Page 1
user manual
Dishwasher
GA60LXI101
Page 2
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information ................................... 2
Product description ................................ 3
Control panel .......................................... 3
First use ................................................. 5
Set the water softener ............................ 5
Use of dishwasher salt ............................ 6
Use of rinse aid ....................................... 7
Daily use ................................................. 8
Load cutlery and dishes .......................... 9
Use of detergent ................................... 11
Multi-tab function .................................. 12
Subject to change without notice
Select and start a washing programme 13
Unloading the dishwasher .................... 14
Washing programmes .......................... 14
Care and cleaning ................................ 15
What to do if… ..................................... 16
Technical data ...................................... 18
Hints for test institutes .......................... 18
Installation ............................................ 19
Water connection ................................. 20
Electrical connection ............................. 22
Environment concerns .......................... 22
Safety information
In the interest of your safety and to ensure the correct use, before installing
and first using the appliance, read this
user manual carefully, including its hints
and warnings. To avoid unnecessary
mistakes and accidents, it is important
to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these
instructions and make sure that they remain with the appliance if it is moved or
sold, so that everyone using it through
its life will be properly informed on appliance use and safety.
Correct use
• This dishwasher is only intended for washing household utensils suitable for machine washing.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Only use products (detergent, salt and
rinse aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance is in operation, hot steam may escape.
• Do not take any dishes out of the dishwasher before the end of the washing cycle.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• This product should be serviced only by an
authorized service engineer, and only genuine spare parts should be used.
• Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons
could cause injury or serious malfunctioning. Contact your local Service Force Centre. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause chemical burns to eyes, mouth and throat. Could
endanger life! Comply with the safety instructions of the dishwasher detergent
manufacturer.
• The water in your dishwasher is not for
drinking. Detergent residues may still be
present in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded
or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.
• Do not sit or stand on the open door.
Page 3
electrolux 3
Child safety
• This appliance is designed to be operated
by adults. Do not allow children to use the
dishwasher unsupervised.
• Keep all packaging well away from children. There is a risk of suffocation.
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the dishwasher when the door is open.
Installation
• Check your dishwasher for any transport
damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.
• All packaging must be removed before
use.
• Any electrical and plumbing work required
to install this appliance must be carried out
by a qualified and competent person.
Product description
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged; or if the control panel, work top or
plinth area are damaged such that the inside of the appliance is freely accessible.
Contact your local Service Force centre, in
order to avoid hazard.
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
Warning! For electrical and water
connection carefully follow the
instructions given in the specific
paragraphs.
1 Upper basket
2 Water hardness dial
3 Salt container
4 Detergent dispenser
5 Rinse aid dispenser
6 Rating plate
7 Filters
8 Lower spray arm
9 Upper spray arm
Page 4
4 electrolux
Control panel
4
1 Programme selection buttons
2 Indicator lights
3 On/Off button
4 Function buttons
Indicator lights
Wash Comes on when the washing and rinsing phases
Dry Comes on when the drying phase is running.
are running.
End Comes on when a washing programme has
Rinse aid
1)
Salt
1)
1) The salt and rinse aid indicator lights never come on while a washing programme is running even if
filling with salt and/or rinse aid is necessary.
Function buttons
The following functions can be set using
ended. It also has added functions of visual signalling as:
– the setting of the water softener,
– intervention of an alarm due to the malfunction
of the machine.
Comes on when the rinse aid has run out.
Comes on when the special salt has run out.
• setting the water softener level,
• cancelling a washing programme,
these buttons:
Page 5
electrolux 5
• activation/deactivation of the Multitab
function,
• activation/deactivation of the rinse aid dis-
penser when Multitab function is active.
Setting mode
Press the On/Off button; if ALL programme
button lights come on the appliance is in setting mode.
Always remember that when performing
the following operations:
– selecting a washing programme,
Press the On/Off button; if a programme button light is on the last performed or selected
programme is still set. In this case, to return
to setting mode, the programme has to be
cancelled.
To cancel a set programme or a
programme in progress
Simultaneously press and hold the two function buttons B and C until all the programme
button lights come on. The programme has
been cancelled and the machine is now in
setting mode.
– setting the water softener level,
– activating/deactivating the rinse aid,
the appliance MUST be in setting mode.
First use
Before using your dishwasher for the first
time:
• Ensure that the electrical and water con-
nections comply with the installation instructions
• Remove all packaging from inside the ap-
pliance
• Set the water softener level
• Pour 1 litre of water into the salt container
and then fill with dishwasher salt
• Fill the rinse aid dispenser
If you want to use combi detergent
tablets such as: ''3 in 1'', ''4 in 1'', ''5
in 1'' etc... set the Multitab function.
(See ''Multitab function'').
Set the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and
salts from the water supply, which would
have a detrimental or adverse effect on the
operation of the appliance.
The higher the content of these minerals and
salts, the harder your water is. Water hardness is measured in equivalent scales, German degrees (dH°), French degrees (°TH)
and mmol/l (millimol per litre - international
unit for the hardness of water).
Water hardness Adjusting the water hardness setting Use of
°dH °TH mmol/l manually electronically
51 - 70 91 - 125 9,1 - 12,5 2 level 10 yes
43 - 50 76 - 90 7,6 - 9,0 2 level 9 yes
37 - 42 65 - 75 6,5 - 7,5 2 level 8 yes
29 - 36 51 - 64 5,1 - 6,4 2 level 7 yes
23 - 28 40 - 50 4,0 - 5,0 2 level 6 yes
19 - 22 33 - 39 3,3 - 3,9 2 level 5 yes
15 - 18 26 - 32 2,6 - 3,2 1 level 4 yes
11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes
4 - 10 7 - 18 0,7 - 1,8 1 level 2 yes
The softener should be adjusted according
to the hardness of the water in your area.
Your local Water Authority can advise you on
the hardness of the water in your area.
The water softener must be set in two
ways: manually, using the water hardness dial and electronically.
salt
Page 6
6 electrolux
Water hardness Adjusting the water hardness setting Use of
°dH °TH mmol/l manually electronically
< 4 < 7 < 0,7 1 level 1 no
Setting manually
The dishwasher is factory set at position
2.
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness dial to position
1 or 2 (see chart).
4. Replace the lower basket.
3. Press function button A, the lights of
function buttons B and C go off while the
light of function button A continues to
flash, at the same the End indicator light
starts to flash.
The current level is indicated by the number of flashes of the End indicator light.
Examples:
5 flashes, pause, 5 flashes, pause, etc. =
level 5
6 flashes, pause, 6 flashes, pause, etc. =
level 6
4. To change the level, press function button A. Each time the button is pressed
the level changes. (For the selection of the
new level see the chart).
Examples: If the current level is 5, by
pressing function button A once, level 6
is selected. if the current level is 10, by
pressing function button A once, level 1
Setting electronically
The dishwasher is factory set at level 5.
is selected.
5. To memorize the operation, switch off the
dishwasher by pressing the On/Off button.
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Simultaneously press and hold function
buttons B and C, until the lights of function buttons A, B and C start flashing.
salt
Use of dishwasher salt
Warning!
Only use salt specifically designed for use in
dishwashers. All other types of salt not specifically designed for use in a dishwasher,
especially table salt, will damage the water
softener. Only fill with salt just before starting
one of the complete washing programmes.
This will prevent any grains of salt or salty
water, which may have been spilt, remaining
on the bottom of the machine for any period
of time, which may cause corrosion.
To fill:
1. Open the door, remove the lower basket
and unscrew the cap of the salt container
by turning it anticlockwise.
2. Pour 1 litre of water into the container
(this is necessary only before filling
with salt for the first time) .
3. Using the funnel provided, pour in the salt
until the container is full.
Page 7
4. Replace the cap making sure that there
is no trace of salt on the screw thread or
on the gasket.
Use of rinse aid
Warning! Only use branded rinse aid for
dishwashers.
Never fill the rinse aid dispenser with any
other substances (e.g. dishwasher
cleaning agent, liquid detergent). This
would damage the appliance.
Rinse aid ensures thorough rinsing, and
spot and streak free drying.
Rinse aid is automatically added during
the last rinse.
1. Open the container by pressing the release button (A).
electrolux 7
5. Replace the cap tightly turning it clockwise until it stops with a click.
Do not worry if water overflows from the
unit when filling with salt, this is quite
normal.
The salt indicator light on the control
panel can remain illuminated for 2-6
hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using
salt that takes longer to dissolve
then this can take longer. The operation of the machine is not affected.
2. Add the rinse aid in the container. The
maximum level for filling is indicated by
"max".
The dispenser holds about 110 ml of rinse
aid, which is sufficient for between 16 and
40 washing cycles, depending upon the
dosage setting.
3. Ensure that the lid is closed after every
refill.
Clean up any rinse aid spilt during filling
with an absorbent cloth to avoid excess
foaming during the next wash.
According to the finish and drying results obtained, adjust the dose of rinse aid by means
of the 6 position selector (position 1 minimum
dosage, position 6 maximum dosage).
The dose is factory set in position 4.
Increase the dose if there are drops of water
or lime spots on the dishes after washing.
Page 8
8 electrolux
Reduce it if there are sticky whitish streaks
on the dishes or a bluish film on glassware or
knife blades.
Daily use
• Check if it’s necessary to refill with dishwasher salt or rinse aid.
• Load cutlery and dishes into the dishwasher.
• Fill with dishwasher detergent.
• Select a wash programme suitable for the
cutlery and dishes.
• Start the wash programme.
Helpful hints and tips
Sponges, household cloths and any object
that can absorb water may not be washed in
the dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
• When loading the dishes and cutlery,
please note:
– Dishes and cutlery must not impede the
rotation of the spray arms.
For washing in the dishwasher the following cutlery and dishes
are not suitable: are of limited suitability:
• Cutlery with wooden, horn, china or mother-ofpearls handles.
• Plastic items that are not heat resistant.
• Older cutlery with glued parts that are not temperature resistant.
• Bonded cutlery items or dishes.
• Pewter or copper items.
• Lead crystal glass.
• Steel items prone to rusting.
• Wooden platters.
• Items made from synthetics fibres.
– Load hollow items such as cups,
glasses, pans, etc. with the opening
downwards so that water cannot collect
in the container or a deep base.
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick coatings have a tendency to retain water
drops; these items will not dry as well as
porcelain and steel items.
• Light items (plastic bowls etc.) must be
loaded in the upper basket and arranged
so they do not move.
• Only wash stoneware in the dishwasher if it is
specially marked as being dishwasher-safe by
the manufacturer.
• Glazed patterns may fade if machine washed
frequently.
• Silver and aluminium parts have a tendency to
discolour during washing: Residues, e.g. egg
white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if
it is not to be washed straight after use.
Page 9
Load cutlery and dishes
The lower basket
The lower basket is designed to take saucepan, lids, plates, salad bowls, cutlery etc.
Service dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely.
electrolux 9
The cutlery basket
Long bladed knives stored in an upright
position are a potential hazard. Long
and/or sharp items of cutlery such as
carving knives must be positioned horizontally in the upper basket. Take care
when loading or unloading sharp items
such as knives.
Forks and spoons should be placed in the
removable cutlery basket with the handles
facing downwards and the knives with their
handles facing upwards.
The rows of prongs in the lower basket can
lie flat to allow you to load pots, pans and
bowls.
If the handles protrude from the bottom of the
basket, obstructing the lower spray arm, load
the cutlery with the handles facing upwards.
Mix spoons with other cutlery to prevent
them from sticking together.
To make loading of the cutlery basket easier,
lower the cutlery basket handle.
Page 10
10 electrolux
For best results we recommend that you use
the cutlery grids.
If the size and dimensions of the cutlery do
not allow the use of the grids, they can be
easily hidden.
The cutlery basket is in two parts which can
be separated to give greater loading flexibility. To separate the two parts, slide them
horizontally in opposite directions and pull
them apart.
Glasses with long stems can be placed upside down in the cup racks.
The cup racks can be adjusted in three different positions to improve loading flexibility.
To reassemble, reverse the procedure.
The upper basket
The upper basket is designed for saucers,
salad bowls, cups, glasses, pots and lids.
Arrange items on and underneath the cup
racks so that water can reach all surfaces.
Page 11
electrolux 11
For glasses with long stems (according to the
size and dimensions), set the glass holder to
the left or right position.
The central rows of prongs can be easily lowered to improve loading flexibility.
Before closing the door, ensured that
the spray arms can rotate freely.
Adjusting the height of the upper basket
If washing very large plates you can load
them in the lower basket after moving the
upper basket to the higher position.
Maximum height of the dishes in the lower
With upper basket
raised
With upper basket
lowered
basket
33 cm
29 cm
To move to the higher position proceed
as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is
stable.
To lower the basket to the original position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then
allow the mechanism to drop back down
slowly, keeping hold of it.
Never lift or lower the basket on one side
only
With the upper basket raised we recommend you adjust the cup racks in the
lowest position.
After loading your machine always
close the door, as an open door can
be a hazard.
Use of detergent
Only use detergents specifically designed for use in dishwashers.
Please observe the manufacturer’s dosing and storage recommendations as
stated on the detergent packaging.
Using no more than the correct amount
of detergent contributes to reducing pollution.
Fill with detergent
1. Open the lid.
Page 12
12 electrolux
2. Fill the detergent dispenser (1) with detergent. The marking indicates the dosing
levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent.
3. All programmes with prewash need an
additional detergent dose (5/10 g) that
must be placed in the prewash detergent
chamber (2).
This detergent will be used during the
prewash phase.
When using detergent tablets; place the
tablet in compartment (1)
1
2
Multi-tab function
This appliance is equipped with the "Multitab
function", that allows the use of the "Multitab"
combi detergent tablets.
These products are detergents with a combined cleaning, rinsing and salt functions.
They can also contain other different agents
depending on which kind of tablets you
choose ("3 in 1", "4 in 1", "5 in 1" etc...).
Check whether these detergents are suitable
for your water hardness. See the manufacturers instructions.
Once this function is selected it will remain
active for all following wash programmes.
With the selection of this function the inflow
of rinse aid and salt from each respective
supply container is automatically deactivated
4. Close the lid and press until it locks in
place.
Detergent tablets from different manufacturers dissolve at different rates. For
this reason, some detergent tablets do
not attain their full cleaning power during
short washing programmes. Therefore,
please use long washing programmes
when using detergent tablets, to ensure
the complete removal of detergent residuals.
and also the indicator lights for salt and rinse
aid are deactivated.
When using the "Multitab function", the cycle
durations may change.
Activate/deactivate the ''Multitab function'' before the start of a washing programme.
Once the programme is running, the
"Multitab function " can NO longer be
changed. If you want to cancel the "Multitab function " you have to cancel the
programme setting and then deactivate
the ''Multitab function''. In this case you
have to set a washing programme (and
desired options) again.
Page 13
Activation/deactivation of the Multitab
function
Simultaneously press and hold the two Multitab buttons (function buttons D and E) until
the Multitab indicator light comes on. This
means that the function is active.
To deactivate the function press the same
buttons again until the indicator light corresponding to the Multitab function symbol
goes off.
If the drying results are not satisfactory we suggest that you:
1. Fill up the rinse aid dispenser with
rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position
2.
• The activation/deactivation of the
rinse aid is only possible with the Multitab function active.
Activation/deactivation of the rinse aid
dispenser
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Simultaneously press and hold function
buttons B and C, until the lights of function buttons A , B, and C start flashing.
electrolux 13
3.
Press function button B, the lights of
function buttons A and C go off while the
light of function button B continues to
flash.
4. To activate the rinse aid dispenser, press
button B again, the End indicator light
comes on, indicating that the rinse aid
dispenser has been activated.
5. To memorize the operation, switch off the
dishwasher by pressing the On/Off button.
6. To deactivate the rinse aid dispenser
again, follow the above instructions until
the End indicator light goes off.
If you decide to revert back to the
use of individual detergents we advise that you:
1. Deactivate the Multi-tab function.
2. Fill up the salt container and the rinse
aid dispenser again.
3. Adjust the water hardness setting to
the highest setting and perform 1
normal washing programme without
loading any dishes.
4. Adjust the water hardness setting
according to the hardness of the water in your area.
5. Adjust the rinse aid dosage.
Select and start a washing programme
Select the washing programme with
the door slightly opened. The start of
the programme will occur only after
the closure of the door. Until then it
is possible to modify the settings
1. Check that the baskets have been loaded
correctly and that the spray arms are free
to rotate.
2. Check that the water tap is opened.
3. Press the On/Off button. The dishwasher
must be in setting mode.
4. Press the button corresponding to the required programme (see ''Washing programmes'' chart).
When a programme has been selected
the corresponding light comes on.
The phase indicator lights foreseen for
the set programme start flashing.
Close the dishwasher door, the programme starts automatically.
Once the programme starts, the phase
indicator lights go off except for the indi-
cator light of the phase in progress which
will remain on with a static light.
The selection of the washing programme can also occur with the door
closed. Keep in mind that in this way,
once a washing programme button is
pressed, you have ONLY 3 seconds in
which you can choose another programme after which the selected programme will start automatically.
Warning! Interrupt or cancel a
washing programme in progress
ONLY if it's absolutely necessary.
Attention! Hot steam may escape
when the door is opened. Open the
door carefully.
Page 14
14 electrolux
Interrupt a washing programme in
progress
• Open the dishwasher door; the pro-
gramme will stop. Close the door; the programme will start from the point at which
it was interrupted.
• Press the On/Off, all lights will turn off.
Press the On/Off button again; the programme will start from the point at which
it was interrupted.
Cancel a washing programme in
progress
• Simultaneously press and hold the two
function buttons B and C until all the pro-
• If a new washing programme is to be selected, check that there is detergent in the
detergent dispenser.
End of the washing programme
• The dishwasher will automatically stop.
•The End indicator light will come on.
• The light of the programme just ended will
remain on.
1. Switch off the dishwasher by pressing the
On/Off button.
2. Open the dishwasher door, leave it ajar
and wait a few minutes before removing
the dishes; this way they will be cooler
and the drying will be improved.
gramme lights come on.
Unloading the dishwasher
• Hot dishes are sensitive to knocks. The
dishes should therefore be allowed to cool
down before removing from the appliance.
•Empty the lower basket first and then the
upper one; this will avoid water dripping
from the upper basket onto the dishes in
the lower one.
• Water may appear on the sides and the
door of the dishwasher as the stainless
steel will eventually become cooler than
the dishes.
When the washing programme has
finished, it is recommended that the
dishwasher is unplugged and the
water tap turned off.
Washing programmes
Programme Degree of soil Type of load Programme description
Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
Main wash
Final rinse
Main wash
1 intermediate rinse
Final rinse
Drying
Intensive Heavy soil
Normal Normal soil
1)
ECO
2)
Quick
Glass Normal soil
Normal soil
Normal or light
soil
Crockery, cut-
lery, pots and
pans
Crockery, cut-
lery, pots and
pans
Crockery and
cutlery
Crockery and
cutlery
Delicate crockery
and glassware
Page 15
electrolux 15
Programme Degree of soil Type of load Programme description
Any Partial load (to be
Prewash
1) Test programme for test institutes
2) Ideal for washing a partially loaded dishwasher. This is the perfect daily programme, made to meet
the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery.
Programme Programme duration
Intensive 130 - 140 1,4 - 1,6 16 - 18
Normal 90 - 100 1,4 - 1,6 18 - 20
1)
ECO
Quick 30 0,9 9
Glass 60 - 70 0,8 - 0,9 14 - 15
Prewash 12 0,1 4
1) Test programme for test institutes
(in minutes)
150 - 160 1,0 - 1,1 12 - 13
completed later
in the day).
Consumption values
1 cold rinse (to avoid food scraps from
sticking).
This programme does not require the use
of detergent.
Energy consumption
(in kWh)
Water consumption
(in litres)
The consumption values are intended as
a guide and depends on the pressure
and the temperature of the water and also by the variations of the power supply
and the amount of dishes.
Care and cleaning
Cleaning the filters
The filters must be checked and cleaned
from time to time. Dirty filters will degrade the
washing result.
Warning! Before cleaning the filters
ensure that the machine is switched off.
1. Open the door, remove the lower basket.
2. The dishwasher filter system comprises a
coarse filter (A), a microfilter (B) and a flat
filter. Unlock the filter system using the
handle on the microfilter.
3. Turn the handle about 1/4 a turn anticlockwise and remove the filter system
Page 16
16 electrolux
4. Take hold of the coarse filter (A) by the
handle with the hole and remove from the
microfilter (B).
5. Clean all filters thoroughly under running
water.
6. Remove the flat filter from the base of the
washing compartment and clean both
faces thoroughly.
7. Put the flat filter back in the base of the
washing compartment and ensure that it
fits perfectly.
8.
Place the coarse filter (A) in the microfilter
(B) and press together.
9. Put the filter combination in place and
lock by turning the handle clockwise to
the stop. During this process ensure that
the flat filter does not protrude above the
base of the washing compartment.
NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and will result in
damage to the appliance.
NEVER try to remove the spray
arms.
If residues of soil have clogged the holes
in the spray arms, remove the debris
with a cocktail stick.
External cleaning
Clean the external surfaces of the machine
and control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc...).
Internal cleaning
Ensure that the seals around the door, the
detergent and rinse aid dispensers are
cleaned regularly with a damp cloth.
We recommend every 3 months you run the
wash programme for heavy soiled dishes using detergent but without dishes.
Prolonged periods of non-operation
If you are not using the machine for a prolonged period of time you are advised to:
1. Unplug the appliance and then turn off
the water.
2. Leave the door ajar to prevent the formation of any unpleasant smells.
3. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location
where the temperature is below 0°C. If this is
unavoidable, empty the machine, close the
appliance door, disconnect the water inlet
pipe and empty it.
Moving the machine
If you have to move the machine (moving
house etc...):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge
hoses.
4. Pull the machine out together with the
hoses.
Avoid over tilting the machine during transportation.
What to do if…
The dishwasher will not start or stops during
operation.
Certain problems can be due to the lack of
simple maintenance or oversights, which can
be solved with the help of the hints described
in the chart, without calling out an engineer.
Page 17
Switch off the dishwasher, open the door
and carry out the following suggested corrective actions.
Fault codes and malfunction Possible cause and solution
• continuous flashing of the light of the running
programme
• 1 flash of the End indicator light
The dishwasher does not fill with water
• continuous flashing of the light of the running
programme
• 2 flashes of the End indicator light
The dishwasher will not drain
• continuous flashing of the light of the running
programme
• 3 flashes of the End indicator light
Anti-flood device is activated
Malfunction Possible cause and solution
The programme does not start
Once these checks have been carried out
switch on the appliance.
The programme will continue from the point
at which it was interrupted.
If the malfunction or fault code reappears
contact your local Service Force Centre.
For other fault codes not described in the
above chart, please contact your local Service Force Centre.
Contact your local Service Force Centre,
quoting the model (Mod.), product number
(PNC) and serial number (S.N.).
electrolux 17
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is turned off.
Turn the water tap on.
• The filter (where present) in the water inlet hose
is blocked.
Clean the filter.
• The water inlet hose has not been correctly laid
or it is kinked or squashed.
Check the water inlet hose connection.
• The sink spigot is blocked.
Clean out the sink spigot.
• The water drain hose has not been correctly laid
or it is kinked or squashed.
Check the water drain hose connection.
• Close the water tap and contact your local
Service Force Centre.
• The dishwasher door has not been properly
closed.
Close the door.
• The main plug is not plugged in.
Insert the main plug
• The fuse has blown out in the household fuse
box.
Replace the fuse.
This information can be found on the rating
plate located on the side of the dishwasher
door.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 18
18 electrolux
The wash results are not satisfactory
The dishes are not
clean
The dishes are wet
and dull
There are streaks,
milky spots or a bluish coating on
glasses and dishes
Water drops have
dried onto glasses
and dishes
• The wrong programme has been selected.
• The dishes are arranged in such a way as to stop water reaching all parts
of a surface. The baskets must not be overloaded.
• The spray arms do not rotate freely due to incorrect arrangement of the
load.
• The filters in the base of the washing compartment are dirty or incorrectly
positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes; the salt container is
empty or incorrect level of the water softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
• Rinse aid was not used.
• The rinse aid dispenser is empty.
• Decrease rinse aid dosage.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer consumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre.
Technical data
Dimensions Width
Electrical connection - Voltage Overall power - Fuse
Water supply pressure Minimum
Capacity 12 place settings
Height
Depth
Information on the electrical connection is given on the rating plate
on the inner edge of the dishwasher door.
0,05 MPa (0,5 bar)
Maximum
59,6 cm
86,8 - 94,8 cm
57,5 cm
0,8 MPa (8 bar)
Hints for test institutes
Testing in accordance with EN 60704 must
be carried out with appliance fully loaded and
using the test programme (see "Consumption values").
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
Full load: 12 standard place settings
Amount of detergent required: 5 g + 25 g (Type B)
Rinse aid setting position 4 (Type III)
aid dispenser have been filled with salt and
rinse aid respectively and using the test programme (see "Consumption values").
Page 19
electrolux 19
Arrangement upper basket (take off the
glass holder)
Cup racks: position 2
Arrangement lower basket
Arrangement cutlery basket
Installation
Warning! Any electrical and/or
plumbing work required to install
this appliance should be carried out
by a qualified electrician and/or
plumber or competent person.
Remove all packaging before positioning the
machine.
If possible, position the machine next to a
water tap and a drain.
This dishwasher is designed to be fitted under a kitchen counter or work surface.
Attention! Carefully follow the instructions
on the enclosed template for building in the
dishwasher and fitting the furniture panel.
No further openings for the venting of the
dishwasher are required, but only to let the
water fill and drain hose and power supply
cable pass through.
The dishwasher incorporates adjustable feet
to allow the adjustment of the height.
Page 20
20 electrolux
During all operations that involve accessibility
to internal components the dishwasher has
to be unplugged.
When inserting the machine, ensure that the
water inlet hose, the drain hose and the supply cable are not kinked or squashed.
Fixing to the adjacent units
The dishwasher must be secured against tilting.
Therefore make sure that the counter it is
fixed under, is suitably secured to a fixed
Water connection
Water inlet connection
This appliance can be connected to either a
hot (max. 60°) or cold water supply.
With a hot water supply you can have a significant reduction of energy consumption.
This however, depends on how the hot water
is produced. (We suggest alternative sources
of energy that are more environmentally
friendly as e.g. solar or photovoltaic panels
and aeolian).
For making the connection itself, the coupling nut fitted to the appliance water inlet
hose is designed to screw onto a 3/4" thread
spout or to a purpose made quick-coupling
tap such as the Press-block.
The water pressure must be within the limits
given in the 'Technical data'. Your local Water Authority will advise you on the average
mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being connected.
The appliance features inlet and drain hoses
which can be turned either to the left or the
right to suit the installation by means of the
locknut. The locknut must be correctly
fitted to avoid water leaks.
Attention! NOT all dishwasher models of
have inlet and drain hoses provided with
a locknut. In this case, this facility is not
available.
If the appliance is connected to new pipes or
pipes which have not been used for a long
time, you should run the water for a few minutes before connecting the inlet hose.
DO NOT use connection hoses which
have previously been used on an old appliance.
structure (adjacent kitchen units cabinets,
wall).
Levelling
Good levelling is essential for correct closure
and sealing of the door.
When the appliance is correctly levelled, the
door will not catch on either side of the cabinet .
If the door does not close correctly, loosen
or tighten the adjustable feet until the machine is perfectly level.
This appliance has been fitted with safety features which will prevent the water
used in the appliance from returning
back into the drinking water system. This
appliance complies with the applicable
plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water inlet hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running
water.
Please take care when installing the water
inlet hose:
• The electrical cable for the safety valve is
in the double-walled water inlet hose. Do
not immerse the water inlet hose or the
safety valve in water.
• If water inlet hose or the safety valve is
damaged, remove the mains plug immediately.
• A water inlet hose with safety valve must
only be replaced by the Service Force
Centre.
Warning! Dangerous voltage
Page 21
electrolux 21
Water drain connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink running into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
The waste connection must be at a height of
between 30 cm (minimum) and 100 cm
(maximum) from the bottom of the dishwasher.
The drain hose can face either to the right or
left of the dishwasher
Ensure the drain hose is not bent or squashed as this could prevent or slow down the
discharge of water.
The sink plug must not be in place when the
machine is draining as this could cause the
water to syphon back into the machine.
If you use a drain hose extension it must be
no longer than 2 metres and its internal di-
ameter must be no smaller than the diameter
of the hose provided.
Likewise the internal diameter of the couplings used for connections to the waste
outlet must be no smaller than the diameter
of the hose provided.
When connecting the drain hose to an under
sink trap spigot, the entire plastic mem-
brane (A) must be removed. Failure to remove all the membrane will result in food
particles building up over time eventually
blocking the dishwasher drain hose spigot
Our appliances are supplied with a security device to protect against the return of dirty water back into the machine.
If the spigot of your sink has a "no return
valve" incorporated this can prevent the
correct draining of your dishwasher. We
therefore advise you to remove it.
To avoid water leakage after installation
make sure that the water couplings are
tight.
Page 22
22 electrolux
Electrical connection
Warning! Safety standards require
the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated voltage and type of supply on the rating
plate match that of the supply where
the appliance is to be installed. The
fuse rat ing is also to be foun d on the
rating plate.
Always plug the mains plug into a
correctly installed shockproof socket.
Multi-way plugs, connectors and extension cables must not be used.
This could constitute a fire hazard
through overheating.
Environment concerns
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
If necessary, have the domestic wiring system socket replaced. In case
that the electrical cable has to be
replaced, contact your local Service
Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by pulling on the cable. Always pull the
plug.
The manufacturer accepts no liability for failure to observe the above
safety precautions.
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate container at the community waste disposal facilities.
Warning! When a unit is no longer being
used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose
of them.
• Dispose of the door catch. This prevents children from trapping themselves inside and endangering their
lives.
Page 23
electrolux 23
Page 24
www.electrolux.com
www.electrolux.ch
117972860 - 00 - 022008
Loading...