to push against the loading
door (push point)
2. Load your laundry (do not force it in).
CAUTION!
Do not jam laundry in between the loading door and rubber seal.
3. Close loading door securely. Lock
must audibly lock.
13
Selecting the programme
Use the programme selector to set the programme you require.
DELICATE (SCHON) function
For especially gentle drying of sensitive fabrics with the care label and for
temperature-sensitive textiles (e.g. acrylic, viscose). Programme is executed with
reduced heat.
DELICATE SCHON function is only suitable for use with loads of up to 3kg.
Daily use
14
To activate it:
1. Choose the drying programme.
2.
Press DELICATE SCHON button - the led
above is on.
To deselect function press again DELICATE
SCHON button. Led above is off.
BUZZER (SIGNAL) function
The appliance is supplied with the BUZZER SIGNAL function deactivated.
The buzzer sounds or plays a tune when activated during:
–cycle end
– anti-crease phase and when phase starts or ends
– cycle interruption by a warning
–alarm
To activate it:
1. Choose the drying programme.
2.
Press BUZZER SIGNAL button - the led
above is on.
To deselect function press again BUZZER SIG-NAL button. Led above is off.
DELAY START (ZEITVORWAHL) function
With the DELAY START
programme by 3, 6 or 9 hours.
1. Select the programme and additional functions if necessary.
Zeitvorwahl
button, you can delay the start of a
Daily use
2.
Press the DELAY START Zeitvorwahl
button as many times as necessary
until the required delay time is
chosen. Corresponding led is lighting.
–
9h display for programme to start
in 9 hours.
–
6h display for programme to start
in 6 hours.
–
3h display for programme to start
in 3 hours.
By pressing the DELAY START ZEITVORWAHL button again, the time delay is cancelled. The led is off.
3. To activate the delay timer, press the START PAUSE button.
If a time delay of 9 hours is selected, the led 9h is lighting. After 3 hours, the 9h
led is off and 6h led is lighting; after another 3 hours, 3h led is lighting. After a
total of 9 hours, the programme will start.
Starting the programme
15
Press the START PAUSE button. Led above
stops flashing, becomes steady. The programme is started. Lighting status LED shows
you cycle run.
Changing programme
To change a programme which has been selected by mistake once the programme
has started, first turn the programme selector to OFF AUS position. The programme
is cancelled.
The programme can no longer be changed directly once the programme has started.
If nevertheless there is an attempt to change the programme on the programme
knob or if an function button (excluding the BUZZER SIGNAL button) is pressed,
led above START PAUSE button starts flashing temporarily in yellow. The drying
programme is not however affected by this (laundry protection).
Daily use
16
Putting in extra items or taking items out before end of programme
1. Open loading door.
WARNING!
Laundry and drum can become hot. Risk of burns!
2. Load or remove laundry items.
3. Close loading securely. Lock must audibly lock.
4. Press the START PAUSE button to continue the drying cycle.
Drying cycle complete / removing laundry
Once the drying cycle is complete, END status led is lighting. If the BUZZER SIGNAL button has been pressed, an acoustic signal sounds intermittently for about
one minute.
The drying cycles are automatically followed by an anti-crease phase which lasts
around 30 minutes. The drum rotates at intervals during this phase. This keeps the
laundry loose and free of creases. The laundry can be removed at any time during
the anti-crease phase. (The laundry should be taken out towards the end of the
anti-crease phase at the latest to prevent creases from forming.)
1. Open door.
2. Before removing the laundry, remove fluff from the micro-fine filter. It is best
to use a damp hand for this purpose. (See “Care and cleaning” chapter.)
3. Remove laundry.
4.
Turn the programme selector to OFF AUS.
After each drying cycle:
- Clean the micro-fine filter and fine filter
- Drain the condensed water container
(See chapter “Care and cleaning”.)
5. Close the door.
Care and cleaning
Care and cleaning
Cleaning fluff filter
The filters collect all the fluff which accumulates during drying. To ensure that the
dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be
cleaned after every drying cycle.
The warning led FILTER (SIEB) is on to remind you this operation.
CAUTION!
Never operate the dryer without fluff filters or with damaged or blocked fluff filters.
1.Open loading door
2.Use a damp hand to clean the mi-
cro- fine filter, which is built into
the lower part of the loading aperture.
17
3.After a period of time, a patina due
to detergent residue on laundry
forms on the filters. When this occurs, clean the filters with warm
water using a brush. Remove the
filter from the door pulling it out. It
can be positioned with the tooth
facing to the left or to the right).
After cleaning do not forget to put
it back.
Care and cleaning
18
4.Push down unlock button on large
mesh filter.
Large mesh filter jumps up.
5.Take out fine strainer.
6.Remove fluff from fine strainer. It
is best to use a damp hand for this
purpose.
Clean the entire filter area
The strainer area does not have to
be cleaned after every drying cycle,
but should be checked regularly
and cleaned of fluff if necessary.
7.To do this, grip the top of the large mesh filter and pull it forwards until it
comes loose from the two brackets.
8.Remove fluff from the entire filter
area. It is best to use a vacuum
cleaner for this purpose.
9.Press both journals of the large
mesh filter into the brackets on the
loading door until they snap into
place.
10. Re-insert fine strainer.
11. Press against the large mesh filter
until it locks into the interlock.
Care and cleaning
If the fine strainer is not fitted, the large mesh
filter will not snap into place and the loading
door cannot be closed.
Cleaning the door seal
Wipe the door seal with a damp cloth immediately after the drying cycle has
finished.
Emptying the condensate tank
Empty condensate tank after every drying cycle.
If the condensate tank is full, an active programme will break off automatically
and the warning led TANK (BEHÄLTER) light up. In order to continue the programme, the condensate tank must first be emptied.
19
WARNING!
The condensate is not suitable for drinking or for preparing foodstuffs.
1. Take out drawer containing con-
densed water container completely
1 and pull up the condensed water
container’s drainage pipe as far as it
will go 2.
2
1
Care and cleaning
20
2. Pour condensed water out into a ba-
sin or similar receptacle.
3. Slide outlet connections in and refit
condensate tank.
If the programme has been interrup-
ted as a result of the condensate tank
being full: Press the START PAUSE
button to continue the drying cycle.
The condensate tank has a volume of approx. 3.6 litres. This is sufficient for around
6 kg of laundry which has previously been spun at 1000 revolutions/ minute.
The condensate can be used as distilled water, e.g. for steam ironing. However first
filter the condensate (e.g. with a coffee filter) to remove any residue and small
pieces of fluff.
Cleaning heat exchanger
If the warning led CONDENSER (WÄRMETAUSCHER) is lighting, the heat exchanger
needs to be cleaned.
CAUTION!
Operating when the heat exchanger is blocked with fluff can damage the dryer.
This also increases energy consumption.
1. Open door.
2. Open door in plinth. To do this, press
the release button on the bottom of
the door aperture and open the door
in the plinth to the left.
3. Clean fluff from the inside of the
door and the heat exchanger front
chamber. Wipe the door seal with a
damp cloth.
Care and cleaning
4. Turn both lock washers inwards.
5. Use the handle to pull the heat
exchanger out of the base and carry
it horizontally to prevent any re-
maining water from spilling.
6. To empty the heat exchanger, hold
vertically over a washing-up bowl.
CAUTION!
Do not use sharp objects to clean. The
heat exchanger could develop leaks.
7. Clean heat exchanger.
It is best to use a brush or to rinse thoroughly with a hand-held shower.
8. Replace heat exchanger and lock into place (turn both lock washers outwards
until they snap into place).
9. Close door in plinth.
21
CAUTION!
Never operate the dryer without the heat exchanger.
Cleaning the drum
CAUTION!
Do not use abrasives or steel wool to clean the drum.
Lime in the water or cleaning agents may form a barely visible lining on the inside
of the drum. The degree to which the laundry has been dried is then no longer
detected reliably. The laundry is damper than expected when removed from the
dryer.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the
inside of the drum and drum ribs.
Care and cleaning
22
Clean operating screen and housing
CAUTION!
Do not use furniture cleaners or aggressive cleaning agents to clean the machine.
Use a damp cloth to wipe down the operating screen and housing.
What to do if ...
What to do if ...
Troubleshooting by yourself
If, during operation, the dryer shows an error (one or more leds flashing on the
control panel), check first of all whether you can remedy the problem yourself by
means of the table below. If you cannot solve the problem: Switch the machine off
and on again. Reset programme. Press the START PAUSE button. If the error is still
shown, please contact our after-sales service and inform them which leds are
flashing.
ProblemPossible causeRemedy
Dryer does not work.
Drying results
unsatisfactory.
Loading door does not
close.
Mains plug is not plugged in or fuse
is not working correctly.
Loading door is open.Close loading door.
Have you pressed the START PAUSE
button?
Wrong programme selected.
Lint filters clogged.Clean lint filters.
Fluff filter clogged.Clean fluff filter.
Heat exchanger clogged with lint.Clean heat exchanger.
Overloading of laundry.
Ventilation slots in base area covered up.
Residue on inside surface of drum
or drum ribs.
Conductance of water at installation site differs from standard setting of machine.
Fine strainer not in place and/or
mesh filter not locked in place.
Plug in at mains socket. Check fuse
in fuse box (domestic installation).
Press the START PAUSE button
again.
Select a different programme the
next time you dry (see “Programme
chart” chapter).
Observe recommended loading volumes.
Uncover ventilation slots in base
area.
Clean inside surface of drum and
drum ribs.
Re-programme standard setting
for degree of drying (see ‘Machine
settings’ chapter).
Install fine strainer and/or snap
large mesh filter into place.
23
What to do if ...
24
When a button is
pressed, led above
START PAUSE button is
lighting in yellow
temporarily.
Programme inactive,
empty water tank
warning led is lighting.
Drying cycle ends
shortly after programme starts.
Drying cycle lasts an
unusually long time.
Note: After around 5
hours the drying cycle
ends automatically
(see „Drying cycle
complete ”).
Washing protection. After the start
of the programme, the option can
no longer be set.
Condensate tank is full.
Not enough washing loaded or
washing loaded is too dry for selected programme.
Lint filter clogged.Clean lint filter.
Fluff filter clogged.Clean fluff filter.
DELICATE SCHON button pressed
and/or load volume too big.
Laundry insufficiently spun.Laundry must be adequately spun.
Particularly high room temperature. Temporary switching off of
the compressor to avoid overload.
Turn the programme knob to OFF
AUS. Set the programme again.
Empty condensate tank, then start
programme with START PAUSE button.
Select time programme or higher
drying level (e.g. EXTRA DRY
EXTRATROCKENn instead of CUPBOARD DRY SCHRANKTROCKEN).
Reduce load volume.
Automatic process, there is no fault
with the appliance. If possible,
lower the room temperature.
Machine settings
SettingImplementation
BUZZER
off
Water hardness
Water contains, a variable quantity
of limestone and mineral salts of
which quantities vary according to
geographical locations thus varying its conductivity values.
Relevant variations of the
conductivity of the water compared
to those prefixed by the factory
could slightly influence the residual
humidity of the laundry at the end
of the cycle. Your dryer allows you
to regulate the sensitivity of the
drying sensor based on
conductivity values of the water.
SIGNAL
permanent on/
Machine settings
1. Turn the programme selector to any programme.
2.
Press simultaneously the DELICATE SCHON and BUZZER
SIGNAL buttons and hold down for approx. 5 seconds the
result can be following:
–
diode above BUZZER SIGNAL button starts lighting BUZZER permanently on.
– lighting diode comes off - BUZZER permanently off.
3. The BUZZER is by default always off. You can use BUZZER
SIGNAL button to activate or deactivate sound but machine does not memorize your selection.
1. Turn the programme selector to any programme.
2.
Press simultaneously the DELICATE SCHON and START
PAUSE buttons and hold down for approx. 5 seconds. The
current setting is shown by lighting status diode:
–
EMPTYING WATER TANK BEHÄLTER diode - low
conductivity <300 micro S/cm
–
FILTER SIEB diode - medium conductivity 300-600 mi-
cro S/cm
–
CONDENSER WÄRMETAUSCHER diode - high
conductivity >600 micro S/cm
3. Press the START PAUSE button sequentially until you set
desired level.
4. To memorize setting press simultaneously the DELICATE
SCHON and START PAUSE buttons or turn knob to OFF
AUS position
25
Machine settings
26
Emptying water tank - warning
message permanent off
When using an external drain for
the condensed water.
1. Turn the programme selector to any programme.
2.
Press simultaneously the BUZZER SIGNAL and DELAY
START ZEITVORWAHL buttons and hold down for approx.
5 seconds.
The current setting is shown by lighting EMPTYING WATER TANK BEHÄLTER diode:
–
EMPTYING WATER TANK BEHÄLTER diode flashes warning is permanently off
–
EMPTYING WATER TANK BEHÄLTER diode flashes and
becomes steady - led warning is activated
By default the warning led is activated and is lighting always
at the end of the drying cycle or during the cycle if the water
container is full.
Technical data
Technical data
This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive
92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth85 x 60 x 58 cm
Depth with loading door open109 cm
Height can be adjusted by1.5 cm
Weight when emptyapprox. 40 kg
1)
Loading volume (depends on programme)
Energy consumption in accordance with IEC
61121 s. e. (6 kg of cotton, pre-drained at 1000
Parameters possible to checked by the Test Institutes:
• Energy consumption (corrected with final humidity) during the cupboard dry
cotton cycle with nominal load.
• Energy consumption (corrected with final humidity) during the cupboard dry
cotton cycle with half load.
• Final humidity (during Cupboard dry cotton, Iron dry cotton and Cupboard dry
Easy care)
• Condensation efficiency (corrected with final humidity) during cupboard dry
cotton cycle with nominal and half load
All the cycles have to be checked in accordance with IEC 61121 (Tumble dryers for
household use – Methods for measuring the performance).
kWh
Installation
Installation
Appliance positioning
• It is recommended that, for your convenience, the machine is positioned close
to your washing machine.
• The tumble dryer must be installed in a clean place, where dirt does not build
up.
• Air must be able to circulate freely all round the appliance. Do not obstruct the
front ventilation grille or the air intake grilles at the back of the machine.
• To keep vibration and noise to a minimum when the dryer is in use, it should be
placed on a firm, level surface.
• Once in its permanent operating position, check that the dryer is absolutely level
with the aid of a spirit level. If it is not, raise or lower the feet until it is.
• The feet must never be removed. Do not restrict the floor clearance through
deeppile carpets, strips of wood or similar. This might cause heat built-up which
would interfere with the operation of the appliance.
The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The
appliance must therefore not be installed on floors which are not resistant to high
temperatures.
When operating the tumble dryer, the room temperature must not be lower than
+5°C and higher than +35°C, as it may affect the performance of the appliance.
29
WARNING!
Should the appliance be moved, it must be transported vertically.
WARNING!
The appliance must not be installed behind the lockable door, a sliding door a door
with a hinge on the opposite side to that of the appliance.
Installation
30
Removing transport safety packaging
CAUTION!
Before use all parts of the transport packaging must be removed.
1. Open loading door
2. Pull off adhesive strips from inside ma-
chine on top of drum.
3. Remove foil hose and polystyrene
padding from the machine.
Electrical connection
Details on mains voltage, type of current and the fuses required should be taken
from the type plate. The type plate is fitted near the loading aperture (see “Product
description” chapter).
WARNING!
The manufacturer declines any responsibility for damage or injury through
failure to comply with the above safety precautions. Should the appliance
power supply cable need to be replaced, this must be carried out by our
Service Center.
The power supply cable must be accessible after installing the machine.
Connect the machine to an earthed socket, in accordance with current wiring
regulations.
Changing door stop
WARNING!
Installation
The door stop may only be changed by a specialist. If necessary, please contact our
after-sales service or your specialist dealer.
WARNING!
Before changing the door stop, disconnect the mains plug.
1.Open loading door.
2.
Unscrew hinge A from the front of the
machine and take off the loading door.
3.
Remove cover plates B and C. To do this,
insert a thin screwdriver into the slots as
shown in the illustration, press downwards slightly and pry out the cover
plates.
4.Use an appropriate tool and exert pres-
sure to unfasten locking block D from
the snap-on fixture, take out and re-insert on the other side having rotated the
block through 180°.
5.
Unscrew hinge A from the loading door,
rotate through 180°, re-insert on the
opposite side and screw down.
6.
Re-insert cover plates B and C on the opposite site having first rotated them
through 180°.
AC
B
A
31
D
C
Installation
32
7.
Unscrew cover plates E from the
front of the machine, rotate
through 180°, screw on the opposite side.
8.
Unscrew door lock F, push down
slightly and remove from the front
of the machine.
9.Disconnect cable connector from
door lock F.
10.
Press snap-in button G in and
down, press cover down slightly
and remove from front of the machine.
11. Disconnect cable connector from
cover G.
12.
Change door lock F over to the opposite side, insert the cable connector and
screw down the door interlock.
13. On the other side, insert the cable connector in cover G, insert cover and allow
snap-in button to lock into place.
14. Insert loading door and hinges into recesses on the front of the machine and
screw down.
Note regarding contact protection:The machine is only secure for operations
again once all plastic parts have been inserted.
E
F
E
F
G
G
Special accessories
Intermediate installation kit for stacked washer and dryer:
Available from your Service Force Centre or your specialist dealer
These intermediate installation kits can be used to arrange the dryer and an
automatic AEG-Electrolux washing machine (60cm wide, front loading) as a spacesaving washer/dryer stack. The automatic washing machine is at the bottom and
the dryer is at the top.
Version to be supplied:
– with extractable stacker plate 916.018 903
Read carefully the instructions supplied with the kit.
Installation
Installation kit for external condensate drain
Attached to your product
Installation kit 125 122 510 for direct draining of condensate into a basin, siphon,
gully, etc. The condensate tank then no longer has to be drained, it must however
remain in its intended position in the machine. Refer to the “Machine settings”
chapter for how to deactivate the EMPTY WATER TANK BEHÄLTER alert led.
Max. displacement height: 1m from the base of the dryer; max. displacement
length: 3m
Read carefully the instructions supplied with the kit.
33
Environment
34
Environment
Packaging material
The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose
of the packaging materials in the appropriate container at the community waste
disposal facilities.
Old appliance
The symbol on the product or on its packaging indicates that this product may
not be treated as household waste. Instead it should be taken to the appropriate
collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your
household waste disposal service or the shop where you purchased the product.
WARNING!
Remove mains plug from socket when you have no further use for the machine.
Cut off mains cable and dispose of together with plug. Destroy loading door hook.
Children cannot then lock themselves in the machine and put their lives at risk.
Environment
Environmental tips
• In the dryer, laundry becomes fluffy and soft. Fabric softeners are not therefore
needed when washing.
• Your dryer will function most economically if you:
– always keep the ventilation slots on the base of the dryer unobstructed;
– use the loading volumes specified in the programme overview;
– ensure you have good ventilation in the installation room;
– clean the micro-fine filter and fine strainer after each drying cycle;
– spin the laundry well before drying. Example: Consumption data – depending
on spinning speed – for 6 kg of laundry, dried using the COTTONS CUPBOARD
DRY BAUMWOLLE SCHRANKTROCKEN programme.
Pre-drainingDrying cycle
Revolutions per mi-
nute
10003.6603.8
12003.2533.4
14003.0503.3
18002.5422.5
Residual dampness
in litresas a %
Energy in kWh
35
363738
Service
In the event of technical faults, please first check whether you can remedy the
problem yourself with the help of the operating instructions (Chapter “What to do
if…”).
If you were not able to remedy the problem yourself, please contact the Customer
Care Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No.) (for numbers, see rat-
ing plate)
– Type of fault
– Any error messages displayed by the appliance
So that you have the necessary reference numbers from your appliance at hand,
we recommend that you write them in here:
Model description: ................................................................................