AEG-Electrolux FAV54750VI, F54750VI User Manual

ÖKO_FAVORIT 54750 VI

Dishwasher

Operating instructions

2

Dear customer

Please read these user instructions carefully.
Above all please observe the safety instructions on the first few pages of

these user instructions! Please keep these user instructions for later reference.
Pass them on to any subsequent owner of the appliance.

The warning triangle and/or specific words (Warning!, caution!, Important!)
are used to highlight instructions that are important for your safety or for the
function of the appliance. It is imperative that these instructions are
observed.

Numbered instruction steps lead you step by step through the operation of
the appliance.

Next to this symbol you receive additional information and practical tips on
using the appliance.

Tips and instructions for the economical and environmentally conscious use
of the appliance are marked with a clover leaf.

In the event of a malfunction, these operating instructions contain
information on how to rectify faults yourself, see "What to do, if..." section.

For further assistance contact your local AEG Service Force Centre, see the
chapter "Service & Spare Parts".

Printed on paper manufactured with environmentally sound processes.
He who thinks ecologically acts accordingly...

3

Contents

Safety instructions 4
Disposing of packaging and old machines 6

Disposing of the packaging 6
Disposing of your old machine 6
Economical and ecological dishwashing 7

Description of the appliance 8

The inside of the appliance 8
Control panel 8
Before using your dishwasher for the first time 10
Setting the water hardness range 10
Filling with special salt 12
The rinse aid 13

Loading cutlery and dishes 14

The lower basket 15
Cutlery basket 15
The upper basket 16
Adjusting the height of the upper basket 17
Use of detergent 18
Bio programmes and compact powders 19

Washing programmes 20
Operating instructions 22
Maintenance and cleaning 24

Internal and external cleaning 24
Cleaning the filters 24

What do do, if... 26
Service & Spare Parts 28
Guarantee Conditions 29
European Guarantee 30

Hints for test centres 31
Technical data 32
Installation and connection instructions 33

Connecting to the water supply 33
Water outlet connection 33
Water protection system 34
Electrical connection 34

4

Safety instructions

The safety of AEG electrical appliances conforms to accepted rules of technology and
the Appliance Safety Act. We as manufacturers, however, see ourselves as being
obliged to familiarise you with the following safety instructions.

Using your dishwasher for its intended purpose

● Only use your dishwasher for machine washing of household crockery. If your

machine is misused or used for any purposes other than that for which it is
intended, the manufacturer cannot be held liable for any damage caused.

● For safety reasons, you should not convert or modify your dishwasher in any way.

Before using your dishwasher for the first time

● Check your dishwasher for any transport damage. Never connect a damaged

machine. If your dishwasher is damaged, you should contact your supplier.

● Your dishwasher must be correctly installed and connected. Please read the

section on "Installation" to make sure you know all about this.

● Before using your dishwasher for the first time, do not forget that the nominal

voltage and current type indicated on the rating plate of your machine must be
the same as the nominal voltage and current type at the installation site. The
necessary electrical fusing is also given on the rating plate.

Child safety

● Packaging parts (e.g. foils, styrene foam) may be dangerous for children,who could

even be suffocated! You should therefore keep all packaging well away from
children.

● Children may not recognise the dangers of improper use of electrical appliances.

You should therefore ensure proper supervision during operation and not allow
your children to play with your dishwasher.

● Detergents may have a caustic effect on eyes, mouth and throat and may even

cause suffocation! Keep all detergents in a safe place out of children’s reach.

● The water in your dishwasher should not be used for drinking. Detergent residues

may still be present in your machine. Make sure you do not splash these caustic
residues onto your skin or suffocate yourself! Keep children well away from your
dishwasher when its door is open.

5

Your dishwasher in day-to-day use

● Never operate your dishwasher if the electrical supply lead, supply or drainhose,

control panel, worktop or plinth are damaged.

● If there is a fault, first turn the water tap off. Then switch off your machine and

pull the plug out of the socket. If there is a fixed connection, switch off or
unscrew the fuse(s).

● Never pull the plug out of the socket by the cable - always hold the plug.

● Dishwasher repairs should only be performed by trained personnel.

Improper repairs may seriously endanger the user. If your dishwasher needs to be
repaired, you should contact our service centre or your retailer.

● Never place any solvents in your dishwasher or you may cause an explosion!

● Do not rest or sit on the open door as the machine could tilt.

● Before using special dishwasher salt, detergent or rinse-aid, make sure that the

manufacturer of these products expressly specifies their use in domestic
dishwashers.

● Always turn off the water tap when your dishwasher is left unattended for any

length of time, e.g. when you are away on holiday.

● Only transport the dishwasher in an upright position. Tipping it upside down

during transport could cause salty water to leak into the internal compartment
and lead to the formation of rust.

Marking of plastic parts for graded recycling: all plastic parts in your machine are
marked with internationally standardised abbreviations (e.g. <PS> for polystyrene).
When your machine is disposed of, this enables plastic waste to be sorted into
individual types for environmentally conscious recycling.

Check with your local Council or Environmental Health Office to see if there are
facilities in your area for recycling the appliance.

Warning! Children at play could lock themselves in your machine
(and suffocate) or otherwise endanger their lives. Therefore pull out
the main plug and detach and discard the electrical supply lead.
Disable the door lock so that the door no longer closes.

6

Disposing of packaging and old machines

Warning! Packaging parts (e.g. foils, styrene foam) may be dangerous
for children and can cause suffocation. You should therefore keep all
packaging well away from children.

Disposing of the packaging

Our dishwashers require effective protective packaging in transit, though we always
confine ourselves to what is absolutely necessary.

All packaging materials used are environmentally compatible and reusable.
The cardboard parts are produced from recycled paper, and the wood is untreated.
The plastics are marked as follows:

>PE< for polyethylene, e.g. packaging foils.
>PS< for polystyrene, e.g. padding (essentially CFC-Free).
>POM< for polyoxymethylene, e.g. plastic clamps.

Give the packaging for reuse to your local recycling centre. Your municipal or local
authority will give you its address.

Disposing of your old machine

When your machine finally reaches the end of its life and you withdraw it from
service, you should render it unserviceable before having it disposed of.

7

Economical and ecological dishwashing

● Ensure that the water softener is correctly adjusted.

● Do not pre-rinse under running water.

● Select the wash programme to suit the nature and degree of the soiling on the

dishes.

● Do not use more detergent, special salt or rinse aid than is recommended in these

operating instructions and by the manufacturer of the respective product.

8

1. On/off push button

2. Salt r efilling indicator light

3. Pr ogramme selector push buttons

4. On/Off indicator light

1234

Control panel

Description of the appliance

2

3

4

5

6

7

8

9

IN97

1

The inside of the appliance

1. Upper basket stop

2. Upper spray arm

3. Salt container

4. Detergent dispenser

5. Control panel

6. Rinse aid dispenser

7. Filters

8. Lower spray arm

9. Upper basket

9

Audible signals have been introduced to help indicate which operations the
dishwasher is performing.

"Instruction accepted" audible signal

When any of the push buttons are pressed, an audible signal informs you that the
machine has accepted the instruction given.

"Programme run" audible signal

An audible signal informs you that the washing programme is starting.

"End of programme" audible signal

An intermittent audible signal informs you that the wash programme has ended.

"Alarm" audible signal

The machine is fitted with a number of alarm systems to help you determine the
cause of any problems (see "What to do, if...).
An audible signal informs you that an alarm is activated.

To deactivate these audible signals, press simultaneously "Intensive 70°" and
"Normal 65°" push buttons, after about 3 seconds an audible signal informs you that
the audible signals have been deactivated.

To reactivate these audible signals, press simultaneously "Intensive 70°" and
"Normal 65°" push buttons, after about 3 seconds an audible signal informs you that
the audible signals have been reactivated.

Both operations (to deactivate or reactivate the audible signals) must be carried out
before starting a washing programme; the setting will remain memorised after
switching off the dishwasher.

SO291

10

Before using your dishwasher for the first time

1. Ensure that the electrical and water connections comply with the

installation instructions.

2. Remove all packaging from inside the appliance.

3. Set the water softener.

4. Pour half a litre of water inside the salt container and then fill with salt.

5. Fill the rinse-aid dispenser.

Setting the water hardness range

The dishwasher is equipped with a water softener designed to remove minerals and
salts from the water supply, which would have a detrimental or adverse effect on the
operation of the appliance.

The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, German, French degrees and PPM

(parts per Million).
The softener should be adjusted according to the hardness of the water in your area.

Your local Water Authority can advise you on the hardness of the water in your area.
The dishwasher is factory set at level 3.

If this level is not suitable for your area the softener should be adjusted.
You may change the factory level setting by means of the wash programme selector

push buttons. Each button corresponds to a different level.

Level 1 = "RINSE & HOLD" push button
Level 2 = "INTENSIVE 70°" push button
Level 3 = "NORMAL 65°" push button
Level 4 = "BIO 50°" push button
Level 5 = "QUICK 50°" push button

11

To set a different level, proceed as follows:

1. Press the "Intensive 70°" and "Bio 50°" programme push buttons simultaneously

for about 5 seconds. The pilot light corresponding to the current level flashes.

2. Press within 5 seconds the programme push button corresponding to the
required level. After 5 seconds the dishwasher will memorise the new level setting
and will return to programme setting mode.

The setting will remain memorised after switching off the dishwasher.

If your water hardness is level 1 it is already soft and therefore there is no need
to use salt. With the setting of the water softener at level 1 the salt indicator
light on the control panel will always remain off.

Water hardness

dH°

(german degrees)

°TH

(french degrees)

PPM

(parts per million)

Use

of salt

Level

0 - 8

9 - 20
21 - 40
41 - 70
71 - 90

0 - 4

5 - 11
12 - 22
23 - 39
40 - 50

0 - 80

81 - 200
201 - 400
401 - 700
701 - 900

NO
YES
YES
YES
YES

1
2
3
4
5

SO292

To fill:

1. To fill with salt, unscrew the cap of the

salt container.

2. Pour half a litre of water inside the
container (this is necessary only
before filling with salt for the first
time).

3. Using the funnel provided, pour in the

salt until the container is full.
Do not worry if water overflows from
the unit when filling with salt, this is
quite normal.

4. Replace the cap making sure that
there is no trace of salt on the screw
thread or on the gasket.

5. Screw on the cap tightly.

When this has been done, all that is required is to periodically top up the container
with salt.
You are reminded of this by the salt indicator light on the control panel which will
illuminate when the salt has finished.

Important!

The salt refill indicator light on the control panel can remain illuminated for 2-6
hours after salt has been replenished, assuring the dishwasher remains on. If you are
using salts that take longer to dissolve then this can take longer. the function of the
dishwasher is not affected.

12

Filling with special salt

Caution! The packaging of dishwasher salt and detergents are often very similar. The

accidental filling of the salt compartment with detergent would ruin the water
softener. Each time you add salt, make sure the carton you have in your hand really
is salt.

Only use salt specifically designed for use in dishwashers.
All other types of salt not specifically designed for use in a dishwasher,
especially table salt, will damage the water softener.
Only fill with salt just before starting one of the complete washing
programmes (not the "Rinse and hold" programme). This will prevent
any grains of salt or salty water, which may have been spilled,
remaining on the bottom of the machine for any period of time, which
may cause corrosion.

SR14

SALE

SALT

SALZ

SEL

13

The rinse-aid

The rinse-aid ensures brilliant crockery and also helps it to dry. It is automatically
dosed in during the hot rinsing cycle. The storage compartment built in to the inside
of the door can hold about 110 ml of rinse-aid, which will be sufficient for between
16 and 40 dishwashing programmes, according to the dosage setting.

Filling up the rinse-aid

1. Open the container by turning the

lid (A) anticlockwise.

2. Add the rinse aid until the
container is completely full. The
indicator (B) will be completely
dark.

Ensure that the lid is closed after every
refill.

Top up with rinse aid when the indicator (B)
becomes clear.

Clean up any rinse aid spilt during filling with
an absorbent cloth to avoid excess foaming
during the next wash.

Attention! Do not put liquid detergent in
the rinse aid compartment.

Adjusting the dose

The correct dosage of the rinse-aid should
be regulated on the basis of the shine and
drying results.

For this purpose, set the quantity of liquid
by means of the six-position selector (C)
located on the inside of the filler opening
(minimum quantity is position 1,
maximum quantity is position 6).

Use the tip of a knife or a screwdriver to
rotate the selector. If drops of water or
white marks remain on the crockery after
it has been washed, increase the dosage. If
the crockery comes out with whitish,
sticky streaks, reduce the dosage.

BR01

BR03

BR02

14

Loading cutlery and dishes

Sponges, household cloths and any object that can absorb water must not
be washed in the dishwasher.

For washing in the dishwasher the following cutlery/dishes

are not suitable:

● Cutlery with wooden, horn, china or

mother of pearl handles.

● Plastic items that are not heat resistant.

● Older cutlery with cement that is not

temperature resistant.

● Bonded cutlery items or dishes.

● Pewter or copper items.

● Lead crystal glass.

● Steel items subject to rusting.

● Wooden platters.

● Items made from synthetic fibres.

● Only wash stoneware in the dishwasher

if it is specifically marked as being
dishwasher-safe by the manufacturer.

● Glazed patterns may fade if machine

washed frequently.

● Silver and aluminium parts have a

tendency to discolour during washing.
Left-overs, e.g. egg white, egg yolk and
mustard often cause discolouring and
staining on silver. Therefore always
clean left-overs from silver immediately,
if it is not to be washed straight after
use.

● Some types of glass can become dull

after a large number of washes.

are of limited suitability:

Attention!
When buying new dishes, ensure that they are dishwasher proof.

Before placing dishes in the machine, remove any scraps of food, to avoid clogging
the filters and consequently reducing the performance.

Open the door and slide out the baskets.

Do not load very small items which can fall through the baskets.

15

The lower basket

The lower basket is designed to take saucepans, lids, plates, salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the edge of the basket,

ensuring that the upper spray arm can turn freely.

Cutlery basket

Place knives, forks and spoons in the cutlery basket with their handles pointing
downwards.

Arrange cutlery loosely and distribute it in all compartments so that each individual
article has good contact with washing water. Also do not arrange spoons and forks
with their dirty side in contact with each other.

Important! Exceptionally long cutlery, such as soup ladles, kitchen knives, or the like,
may obstruct the upper spray arm. Such cutlery can be placed in the upper basket.

To unload your dishwasher more easily, you can take the cutlery basket out of the
lower basket and unfold it. this makes it easier to remove small pieces of cutlery.

Important note! To prevent the full cutlery basket from inadvertently unfolding
when being taken out, place your hand right round the two-piece handle and hold it
firmly.

1. Place the cutlery basket on a firm support (table, worktop) and unfold
both handle parts.

2. After unloading, fold back both handle parts.

UI12

UI51

UI20

UI25

16

The upper basket

The upper basket is designed for plates (dessert plates, saucers, dinner plates up to 24
cm in diameter), salad bowls, cups and glasses; these should be arranged as shown in
the pictures.

Glasses with long stems can be placed upside-down in the raised cup-racks.
The cup-rack on the left folds upwards to increase your loading flexibility.
Arrange items on and underneath the fold-down cup racks so that water can reach

all surfaces.
Light items (plastic bowls etc.) should be loaded in the upper basket and arranged so

they do not move.

Before closing the door , ensure that the spr ay arms can r otate freely.

Long bladed knives stored in an upright position are a
potential hazard.

Long and/or sharp items of cutlery such as carving knives must
be positioned horizontally in the upper basket.

Take care when loading or unloading sharp items such as
knives.

US60

17

Adjusting the height of the upper basket

If washing very large plates (over 27 cm and up to 31 cm in diameter) you can load

them in the lower basket after moving the upper basket to the higher position.

To move to the higher position
proceed as follows:

1. Move the front runner stops (A) of

the upper basket outwards and
slide the basket out.

2. Refit the basket in the higher
position and replace
the stops (A) in their original
position.

Attention!
When the top basket is in the higher position it will only take plates up to 20
cm in diameter and you will not be able to use the raised cup racks.

After loading your machine always close the door, as an open door can
be a hazard.

RC01

18

Use of detergent

Attention!
Only use detergents specifically designed for use in dishwashers.

If using powder detergents
proceed as follows:

1. Open the dispenser lid by pulling the

catch (D).

2. Add the detergent. As all detergents
are not the same, please pay attention
to the dosage instructions from the
manufacturer of your brand.

3. Always close the lid.

4. If the programme has a prewash add

the required detergent over the lid of
the dispenser.

If using detergent in tablets
proceed as follows:

1. For all programmes; place 1 tablet

inside the detergent dispenser.

2. Always close the lid.

3. For all programmes with prewash;

place a portion of a further tablet
on the lid of the detergent dispenser.

At the end of any washing programme the lid is always open, ready for the next
wash.

Since not all detergents are the same, you should also consult the instructions on the
packet.

DE17

DE02

19

Remember that insufficient quantities of detergent will produce poor
washing results whereas an excessive amount of detergent does not
improve washing results and is also wasteful.

BIO programmes and compact powders

On the basis of their chemical composition, dishwasher detergents can be classified
into two groups:

- conventional, alkaline detergents with caustic components:

- low-alkaline compact powders with natural enzymes.
The enzymes in low-alkaline compact powders have a dirt-dissolving effect and are

also biodegradable. These enzymes deploy their full dirt-dissolving power within a
temperature range of 40-50°C. In BIO washing programmes, the temperature range
and duration of the heating phases are precisely matched to the dirt-dissolving
properties of the enzymes.

In combination with low-alkaline compact powders, BIO washing programmes, at a
temperature as low as 50°C, therefore achieve the same cleaning results that would
otherwise be achievable only with 65°C programmes.

The lack of any caustic components in low-alkaline compact powders and the lower
cleaning temperature of BIO washing programmes are not only environmentally
friendly, but also care for your crockery.

Using no more than the correct amount of detergent also contributes to
reducing pollution.

20

*

This is a quick wash programme for a full load of lightly soiled dishes, glasses and
crockery (except pots) so that you may re-use them promptly.
Due to the shortness of this programme, no drying phase is provided.

Washing pr ogrammes

Programmes

Intensive

70°C

Normal

65°C

Bio

50°C

*

Quick

50°C

Rinse and

hold

Type of soil
Type of load

Heavy soil.
Crockery, cutlery,
pots and pans

Normal soil.
Crockery and cutlery

Normal soil.
Crockery and cutlery

Light soil.
Crockery and party crockery

Partial load to be completed later
in the day. This programme does
not require detergent.

Required
push buttons

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

RINSE & HOLD

INTENSIVE
70°

NORMAL
65°

BIO
50°

QUICK
50°

21

Programme
duration in

minutes

Energy

consumption

in kWh

Water

consumption

in litres

Cycle description

Approximate values

**

10

0,1

8

105 - 115

1,4

18

90 - 100

1,2

15

135 - 145

0,8

14

35 - 45

0,7

11

Warm prewash
Main wash up to 65°C
1 cold rinse
1 hot rinse
Drying

Cold prewash
Main wash up to 50°C
1 cold rinse
1 hot rinse
Drying

Main wash up to 50°C
1 cold rinse
1 hot rinse

Hot prewash
Main wash up to 70°C
2 cold rinses
1 hot rinse
Drying

1 cold rinse
(to avoid food scraps from sticking
to the dishes).

**

The times and consumption values are intended as a guide, and depend on the
pressure and temperature of the water and also by the variations of the power
supply.

22

Operating instructions

In this fully integrated appliance the controls are located on the top of the door.
When selecting a programme, the door needs to be partially opened.

1. Check the filters

Ensure they are clean and properly positioned (see "Maintenance and cleaning").

2. Press the On/Off push button

The On/Off indicator light will illuminate.

3. Check that there is rinse aid and salt

The salt indicator light will illuminate if refilling is necessary.

4. Load the dishes

Remove any scraps of food.
Pull the lower basket out and arrange the saucepans, plates and cutlery in it.
Pull the upper basket out and arrange the plates, saucers, glasses and cups etc.

in it.
Slide the baskets back into the machine.

5. Ensure that the spray arms can rotate freely.

6. Add the detergent

As all detergents are not the same, you should also consult the instructions on
the packet.
Close the detergent dispenser lid.

7. Setting the programme

Press the programme push button which corresponds to the washing
programme you wish to select, the corresponding programme indicator light
starts flashing.

8. Start the programme

Open the water tap.
Close the dishwasher door.
An audible signal informs you that the programme has started. The indicator

light of the programme under way is now permanently on.

9. At the end of the washing programme

The dishwasher will automatically stop and an audible signal informs you that
the programme has ended.

The "On/Off" indicator light flashes and the indicator light of the programme
turns off.

23

Open the door and press the On/Off push button to switch the dishwasher off.
Wait a few minutes before removing the dishes, in this way they will be cooler

and the drying will be improved.
Empty the lower basket first and then the upper one, this will avoid water

dripping from the upper basket onto the dishes in the lower one.
When the wash programme has finished, it is recommended that the dishwasher

is unplugged and the water tap turned off.

10. To cancel a programme in progress

If the door has not been closed and the wash programme has not started,

to cancel the programme simply press the push button of a different wash
programme.

To cancel a wash programme in progress, open the door and press the push
button of the programme under way until the relevant indicator light goes out.
The dishwasher is now in setting mode and a new washing programme can be
selected.

Interrupting a programme

- A programme underway is interrupted when you open the door.

- Close the door again. The programme will start again at the point it was
interrupted.

Caution!
Opening the door could let very hot steam escape: you risk being
scalded! Open the door with great care.
Do not open the door during the hot phase: this may cause hot water
escape.

Caution!
In general it is not advisable to open the door while the machine is
working; if the door is opened however, a safety device ensures that the
machine stops.

24

Maintenance and cleaning

Internal and external cleaning

Do not under any circumstances use furniture care products or aggressive
cleaners.

If necessary, clean the controls only with a soft cloth and pure warm water.
The spray arms do not need cleaning.
Occasionally check the internal containers, door seal and water inlet for soiling,

clean if necessary.
We recommend every 3 months to run a 65°C wash programme without dishes using

detergent.

Cleaning the filters

The filters in the base of the washing compartment are to a large extent self­cleaning. Nevertheless the filters should be checked and cleaned from time to
time. Dirty filters will degrade the washing result.

1. Open the door, remove the lower
basket.

2. The dishwasher filter system comprises
a coarse/fine filter, microfilter and a
flat filter.
Unlock the filter system using a handle
on the microfilter, and remove.

3.Turn the handle about

1

/4a turn

anticlockwise and remove.

4. Take hold of the coarse/fine filter (1/2)
by the handle with the hole and
remove from the microfilter (3).

5. Clean all filters thoroughly under
running water.

MA15

MA17

25

6. Remove the flat filter (4) from the base
of the washing compartment and clean
both faces thoroughly.

7. Put the flat filter back in the base of
the washing compartment.

8. Place the coarse/fine filter in the
microfilter and press together.

9. Put the filter combination in place and
lock by turning the handle clockwise to
the stop.
During this process ensure that the flat
filter does not protrude above the base
of the washing compartment.

Under no circumstances must the dishwasher be used without filters.

MA16

4

26

What to do, if...

Try to rectify minor faults on the dishwasher with the aid of the instructions given
here.

...a flashing fault code appears

If on the control panel one or more programme indicator lights are flashing, they are
indicative of a fault in the dishwasher that you can probably rectify yourself.

Open the door, press the On/Off push button to switch the dishwasher off and with
the aid of the malfunctions listed below try to rectify the fault condition.

Fault code

"RINSE & HOLD" and
"NORMAL 65°" indicator
lights are flashing

"INTENSIVE 70°" and
"NORMAL 65°" indicator
lights are flashing

"NORMAL 65°" indicator
light is flashing

Other indicator lights or
combinations of indicator
lights are flashing

The water tap is closed. Open the water tap.
The mains water supply has

been cut off.

Wait for the supply to be
restored.

The inlet hose may be
squashed or bent.

The inlet hose may be
blocked.

The drain hose may be
squashed or bent. The drain
hose extension is not
correct.

The sink may be blocked.

Protection against flooding
is active.

General

Close the water tap and
contact the Service Force
Centre.

Open the door, switch off
the dishwasher, switch
back on and start a wash
programme. If the fault
code reappears contact
the Service Force Centre.

Clear any blockages.

Reposition correctly the
drain hose. Follow the
instructions for
connecting to the waste.

Switch off the water
supply and clean the filter.

Reposition correctly the
hose.

Possible cause Remedy

Once you have checked the possible causes listed above, switch on the dishwasher
and start a wash programme, if the fault code reappears contact the Service Force
Centre.

27

...problems occur during use of the dishwasher

Malfunction

the programme does not
start

The machine is noisy

The door is difficult to
close

The door is not properly
closed.

Shut the door.

The plug is not properly
inserted in the power
socket.

Insert the plug.

There is a power failure.
Dishes are rattling against

each other.
The spray arms are
knocking against the
dishes.

The dishwasher is not level,
or not properly built-in.

Load correctly crockery,
cutlery, pots and pans.
Refer to "Loading cutlery
and dishes"

Refer to "Installation"
instructions.

Check the fuse.,

Possible cause Remedy

...the wash results are not satisfactory

Visible lime deposits or white film on the dishes

● Check that the right level of the water softener is set.

● Check that there is salt.

The dishes are not quite dry

● The rinse aid has run out or too little is being used.

The dishes are not clean

● The baskets are too full.

● The dishes have not been arranged properly.

● The spray arms do not rotate because of incorrect loading of the baskets.

● The filters are clogged.

● The filters are not in position.

● Not enough detergent has been used or it is unsuitable.

● The detergent is old or has gone hard.

● The salt container cap is not properly closed.

● The washing programme is too gentle.

28

Service & Spare Parts

In the event of your appliance requiring service, or if you wish to purchase
spare parts, contact your local AEG Service Force Centre by telephoning

08705 929 929

Your call will be automatically routed to the Service Centre covering your
post code area.

For the address of your local Service Force Centre and further informations about
Service Force, please visit the website at www.serviceforce.co.uk

Help us to help you

Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know,

1 Your name, address and post code
2 Your telephone number
3 Clear and concise details of the fault code
4 Date of purchase
5

● E-NR (product number)

● F-NR (serial number)

This information can be found on
the rating plate located on the right
inside edge of the door.

Customer Care

For general enquiries concerning your AEG appliance, or for further
information on AEG products, you are invited to contact our Customer Care
Department by letter or telephone at the address below or visit our website
at www.aeg.co.uk

Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough
Berkshire
SL1 1DZ

Tel.: [phone] (*)

*

calls to this number may be recorded for training purposes

M
o
d
.
.
.

.
.
.
.

P
.
.

r

o

d

.

N

o

.
.
.
.
.
.
.
.
.

S
e
r
.
N
o

.
.
.
.
.
.
.
.

.
.

E- NR

......

F-NR

......

29

Guarantee Conditions

AEG offer the following guarantee to the first purchaser of this appliance:

1. The guarantee is valid for 12 months commencing when the appliance is
handed over to the first retail purchaser, which must be verified by
purchase invoice or similar documentation.
The guarantee does not cover commercial use.

2. The guarantee covers all parts or components which fail due to faulty
workmanship or faulty material. The guarantee does not cover appliances
where defects or poor performance are due to misuse, accidental
damage, neglect, faulty installation, unauthorised modification or
attempted repair, commercial use or failure to observe requirements and
recommendations set out in the instruction book.
This guarantee does not cover such parts as light bulbs, removable
glassware or plastic.

3. Should guarantee repairs be necessary the purchaser must inform the
nearest customer service office (AEG’s service or authorised agent). AEG
reserves the right to stipulate the place of the repair (i. e. the customer’s
home, place of installation or AEG workshop).

4. The guarantee or free replacement includes both labour and materials.

5. Repairs carried out under guarantee do not extend the guarantee period

for the appliance. parts removed during guarantee repairs become the
property of AEG.

6. The purchaser’s statutory rights are not affected by this guarantee.

30

European Guarantee

If you should move to another country within Europe then your guarantee moves
with you to your new home subject to the following qualifications:

● The guarantee starts from the date you first purchased your product.

● The guarantee is for the same period and to the same extent for labour and parts

as exist in the new country of use for this brand or range of products.

● This guarantee relates to you and cannot be transferred to another user.

● Your new home is within the European Community (EC) or European Free Trade

Area.

● The product is installed and used in accordance with our instructions and is only

used domestically, i. e. a normal household.

● The product is installed taking into account regulations in your new country.

Before you move please contact your nearest Customer Care Centre, listed below, to
give them details of your new home.They will then ensure that the local Service
Organisation is aware of your move and able to look after you and your appliances.

France Senlis [phone]
Germany Nürnberg [phone]
Italy Pordenone [phone]
Sweden Stockholm [phone]
UK Slough [phone]
Ireland Dublin [phone]

31

Hints for test centres

Before starting any test it is necessary to fill completely with salt the salt container
and with rinse aid the rinse aid dispenser.

Test standard

Load
Rinse aid selector

Detergent dosage

Reference programme

EN 50242

position 4

- 20 g in the dispenser

- 5 g on the dispenser lid

9 standard place settings

- Bio 50°C

Arrangement upper basket Arrangement lower basket

UI51

US65

32

Technical data

This appliance complies with the following E.E.C. Directives:

- 73/23/CEE of 19/02/73 (Low Voltage Directive) and subsequent
modifications;

- 89/336/CEE of 03/05/89 (Electromagnetic Compatibility Directive) and
subsequent modifications.

Technical specifications

Dimensions

Electrical connection
Motor rating during wash
Power of heating element
Overall power

Water supply pressure

Capacity

Width 44,6 cm
Height 81,8 - 87,8 cm
Max depth 55 cm
Max depth with open door 111,4 cm

220/240 V - 50 Hz

200 W

2100 W

2300 W

Minimum 50 kPa (0.5 bar)
Maximum 800 kPa (8 bar)

9 place settings

33

Installation and connection instructions

Attention!
Carefully follow the instructions on the enclosed template for building in the
dishwasher and fitting the furniture panel.

Connecting the water supply

● Your dishwasher should be connected to a cold water supply.

● Never connect your dishwasher to open hot water appliances and continuous

flow heaters!

We advise you use a cold water supply because a hot water supply is not always
efficient with very soiled crockery as it shortens the washing programmes.

Do not use, for connection, old hoses which have been used in another
appliance.

Avoid bends or kinks in the hose which could prevent or slow down the water supply.
If the machine is connected to new pipes or pipes which have not been used for a

long time, you should run the water for a few minutes before connecting the inlet
hose. This will prevent deposits of sand or rust clogging the inlet hose.

The water pressure must be within the limits given in the technical specifications.
Your dishwasher has been built in accordance with the valid regulations governing

water-consuming appliances and is equipped with safety devices which prevent used
water from flowing back into the drinking water mains.

Water outlet connection

The end of the drain hose can be connected as follows:

1. To the sink outlet siphon, securing it if necessary with a clip.

2. To a wall outlet provided with vent-hole, minimum internal diameter 4 cm.

The waste connection must be at a height of between 30 cm (minimum) and 100 cm
(maximum) from the floor.

It makes no difference which
way the drain hose faces,
either to the right or left of
the dishwasher.

Avoid bending or kinking the
hose as this could prevent or
slow down the discharge of
water.

1 2

Ø 21

Ø 18

CS13

min 4 cm

min 30 cm

max 100 cm

34

Electrical connection

If the plug that is fitted to your appliance is not suitable for the socket, it must be
cut off and the appropriate plug fitted.

Important!
The wires on the mains lead are coloured in accordance with the following
code:

Green and Yellow -Earth
Blue -Neutral
Brown -Live

Extension hoses

The necessary extension hoses can be obtained from specialist shops or from your
local Service Force Centre.

The extension hose must be no longer than 2 metres and its internal diameter must
be no smaller than the diameter of the hose provided.

Likewise the internal diameter of the couplings used for connection to the waste
outlet must be no smaller than the diameter of the drain hose.

Arrange the extension hose horizontally along the floor and allow it to rise only
where it is to be connected to the drain.

Water protection system

To protect your dishwasher from water damage, it is equipped with a water
protection system.

In all cases of malfunction a fault code will appear on the control panel.
The fault is recognised by the fact that the indicator light of programme "Normal
65°" will start flashing, in this case turn off the water tap and call the Service Force
Centre.

Ø 18

Ø 21

+ 2 m max

CS10

max 100 cm

min 30 cm

max 100 cm

35

If you fit your own plug, the colours of the wires in the mains lead of your appliance
may not correspond with the markings identifying the terminals in your plug.

Proceed as follows:

1. Connect the Green and Yellow (earth) wire to the terminal in the plug which is

marked with the letter "E" or the earth symbol or coloured green and yellow.

2. Connect the Blue (neutral) wire to the terminal in the plug which is marked with
the letter "N" or coloured black.

3. Connect the Brown (live) wire to the terminal in the plug which is marked with
the letter "L" or coloured red.

The plug moulded onto the lead incorporates a 13amp BSI362 fuse. Only ASTA or BSI
fuses should be used.

The plug must not be used if the fuse cover/carrier is lost. The cover/carrier is
indicated by the coloured insert at the base of the product.

A replacement cover/carrier must be obtained from your local Service Force Centre.

This appliance must be earthed.
The manufacturer declines any responsibility should this safety measure
not be observed.

Warning!
A cut-off plug inserted into a 13amp socket is a serious safety (shock)
hazard. Ensure that the cut-off plug is disposed of safely.

E

13A

N

L

CE04

AEG Hausgeräte GmbH

Postfach 1036
D-90327 Nürnberg

http://www.aeg.hausgeraete.de

© Electrolux Household Appliances Limited 2002

Subject to change without notice

152985 84/2

UK

From the Electrolux Group. The world’s No.1 choice.

The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year
to a value of approx. 14 billion USD in more than 150 countries around the world.