AEG-Electrolux GA552F101 User Manual

Download

user manual

GA552F101

dishwasher

We were thinking of you

when we made this product

welcome to the world of Electrolux electrolux 3

You’ve chosen a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You can look at some examples on the cover in this manual. But now it’s time to study this manual and start using and enjoying the benefits from your new machine. We promise that it’ll make your life a little easier. Good luck!

Welcome to the world of Electrolux

117987 91/0

Safety information 5 Product description 7 Control panel 8 First use 11 Daily use 15 Washing programmes 28 Care and cleaning 29 Something not working 32 Technical data 35 Hints for test institutes 37 Installation 39 Environment concerns 43 Warranty/Point of Service 44

Contents

The following symbols are used in this manual:

Important information concerning your personal safety and information on how to avoid damaging the appliance.

General information and tips

Environmental information

4 electrolux contents

safety information electrolux 5

In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.

Correct use

● This dishwasher is only intended

for washing household utensils suitable for machine washing.

● Do not put any solvents in the

dishwasher. This could cause an explosion.

● Knives and other items with sharp

points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket.

● Only use products (detergent, salt

and rinse aid) suitable for dishwashers.

● Avoid opening the door whilst the

appliance is in operation, hot steam may escape.

● Do not take any dishes out of the

dishwasher before the end of the dishwashing cycle.

Safety information

● After use, isolate the appliance

from the power supply and turn off the water supply.

● This product should be serviced

only by an authorised service engineer, and only genuine spare parts should be used.

● Under no circumstances should

you attempt to repair the machine yourself. Repairs carried out by inexperienced persons will cause injury or serious malfunctioning. Contact your local Service Force Centre. Always insist on genuine spare parts.

General safety

● Dishwasher detergents can cause

chemical burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer.

● The water in your dishwasher is

not for drinking. Detergent residues may still be present in your machine.

● Ensure that the door of the

dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.

● Do not sit or stand on the open

door.

Child safety

● This appliance is designed to be

operated by adults. Don’t allow children to use the dishwasher unsupervised.

6 electrolux safety information

For electrical and water connection carefully follow the instructions given in specific paragraphs.

● Keep all packaging well away from

children. There is risk of suffocation.

● Keep all detergents in a safe place

out of children’s reach.

● Keep children well away from the

dishwasher when the door is open.

Installation

● Check your dishwasher for any

transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.

● All packaging must be removed

before use.

● Any electrical and plumbing work

required to install this appliance must be carried out by a qualified and competent person.

● For safety reasons it is dangerous

to alter the specifications or attempt to modify this product in any way.

● Never use the dishwasher if the

electrical supply cable and water hoses are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Contact your local Service Force centre, in order to avoid hazard.

● All sides of the dishwasher must

never be drilled to prevent damage to hydraulic and electric components.

product description electrolux 7

Product description

Ceiling spray arm Upper basket Upper basket spray arm Filters Lower spray arm Detergent dispenser Rinse aid dispenser Rating plate Salt container

1 2 3 4 5 6 7 8 9

8 9

8 electrolux control panel

Control panel

On/Off button Programme selection button Multi-tab button Half load button Indicator lights

1 2 3

4 5

Multi-tab button

This option allows the use of combi detergent tablets (“3 in 1”, “4 in 1”, “5 in 1” etc...). See “Multi-tab function”.

Half load button

This option is useful and economical when baskets are not fully loaded. It reduces the consumption of water and energy.

Remember to load both baskets. When using this option we

recommend to reduce the dose of detergent that is normally used for a complete load.

This option is available only with “Intensive” and “Normal ECO” washing programmes.

control panel electrolux 9

The salt and rinse aid indicator lights are never illuminated while a washing programme is running even if filling with salt and/or rinse aid is necessary.

End of programme

● Light on when the appliance is in setting

mode, light off when a washing programme is selected or in progress.

● Illuminates when a washing programme has

ended.

● It also has added functions of visual

signalling as:

- the setting of the water softener,

- activation/deactivation of the rinse aid dispenser,

- intervention of an alarm due to the malfunction of the machine.

Wash

Indicator lights

Dry

Illuminates when the washing and rinsing phases are running.

Illuminates when the drying phase is running.

Salt

Illuminates when the special salt has run out.

Rinse aid

Illuminates when the rinse aid has run out.

10 electrolux control panel

Setting mode

● Press On/Off button, programme

selection button light and end of programme light are illuminated =

appliance in setting mode.

● Press On/Off button, a washing

programme light is illuminated = last performed or selected programme still set. In this case, to return to setting mode, the programme has to be cancelled.

To cancel a set programme or a programme in progress

Simultaneously press and hold the two buttons positioned over the letter C, until the washing programme light turns off and the programme selection button light and end of programme light are illuminated.

The programme has been cancelled and the machine is now in setting mode.

Always remember that when:

- setting a washing programme,

- setting the water softener,

- activating/deactivating the rinse aid dispenser,

the appliance MUST be in setting mode.

first use electrolux 11

Before using your dishwasher for the first time:

● Ensure that the electrical and

water connections comply with the installation instructions

● Remove all packaging from inside

the appliance

● Set the water softener

● Pour 1 litre of water inside the salt

container and then fill with dishwasher salt

● Fill the rinse aid dispenser

If you want to use combi detergent tablets such as: “3 in 1”, “4 in 1”, “5 in 1” etc... set the Multi-tab function (see Multi-tab function).

First use

Set the water softener

The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.

The higher the content of these minerals and salts, the harder your water is.

Water hardness is measured in equivalent scales, German degrees (°dH), French degrees (°TH) and mmol/l (millimol per litre - international unit for the hardness of water).

The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.

no salt is necessary

Water hardness

°dH °TH mmol/l

Adjusting the

water

hardness

setting

Number of

flashes of the

“end of

programme”

indicator light

Use of

salt

51 - 70 91 - 125 9.0 - 12.5 level 10 10

9 8

7 6 5 4 3 2 1

yes

43 - 50 76 - 90 7.6 - 8.9

level 9

yes

37 - 42 65 - 75 6.5 - 7.5

level 8

yes

29 - 36 51 - 64 5.1 - 6.4

level 7

yes

23 - 28 40 - 50 4.0 - 5.0 level 6 yes 19 - 22 33 - 39 3.3 - 3.9

level 5

yes

15 - 18 26 - 32 2.6 - 3.2

level 4

yes

11 - 14 19 - 25 1.9 - 2.5 level 3 yes

4 - 10 7 - 18 0.7 - 1.8

level 2

yes

< 4 < 7 < 0.7

level 1

12 electrolux first use

The dishwasher is factory set at level 5.

1. Press the On/Off button. The

dishwasher must be in setting mode.

2. Press simultaneously and keep

pressed buttons 2 and 3, until the lights of buttons 1, 2 and 3 start flashing.

3. Press button 1, the lights of

buttons 2 and 3 turn off while the light of the button 1 goes on flashing, at the same time the end of programme indicator light starts to flash.

The current level is indicated by the number of flashes of the end

of programme indicator light. Examples:

5 flashes, pause, 5 flashes, pause, etc... = level 5

6 flashes, pause, 6 flashes, pause, etc... = level 6

4. To change the level, press button

1. Each time the button is pressed the level changes. (For the selection of the new level see the chart).

Examples:

if the current level is 5, by pressing button 1 once, level 6 is selected.

if the current level is 10, by pressing button 1 once, level 1 is selected.

5. To memorise the operation, switch off the dishwasher by pressing the On/Off button.

first use electrolux 13

Filling with dishwasher salt

Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion.

4. Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket.

5. Replace the cap tightly turning it clockwise.

To fill:

1. Open the door, remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise.

2. Pour 1 litre of water inside the container (this is necessary only

before filling with salt for the first time).

3. Pour in the salt until the container is full.

Do not worry if water overflows from the unit when filling with salt, this is quite normal.

The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. The function of the machine is not affected.

14 electrolux first use

Filling with rinse aid

Rinse aid ensures thorough rinsing, and spot and streak free drying.

Rinse aid is automatically added during the last rinse.

1. Open the container by pressing

the release button (A).

2. Add the rinse aid in the container.

The maximum level for filling is indicated by "max".

The dispenser holds about 110 ml of rinse aid, which is sufficient for between 16 and 40 dishwashing cycles, depending upon the dosage setting.

According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage).

The dose is factory set in position 4. Increase the dose if there are drops of

water or lime spots on the dishes after washing.

Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades.

3. Ensure that the lid is closed after every refill.

Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash.

Only use branded rinse aid for dishwashers.

Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.

daily use electrolux 15

● Check if it’s necessary to refill with

dishwasher salt or rinse aid

● Load cutlery and dishes into the

dishwasher.

● Fill with dishwasher detergent .

● Select a wash programme suitable

for the cutlery and dishes.

● Start the wash programme.

Loading cutlery and dishes

Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher.

● Before loading the dishes, you

should:

- Remove all left over food and debris.

- Soften remnants of burnt food in pans

● When loading the dishes and

cutlery, please note:

- Dishes and cutlery must not impede the rotation of the spray arms .

- Load hollow items such as cups, glasses, pans, etc. with the opening downwards so that water cannot collect in the container or a deep base.

- Dishes and items of cutlery must not lie inside one another, or cover each other.

- To avoid damage to glasses, they must not touch.

Daily use

- Lay small objects in the cutlery basket.

● Plastic items and pans with non

stick coatings have a tendency to retain water drops; these items will not dry as well as porcelain and steel items.

● Light items (plastic bowls etc.)

must be loaded in the upper basket and arranged so they do not move.

16 electrolux daily use

For washing in the dishwasher the following cutlery and dishes

are not suitable: - Cutlery with wooden, horn, china or mother-of-

pearls handles.

- Plastic items that are not heat resistant.

- Older cutlery with glued parts that are not temperature resistant.

- Bonded cutlery items or dishes.

- Pewter or copper items.

- Lead crystal glass.

- Steel items prone to rusting.

- Wooden platters.

- Items made from synthetics fibres.

are of limited suitability:

- Only wash stoneware in the dishwasher if it is specially marked as being dishwasher-safe by the manufacturer.

- Glazed patterns may fade if machine washed frequently.

- Silver and aluminium parts have a tendency to discolour during washing: Residues, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use.

daily use electrolux 17

The lower basket

The lower basket is designed to take saucepans, lids, plates, salad bowls, cutlery etc.

A serving plate can be placed in front of the cutlery basket.

The left plate rack can be folded down and the width can be adjusted.

● To fold them down, lift the two

plate racks slightly at the back and fold them onwards making them cross over one another.

● To set the width: pull the right-hand

plate rack upwards at the back until it disengages, then pull it towards the back out of the front guide.

Insert the plate rack in the other guide and press it down at the back until it snaps in.

The rear plate rack can be easily folded down to allow you to load pots, pans and bowls.

Folding down the right plate rack will create another plate rack that allows you to load deep plates and bowls.

1. Lift the two plate racks slightly at the back and fold them inward making them cross over one another.

18 electrolux daily use

To make loading of the cutlery basket easier, lower the cutlery basket handle (fig.2).

For best results we recommend you to use the cutlery grids.

If the size and dimensions of the cutlery do not allow the use of the grids, they can be easily hidden (fig. 3).

The cutlery basket

Long bladed knives stored in an upright position are a potential hazard.

Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket.

Take care when loading or unloading sharp items such as knives.

Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards (fig.1).

If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards.

Mix spoons with other cutlery to prevent them from sticking together.

fig. 1

fig. 2

fig. 3

daily use electrolux 19

The cutlery basket is in two parts which can be separated to give greater loading flexibility. To separate the two parts, slide them horizontally in opposite directions and pull them apart (fig. 4).

To reassemble, reverse the procedure.

fig. 4

20 electrolux daily use

The upper basket

The upper basket is designed for saucers, salad bowls, cups, glasses, pots and lids.

Adjustable cup racks

● Arrange items on and underneath

the cup racks so that water can reach all surfaces.

● The cup racks can be folded up

out of the way for tall crockery items.

● The cup racks can also be fixed in

an intermediate position. Lay or hang glasses with the stems in the slots in the cup racks.

Before closing the door, ensure that the spray arms can rotate freely.

Glass holders

For glasses with long stems and tall cylindrical glasses, fold up the glass holder. (Top picture)

To unload or when not needed, fold the glass holder back to the right. (Middle picture).

Glasses can also be placed over the bars pointing up. (Bottom picture).

daily use electrolux 21

Adjusting the height of the upper basket

If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position.

After loading your machine always close the door, as an open door can be a hazard.

The adjustment of the height of the upper basket is possible also when the basket has been loaded.

Moving the upper basket to the higher / lower position:

1. Pull out the basket completely.

2. Raise the upper basket as far as it will go and then lower it vertically. The upper basket will latch into the lower or higher position.

22 electrolux daily use

Maximum plate sizes with upper basket in higher position.

Maximum plate sizes with upper basket in lower position.

Arrangement of large plates in the lower basket

daily use electrolux 23

Use of detergent

Only use detergents specifically designed for use in dishwashers.

Please observe the manufacturer’s dosing and storage recommendations as stated on the detergent packaging.

Using no more than the correct amount of detergent contributes to reducing pollution.

Fill with detergent

1. Open the lid.

2. Fill the detergent dispenser (1) with detergent. The marking indicates the dosing levels:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent

3. All programmes with prewash need an additional detergent dose (5/10 g) that must be placed in the prewash detergent chamber (2). This detergent will take effect during the prewash phase.

When using detergent tablets; place the tablet in compartment (1)

4. Close the lid and press until it locks in place.

Detergent tablets

Detergent tablets from different manufactures dissolve at different rates. For this reason, some detergent tablets do not attain their full cleaning power during short washing programmes. Therefore, please use long washing programmes when using detergent tablets, to ensure the complete removal of detergent residuals.

24 electrolux daily use

Activation/deactivation of the Multitab function

Press the Multi-tab button, the corresponding indicator light illuminates. This means that the function is active.

To deactivate the function press the Multi-tab button again, the indicator light turns off.

Multi-tab function

This appliance is equipped with the Multi-tab function, that allows the use of combi detergent tablets.

These products are detergents with a combined cleaning, rinsing and salt functions. They can also contain other different agents depending on which kind of tablets you choose (“3 in 1”, “4 in 1”, “5 in 1” etc...)

Check whether these detergents are suitable for your water hardness. See the manufacturers instructions.

Once this function is selected it will remain active also for the following washing programmes.

With the selection of this function the inflow of rinse aid and salt from each respective supply container is automatically deactivated and also the indicator lights for salt and rinse aid are deactivated.

Select the Multi-tab function before the start of a washing programme.

With the use of the Multi-tab function, the cycle durations may change.

Once the programme is running, the Multi-tab function can NO longer be changed. If you want to exclude the Multi-tab function you have to cancel the programme setting and then deactivate the Multi-tab function. In this case you have to set a washing programme again.

If the drying results are not satisfactory we suggest that you:

1. Fill up the rinse aid dispenser with rinse aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to position 2.

● The activation/deactivation of the

rinse aid dispenser can only be possible with the Multi-tab function active.

daily use electrolux 25

If you decide to turn back to the use of standard detergent system we advise that you:

1. Deactivate the Multi-tab function.

2. Fill up the salt container and the rinse aid dispenser again.

3. Adjust the water hardness setting to the highest setting and perform 1 normal washing programme without loading any dishes.

4. Adjust the water hardness setting according to the hardness of the water in your area.

5. Adjust the rinse aid dosage.

Activation/deactivation of the rinse aid dispenser

1. Press the On/Off button. The dishwasher must be in setting mode.

2. Simultaneously press and hold buttons 2 and 3, until the lights of buttons 1, 2

and 3 start flashing.

3. Press button 2, the indicator lights of buttons 1 and 3 turn off while the indicator light of button 2 goes on flashing.

4. To activate the rinse aid dispenser, press button 2 again, the end of programme indicator light illuminates, indicating that the rinse aid dispenser has been activated.

5. To memorise the operation, switch off the dishwasher by pressing the On/Off button.

6. To deactivate the rinse aid dispenser again, follow the above instructions until the end of programme indicator light turns off.

26 electrolux daily use

Select and start a washing programme

Select the washing programme with the door slightly opened. The start of the programme will occur only after the closure of the door. Until then it is possible to modify the settings.

1. Check that the baskets have been

loaded correctly and that the spray arms are free to rotate

2. Check that the water tap is opened

3. Press the On/Off button. The

dishwasher must be in setting mode.

4. Press the programme selection

button until the light corresponding to the required washing programme illuminates; (see “Washing programmes” chart).

The phase indicator lights foreseen for that programme start flashing.

5. Close the dishwasher door, the

programme starts automatically. Once the programme has started

the phase indicator lights will turn off except for the phase under way.

Interrupt or cancel a washing programme in progress ONLY if it’s absolutely necessary. Attention! Hot steam may escape when the door is opened. Open the door carefully.

Interrupt a washing programme in progress:

● Open the dishwasher door; the

programme will stop. Close the door; the programme will start from the point at which it was interrupted.

● Press the On/Off button (all

indicator lights will turn off); the programme will stop. Press the On/Off button again; the programme will start from the point at which it was interrupted.

Cancel a washing programme in progress

● Simultaneously press and hold the

two programme buttons positioned over the letter C, until the washing programme light turns off and the programme selection button light and end of programme light are illuminated.

The washing programme has been cancelled.

● If a new washing programme is to

be selected, check that there is detergent in the detergent dispenser.

daily use electrolux 27

End of the washing programme

● The dishwasher will automatically

stop.

● The end of programme indicator

light is illuminated.

● The indicator light of the

programme just ended will remain illuminated.

1. Switch off the dishwasher by pressing the On/Off button.

2. Open the dishwasher door and leave it ajar; wait a few minutes before removing the dishes; in this way they will be cooler and the drying will be improved.

Unloading the dishwasher

● Hot dishes are sensitive to knocks.

The dishes should therefore be allowed to cool down before removing from the appliance.

● Empty the lower basket first and

then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one.

● Water may appear on the sides

and the door of the dishwasher as the stainless steel will eventually become cooler than the dishes.

When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off.

28 electrolux washing programmes

Washing programmes

Programme

Intensive

Heavy soil

Crockery,

cutlery, pots

and pans

Prewash Main wash up to 70°C 2 intermediate rinses Final rinse Drying

Degree of soil Type of load Programme description

Normal soil

Crockery and

cutlery

Prewash Main wash up to 50°C 1 intermediate rinse Final rinse Drying

Quick

Light soil

Crockery and

cutlery

Main wash up to 45°C 1 intermediate rinse Final rinse Drying

Normal ECO

(1)

Washing programmes information

(1)Test programme for test institutes.

care and cleaning electrolux 29

Cleaning the filters

The filters must be checked and cleaned from time to time. Dirty filters will degrade the washing result.

Coarse filter

The coarse filter (1) must be checked after every washing programme.

1. Open the door, remove the lower basket.

2. Remove the coarse filter and if necessary clean it thoroughly under running water.

3. Replace the coarse filter.

Fine filter

The fine filter (2) must be cleaned from time to time.

1. Open the door and remove the lower basket.

2. Take hold of the fine filter by the handle and remove by turning it to the right.

3. Clean the fine filter thoroughly with a brush under running water.

4. Put the fine filter back in the base of the washing compartment and ensure that it fits perfectly by turning to the left until you feel it click into place (arrow).

Before cleaning the filters ensure that the machine is switched off.

Care and cleaning

NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will produce poor washing results and will result in damage to the appliance.

30 electrolux care and cleaning

Cleaning the spray arms

Regularly check the nozzles in the 3 spray arms for blockages. If necessary clean the nozzles with a piece of fine wire or a fine needle and a strong water jet.

Do not damage the nozzle openings.

3. Clean the spray arm and the fixing screw.

4. Fasten the spray arm with the fixing screw (A) by turning it clockwise.

Ceiling spray arm

1. Undo the fixing screw (A) by turning it anti-clockwise.

2. Pull the spray arm off the shaft.

Upper basket spray arm

1. Remove the upper basket spray arm by turning it laterally.

2. Clean spray arm nozzles.

3. To replace the spray arm, press upwards until you feel it snap into place.

3. Clean the spray arm and the fixing screw.

4. Fasten the spray arm with the fixing screw (B) by turning it clockwise.

Lower spray arm

1. Undo the fixing screw (B) by turning it anti-clockwise.

2. Pull the spray arm off the shaft.

care and cleaning electrolux 31

External cleaning

Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene

etc....).

● Polished chromium steel

surfaces

Remove light dirt with a clean, damp, soft cloth. Microfibre cloths are particularly good.

When cleaning ensure that you do not go against the direction of the stainless steel finish (the fine horizontal lines).

No circular movements!

● Aluminium look surfaces

Remove light dirt with a clean, damp, soft cloth. Microfibre cloths are particularly good.

● Agents that scratch or scour are

not suitable.

● If required, use a commercially

available cleaner for chrome surfaces. Follow the manufacturer’s instructions when using these products.

Internal cleaning

Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth.

We recommend every 3 months to run the wash programme for heavy soiled dishes using detergent but without dishes.

Prolonged periods of nonoperation

If you are not using the machine for any prolonged period of time you are advised to:

1. Unplug the appliance and then turn off the water.

2. Leave the door ajar to prevent the formation of any unpleasant smells.

3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it.

Moving the machine

If you have to move the machine

(moving house etc....):

1. Unplug it.

2. Turn the water tap off.

3. Remove the water inlet and discharge hoses.

4. Pull the machine out together with the hoses.

Avoid over tilting the machine during transportation.

32 electrolux something not working

Something not working

The dishwasher will not start or stops during operation. Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the indications described in the chart, without calling out an engineer.

Switch off the appliance and carry out the following suggested corrective actions.

Fault code and malfunction Possible cause and solution

● continuous flashing of the light of the

running programme

● 1 flash of the “end of programme”

indicator light

The dishwasher does not fill with water

● The water tap is blocked or furred with

limescale. Clean the water tap.

● The water inlet hose has not been

correctly laid or it is bent or squashed. Check the water drain hose connection.

● The filter (where present) in the threaded

hose fitting at the water inlet valve is blocked. Clean the filter in the threaded hose.

● The water tap is turned off.

Turn the water tap on.

● continuous flashing of the light of the

running programme

● 2 flashes of the “end of programme”

indicator light

The dishwasher will not drain

● The sink spigot is blocked.

Clean out the sink spigot.

● The water drain hose has not been

correctly laid or it is bent or squashed. Check the water drain hose connection.

● continuous flashing of the light of the

running programme

● 3 flashes of the “end of programme”

indicator light

Anti-flood device is activated

● Close the water tap and contact your

local Service Force Centre.

something not working electrolux 33

Malfunction Possible cause and solution

The programme does not start ● The dishwasher’s door has not been

properly closed. Close the door.

● The main plug is not plugged in.

Insert the main plug.

● The fuse has blown out in the household

fuse box. Replace the fuse.

Once these checks have been carried out, switch on the appliance.

The programme will continue from the point at which it was interrupted.

If the malfunction or fault code reappears contact the Service Force Centre.

For other fault codes not described in the above chart, please contact your Service Force Centre.

Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC) and serial number (S.N.).

This information can be found on the rating plate located on the side of the dishwasher door.

So that you always have these numbers at hand, we recommend you to make a note of them here:

Mod. : . . . . . . . . . . . . . . . . . . . . . . .

PNC :. . . . . . . . . . . . . . . . . . . . . . . .

S.N. :. . . . . . . . . . . . . . . . . . . . . . . .

34 electrolux something not working

The wash results are not satisfactory

The dishes are not clean

● The wrong washing programme has been selected.

● The dishes are arranged in such a way as to stop water

reaching all parts of the surface. The baskets must not be overloaded.

● The spray arms do not rotate freely due to incorrect

arrangement of the load.

● The filters in the base of the washing compartment are

dirty or incorrectly positioned.

● Too little or no detergent has been used.

● Where there are limescales deposits on the dishes; the

salt container is empty or the incorrect level of the water softener has been set.

● The drain hose connection is not correct.

● The salt container cap is not properly closed.

The dishes are wet and dull

● Rinse aid was not used.

● The rinse aid dispenser is empty.

There are streaks, milky spots or a bluish coating on glasses and dishes

● Decrease rinse aid dosing.

Water drops have dries onto glasses and dishes

● Increase rinse aid dosing.

● The detergent may be the cause. Contact the detergent

manufacturer’s consumer care line.

If after all these checks, the problem persists, contact your local Service Force Centre.

technical data electrolux 35

Technical data

Dimensions Width 54.6 cm

75.9 cm

56.3 cm

Height Depth

Water supply pressure Minimum 0.5 bar (0.05 MPa)

8 bar (0.8 MPa)

Maximum

Capacity 11 place settings Max. weight 55.5 kg

Electrical connection Voltage - Overall power Fuse

Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher’s door

Subject to change without notice

36 electrolux technical data

The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply and the amount of dishes.

Consumption values

Programme

duration

(in minutes)

Programme Energy

consumption

(in kWh)

Water

consumption

(in litres)

116 - 125Intensive 1.9 - 2.1 22 - 24

175

Normal ECO

(Test programme for test institutes)

1.0 14

65 - 75

Quick

0.8 - 0.9

13 - 14

hints for test institutes electrolux 37

Hints for test institutes

Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Consumption values").

Test in accordance with EN 50242 must be carried out when the salt container and rinse aid dispenser have been filled with salt and rinse aid respectively and using the test programme (see "Consumption values").

Full load: 11 standard place settings

Amount of detergent required: 27,5 (Type B) Rinse aid setting: position 6 (Type III)

Arrangement cutlery basket

3 3 33 333 3333

1111111111111

5 5 55 555 5555

4 4 44 444 4444

2 2 22 222 2222

1 2 3 4 5 6 7 8

38 electrolux hints for test institutes

Arrangement upper basket

(upper basket in lowered position)

Arrangement lower basket

installation electrolux 39

Installation

Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person.

Remove all packaging before positioning the machine.

If possible, position the machine next to a water tap and a drain.

This dishwasher is designed to be fitted under a kitchen counter or worksurface.

No further openings for the venting of the dishwasher are required, but only to let the water fill and drain hose and power supply cable pass through.

During all operations that involve accessibility to internal components the dishwasher has to be unplugged.

When inserting the machine, ensure that the water inlet hose, the drain hose and the supply cable are not kinked or squashed.

Fixing to the adjacent units

The dishwasher must be secured against tilting. Therefore make sure that the counter it is fixed under, is suitably secured to a fixed structure (adjacent kitchen units cabinets, wall).

A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot.

For making the connection itself, the coupling nut fitted to the machine’s supply hose is designed to screw onto a 3/4" gas thread spout or to a purpose made quick-coupling tap such as the Press-block.

The water pressure must be within the limits given in the "Technical data". Your local Water Authority will advise you on the average mains pressure in your area.

The water inlet hose must not be kinked, crushed, or entangled when it is being connected.

The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut.

The locknut must be correctly fitted to avoid water leaks.

(Attention! NOT all models of dishwashers have fill and drain hoses provided with locknut. In this case, this kind of facility is not possible).

If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose.

DO NOT use connection hoses which have previously been used for an old appliance.

Installation of an IRG filter is recommended on the construction side.

Water supply connections

This dishwasher may be fed with either hot (max. 60°) or cold water. Nevertheless we advise you a cold water supply.

40 electrolux installation

Water inlet hose with safety valve

After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water.

Please take care when installing the water inlet hose:

● The electrical cable for the safety

valve is in the double-walled water inlet hose. Do not immerse the water inlet hose or the safety valve in water.

● If water inlet hose or the safety

valve is damaged, remove the mains plug immediately.

● A water inlet hose with safety valve

must only be replaced by the Service Force Centre.

● Place the water inlet hose in such

a way that it is never higher than the bottom edge of the safety valve.

Warning! Dangerous voltage

Water outlet hose connection

The drain hose can face either to the right or left of the dishwasher

Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water.

The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine.

The waste connection must be at a maximum height of 70 cm from the ground.

A = drain outlet G = size of the appliance K = cold water supply N = size of the recess W = hot water supply E = socket

WKE

N 762+3105N 600

G 759

G 57020

G 546

N 550

100 180

550

400

max. 700

600

installation electrolux 41

Our appliances are supplied with a security device to protect against the return of dirty water back into the machine. If the spigot of your sink has a ‘no return valve’ incorporated this can prevent the correct draining of your dishwasher. We therefore advise you to remove it.

When connecting the drain hose to an under sink trap spigot, the entire

plastic membrane (A) must be removed. Failure to remove all the

membrane will result in food particles building up over time eventually blocking the dishwasher drain hose spigot

Electrical connection

Safety standards require the appliance to be earthed.

Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate.

Always plug the mains plug into a correctly installed shockproof socket.

Multi-way plugs, connectors and extension cables must not be used. This could constitute a fire hazard through overheating.

If necessary, have the domestic wiring system socket replaced. In case that the electrical cable has to be replaced, contact your local Service Force centre.

The plug must be accessible after the appliance has been installed.

Never unplug the appliance by pulling on the cable. Always pull the plug.

The manufacturer accepts no liability for failure to observe the above safety precautions.

42 electrolux installation

1. Stand the appliance in front of the kitchen unit. Place cable and hoses into the neighbouring unit.

2. Push the appliance in, pull the cable and hoses through and ensure that they are not kinked or squashed.

3. Line up the appliance and fix it on both sides in the upper area of the tub casing.

Other fixing possibilities:

on the plinth

Additional bracket on the top available as special accessory (contact your local Service Force Centre)

105

environment concerns electrolux 43

Packaging material

The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities.

When a unit is no longer being used:

- Pull the plug out of the socket.

- Cut off the cable and plug and

dispose of them.

- Dispose of the door catch. This

prevents children from trapping themselves inside and endangering their lives.

Environment concerns

Old appliance

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

44 electrolux warranty/point of service

Servicestellen Points de service Servizio dopo vendita Point of service

Ersatzteilverkauf / Point de vente de rechange / Vendita pezzi di ricambio /

spare parts service

5506 Mägenwil/Zürich Industriestr. 10

9000 St. Gallen Zürcherstrasse 204 e

4127 Birsfelden Hauptstrasse 52

6020 Emmenbrücke Seetalstrasse 11

7000 Chur Comercialstrasse 19

3018 Bern Morgenstrasse 131

1028 Préverenges Le Trési 6

6916 Grancia Zona Industriale E

55 Mägenwil, Industriestrasse 10, Tel. 0848 848 023

Fachberatung, Verkauf/Demonstration, Vente/Consulente (cucina),

Vendita/consulting, sales

8048 Zürich, Badenerstrasse 587, Tel. 044 405 81 11

Warranty/Point of service

Service-Helpline

0848 848 111

service@electrolux.ch

warranty/point of service electrolux 45

Garantie

Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum an den Endverbraucher eine Garantie von 2 Jahren. (Ausweis durch Garantieschein, Faktura oder Verkaufsbeleg). Die Garantieleistung umfasst die Kosten für Material, Arbeitsund Reisezeit.

Die Garantieleistung entfällt bei Nichtbeachtung der Gebrauchsanweisung und Betriebsvorschriften, unsachgerechter Installation, sowie bei Beschädigung durch äussere Einflüsse, höhere Gewalt, Eingriffe Dritter und Verwendung von Nicht-Original Teilen.

Garantie

Nous octroyons sur chaque produit 2 ans de garantie à partir de la date de livraison ou de la mise en service au consommateur (documenté au moyen d’une facture, d’un bon de garantie ou d’un justificatif d’achat). Notre garantie couvre les frais de mains d’oeuvres et de déplacement, ainsi que les pièces de rechange.

Les conditions de garantie ne sont pas valables en cas d’intervention d’un tiers non autorisé, de l’emploi de pièces de rechange non originales, d’erreurs de maniement ou d’installation dues à l’inobservation du mode d’emploi, et pour des dommages causés par des influences extérieures ou de force majeure.

Garanzia

Per ogni prodotto concediamo una garanzia di 2 anni a partire dalla data di consegna o dalla sua messa in funzione. (Fa stato la data della fattura, del certificato di garanzia o dello scontrino d’acquisto) Nella garanzia sono comprese le spese di manodopera, di viaggio e del materiale.

Dalla copertura sono esclusi il logoramento ed i danni causati da agenti esterni, intervento di terzi, utilizzo di ricambi non originali o dalla inosservanza delle prescrizioni d’istallazione ed istruzioni per l’uso.

Warranty

For each product we provide a two-year guarantee from the date of purchase or delivery to the consumer (with a guarantee certificate, invoice or sales receipt serving as proof). The guarantee covers the costs of materials, labour and travel.

The guarantee will lapse if the operating instructions and conditions of use are not adhered to, if the product is incorrectly installed, or in the event of damage caused by external influences, force majeure, intervention by third parties or the use of non-genuine components.

46 electrolux

Notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

117987 91/0-00-28032007

www.electrolux.com

www.electrolux.ch

AEG-Electrolux GA552F101 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual