AEG-Electrolux S60240KG28 User Manual

Page 1
SANTO 60240-28 KG
Kühl-Gefrierkombination
Fridge-Freezer
Gebrauchsanweisung
Instruction for use
Page 2
2
Sehr geehrte Kundin, sehr geehrter Kunde,
Bewahren Sie bitte die Gebrauchsanweisung zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter.
Hinweis: Diese Gebrauchsanweisung ist für mehrere technisch vergleichba­re Modelle mit unterschiedlicher Ausstattung bestimmt. Beachten Sie bitte nur die Hinweise, die Ihre Geräteausführung betreffen.
Mit dem Warndreieck und/oder durch Signalwörter (Warnung!, Vorsicht!, Achtung!) sind Hinweise hervorgehoben, die für Ihre Sicherheit oder für die Funktionsfähigkeit des Gerätes wichtig sind. Bitte unbedingt beachten.
Nach diesem Zeichen erhalten Sie ergänzende Informationen zur Bedie­nung und praktischen Anwendung des Gerätes.
Mit der Blume sind Tips und Hinweise zum wirtschaftlichen und umwelt­schonenden Einsatz des Gerätes gekennzeichnet.
Für evtl. auftretende Störungen enthält die Gebrauchsanweisung Hinweise zur selbständigen Behebung, siehe Abschnitt "Was tun, wenn ...". Sollten diese Hinweise nicht ausreichen, haben Sie jederzeit zwei Anlaufstellen, bei denen Ihnen weitergeholfen wird:
Wir sind für Sie da: montags bis freitags
8.00 bis 20.00 Uhr samstags
10.00 bis 14.00 Uhr.
Hier erhalten Sie Antwort auf jede Frage, die die Ausstattung und den Ein­satz Ihres Gerätes betrifft. Natürlich nehmen wir auch gerne Wünsche, Anregungen und Kritik entgegen. Unser Ziel ist es, zum Nutzen unserer Kun­den unsere Produkte und Dienstleistungen weiter zu verbessern.
Bei technischen Problemen steht Ihnen unser WERKSKUNDENDIENST in Ihrer Nähe jederzeit zur Verfügung (Adressen und Telefonnummern finden Sie im Verzeichnis Garantiebedingungen / Kundendienststellen).
Beachten Sie dazu den Abschnitt „Kundendienst“
*(Telekom 0,12 Euro/min.)
INFO SERVICES 0180 - 555 4 555*
Page 3
3
Inhalt
Sicherheit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Information zur Geräteverpackung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Entsorgung von Altgeräten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Transportschutz entfernen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Trasnportsicherungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Aufstellen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Aufstellort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ihr Kühlgerät braucht Luft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hintere Abstandstücke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Türanschlag wechseln . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Elektrischer Anschluß . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Vor Inbetriebnahme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Inbetriebnahme und Temperaturregelung . . . . . . . . . . . . . . . . . . . .11
Zusatzschalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Innenausstattung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Zusatzschalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Abstellflächen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Variable Innentür . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Richtig lagern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Einfrieren und Tiefkühllagern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Eiswürfel bereiten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Gefrierkalender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Kälte-akkus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Abtauen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Gerät abschalten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Reinigung und Pflege . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Tips zur Energie-Einsparung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Was tun, wenn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Abhilfe bei Störungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Lampe auswechseln . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Bestimmungen, Normen, Richtlinien . . . . . . . . . . . . . . . . . . . . . . . .20
3
Page 4
4
Sicherheit
Die Sicherheit unserer Kältegeräte entspricht den anerkannten Regeln der Technik und dem Gerätesicherheitsgesetz. Dennoch sehen wir uns veran­laßt, Sie mit folgenden Sicherheitshinweisen vertraut zu machen:
Bestimmungsgemäße Verwendung
• Das Kältegerät ist für die Verwendung im Haushalt bestimmt. Es eignet sich zum Kühlen, Einfrieren und Tiefkühllagern von Lebensmitteln sowie zur Eisbereitung. Wird das Gerät zweckentfremdet oder falsch bedient, kann vom Hersteller keine Haftung für eventuelle Schäden übernommen werden.
• Umbauten oder Veränderungen am Kältegerät sind aus Sicherheitsgrün­den nicht zulässig.
• Sollten Sie das Kältegerät gewerblich oder für andere Zwecke als zum Kühlen, Tiefkühllagern und Einfrieren von Lebensmitteln benutzen, be­achten Sie bitte die für Ihren Bereich gültigen gesetzlichen Bestimm­ungen.
Vor der ersten Inbetriebnahme
• Überprüfen Sie das Kältegerät auf Transportschäden. Ein beschädigtes Gerät auf keinen Fall anschließen! Wenden Sie sich im Schadensfall bitte an den Lieferanten.
Kältemittel
Das Gerät enthält im Kältemittelkreislauf das Kältemittel Isobutan (R600a), ein Naturgas mit hoher Umweltverträglichkeit, das jedoch brennbar ist.
• Achten Sie beim Transportieren und Aufstellen des Gerätes darauf, daß keine Teile des Kältemittelkreislaufs beschädigt werden.
• Bei Beschädigung des Kältemittelkreislaufs:
– offenes Feuer und Zündquellen unbedingt vermeiden; – den Raum, in dem das Gerät steht, gut durchlüften.
Sicherheit von Kindern
• Verpackungsteile (z. B. Folien, Styropor) können für Kinder gefährlich sein. Erstickungsgefahr! Verpackungsmaterial von Kindern fernhalten!
• Ausgediente Altgeräte bitte vor der Entsorgung unbrauchbar machen. Netzstecker ziehen, Netzkabel durchtrennen, eventuell vorhandene Sch­napp- oder Riegelschlösser entfernen oder zerstören. Dadurch verhindern Sie, daß sich spielende Kinder im Gerät einsperren (Erstickungsgefahr!)
Page 5
5
oder in andere lebensgefährliche Situationen geraten.
• Das Gerät darf von Kindern und Personen, deren physische, sensorische oder geistige Fähigkeiten sowie Mangel an Erfahrung und Kenntnissen einen sicheren Gebrauch des Gerätes ausschließen, nur unter Aufsicht oder nach entsprechender Einweisung durch eine Person benutzt werden, die sicherstellt, dass sie sich den Gefahren des Gebrauchs bewusst sind. Kinder sind zu beaufsichtigen, sodass sie nicht am Gerät spielen können.!
Im Alltagsbetrieb
• Behälter mit brennbaren Gasen oder Flüssigkeiten können durch Kälte­einwirkung undicht werden. Explosionsgefahr! Lagern Sie keine Behälter mit brennbaren Stoffen, wie z.B. Spraydosen, Feuerzeug-Nachfüllkar­tuschen etc. im Kältegerät.
• Flaschen und Dosen dürfen nicht in den Gefrierraum. Sie können sprin­gen, wenn der Inhalt gefriert - bei kohlensäurehaltigem Inhalt sogar explodieren! Legen Sie nie Limonaden, Säfte, Bier, Wein, Sekt usw. in den Gefrierraum. Ausnahme: Hochprozentige Spirituosen können im Gefrier­raum gelagert werden.
• Speiseeis und Eiswürfel nicht unmittelbar aus dem Gefrierraum in den Mund nehmen. Sehr kaltes Eis kann an Lippen oder Zunge festfrieren und Verletzungen verursachen.
• Tiefkühlgut nicht mit nassen Händen berühren. Die Hände könnten daran festfrieren.
• Keine Elektrogeräte (z. B. elektrische Eismaschinen, Rührgeräte etc.) im Kältegerät betreiben.
• Vor Reinigungsarbeiten das Gerät grundsätzlich abschalten und den Netz­stecker ziehen oder Sicherung in der Wohnung abschalten bzw. heraus­drehen.
• Netzstecker immer am Stecker aus der Steckdose ziehen, nie am Kabel.
Im Störungsfall
• Sollte einmal eine Störung am Gerät auftreten, sehen Sie bitte zuerst in dieser Gebrauchsanweisung unter "Was tun, wenn ..." nach. Falls die dort aufgeführten Hinweise nicht weiterhelfen, führen Sie bitte keine weite­ren Arbeiten selbst aus.
• Kältegeräte dürfen nur von Fachkräften repariert werden. Durch unsach­gemäße Reparaturen können erhebliche Gefahren entstehen. Wenden Sie sich im Reparaturfall bitte an Ihren Fachhändler oder an unseren Kun­dendienst.
Page 6
6
Transportschutz entfernen
Das Gerät sowie Teile der Innenausstattung sind für den Transport geschützt.
• Alle Klebebänder sowie Polsterteile aus dem Geräteinnenraum entfernen.
Entsorgung
Information zur Geräteverpackung
Alle verwendeten Werkstoffe sind umweltverträglich! Sie können gefahrlos deponiert oder in der Müllverbrennungsanlage verbrannt werden! Zu den Werkstoffen: Die Kunststoffe können auch wiederverwertet werden und sind folgendermaßen gekennzeichnet: >PE< für Polyäthylen, z. B. bei der äußeren Hülle und den Beuteln im Innern. >PS< für geschäumtes Polystyrol, z. B. bei den Polsterteilen, grundsätzlich FCKW-frei.
Die Kartonteile werden aus Altpapier hergestellt und sollten auch wieder zur Altpapiersammlung gegeben werden.
Entsorgung von Altgeräten
Aus Umweltschutzgründen müssen Kältegeräte fachgerecht entsorgt wer­den. Dies gilt für Ihr bisheriges Gerät und - nachdem es eines Tages ausge­dient hat - auch für Ihr neues Gerät.
Warnung! Ausgediente Altgeräte bitte vor der Entsorgung unbrauchbar machen. Netzstecker ziehen, Netzkabel durchtrennen, eventuell vorhande­ne Schnapp- oder Riegelschlösser entfernen oder zerstören. Dadurch verhindern Sie, daß sich spielende Kinder im Gerät einsperren (Erstickungs­gefahr!) oder in andere lebensgefährliche Situationen geraten.
Entsorgungshinweise:
• Das Gerät darf nicht mit dem Haus- oder Sperrmüll entsorgt werden.
• Der Kältemittelkreislauf, insbesondere der Wärmetauscher an der Geräte­rückseite, darf nicht beschädigt werden.
• Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einem Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefähr­det. Weitere Informationen über das Recycling dieses Produkts erhalten Sie von Ihrem Rathaus, Ihrer Müllabfuhr oder dem Geschäft, in dem Sie das Produkt gekauft haben.
Page 7
7
Aufstellen
Aufstellort
Das Gerät soll in einem gut belüfteten und trockenen Raum stehen. Die Umgebungstemperatur wirkt sich auf den Stromverbrauch aus. Daher
sollte das Gerät – nicht direkter Sonneneinstrahlung ausgesetzt sein; – nicht an Heizkörpern, neben einem Herd oder sonstigen Wärmequellen
stehen;
– nur an einem Ort stehen, dessen Umgebungstemperatur der Klimaklasse
entspricht, für die das Gerät ausgelegt ist.
Die Klimaklasse finden Sie auf dem Typschild, das sich links im Innenraum des Kühlraumes befindet.
Nachstehende Tabelle zeigt, welche Umgebungstemperatur welcher Klima­klasse zugeordnet ist:
Klimaklasse für Umgebungstemperatur von
SN +10 bis +32 °C
N +16 bis +32 °C
ST +18 bis +38 °C
T +18 bis +43 °C
Ist die Aufstellung neben einer Wärmequelle unvermeidbar, sind folgende seitliche Mindestabstände einzuhalten:
– zu Elektroherden 3 cm; – zu Öl- und Kohleherden 30 cm. Können diese Abstände nicht eingehalten werden, ist eine Wärmeschutz-
platte zwischen Herd und Kältegerät erforderlich. Steht das Kältegerät neben einem anderen Kühl- oder Gefriergerät, ist ein
seitlicher Abstand von 5 cm erforderlich, damit sich an den Geräte-Außen­seiten kein Schwitzwasser bildet.
B
A
Transportsicherungen
Ihr Gerät ist mit Transportsicherung versehen, die die Ablage während des Transportes sichern.
Entfernen Sie diese wie folgt: Ablagen hinten hochheben, in Pfeil-
richtung ziehen bis sich die Ablage löst und die Sicherungen entfernen.
Page 8
8
Türanschlag wechseln
Der Türanschlag kann von rechts (Lieferzustand) nach links gewechselt wer­den, falls der Aufstellort dies erfordert.
Warnung! Während des Türanschlagwechsels darf das Gerät nicht am Stromnetz angeschlossen sein. Vorher Netzstecker ziehen.
Ihr Kühlgerät braucht Luft
Aus Gründen der Sicherheit muß eine Mindestbelüftung gesichert sein, wie aus der Abb. hervorgeht:
Achtung: Die Lüftungs-Öffnungen müssen
immer saubergehalten werden. Damit die Luft zirkulieren kann, die Lüftungsöffnungen niemals Abdecken oder verstellen.
Hintere Abstandstücke
Das Gerät ist mit 2 Distanzstücken ausgestattet, die wie in der Abbil­dung gezeigt montiert werden müs­sen.
100 mm10 mm
10 mm
NP00
Page 9
9
Vorgehensweise
1. Sockelblende (D) nach vorn abziehen.
2. Türlagerabdeckung (F) von links nach rechts umsetzen.
3. Unteres Türlager (E) abschrauben.
4. Kühlraumtür nach unten abnehmen.
5. Mittleres Türlager (H) abschrauben.
6. Gefrierraumtür nach unten abnehmen.
7. Oberen Türlagerzapfen (D) abschrauben und auf gegenüber­liegenden Seite montieren.
8. Abdeckstöpsel für die Bohrlöcher von links nach rechts umsetzen.
9. Gefrierraumtür in oberen Tür­lagerzapfen einsetzen und schließen.
10. Mittleres Türlager (H) unten links in die Gefrierraumtür einsetzen und am Gehäuse festschrauben.
11. Kühlraumtür in mittleres Türlager einsetzen und schließen.
12. Unteres Türlager (E) unten links in die Kühlraumtür einsetzen und am Gehäuse festschrauben.
13. Sockelblende (D) aufsetzen.
14. Türgriffe abschrauben und auf gegenüberliegender Seite befestigen. Dazu mit einem Vorstecher die Plas­tikstöpsel auf der gegenüberliegen­den Seite vorsichtig in die Tür ein­schlagen. Mit den im Beipack enthal­tenen Plastikstöpseln die auf der alten Griffseite freigewordenen Löcher verschließen.
F
D
F
F
E
F
H
G
Page 10
10
Achtung:
Vergewissern Sie sich nach Aus­führung des Türanschlagwechsels, daß alle Schrauben fest angezogzen sind und die Türdichtung einwand­frei am Gehäuse anliegt.
Gegenfalls die Türdichtung vorsichtig mit einem Fön erwärmen (max.50°C) und von Hand in Form ziehen.
D162/a
Elektrischer Anschluß
Für den elektrischen Anschluß ist eine vorschriftsmäßig installierte Schutzkontakt-Steckdose erforderlich. Sie sollte so gesetzt sein, daß ein Ziehen des Netzsteckers möglich ist.
Die elektrische Absicherung muß mindestens 10/16 Ampere betragen. Ist die Steckdose bei eingebautem Gerät nicht mehr zugänglich, muß eine
geeignete Maßnahme in der Elektroinstallation sicherstellen, daß das Gerät vom Netz getrennt werden kann (z. B. Sicherung, LS-Schalter, Fehlerstrom­Schutzschalter oder dergleichen mit einer Kontaktöffnungsweite von min­destens 3 mm).
• Vor Inbetriebnahme am Typschild des Gerätes überprüfen, ob Anschluß­spannung und Stromart mit den Werten des Stromnetzes am Aufstellort übereinstimmen.
Z. B.: AC 220 ... 240 V 50 Hz oder
220 ... 240 V~ 50 Hz (d. h. 220 bis 240 Volt Wechselstrom, 50 Hertz) Das Typschild befindet sich links im Innenraum des Gerätes.
Vor Inbetriebnahme
• Das Geräteinnere und alle Ausstattungsteile bitte vor Erstinbetriebnahme
reinigen (siehe Abschnitt "Reinigung und Pflege").
Page 11
11
Inbetriebnahme und Temperaturregelung
• Netzstecker in die Steckdose stecken. Die Innenbeleuchtung leuchtet bei geöffneter Tür. Der Drehknopf für die Temperaturwahl ist im Kühlraum rechts.
Stellung „0“ bedeutet: aus. Stellung „1“ bedeutet: Höchste Innentemperatur (wärmste Einstellung). Stellung „6“ (Endanschlag) bedeutet: Tiefste Innentemperatur (kälteste
Einstellung). Folgende Einflüsse sind ausschlaggebend für die Innentemperatur: – Umgebungstemperatur; – Menge und Temperatur der eingelagerten Lebensmittel; – Häufiges oder langes Öffnen der Tür. Die Temperaturen im Kühlraum und Gefrierraum lassen sich nicht getrennt
regeln. Sollten frische Lebensmittel schnell eingefroren werden, kann Stellung „6“
gewählt werden. Achten Sie darauf, daß die Temperatur im Kühlraum nicht unter 0°C absinkt und stellen Sie den Temperaturreg-ler rechtzeitig auf Stel­lung „3“ oder „4“ zurück.
Wichtig!
Hohe Umgebungstemperatur (z. B. an heißen Sommertagen) und kalte Ein­stellung des Temperaturreglers (Stellung „5“ bis „6“) kann zu Dauerbetrieb des Kompressors führen.
In diesem Fall den Temperaturregler auf eine wärmere Einstellung zurück­drehen (Stellung „3“ bis „4“). Bei dieser Einstellung wird der Kompressor geregelt und der Abtauvorgang wieder automatisch eingeleitet.
Zusatzschalter
Steht das Gerät in einem Raum, in dem die Temperatur weniger als 16°C beträgt, müssen sie den Zusatzschalter (A) betätigen. Die eingebaute Kontrollanzeige leu­chtet auf.
D710
A
Page 12
12
Innenausstattung
Abstellflächen
Die Abstellfläche aus Glas über den Obst- und Gemüseschalen muß immer in dieser Stellung verbleiben, damit Obst und Gemüse länger frisch bleiben. Die übrigen Abstellflächen sind höhenverstellbar.
Dazu die Abstellfläche soweit nach vorne ziehen, bis sie sich nach oben oder unten abschwenken und herausnehmen läßt.
Das Einsetzen in eine andere Höhe bitte in umgekehrter Reihenfolge vor­nehmen.
Hohes Kühlgut einstellen: Die vordere Hälfte der zweiteiligen Glasabstellfläche herausnehmen und in
eine andere Ebene einschieben. Dadurch gewinnen Sie Raum, um auf der darunterliegenden Abstellfläche hohes Kühlgut abzustellen
Variable Innentür
Je nach Erfordernis können die Abstellfächer der Kühlraumtür nach oben herausgenommen und in andere Aufnahmen umgesetzt werden.
D338
Page 13
13
Einfrieren und Tiefkühllagern
Im Gefrierraum können Sie Tiefkühlkost lagern und frische Lebens-mittel einfrieren.
Achtung!
• Vor dem Einfrieren von Lebensmitteln muß die Temperatur im Gefrier­raum -18 °C oder kälter sein.
• Bitte das auf dem Typschild angegebene Gefriervermögen beachten. Das Gefriervermögen ist die maximale Menge an frischer Ware, die innerhalb von 24 Stunden eingefroren werden kann. Wenn Sie an mehreren Tagen hintereinander einfrieren, nehmen Sie bitte nur 2/3 bis 3/4 der auf dem Typschild angegebenen Menge. Sie erreichen eine bessere Qualität, wenn die Lebensmittel schnell bis zum Kern durchgefroren werden.
• Warme Lebensmittel vor dem Einfrieren abkühlen lassen. Die Wärme führt zu verstärkter Eisbildung und erhöht den Energieverbrauch.
Richtig lagern
Um die Lebensmittel möglichst lange frisch zu halten, beachten Sie bitte folgendes:
• Keine warmen Speisen oder Flüssigkeiten in den Kühlschrank einstellen.
• Die Lebensmittel sollten abgedeckt oder eingewickelt werden.
• Die Lebensmittel müssen so eingelagert werden, daß die Luft frei zirkulie­ren kann.
Nachstehend einige praktische Ratschläge: Fleisch (alle Sorten) in Plastikfolie einpacken und auf die Glasplatte, die
sich über der Gemüseschale (über den Gemüseschalen) befindet, legen.
In dieser Lage kann das Fleisch längstens 1-2 Tage aufbewahrt werden. Gekochte Nahrungsmittel, kalte Platten, usw. zugedeckt aufbewahren.
Sie können auf jede beliebige Ablage gelegt werden. Obst und Gemüse: nach vorherigem Säubern und Waschen in der Gemü-
seschale aufbewahren Butter und Käse: in speziellen Behältern aufbewahren oder in Alu-bzw.
Plastikfolie einpacken, um den Kontakt mit der Luft zu vermeiden. Milch in Flaschen: gut verschlossen in das Flaschenfach an der Innentür
stellen
Banane, Kartoffeln, Zwiebeln und Knoblauch sollten nicht unverpackt im Kühlschrank aufbewahrt werden.
Page 14
14
Eiswürfel bereiten
1. Eiswürfelschale zu 3/4 mit kaltem Wasser füllen, in den Gefrierraum stellen und gefrieren lassen.
2. Zum Herauslösen der fertigen Eiswürfel die Eiswürfelschale verwinden oder kurz unter fließendes Wasser halten.
Achtung! Eine eventuell angefrorene Eiswürfelschale keinesfalls mit spitzen oder scharfkantigen Gegenständen ablösen, sonst besteht die Gefahr, daß der Kältekreislauf beschädigt wird. Verwenden Sie den beiliegenden Kunst­stoffschaber.
• Auf die Lagerzeit bzw. auf das Haltbarkeitsdatum von gekauften Tiefkühl-
produkten achten
• Einmal aufgetaute Lebensmittel ohne weitere Verarbeitung (garen zu Fer-
tiggerichten) auf keinen Fall ein zweites Mal einfrieren.
• Behälter mit brennbaren Gasen oder Flüssigkeiten können durch Käl-
teeinwirkung undicht werden. Explosionsgefahr! Lagern Sie keine Behäl­ter mit brennbaren Stoffen, wie z.B. Spraydosen, Feuerzeug-Nachfüllkar­tuschen etc. im Kältegerät.
• Flaschen und Dosen dürfen nicht in den Gefrierraum. Sie können sprin-
gen, wenn der Inhalt gefriert - bei kohlensäurehaltigem Inhalt sogar explodieren! Legen Sie nie Limonaden, Säfte, Bier, Wein, Sekt usw. in den Gefrierraum. Ausnahme: Hochprozentige Spirituosen können im Gefrier­raum gelagert werden.
• Alle Lebensmittel vor dem Einfrieren luftdicht verpacken, damit sie nicht
austrocknen, nicht den Geschmack verlieren und keine Geschmacksüber­tragung auf anderes Tiefkühlgut erfolgen kann.
Vorsicht! Tiefkühlgut nicht mit nassen Händen berühren. Die Hände könn­ten daran festfrieren.
1. Wenn Sie schnelles Einfrieren von Gefriergut wünschen, oder wenn Sie das max. Gefriervermögen ausnutzen wollen, müssen Sie den Zusatzschalter 3 Stunden vor dem Einlegen des Gefriergutes betätigen. Vergessen Sie nicht, nach dem Ende des Einfriervorganges den Schalter erneut zu betätigen. Sie vermeiden damit unnötigen Energieverbrauch.
2. Legen Sie die verpackten Lebensmittel zum Einfrieren in die oberste Schu­blade. Nicht gefrorene Ware darf bereits gefrorene Ware nicht berühren, die gefrorene Ware kann sonst antauen.
3. Tür so wenig wie möglich öffnen und nicht offen lassen.
Page 15
15
Gefrierkalender
• Die Symbole auf den Schubladen zeigen unterschiedliche Arten von Tiefkühlgut.
• Die Zahlen geben für die jeweilige Art von Tiefkühlgut die Lagerzeit in Monaten an. Ob der obere oder der untere Wert der angegebenen Lager­zeiten gültig ist, hängt von der Qualität der Lebensmittel und deren Vor­behandlung vor dem Einfrieren ab. Für Lebensmittel mit hohem Fettanteil gilt immer der untere Wert..
Abtauen
Kühlraum
Die Rückwand des Kühlraums bereift, während der Kompressor läuft, und taut vollautomatisch ab, wärend der Kompressor stillsteht..
Das Tauwasser wird in der Ablaufrin­ne an der Rückwand des Kühlraumes aufgefangen, durch das Ablaufloch in die Auffangschale am Kompressor geleitet und dort verdunstet..
Wir empfehlen, das in der Mitte der Abtauwasserrinne des Kühlraumes befindliche Ablaufloch für das Abtauwasser regelmäßig zu reinigen, um zu vermeiden, daß das Abtauwasser auf Lebensmittel tropft.
Verwenden Sie den dafür vorgesehe­nen Reiniger, der sich schon im Ablaufloch befindet.
Kälteakkus
Das Gerät ist mit zwei Kälteakkus ausgestattet. Zum Einfrieren der Kälteakkus bitte Abschnitt "Vor Inbetriebnahme" beach-
ten. Bei Stromausfall oder einer Störung am Gerät verlängert die Kälteakkus die
Zeit bis zur unzulässigen Erwärmung des Gefrierguts um mehrere Stunden. Diese Aufgabe erfüllen die Kälteakkus nur dann optimal, wenn sie in der
obersten Schublade vorne oben auf dem Gefriergut eingelegt wird. Die Kälteakkus können Sie vorübergehend auch als Kühlelement für Kühl-
taschen verwenden.
D037
Page 16
16
Gerät abschalten
Soll das Gerät für längere Zeit außer Betrieb genommen werden:
1. Kühl- und Gefriergut sowie Eisschalen herausnehmen.
2. Gerät abschalten, dazu Temperaturregler auf Stellung „0“ drehen.
3. Netzstecker ziehen oder Sicherung abschalten bzw. herausdrehen.
4. Kühl- und Gefrierraum abtauen und gründlich reinigen (siehe Abschnitt "Reinigung und Pflege").
5. Türen offen lassen, um Geruchsbildung zu vermeiden.
Gefrierraum
Im Gefrierraum schlägt sich während des Betriebs und beim Öffnen der Tür Feuchtigkeit als Reif nieder. Entfernen Sie diesen Reif von Zeit zu Zeit mit dem beiliegenden Kunststoffschaber.
Starke Reifbildung im Gefrierraum erhöht den Energieverbrauch. Deshalb soll abgetaut werden, wenn die Reifsicht eine Dicke von ca. 4 Millimeter erreicht hat; mindestens jedoch einmal im Jahr. Ein geeigneter Zeitpunkt zum Abtauen ist auch immer dann, wenn das Gerät leer oder nur wenig beladen ist Um ein vollständiges Abtauen durchzuführen, geht man wie folgt vor:
1. Tiefkühlgut herausnehmen, in meh­rere Lagen Zeitungspapier einpacken und abgedeckt an einem kühlen Ort lagern.
2. Gerät abschalten und den Netz­stecker ziehen oder Sicherung abschalten bzw. herausdrehen.
3. Gefrierraumtür geöffnet lassen.
4. Kunstoffschaber als Tauwasserablauf in den Schlitz unterhalb der Tauwas­serablaufrinne stecken und Auffang­schale unterstellen.
5. Plastikschaber für späteren Gebrauch aufbewahren.
6. Nach Beendigung des Abtauvorganges Netzstecker wieder einstecken und­Temperaturregler auf die gewünschte Position einstellen.
Achtung:
Keinesfalls harte oder spitze Metallgegenstände zum Entfernen von Reif oder Eis benutzen.
Verwenden Sie keine elektrischen Heiz- oder Wärmegeräte und keine anderen mechanischen oder künstlichen Hilfsmittel, um den Abtauvor­gang zu beschleunigen, mit Ausnahme der in dieser Gebrauchsanweisung empfohlenen. Ein Temperaturanstieg der Tiefkühlkost während des Abtauens könnte die Aufbewahrungsdauer verkürzen.
D068
Page 17
17
Reinigung und Pflege
Aus hygienischen Gründen sollte das Geräteinnere, einschließlich Innenaus­stattung, regelmäßig gereinigt werden.
Warnung!
• Das Gerät darf während der Reinigung nicht am Stromnetz angeschlos­sen sein. Stromschlaggefahr! Vor Reinigungsarbeiten Gerät abschalten und Netzstecker ziehen oder Sicherung abschalten bzw. herausdrehen.
• Das Gerät nie mit Dampfreinigungsgeräten reinigen. Feuchtigkeit könnte in elektrische Bauteile gelangen, Stromschlaggefahr! Heißer Dampf kann zu Schäden an Kunststoffteilen führen.
• Das Gerät muß trocken sein, bevor Sie es wieder in Betrieb nehmen.
Achtung!
• Ätherische Öle und organische Lösungsmittel können Kunststoffteile angreifen, z. B.
– Saft von Zitronen- oder Apfelsinenschalen; – Buttersäure; – Reinigungsmittel, die Essigsäure enthalten. Solche Substanzen nicht mit den Geräteteilen in Kontakt bringen.
• Keine scheuernden Reinigungsmittel verwenden.
1. Kühl- und Tiefkühlgut herausnehmen. Tiefkühlgut in mehrere Lagen Zei­tungspapier einpacken. Alles abgedeckt an einem kühlen Ort lagern.
2. Gefrierfach vor dem Reinigen abtauen (siehe Abschnitt "Abtauen").
3. Gerät abschalten und den Netzstecker ziehen oder Sicherung abschalten bzw. herausdrehen.
4. Gerät einschließlich Innenausstattung mit einem Lappen und lauwar-mem Wasser reinigen. Eventuell etwas handelsübliches Geschirrspülmittel beige­ben.
5. Anschließend mit klarem Wasser nachwischen und trockenreiben. Staubablagerungen am Verflüssiger erhöhen den Energieverbrauch. Deshalb
einmal im Jahr den Verflüssiger an der Geräterückseite mit einer weichen Bürste oder mit dem Staubsauger vorsichtig reinigen.
6. Die Ablauföffnung der Tropfrinne an der Rückwand des Kühlraumes kon­trollieren. Bei Verstopfung diese mit Hilfe des grünen Stöpsels frei machen.
7. Nachdem alles trocken ist, Lebensmittel wieder einlagern und Gerät wieder in Betrieb nehmen.
Page 18
18
Was tun, wenn ...
Abhilfe bei Störungen
Möglicherweise handelt es sich bei einer Störung nur um einen kleinen Feh­ler, den Sie anhand nachfolgender Hinweise selbst beheben können. Führen Sie keine weiteren Arbeiten selbst aus, wenn nachstehende Informationen im konkreten Fall nicht weiterhelfen.
Warnung! Reparaturen am Kältegerät dürfen nur von Fachkräften durch­geführt werden. Durch unsachgemäße Reparaturen können erhebliche Gefahren für den Benutzer entstehen. Wenden Sie sich im Reparaturfall an Ihren Fachhändler oder an unseren Kundendienst.
Störung Mögliche Ursache Abhilfe
Gerät arbeitet nicht
Gerät ist nicht eingeschaltet Gerät einschalten. Netzstecker ist nicht einge-
steckt oder lose.
Netzstecker einstecken.
Sicherung hat ausgelöst oder ist defekt.
Sicherung überprüfen, gege­benenfalls erneuern.
Steckdose ist defekt.
Störungen am Stromnetz behebt Ihr Elektrofachmann.
Tips zur Energie-Einsparung
• Das Gerät nicht in der Nähe von Herden, Heizkörpern oder anderen Wär­mequellen aufstellen. Bei hoher Umgebungstemperatur läuft der Kom­pressor häufiger und länger.
• Ausreichende Be- und Entlüftung des Gerätes gewährleisten. Lüftung­söffnungen niemals abdecken.
• Keine warmen Speisen in das Gerät stellen. Warme Speisen erst abkühlen lassen.
• Tür nur so lange wie nötig geöffnet lassen.
• Die Temperatur nicht kälter als nötig einstellen.
• Tiefkühlgut zum Auftauen in den Kühlraum legen. Die Kälte im Tiefkühl­gut wird so zur Kühlung im Kühlraum genutzt.
• Den Verflüssiger, das Metallgitter an der Geräterückseite, immer sauber halten.
Page 19
19
Die Lebensmittel sind zu warm.
Innenbeleuchtung funktion­iert nicht
Das Gerät steht neben einer Wärmequelle.
Temperatur ist nicht richtig eingestellt.
Bitte im Abschnitt "Inbe­triebnahme" nachsehen.
Lampe ist defekt.
Bitte im Abschnitt "Lampe auswechseln" nachsehen.
Temperaturregler vorüber­gehend auf kältere Einstel­lung drehen.
Tür war längere Zeit geöff­net.
Bitte im Abschnitt "Aufstell­ort" nachsehen.
Innerhalb der letzten 24 Stunden wurden größere Mengen warmer Lebensmittel eingelagert.
Tür nur so lange wie nötig geöffnet lassen.
Gerät kühlt zu stark. Temperatur ist zu kalt gestellt.
Temperaturregler vorüber­gehend auf wärmere Einstel­lung drehen.
Störung Mögliche Ursache Abhilfe
Der Kompressor läuft nach einiger Zeit selbsttätig an.
Siehe Abschnitt „Reinigung und Pflege“
Dies ist normal, es liegt keine Störung vor.
Nach Änderung der Tem­peratureinstellung läuf der Kompressor nicht sofort an. Wasser am Kühlraumboden oder auf Abstellflächen.
Tauwasser-Ablaufloch ist ver­stopft.
Starke Reifbildung im Gerät, evtl. auch an der Türdichtung.
Türdichtung ist undicht (evtl. nach Türanschlagwechsel).
An den undichten Stellen Tür­dichtung vorsichtig mit einem Haartrockner erwärmen (nicht wärmer als ca. 50 °C). Gleich­zeitig die erwärmte Türdich­tung von Hand so in Form ziehen, daß sie wieder einwandfrei anliegt.
Ungewöhnliche Geräusche.
Gerät hat Kontakt mit der Wand oder mit anderen Gegenständen.
Gerät steht nicht gerade.
Ein Teil, z. B. ein Rohr, an der Geräterückseite berührt ein anderes Geräteteil oder die Wand.
Gegebenenfalls dieses Teil vorsichtig wegbiegen.
Gerät etwas wegrücken.
Verstellfüße nachjustieren.
Page 20
Bestimmungen, Normen, Richtlinien
Das Kältegerät ist für den Haushalt bestimmt und wurde unter Beachtung der für diese Geräte geltenden Normen hergestellt.
Bei der Fertigung wurden insbesondere die nach dem Gerätesicherheitsgesetz (GSG), der Unfallverhütungsvorschrift für Kälteanlagen (VBG 20) und den Bestimmungen des Verbandes Deutscher Elektrotechniker (VDE) notwendigen Maßnahmen getroffen. Der Kältekreislauf wurde auf Dichtheit geprüft.
Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.2.1973 - Niederspannungsrichtlinie – 89/336/EWG vom 3.5.1989 (einschließlich Änderungsrichtlinie
92/31/EWG) - EMV-Richtlinie
20
Lampe auswechseln
Warnung! Stromschlaggefahr! Vor dem Lampenwechsel Gerät abschalten und den Netzstecker ziehen oder Sicherung abschalten bzw. herausdrehen.
Lampendaten: 220-240 V, max. 15 W, Fassung: E 14
1. Zum Abschalten des Gerätes Tempera­turregler auf Stellung „0“ drehen.
2. Netzstecker ziehen.
3. Zum Auswechseln der Lampe Befestig­ungsschraube herausdrehen.
4. Gemäß Abbildung auf die Lampen­abdeckung drücken und diese nach hin­ten abschieben.
5. Defekte Lampe auswechseln.
6. Lampenabdeckung wieder einsetzen und Befestigungsschraube eindrehen.
7. Gerät wieder in Betrieb nehmen.
D411
Page 21
21
Dear customer,
Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.
Notes which are important for your safety or for the proper functioning of the appliance are stressed with a warning triangle and/or with signal words (Warning!, Caution!, Attention!). Please observe the following carefully.
Tips and notes concerning economical and environmentally sound use of the appliance are marked with the flower.
The operating instructions contain instructions for the correction of possi­ble malfunctions by the user in the section "What to do if ...". If these instructions should not be sufficient, our customer service department is always available to you.
Page 22
22
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Shelf holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Your refrigerator needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Rear spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Rehingeing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Starting up and temperature regulation . . . . . . . . . . . . . . . . . . . . .29
Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Storage shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Variable Inner door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Fresh food refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Freezing and storing frozen food . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Preparation of Ice Cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Freezing Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
What to do if . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .39
Page 23
23
Safety
The safety aspects of our refrigerators/freezers comply with accepted tech­nical standards and the German Appliance Safety Law. Nevertheless, we consider it our obligation to make you aware of the following safety infor­mation:
Intended use
• The refrigerator is intended for use in the home. It is suitable for the coo­ling, freezing and storing of frozen food, as well as for making ice. If the appliance is used for purposes other than those intended or used incor­rectly, no liability can be accepted by the manufacturer for any damage that may be caused.
• Alterations or changes to the freezer are not permitted for reasons of safety.
• If you use the refrigerator in a commercial application or forpurposes other than the cooling, freezing or frozen storage of foods,please obser­ve all valid legal regulations for your application.
Prior to initial start–up
• Check the refrigerator for transport damage. Under no circumstance
should a damaged appliance be plugged in! In the event of damage, please contact the vendor.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compa­tibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become dama­ged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition; – thoroughly ventilate the room in which the appliance is situated.
Safety of children
• Packaging (e.g. wraps, polystyrene) can be dangerous for children. There is a risk of suffocation! Keep packaging material away from children!
• Please make old appliances unusable prior to disposal. Pull out the mains plug, cut off the mains cable, break or remove spring or boltcatches, if fit-
Page 24
24
ted. By doing this you ensure that children cannot lock themselves in the fridge when playing (there is risk of suffocation!)or get themselves into other dangerous situations.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction con­cerning use of the appliance by a person responsible for their safety. Chil­dren should be supervised to ensure that they do not play with the appliance. !
Daily Operation
• Containers with flammable gases or liquids can leak at low temperatures. There is a risk of an explosion! Do not store any containers with flamma­ble materials such as, for example, spray cans, fire extinguisher refill car­tridges etc in the refrigerator/freezer.
• Bottles and cans must not be placed in the freezer compartment. They can burst when the contents freeze, high carbonate content drinks can even explode! Never store lemonade, juices, beer, wine, sparkling wine etc. in the freezer compartment. Exception: high alcohol content spirits can be stored in the freezer compartment.
• Do not put ice creams or ice cubes in the mouth immediately after remo­val from the freezer compartment. Very cold ice can freeze to the lips or tongue and cause injury.
• Do not touch frozen food with wet hands. Your hands could freeze to the food.
• Do not operate any electrical appliances in the refrigerator/freezer (e.g. electric ice cream makers, mixers etc.).
• Before cleaning the appliance, always switch off the appliance and unplug it, or pull the house fuse or switch off the circuit breaker.
• When unplugging always pull the plug from the mains socket, do not pull on the cable.
In case of malfunction
• If the a malfunction occurs on the appliance, please look first in the "What to do if ..." section of these instructions. If the information given there does not help, please do not perform any further repairs yourself.
• Refrigerators/freezers may only be repaired by qualified service engineers. Improper repairs can give rise to significant hazards. If your appliance needs repairing, please contact your specialist dealer or our Customer Service.
Page 25
25
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be dumped or burned at an incinerating plant without danger! About the materials: The plastics can be recycled and are identified as fol­lows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluo­rocarbon.
The carton parts are made from recycled paper and should be disposed of at a waste-paper recycling collection location.
Disposal of old Appliances
For environmental reasons, refrigeration appliances must be disposed of properly. This applies to your old appliance, and - at the end of its service life - for your new appliance as well.
Warning! Before disposing of old appliances make them inoperable. Remo­ve plug from mains, sever the power cable, remove or destroy any snap or latch closures. This eliminates the danger that playing children lock them­selves into the appliance (danger of suffocation!) or place themselves into other life-endangering situations.
Disposal
• The appliance may not be disposed of with domestic waste or bulky refu­se.
• The refrigerant circuit, especially the heat exchanger at the back of the appliance, may not be damaged.
• The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative con­sequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this pro­duct. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Remove transport safeguard
The appliance and the interior fittings are protected for transport.
• Remove all adhesive tape and packing pieces from the interior of the appliance.
Page 26
26
Installation
Installation Location
The appliance should be set up in a well ventilated, dry room. Energy use is affected by the ambient temperature. The appliance should
therefore – not be exposed to direct sunlight; – not be installed next to radiators, cookers or other sources of heat; – only be installed at a location whose ambient temperature corresponds to
the climate classification, for which the appliance is designed.
The climate classification can be found on the serial plate, which is located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for each climate classification:
Climate classification for an ambient temperature of
SN +10 bis +32 °C
N +16 bis +32 °C
ST +18 bis +38 °C
T +18 bis +43 °C
If installation next to a source of heat is unavoidable, the following minimum clearances must be maintained at the sides of the appliance:
– for electric cookers 3 cm; – for oil and coal fired ranges 30 cm.
If these clearances cannot be maintained a heat insulating pad is required between the cooker and the refrigeration appliance.
If the refrigeration appliance is installed next to another refrigerator or free­zer a clearance of 5 cm at the sides is required, in order to prevent the for­mation of condensation on the outside of the appliance.
B
A
Shelf holders
Your appliance is equipped with shelf retainers that make it possible to secure the shelves during transporta­tion.
To remove them proceed as follows: Raise the shelf from the back, push it in the direction of the arrow until it is freed and remove the retainers.
Page 27
27
Your appliance needs air
Air flows in from under the door, at the front, and flows out upwards, over the back. For cor­rect air circulation, it is important that the ventilation openings are not covered or obstructed.
Important! If the appliance is positioned under a kitchen wall unit, a minimum clearance of 10 cm must be left between the top of the appliance and the overhanging wall unit..
Rear spacers
Inside the applaince you find two spacers which must be fitted.
Slacken the screws and insert the spacer under the screw head, then re-tighten the screws.
Rehingeing the door
The side at which the door opens can be changed from the right side (fac­tory adjustment) to the left side, if the installation site requires.
Warning! When changing the side at which the door opens, the appliance may not be connected to the mains. Remove plug from the mains before hand.
Proceed as follow:
1. Remove the clip-in ventilation grille (D).
2. Remove the bottom hinge (E) by unscrewing the two fixing screws.
F
D
PR185
F
F
E
F
100 mm10 mm
10 mm
NP00
Page 28
28
3. Slide the bottom door off the centre hinge (H).
4. Remove the centre hinge and slide the top door off pin (D); unscrew pin (D) and refit it on the opposite side.
5. Remove the two plugs, to reveal the holes for the hinge pivots, and remount them on the other side.
6. Refit the top door and the centre hinge (H) on the opposite side.
7. Refit the bottom door.
8. Refit bottom hinge (E) on the oppo­site side, using the two screws pre­viously removed.
9. Remove blanking cover (F) from ven­tilation grille (D) by pushing it in the direction of the arrow and refit it on the opposite side.
10. Refit ventilation grille (D), clipping it into place.
11. Unscrew the handle. Refit it on opposite side after having pierced the plugs with a punch. Cover the holes left open with the plugs con­tained in the documentation pack.
Attention: After having reversed the opening
direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient tempe­rature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. in that case, wait for the natural fitting of the gasket or acce­lerate this process by heating up the part involved with a normal hairdrier.
D162/a
H
G
Page 29
29
Electrical connection
Before initial start-up, refer to the appliance rating plate to ascertain if sup­ply voltage and current values correspond with those of the mains at the installation location.
e.g.: AC 220 ... 240 V 50 Hz or
220 ... 240 V~ 50 Hz (i.e. 220 to 240 volts alternating current, 50 Hertz) The rating plate is inside the appliance on the left. A correctly installed, earthed socket is required for the electrical supply. The
supply must have a fuse rating of at least 10 Amps. If the socket is not accessible once the appliance is built in, the electrical
installation must include suitable means of isolating the appliance from the mains (e.g. fuse, cut-out, current trip or similar with a minimum contact separation of 3 mm).
Attention: The mains connection cable may only be replaced by a skilled electrician. Please contact your dealer or our customer service department for repairs.
Prior to Initial Start–Up
• Please clean the appliance interior and all accessories prior to initial start-
up (see section: “Cleaning and Care”).
Starting up and temperature regulation
• Insert the plug of the connection lead into the plug socket with protecti-
ve earth contact. When the refrigerator compartment door is opened, the internal lighting is switched on. The temperature selector knob is located on the RH side of the refrigerator compartment.
Setting „0“ means: Off. Setting „1“ means: Hightest temperature, (warmest setting). Setting „6“ (end-stop) means: Lowest temperature, (coldest setting).
However, the exact setting should be chosen keeping in the mind that the temperature inside the refrigerator depends on:
-the quantity of food stored
-how often the door is opened
Page 30
30
The temperatures in the refrigerator compartment and freezer co partment cannot be independently regulated.
If you want the freeze fresh food rapidly, select setting „6“, ensuring that the temperature in the refrigerator compartment does not drop blow 0°C. You should also promptly reset the temperature regulator to setting „3“ or „4“.
Important!
High ambient temperatures (e.g. on hot summer days) and a cold setting on the temperature regulator (position"5" to "6") can cause the compressor to run continuously.
If this happens, turn the temperature regulator back to a warmer setting (position "3" to "4"). At this setting the compressor will be switched on and off as usual and automatic defrosting recommenced.
Ambient Temperature switch
With a room temperature below +16°C the refrigerator compartment may not function correctly. If the room temperature is lower than +16°C it will be necessary to depress switch (A). The relevant pilot light comes on.
Interior Accessories
Storage Shelves
The glass shelf above the fruit and vegetable compartment should always remain in position, to ensure fruit and vegetables stay fresh lon­ger.
The remaining storage shelves can be adjusted to various heights:
Pull the storage shelf forward until it can be tipped up or down and remo­ved.
D710
A
D338
Page 31
31
To insert at a different height use the same procedure in reverse. Adjustment for tall goods: Remove the front half of the two-part vario glass storage shelf and insert it
at a different level. Space is thus gained for storage of tall goods on the underlying storage shelf.
Variable Inner Door
The door compartments can be pulled up and removed, and inserted at other positions as needed.
Fresh food refrigeration
To obtain the best performance:
• do not store warm food or evaporating liquide in the refrigeator
• do cover or wrap the food, particularly if it has a strong flavour.
• Position food so that air can circuiate freely round it.
Useful hints: Meat (all types): wrap in polythene bags and place on the glass shelf above
the vegetable drawer(s)For safety, store in this way only one or two days
at the most. Cooked foods, cold dishes, etc: these should be covered and may be placed
on any shelf. Fruit and vegetables: these should be thoroughly cleaned and placed in the
special drawer(s) provided. Butter and cheese: these should be placed in special airtight containers or
wapped in aluminium foil or polythene bags to exclude as much air as pos­sible.
Milk bootles: these should have a cap and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
Page 32
32
Freezing and storing frozen food
You can use your freezer for freezing fresh food yourself.
Important!
• The temperature in the freezer compartment must be –18 °C or colder before freezing food.
• Please observe the freezing capacity given on the rating plate. The freezing capacity is the maximum quantity of fresh food that can be frozen within a period of 24 hours. If you wish to freeze food several days in a row, please observe a maximum capacity of only 2/3 to 3/4 of that on the rating plate. The quality of the food is best preserved when it is frozen right through to the core as quickly as possible.
• Allow warm food to cool down before freezing. The warmth will cause increased ice formation and increase the power consumption.
• Please note the maximum storage times specified by the manufacturer.
• Thawed foods which have not been processed further (cooked into meals) may not under any circumstances be frozen a second time.
• Containers with flammable gases or liquids can leak at low temperatures. There is a risk of an explosion! Do not store any containers with flamma­ble materials such as, for example, spray cans, fire extinguisher refill car­tridges etc in the refrigerator/freezer.
• Bottles and cans must not be placed in the freezer. They can burst when the contents freeze, high carbonate content drinks can even explode! Never store lemonade, juices, beer, wine, sparkling wine etc. in the free­zer. Exception: high alcohol content spirits can be stored in the freezer.
• All foods must be packed air tight prior to freezing, so that they do not dry out or lose their flavour, and so that no flavour contamination of other frozen goods occurs.
Caution! Do not touch frozen food with wet hands. Your hands could free­ze to the food.
1. To achieve faster freezing of food or to freeze the maximum allowed quan­tity, depress the ambient switch 3 hours before loading the food without modifying the thermostat setting.
2. Place the food to be frozen in the top drawer.
3. Not open the door frequently or leave it open longer than absolutely neces­sary.
Page 33
33
Preparation of Ice Cubes
1. Fill the ice cube tray 3/4 full with cold water, place it in the freezer com­partment and leave to freeze.
2. To loosen the frozen cubes, either bend the ice cube tray or hold it under running water for a few seconds.
Important! Never try to free an ice tray that is frozen to the freezer com­partment using pointed or sharp edged objects.
Freezing Calendar
• The symbols show different types of frozen goods.
• The numbers indicate storage times in months for the appropriate types of frozen goods. Whether the upper or lower value of the indicated stora­ge time is valid depends on the quality of the foods and pre-treating befo­re freezing. The lower value applies to foods with high fat content.
Defrosting
Refrigerator
Frost is automatically eliminated from the evaporator of the refrig­erator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor com­pressor, where it evaporates.
D037
Page 34
34
We particulary recommend that you peridically clean the defrost-water drainage outlet, located in the center of the drainage groove in the refrige­rator compartment, to prevent the defrost water form overflowing on to foods stored in the compartment. Use a special cleaner provided, which you will find already inserted into the discharge hole.
Freezer
The freezer compartment, however, will become progrssively covered with frost. This should be removed with the special plastic scraper provided, whe­never the tickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs.
However when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows:
1. Remove the frozen food from the freezer, wrap it in several layers of new­spaper and put it in a very cool place.
2. Switch off the appliance and pull out the plug, or remove or unscrew the safety fuses.
3. Leave the freezer compartment door open.
4. Insert the plastic scraper into the recess provided under the defrost water channel and place a collecting basin under it.
5. Once defrosting is completed keep the scraper for future use;
6. Turn the thermostat knob to the required setting or replace the plug in the power socket.
Warning!
Never use metal tools to scrape off the frost Do not use a mechanical device or any artificial means to speed up the
thawing process other than those recommended by the manufacturer. A temperature rise of the frozen food packs, during defrosting , may shor-
ten their safe storage life.
D068
Page 35
35
Switching off the appliance
If the appliance is not going to be used for an extended period:
1. Remove all refrigerated and deep-frozen packages as well as ice trays.
2. Switch off the appliance by turning the temperature regulator to position "0".
3. Remove the mains plug or switch off or turn out the circuit breaker or fuse.
4. Defrost freezer compartment and clean thoroughly (see section: “Cleaning and Care”).
5. Leave the door open to avoid the build up of odours.
Cleaning and Care
For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.
Warning!
• The appliance may not be connected to the mains during cleaning. Dan­ger of electrical shock! Before cleaning switch the appliance offand rem ve the plug from the mains, or switch off or turn out the circuit breaker or fuse.
• Never clean the appliance with a steam cleaner. Moisture could accumu-
late in electrical components, danger of electrical shock! Hot vapours can lead to the damage of plastic parts.
• The appliance must be dry before it is placed back into service.
Attention!
• Ethereal oils and organic solvents can attack plastic parts, e.g. – lemon juice or the juice from orange peals; – butyric acid; – cleansers which contain acetic acid. Do not allow such substances to come into contact with appliance parts.
• Do not use any abrasive cleansers.
1. Remove frozen food and the food from the refrigerator. Wrap frozen food in several layers of newspaper. Store it in a cool place, well covered.
2. Defrost the freezer compartment prior to cleaning (see "Defrosting" sec­tion).
3. Switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker or fuse.
4. Clean the appliance and the interior accessories with a cloth and lukewarm
Page 36
36
What to do if ...
Correcting Malfunctions
A malfunction may be caused by only a minor fault that you can rectify yourself using the following instructions. Do not perform any other work on the appliance if the following information does not provide assistance in your specific case.
Warning! Repairs to refrigerators/freezers may only be performed by qualified service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact your specialist dealer or our Customer Service.
water. Commercially available dish washing detergents may also be used.
5. After cleaning wipe with fresh water and rub dry. Accumulation of dust at the condenser increases energy consumption. For
this reason carefully clean the condenser at the back of the appliance once a year with a soft brush or a vacuum cleaner.
6. Check the water drain hole on the rear wall of the fridge. Clear a blocked drain hole with the aid of the green peg.
7. After everything is dry place appliance back into service.
Energy Saving Tips
• Do not install the appliance near cookers, radiators or other sources of
warmth. High ambient temperatures cause longer, more frequent opera­tion of the compressor.
• Ensure sufficient air circulation and exhaust at the appliance base and
at the back wall of the appliance. Never cover air vent openings.
• Do not place warm foods into the appliance. Allow warm foods to cool
first.
• Only leave door open as long as necessary.
• Do not set temperature any colder than necessary.
then be used to cool the fridge.
• Keep the heat emitting condenser, the metall grille on the rear wall of
your appliance, always clean.
Page 37
37
The food is too warm.
The appliance is near a heat source.
Temperature is not properly adjusted.
Please look in the "Initial Start Up" section.
Turn the temperature regula­tor to a colder setting tempo­rarily.
Door was open for an exten­ded period.
Please look in the "Installation location" section.
A large quantity of warm food was placed in the appliance within the last 24 hours.
Open the door only as long as necessary.
Malfunction Possible Cause Remedy
Appliance does not work.
Appliance is not switched on Switch on the appliance. Mains plug is not plugged in
or is loose.
Insert mains plug.
Fuse has blown or is defective. Check fuse, replace if necessary.
Socket is defective.
Mains malfunctions are to be corrected by an electrician.
Appliance cools too much. Temperature is set too cold.
Turn the temperature regula­tor to a warmer setting tem­porarily.
Heavy build up of frost, possi­bly also on the door seal.
Door seal is not air tight (pos­sibly after changing over the hinges).
Carefully warm the leaking sections of the door seal with a hair dryer (not hotter than approx. 50 °C). At the same time shape the warmed door seal by hand such that it sits correctly.
Interior lighting does not work.
Light bulb is defective.
Please look in the "Changing the Light Bulb" section.
Unusual noises.
The appliance is touching the wall or other objects.
Appliance is not level.
A component, e.g. a pipe, on the rear of the appliance is touching another part of the appliance or the wall.
If necessary, carefully bend the component out of the way.
Move the appliance slightly.
Readjust the feet.
The compressor starts after a period of time.
See the "Cleaning and Care" section.
This is normal, no error has occurred.
The compressor does not start immediately after changing the temperature setting. Water on the floor or on storage shelves.
Water drain hole is blocked.
Page 38
38
Changing the light bulb
Warning! There is a risk of electric shocks! Before changing the light bulb, switch off the appliance and unplug it, or pull the fuse or the circuit breaker.
Light bulb data: 220-240 V, max. 15 W
1. To switch off the appliance, turn the temperature regulator to position "0".
2. Unplug the mains plug.
3. To change the light bulb, unscrew the light cover.
4. Unhook the light bulb cover as shown.
5. Change the defective light bulb.
6. Refit the light bulb cover and the screw.
7. Put the refrigerator back into opera­tion.
D411
Page 39
39
Customer Service
If you cannot find the remedy for a malfunction in these operating instruc­tions, please contact your dealer or our customer service department.
Selective ordering of replacement parts can save unnecessary travel and costs. For this reason always provide the following appliance information:
This information can be found on the serial plate in the interior at the left of the appliance.
• Model Name
• Model Number (PNC)
• Serial Number (S-No.)
We recommend that you enter this information here, so that it is handy if needed.
Note: The customer bears the costs of unjustified customer service calls even during the guarantee period.
Regulations, Standards, Guidelines
This appliance was designed for household use and was manufactured in accordance with the appropriate standards. The necessary measures in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and the regu­lations of the German Society of Electrical Engineers (VDE) were observed in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks. This appliance is in accordance with the following EU guidelines: – 73/23/EWG dated 19 February 1973 - low voltage guidelines. – 89/336/EWG dated 3 May 1989 (including guideline change notice 92/31/EWG) - EMV guideline
Page 40
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG Änderungen vorbehalten 2223 379-23---12/07 Subject to change without notice
Loading...