Before placing your new refrigerator/freezer into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the appliance.
Please keep these operating instructions for future reference. Pass them
on to possible new owners of the appliance.
Notes which are important for your safety or for the proper function-
1
ing of the appliance are stressed with a warning triangle and/or with
signal words (Warning!, Caution!, Important!). Please observe the following carefully.
01. This symbol and numbered instructions guide you step by step in the
operation of the appliance.
2. .....
Supplementary information regarding operation and practical uses of
3
the appliance appear after this symbol.
Tips and notes concerning economical and environmentally sound use
2
of the appliance are marked with the cloverleaf.
Explanations of the technical terminology used in the operating
instructions can be found at the end in the section "Technical
Terminology".
The operating instructions contain instructions for the correction of
possible malfunctions by the user in the section "What to do if ...". If
these instructions should not be sufficient, please contact your local
AEG-Electroux Service Force Centre.
nted on paper manufactured with environmentally sound processes.
These warnings are provided in the interests of your safety. Ensure
that you understand them all before installing or using this
appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings of these warnings contact the Customer
Care Department.
Prior to Installation
• Check the refrigerator/freezer for transport damage. Under no
circumstances should a damaged appliance be installed! In the event
of damage, please contact your retailer.
Installation
• This appliance is heavy. Care should be taken when moving it.
• It is dangerous to alter the specifications or attempt to modify this
product in any way.
• Ensure that the appliance does not stand on the electrical supply
cable. If the supply cable is damaged, it must be replaced by a cable
available from your local Service Force Centre.
• Make sure that the power plug is not squashed or damaged by the
back of the fridge/freezer. A damaged power plug may overheat and
cause a fire.
• If the power plug socket is loose, do not insert the power plug. There
is a risk of electric shock or fire.
• Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
• Parts which heat up should not be exposed. Whenever possible, the
back of the appliance should be close to a wall, but leaving the
required distance for ventilation, as stated in the installation
instructions.
• The appliance should be left for 2 hours after installation before it is
turned on, in order to allow the refrigerant to settle.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant
circuit of the appliance, a natural gas with a high level of
environmental compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain
that none of the components of the refrigerant circuit become
damaged.
818 38 80-00/75
Important Safety Instructions
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
Child Safety
• Do not allow children to tamper with the controls or play with the
product. Inform children of the possible dangers and instruct them in
the correct use of the appliance.
• Keep packaging material away from children! (There is a risk of
suffocation!)
During Use
• This appliance is designed for domestic use only, specifically for the
storage of edible foodstuffs only. It is not intended for commercial or
industrial use
• Containers with flammable gases or liquids can leak at low
temperatures. Do not store any containers with flammable materials
such as, spray cans, fire extinguisher refill cartridges etc in the
freezer.
• Frozen food should not be refrozen once it has thawed out.
• Do not place carbonated or fizzy drinks in the freezer.
• Ice lollies can cause ’frost/freezer burns’ if consumed straight from
the freezer compartment. Inform children of this danger.
• Do not remove items from the freezer compartment if your hands are
damp/wet, as this could cause skin abrasions or frost/freezer burns.
• Bottles and cans must not be placed in the freezer. They can burst
when the contents freeze.
• Manufacturers´ recommended storage times should be adhered to.
Refer to relevant instructions.
Maintenance and Cleaning
• Before cleaning, always switch off the appliance and disconnect from
the electrical supply.
• When unplugging always pull the plug from the mains socket, do not
pull on the cable. Damage to the cord may cause a short circuit, fire
and/or electric shock.
Servicing
• This product should be serviced by an authorised engineer and only
genuine spare parts should be used.
• Under no circumstances should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning.
6818 38 80-00/7
Contact your local AEG Service Force Centre.
Environmental Information
Packaging material
2
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at your local waste disposal facilities.
2Old appliance
The symbol
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you
purchased the product.
When disposing of your old appliance:
Make the appliance unusable by cutting off the cable and remove any
door catches to ensure small children cannot be trapped inside.
Help to keep your country tidy - use an authorised disposal site.
W on the product or on its packaging indicates that this
Appliance Transport
Two persons are required to transport the appliance. Two handles are
provided on the back of the appliance at the top to enable a better
hold. Before transporting, the plinth cover must be removed to prevent
damage.
01. To remove the plinth cover from
the stops, tilt downwards and then
pull forwards.
Important: Do not damage door
contact (if present)
818 38 80-00/77
2.
Grip the appliance with the recessed
handles positioned as in the drawing, and transport the appliance.
3. In order to push the appliance
into its final position, press carefully at the top of the door and
tip the appliance back slightly. The
weight is thus transferred to the
back wheels and the appliance can be easily pushed.
4. When the appliance is standing in
the desired place, attach the
plinth cover. First hook at the
hitches on the lower edge, then
press the grid in position. Make
sure that the door contact (if
present) is not damaged and that
it engages in the corresponding
aperture in the plinth cover.
1
2
Before Use
Packaging
01. Remove all adhesive tape and packaging from the interior of the appli-
ance.
Any remnants of adhesive can be removed with white spirit.
3
2. Remove the transport protection pieces and pull off the adhesive tape.
8818 38 80-00/7
3. Wash the inside of the appliance with lukewarm water with a little
bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap
or detergent as the smell may linger. Dry the appliance thoroughly.
Remove the transport fittings from
the storage shelves:
4. Slide the fittings securing the shelf
forward to the thicker section on the
edge of the storage shelf.
5. Take hold of the storage shelf at the
back and together with the fittings
slide the storage shelf far enough forward so that it can be hinged downwards and the fittings can be removed
from the guides.
Fitting the Door Handles
To keep the amount of packaging down and to reduce the size for
transporting, the door handles are not mounted when the appliance is
delivered.
Take care! Do not tighten screws too tightly (max. 2 Nm), the door
1
handles could be damaged.
The handles are packed separately on the padding in front of the door,
the brackets and screws inside the appliance.
To mount, lay the appliance carefully on its back, if necessary. Use a
piece of padding or a blanket as protection under the appliance.
01. Screw the top door bracket to the
door handle (1). Mount the
bottom door bracket to the
bottom of the door (2).
Important: Ensure door handle is
correctly positioned
2. Mount top door bracket on the
top of the door (3) and screw
handle to bottom door bracket
(4).
818 38 80-00/79
Installation
Installation Location
The appliance should be installed in a well ventilated, dry room.
Energy use and efficient performance of the appliance is affected by
the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature
corresponds to the climate classification, for which the appliance is
designed.
The climate classification can be found on the rating plate, which is
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for
each climate classification:
Climate classificationfor an ambient temperature of
SN+10 to +32 °C
N+16 to +32 °C
ST+18 to +38 °C
T+18 to +43 °C
If installation next to a source of heat is unavoidable, the following
minimum clearances must be maintained at the sides of the appliance:
– for electric cookers 3 cm;
– for oil and coal fired ranges 30 cm.
If these clearances cannot be maintained a heat insulating pad is required between the cooker and the refrigeration appliance.
10818 38 80-00/7
The refrigerator/freezer needs ventilation
Air is fed under the door through the
vent slots in the base and is exhausted
upwards along the back wall. To ensure
proper air circulation never cover or
alter the vent openings.
Important! If the appliance is installed
under a hanging cabinet, a clearance of
at least 10 cm between the top of the
appliance and the cabinet above it must
be maintained.
Please check whether, after installing
your appliance and especially after
reversing the door, the door seal seals
tightly. A badly fitting door seal may
lead to heavy frosting and a higher
power consumption (see also "What to
do if ...“).
01. Remove the two wall spacers from
the appliance accessories pack and,
in accordance with the illustrations,
fix them at the top of the rear of the
appliance so that the distance from
the wall required for the necessary
ventilation is ensured.
Installation
Appliance Alignment
The appliance must stand on a firm horizontal surface.
01. Please level out unevennesses in the
floor by screwing the two adjustable
front feet in or out using the 13 mm
spanner supplied. To do this remove
the plinth panel (see chapter
“Transporting the appliance“)
818 38 80-00/711
Installation
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING – THIS APPLIANCE MUST BE EARTHED
1
The manufacturer declines any liability should these safety measures
not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate is
inside, on the left.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Important
The wires in the mains lead are coloured in accordance with the
following code:
Green
Green and Yellow Earth
BlueNeutral
BrownLive
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings indentifying the
Blue
terminals in your plug, proceed
as follows:
1. The wire coloured green and
yellow must be connected to
the terminal marked with the
letter "E“ or by the earth
symbol or coloured green and yellow.
2. The wire coloured blue must be connected to the terminal "N“ or
coloured black.
3. The wire coloured brown must be connected to the terminal marked
"L“ or coloured red.
4. Upon completion there must be no cut, or stray strands of wire
present and the cord clamp must be secure over the outer sheat.
& Yellow
Brown
Cord Clamp
Warning! A cut-off plug inserted into a 13 amp socket is a serious
1
safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.
12818 38 80-00/7
Carbon filter
There is a active carbon filter in the rear wall of the fridge section. The
carbon filter cleans the air in the fridge section and in the LONGFRESH
0°C cold section by binding unpleasant smells.
Tip: The active carbon filter is a part subject to wear and is not covered
by the warranty.
Inserting and changing the active carbon filter:
When the fridge is delivered, the carbon filter is packed in a plastic bag
to ensure a long life. Before using the appliance for the first time, the
carbon filter must be inserted behind the air discharge grill.
With the fridge operating normally, the
carbon filter should be changed once a year to
ensure optimum function.
New carbon filters can be obtained from
specialist dealers or from the customer care
department.
01. To open the grill, press the lever on the right
of the grill (1) and open the grill forwards (2).
2. To change the old carbon filter, pull it from
the runners (3).
3. Insert the new carbon filter into the runners
of the grill (3) and press the grill closed until
it snaps into place.
Take care when handling the filter to prevent
1
dislodging carbon particles.
Reversing The Door
The door hinges can be changed if required to suit the location where
the appliance is installed.
Important! Only a qualified technician should change the side on
which the door is fixed. If this is necessary, please contact our Customer
Services or your dealer.
Warning! Unplug from the mains, before reversing the door.
1
818 38 80-00/713
Appliance Description
View of Appliance
(various models)
á Control panel
à Butter and cheese compartment with lid
â Door storage compartments
ä Bottle compartment
ã LONGFRESH 0 °C cold zone
å Shelves
ç Quick chill shelf
é Bottle and can holder
è Rating plate
ê Air discharge grill with regulator
ë Freezer drawer (only for storage). When defrosting the bottom
drawer also serves as a water collecting vessel
í Freezer drawer (for storage and freezing)
ì Freezer tray
14818 38 80-00/7
Appliance Description
Freezer tray
In the freezer section there is a
freezer tray in the second drawer
from the top. It can be used in both
the top drawer and the second
drawer from the top.
Berries and vegetables, for example,
can be pre-frozen on the freezer tray.
Advantage: The berries are not squeezed and maintain their natural
form. The frozen berries can then be stored in compartments or drawers
packaged in individual portions.
Cold Accumulation Block
A cold accumulation block is enclosed with the appliance.
In the event of power failure or a malfunction of the appliance, the
3
cold accumulation block will increase the hold over period by several
hours. The cold accumulation block cools best if it is placed in the top
drawer at the front on the frozen food. If the freezer section is only
partially filled, pack the frozen food together as tightly as possible, so
that in the event of a power cut the cold remains in the frozen food for
longer.
When freezing food, place the cold accumulation block on the already
frozen food to prevent defrosting due to the warmth of the food that is
being frozen.
When defrosting the appliance place the cold accumulation block on
top of the frozen food to keep it cold.
The block may also be used in a cool bag to keep the temperature of
food down during transportation.
Refer to the section "Prior to Initial Start-Up" regarding the freezing of
the cold accumulation block.
818 38 80-00/715
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.