AEG-Electrolux F88080IA User Manual

FAVORIT 88080 i

User manual Dishwasher

Dear Customer

Thank you for choosing one of our highquality products. With this appliance you will experience the perfect combination of functional design and cutting edge technology. Convince yourself that our appliances are engineered to deliver the best per formance and control  indeed we are setting the highest standards of excel lence. In addition to this you find environmental and energy saving aspects as an inte gral part of our products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfect ly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.

The following symbols are used in this user manual: Important information concerning your personal safety and information on

3 General information and tips

how to avoid damaging the appliance.

2 Environmental information

Contents

Operating Instructions 5

Safety 5

Diagram of appliance 6

Control panel 7

Switching on for the first time – setting the language 8

Display 9

Basic operation 10

An overview of the menus 10 Adjusting an option/setting 11

Prior to using for the first time 12

Setting the water softener 12 Adding special salt 14 Filling up with rinse aid 15 Setting the acoustic signal 16

In daily use 17

Loading cutlery and dishes 17 Adjusting the height of the upper basket 23 Adding detergent 24 Using 3in1 detergents 26 Selecting the dishwashing cycle (Cycle Table) 27 Starting a dishwashing cycle 29 Setting the delay start 31 Switching off the dishwasher 31

Care and cleaning 33

3Contents

What to do if … 35

Resetting the language 35 Remedying small malfunctions 35 If the dishwashing results are not satisfactory 38

Disposal 39

Technical data 39

Notes for Test Institutes 40

Contents4

Installation and connection instructions 41

Safety information for the installation 41

Installing the dishwasher 41

Connecting the dishwasher 42

Guarantee/Customer Service 44

Guarantee/Customer Service 50

Service 55

Operating Instructions

1 Safety

Prior to using for the first time

• Follow the ”Instructions for installation and connection”.

Correct use

• The dishwasher is only intended for washing domestic dishes.

• Additions or modifications to the dishwasher are not permitted.

• Use only special salt, detergent and rinse aid suitable for domestic dishwash

ers.

• Do not put any solvents in the dishwasher. This could cause an explosion.

Child safety

• Keep packaging away from children. There is a risk of suffocation.

• Children often do not recognise the hazards associated with electrical appli

ances. Don’t allow children to use the dishwasher unsupervised.

• Make sure that children and pets don’t climb into the dishwasher. Could en danger life!

• Dishwasher detergents can cause chemical burns to the eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dish washer detergent manufacturer.

• The water in the dishwasher is not for drinking. Risk of chemical burns.

5Operating Instructions

General safety

• Repairs to the dishwasher are only to be carried out by qualified service engi neers.

• When the dishwasher is not being used, switch it off and shut off the water tap.

• Never unplug the appliance by pulling on the cable. Always pull the plug.

• Ensure that the door of the dishwasher is always closed when it is not being

loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.

• Never sit or stand on the open door.

• If the dishwasher is located in a room where there may be a frost, remove the

connection hose from the tap after each use of the dishwasher.

Diagram of appliance6

Diagram of appliance

Upper basket spray arm and floor spray arm

Dispenser for special salt

Water hardness dial

Dispenser for detergent

Dispenser for rinse aid

Rating plate

Filters

Interior lighting

1 This dishwasher has an internal light that turns on and off when the opening

and closing of the dishwasher’s door occurs. Internal light equipped with led lamp CLASS 1 in accordance with EN 608251: 1994 + A1:2002 + A2:2001 In case that this light has to be replaced, please contact your local Service Force Centre.

Control panel

7Control panel

ON/OFF button Direction buttons OPTION

Display

button

Button functions

ON/OFF – Switching the appliance on and off

Direction but

tons

OPTION – Changing between Programmes menu and Options menu

RESET – cancelling the cycle that is running

OK/START – in the Programmes menu: starting a selected programme

– Selecting within the menu – Selecting a value when adjusting options or settings

– while a dishwashing cycle is running: briefly changing the display’s text line

from displaying the cycle stage to displaying the dishwashing cycle

– with options and settings: cancelling the setting procedure – changing from Options menu to Programmes menu – changing from Settings submenu to Options menu

– changing from SETTINGS… (Options menu) to Settings submenu – in the Options menu: starting and finishing the setting procedure

Button

OK/START

RESET

button

Switching on for the first time – setting the language8

Switching on for the first time – setting the lan guage

1. Press the ON/OFF button. First of all HELLO appears in the display.

As soon as the dishwasher is ready for use, this is replaced by LANGUAGE ENGLISH; the word ENGLISH is flashing.

2. Using the direction buttons ( or ) select the desired language.

3. Press the OK/START button. This will have changed the display to the

desired language. CHOOSE PROGRAMME is shown in the display.

3 If you want to change the language at a later time, please see the section “Re

setting the language”.

3 You can adjust the display lighting, by changing the settings BRIGHTNESS and

CONTRAST

; see section “Basic operation”.

1. not available with all models

Display

The info status bar consists of a row of individual lamps that is divided into two sections: the left section refers to the Programmes menu, the right section to the Options menu.

• In the Programmes and Options menus you can see at what stage within a cy

cle you currently are (the relevant lamp flashes).

• While a dishwashing cycle is running, the info status bar functions as a pro

gramme progress display. You can then see at any time how many programme stages are still to take place (including the current programme stage).

The text line indicates in the Programmes menu the name of the programme selected and the estimated length of the cycle in minutes.

• In the Options menu the name of the selected option or setting is displayed

and the current value set.

• While a dishwashing cycle is running, in the text line you can see the name of

the current programme stage and the estimated time remaining for the whole dishwashing cycle. Using the OPTION button you can briefly display the name of the dishwashing cycle.

• If there is a fault, a message is displayed. The symbols in the symbol line have the following meanings:

9Display

Info status bar

Text line

Symbol line

– Option DELAY START active

– Programme selected for the hygienic cleaning of e.g. babies’ bottles

– Option 3 IN 1 active

– Loudspeaker is switched off; no acoustic signals (SOUND VOLUME setting)

Basic operation10

Basic operation

This section contains basic information regarding the use of your dishwasher. Please read this section very carefully.

An overview of the menus

Programmes menu

AUTOMATIC

30 MINUTES

70° INTENSIVE

65° NORMAL

ENERGY

50° NORMAL

45° GLASS

PREWASH

OPTION

button

Options menu

DELAY START

SETTINGS…

OK/START

LANGUAGE

WATER HARDNESS

RINSE AID

SOUND VOLUME

BRIGHTNESS

CONTRAST

1. not available with all models

3IN1

button

The Programmes menu

• After switching on the dishwasher you will find yourself in the Programmes

menu.

• Select your dishwashing cycle here using the direction buttons ( or ). In

the info status bar your position within the menu is always shown.

• Change to the Options menu using the OPTION button.

11Basic operation

The Options menu

• Here go to the desired setting using the direction buttons ( or ). In the

info status bar your position within the menu is always shown.

• For the option DELAY START see the section “Setting a delay start” for the op

tion 3 IN 1 see the section “Before using for the first time”

• Use the OK/START button to switch from the menu item SETTINGS… to the

Settings submenu.

The Settings submenu

Here go to the desired setting using the direction buttons ( or ). In the info status bar your position within the submenu is always shown.

• LANGUAGE

To set the language of the text line in the display; also see the section “Reset ting the language”.

• WATER HARDNESS

To set the value for water hardness electronically (value range 1 to 10).

• RINSE AID

When option 3 IN 1 is activated: Switch rinseaid addition function on or off. When option 3 IN 1 is not activated: The rinseaid addition function is always switched on, even if OFF is selected for RINSEAID.

• SOUND VOLUME

To set the sound volume of the acoustic signals (value range 0 to 5); at 0 the acoustic signals are switched off.

• BRIGHTNESS

To set the brightness of the display (value range 1 to 10).

• CONTRAST

To set the contrast of the display (value range 1 to 10).

Adjusting an option/setting

1. Go to the option or setting that you wish to adjust.

2. Press the OK/START button. The value that is currently set will flash.

3. Using the direction buttons ( or ) select the desired value.

4. Press the OK/START button. The newly set value is lit without flashing.

5. Using the direction buttons ( or ) you can select another option or setting.

3 A selected value is accepted using the OPTION button. In the display the first en

try in either the Options or Settings menu is displayed.

3 You can abort the setting procedure using the RESET button.

1. not available with all models

Prior to using for the first time12

Prior to using for the first time

If you wish to use 3 in 1 detergent: – First read the section “Using 3in1 detergents”. – Do not fill up with special salt or rinse aid.

If you do not use 3in1 detergent, before using for the first time

1. Set the water softener

2. Fill up with special salt for water softeners

3. Fill up with rinse aid

Setting the water softener

The water softener must be set manually and electronically:

3 To avoid scale deposits on the dishes and in the dishwasher, the dishes must be

washed with soft water, i.e. water with a low lime content. The water softener must be set according to the table to the water hardness in the area where you live. Your local water company will be able to give you information about the water hardness in your area.

The dishwasher must be switched off.

Setting manually:

1. Open the dishwasher door.

2. Remove the lower basket from the

dishwasher.

3. Turn water hardness dial on the left wall of the dishwasher interior to 1 or 2 (see table).

13Prior to using for the first time

Setting electronically:

1. Press the ON/OFF button.

3 If the name of a programme stage is displayed in the display, a dishwashing cy

cle is active. First of all you must abort the dishwashing cycle:

– Press the RESET button. CONFIRM CANCEL? appears in the display. – Press the OK/START button. This cancels the dishwashing cycle.

2. Go to the WATER HARDNESS setting; see section “Adapting an option/setting”.

3. Set WATER HARDNESS to the right setting.

If the water softener is set electronically to “1” this switches off the display of the REFILL SALT message.

Water hardness Adjusting the hardness setting

in °d

51  70 43  50 37  42 29  36 23  28

19  22 15  18

11  1 4 1,9  2,5 II 3

4  10 0,7  1,8 I/II 2

below 4 below 0.7 I

1) (°d) German degree, measure of the hardness of water

2) [mmol/l] millimol per litre, international unit for water hardness

3) On this setting the length of the dishwashing cycle may be slightly longer. *) factory setting

in mmol/l

9,0  12,5

7,6  8,9 6,5  7,5 5,1  6,4 4,0  5,0

3,3  3,9 2,6  3,2

Range Manual Electronic

III

8 7 6

no salt necessary

Prior to using for the first time14

Adding special salt

To decalcify the water softener, it must be filled up with special salt. Use only special salt suitable for domestic dishwashers.

If you do not use 3 in1 detergent, fill up with special salt:

– Before using the dishwasher for the first time. – If when starting a cycle the message REFILL SALT is displayed.

1. Open the door and remove the lower basket.

2. Screw open the lid on the salt dispenser by turning it anticlockwise.

3. Only when using the dishwasher for the first time:

Fill the salt dispenser with water.

4. Place the funnel (supplied) over the dis penser opening. Fill the dispenser with special salt; the ca pacity of the dispenser is approx. 1.01.5 kg, depending on the size of the grains. Do not overfill the dispenser.

3 If water overflows when filling up with special salt, this is completely harmless.

5. Clean away any salt remnants from the dispenser opening.

6. Screw the lid back on in a clockwise direction.

7. Run a dishwashing cycle after filling the salt dispenser with special salt.

This will wash away salt water and salt crystals that have been spilt.

3 Depending on the size of the grains, it can take several hours for the salt to dis

solve in the water and for the message REFILL SALT not to be displayed when starting a dishwashing cycle.

Filling up with rinse aid

With rinse aid the rinsing water drains away better and so you get smearfree, gleaming dishes and clear glasses.

If you do not use 3in1 detergent, fill up with rinse aid:

– Before using the dishwasher for the first time. – If when starting a dishwashing cycle the message REFILL RINSE AID is dis

played.

Use only special rinse aid for dishwashers and no other liquid detergents.

1. Open the door. The rinse aid compartment is located on the inside of the dishwasher door.

2. Press the release button on the rinse aid compartment.

3. Open the cover.

15Prior to using for the first time

4. Pour rinse aid in slowly right up to the bro ken “max” line; this corresponds to a volume of approx. 140 ml when full.

5. Press the lid shut until it clicks into place.

6. Wipe up any spilt rinse aid with a cloth.

Otherwise there will be too much foam when rinsing.

Prior to using for the first time16

Setting the amount of rinse aid required

3 Only change the amount dispensed, if smears, milky spots (reduce the amount)

or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 16. The dosage is preset to “4” in the factory.

1. Open the dishwasher door.

2. Press the release button on the rinse aid

compartment.

3. Open the cover.

4. Set the dosage level.

5. Press the lid shut until it clicks into place.

6. If rinse aid has leaked out, wipe it away

with a cloth.

Setting the acoustic signal

In addition to the optical display (e.g. indicating the end of the cycle, errors) you can also choose to set an acoustic signal.

1. Press the ON/OFF button.

3 If the name of a programme stage is displayed in the display, a dishwashing cy

cle is active. First of all you must abort the dishwashing cycle:

– Press the RESET button. CONFIRM CANCEL? appears in the display. – Press the OK/START button. This cancels the dishwashing cycle.

2. Go to the SOUND VOLUME setting; see the section “Adapting an option/setting”.

3. Set the value for the sound volume.

You can set a value from 0 to 5. At 5 the acoustic signals are very loud, at 0 no acoustic signals are emitted; in addition the symbol is lit in the display.

17In daily use

In daily use

Loading cutlery and dishes

1 Sponges, cleaning cloths and any other objects that can absorb water must not

be washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.

For washing in the dishwasher, the following cutlery/dishes/pots and pans

are not suitable: are of limited suitability:

• Cutlery with wooden, horn, china or mother of pearl handles

• Plastic items that are not heat re sistant

• Older cutlery with cement that is sensitive to temperature

• Dishes or cutlery with glued parts

• Pewter or copper items

• Lead crystal glass

• Steel items that rust

• Wooden boards/platters

• Items made from synthetic materials

• Before loading the dishes, you should: – Remove the worst of the food residues.

– Soak pans with burnton food residues.

• When loading the dishes and cutlery, please note: – Dishes and cutlery must not impede the rotation of the spray arms.

– Load bowls, cups, glasses, pans, etc. with the opening downwards so that

water cannot collect in them

– Dishes and items of cutlery must not lie inside one another or cover one an

other

– To avoid damage to glasses, they must not touch one another – Don’t put small items (e.g. lids) in the baskets for the dishes, but in the cut

lery basket, so that they can’t fall through the holes.

• Only wash stoneware in the dishwasher if it is spe cifically marked by the manufacturer as being dish washersafe.

• Glazed patterns may fade if washed very frequently in the dishwasher.

• Silver and aluminium parts have a tendency to dis colour during washing. Food remains, e.g. egg white, egg yolk and mustard often cause discoloration and staining on silver. Therefore always clean food resi dues from silver immediately, if it is not to be washed straight after use.

• Glass can become dull after a large number of wash es.

+ 39 hidden pages