AEG-Electrolux F64570VI, F64570V User Manual

FAVORIT 64570 Vi
The fully integratable dishwasher
User information
Dear customer,
Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appli­ance.
The following symbols are used in the text:
1 Safety instructions
Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance.
3 Useful tips and hints
2 Environmental information
2
Contents
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Diagram of appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Prior to using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting the water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Adding special salt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Filling up with rinse aid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Activating/deactivating the acoustic signal . . . . . . . . . . . . . . . . . . . . . . . . . . 13
In daily use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Loading cutlery and dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjusting the height of the upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adding detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using 3in1 detergents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Selecting the dishwashing cycle (Cycle Table) . . . . . . . . . . . . . . . . . . . . . . . . 23
Starting a dishwashing cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setting the Delay Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Switching off the dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
What to do if.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Remedying small malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
If the dishwashing results are not satisfactory. . . . . . . . . . . . . . . . . . . . . . . . 32
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Notes for Test Institutes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3
Installation and connection instructions. . . . . . . . . . . . . . . . . 36
Safety information for the installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connecting to the water supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Installing and fitting the hinged door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Connection to the electrical supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Guarantee Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Customer Service Centres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4
Operating Instructions
1 Safety
Prior to using for the first time
Follow the ”Instructions for installation and connection”.
Correct use
The dishwasher is only intended for washing domestic dishes.
Additions or modifications to the dishwasher are not permitted.
Use only special salt, detergent and rinse aid suitable for domestic
dishwashers.
Do not put any solvents in the dishwasher. This could cause an explo­sion.
Child safety
Keep packaging away from children. There is a risk of suffocation.
Children often do not recognise the hazards associated with electrical
appliances. Don’t allow children to use the dishwasher unsupervised.
Make sure that children and pets don’t climb into the dishwasher. Could endanger life!
Dishwasher detergents can cause chemical burns to the eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer.
The water in the dishwasher is not for drinking. Risk of chemical burns.
General safety
Repairs to the dishwasher are only to be carried out by qualified serv­ice engineers.
When the dishwasher is not being used, switch it off and shut off the water tap.
Never unplug the appliance by pulling on the cable. Always pull the plug.
Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.
Never sit or stand on the open door.
If the dishwasher is located in a room where there may be a frost, re-
move the connection hose from the tap after each use of the dish­washer.
5
Diagram of appliance
Ceiling spray arm
Upper basket spray arm and floor spray arm
Filters
Dispenser for detergent
Dispenser for rinse aid
Control panel
Rating plate
Control panel
To use the appliance, always open the dishwasher door first.
ON/OFF button
The ON/OFF button is used to turn the dishwasher on and off.
6
Dispenser
for special salt
Set delay
timer
12 3
Programme buttons
Select 3 in1 function
Multi-display
Function buttons
The Programme buttons are used to select the desired dishwashing cy­cle.
Function buttons: In addition to the pre-set dishwashing cycle, the following functions can also be set using these buttons:
Function button 1 Sets the water softener
Function button
Function button 3 Activates/deactivates the acoustic signal
Activates/deactivates rinse aid inflow when
3in1 on
The multi-display can indicate:
the level of hardness to which the water softener is set.whether the rinse aid inflow has been activated/deactivated.whether the acoustic signal has been activated/deactivated.the start delay that has been set.the estimated time remaining for the current dishwashing cycle.what type of error has occurred with the dishwasher.
The control indicators have the following meanings:
Control indicators
1)
1)
1) These control indicators are never illuminated while a dishwashing cycle is running.
Refill with special salt
Refill with rinse aid
7
Prior to using for the first time
If you wish to use 3 in 1 detergent:
3
– First read the section “Using 3in1 detergents”. – Do not fill up with special salt or rinse aid.
If you do not use 3in1 detergent, before using for the first time
1. Set the water softener
2. Fill up with special salt for water softeners
3. Fill up with rinse aid
Setting the water softener
3 To avoid scale deposits on the dishes and in the dishwasher, the dishes
must be washed with soft water, i.e. water with a low lime content. The water softener must be set according to the table to the water hard­ness in the area where you live. Your local water company will be able to give you information about the water hardness in your area.
1. Press the ON/OFF button.
3 If the only LED indicator illuminated belongs to a programme button,
this means that this dishwashing cycle has been activated. The dish­washing cycle must be deselected: Press function buttons 2 and 3 simultaneously for approx. 2 seconds. Two lines are displayed in the multi-function display.
2. Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators for function buttons 1 to 3 will flash.
8
3. Press function button 1. The LED indicator for function button 1 will flash. The multi-display will indicate the hardness setting.
4. Pressing function button 1 increases the hardness setting by 1. (Exception: hardness setting 1 follows hardness setting 10).
5. When the hardness setting is correct, press the ON/OFF button. The hardness setting is now saved.
If the water softener is set electronically to “1”, this switches off the control indicator for special salt.
Water hardness
1)
in °d
51 - 70 43 - 50 37 - 42 29 - 36 23 - 28
19 - 22 15 - 18
11 - 1 4 1,9 - 2,5 II 3 3L
4 - 10 0,7 - 1,8 I/II 2 2L
below 4 below 0.7 I
1) (°d) German degree, measure of the hardness of water
2) [mmol/l] millimol per litre, international unit for water hardness
3) On this setting the length of the dishwashing cycle may be slightly longer. *) factory setting
in mmol/l
9,0 - 12,5
7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0
3,3 - 3,9 2,6 - 3,2
2)
Range
IV
III
Adjusting the
hardness setting
3)
10
9 8 7 6
5*
4
1
no salt necessary
Indication on the
multi-display
10L .
9L 8L 7L 6L
5L 4L
1L
9
Adding special salt
To decalcify the water softener, it must be filled up with special salt. Use only special salt suitable for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with special salt:
Before using the dishwasher for the first time.When the control indicator for special salt is illuminated on the con-
trol panel.
1. Open the door and remove the low­er basket.
2. Screw open the lid on the salt dis­penser by turning it anti-clockwise.
3. Only when using the dishwasher for the first time:
Fill the salt dispenser with water.
4. Fill the dispenser with special salt; the capacity of the dispenser is ap­prox. 1.0-1.5 kg, depending on the size of the grains. Do not overfill the dispenser.
3 If water overflows when filling up with special salt, this is completely
harmless.
5. Clean away any salt remnants from the dispenser opening.
6. Screw the lid back on in a clockwise direction.
7. Run a dishwashing cycle after filling the salt dispenser with special salt. This will wash away salt water and salt crystals that have been
spilt.
3 Depending on the size of the salt grains, it can take several hours for
the salt to dissolve in the water and for the control indicator for special salt to go out.
10
Filling up with rinse aid
With rinse aid the rinsing water drains away better and so you get smear-free, gleaming dishes and clear glasses.
If you do not use 3in1 detergent, fill up with rinse aid:
Before using the dishwasher for the first time.When the control indicator for rinse aid is illuminated on the control
panel.
Use only special rinse aid for dish­washers and no other liquid deter­gents.
1. Open the door. The rinse aid compartment is locat­ed on the inside of the dishwasher door.
2. Press the release button on the rinse aid compartment.
3. Open the cover.
4. Pour rinse aid in slowly right up to
the broken “max” line; this corresponds to a volume of ap­prox. 140 ml when full.
5. Press the lid shut until it clicks into place.
6. Wipe up any spilt rinse aid with a cloth. Otherwise there will be too much foam when rinsing.
11
Setting the amount of rinse aid required
3 Only change the amount dispensed, if smears, milky spots (reduce the
amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfac­tory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in the factory.
1. Open the dishwasher door.
2. Press the release button on the rinse
aid compartment.
3. Open the cover.
4. Set the dosage level.
5. Press the lid shut until it clicks into
place.
6. If rinse aid has leaked out, wipe it away with a cloth.
Activating/deactivating the inflow of rinse aid
If the 3 in1 button is pressed, you do not need to deactivate the inflow of rinse aid.
1. Press the ON/OFF button.
3 If the only LED indicator illuminated belongs to a programme button,
this means that this dishwashing cycle has been activated. The dish­washing cycle must be deselected: Press function buttons 2 and 3 simultaneously for approx. 2 seconds. Two lines are displayed in the multi-function display.
2. Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 2. The LED indicator for function button 2 will flash. The multi-display will indicate the current setting:
0d Inflow of rinse aid is deactivated
1d Inflow of rinse aid is activated (factory setting)
4. Pressing function button 2 activates and deactivates the rinse aid dis­pensing function.
5. Once the multi-display is indicating the required setting, press the ON/ OFF button. The setting is now saved.
12
Activating/deactivating the acoustic signal
In addition to the optical display (e.g. indicating the end of the cycle, errors) you can also choose to set an acoustic signal.
1. Press the ON/OFF button.
3 If the only LED indicator illuminated belongs to a programme button,
this means that this dishwashing cycle has been activated. The dish­washing cycle must be deselected: Press function buttons 2 and 3 simultaneously for approx. 2 seconds. Two lines are displayed in the multi-function display.
2. Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 3. The LED indicator for function button 3 will flash. The multi-display will indicate the current setting:
0b Acoustic signal deactivated
1b Acoustic signal activated (ex-factory setting)
4. Pressing function button 3 will change the setting.
5. Once the multi-display is indicating the required setting, press the ON/
OFF button. The setting is now saved.
13
In daily use
Loading cutlery and dishes
1 Sponges, cleaning cloths and any other objects that can absorb water
must not be washed in the dishwasher. Plastic and Teflon-coated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable: are of limited suitability:
Cutlery with wooden, horn, china or mother of pearl han­dles
Plastic items that are not heat resistant
Older cutlery with cement that is sensitive to temperature
Dishes or cutlery with glued parts
Pewter or copper items
Lead crystal glass
Steel items that rust
Wooden boards/platters
Items made from synthetic ma-
terials
Only wash stoneware in the dishwasher if it is specifically marked by the manufacturer as being dishwasher-safe.
Glazed patterns may fade if washed very fre­quently in the dishwasher.
Silver and aluminium parts have a tendency to discolour during washing. Food remains, e.g. egg white, egg yolk and mustard often cause discoloration and staining on silver. Therefore always clean food residues from silver immedi­ately, if it is not to be washed straight after use.
Glass can become dull after a large number of washes.
Before loading the dishes, you should:Remove the worst of the food residues.
Soak pans with burnt-on food residues.
When loading the dishes and cutlery, please note:Dishes and cutlery must not impede the rotation of the spray arms.
Load bowls, cups, glasses, pans, etc. with the opening downwards so
that water cannot collect in them
– Dishes and items of cutlery must not lie inside one another or cover
one another
To avoid damage to glasses, they must not touch one anotherDon’t put small items (e.g. lids) in the baskets for the dishes, but in
the cutlery basket, so that they can’t fall through the holes.
14
Loading cutlery
1 Warning: Sharp knives and other items of cutlery with sharp edges
must be laid in the cutlery rack or in the upper basket to avoid the risk of injury.
To ensure that all items of cutlery in the cutlery basket can be reached by the water, you should:
1.Place the grid insert on the cut­lery basket
For larger utensils, such as whisks, leave off one half of the cutlery grid.
2.Place forks and spoons in the cutlery basket's grid insert with their handles pointing down­wards.
The cutlery basket consists of two parts that can be taken apart.
1. To separate, push them horizontally in opposite directions and pull apart.
2. To put together, do this in reverse.
15
Pots, Pans, Large Plates
Load large and heavily soiled dishes in the lower basket.
The plate rack running right to left at the front right-hand side is most suitable for small flat plates with a diameter of 170-210 mm.
A serving plate can be placed in front of the cutlery basket.
To make it easier to load larger dishes, all rear plate rests in the lower basket can be folded down.
Folding down the right plate rest makes a second plate rest that is particularly suitable for deep plates or bowls.
1. Lift the two plate racks slightly at the back and fold them simultane­ously inwards making them cross over one another.
The left plate rest can be folded down and the width can be adjusted.
1. To fold them down, lift the two plate racks slightly at the back and fold them inwards making them cross over one another.
2. To set the width, pull the right-hand plate rest upwards at the back until it disengages, then pull it towards the back out of the front guide.
3. Insert the plate rest in the other guide and press it down at the back until it snaps in.
16
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long, sharp cutlery in the upper bas­ket.
Adjustable cup racks
Arrange items of crockery on and
under the folding cup racks so that they are offset from each other and water can reach all items.
The cup racks can be folded up
out of the way for tall crockery items.
The cup racks can also be fixed in
an intermediate position. Lay or hang glasses with stems in the slots in the cup racks.
17
Glass holders
For glasses with stems and tall cy­lindrical glasses, fold up the glass holder. ( Top picture)
To unload or when not needed, fold the glass holders back to the right. (Middle picture)
Glasses can also be placed over the bars pointing up. (Bottom picture)
18
Adjusting the height of the upper basket
Maximum height of dishes in the
Upper basket Lower basket
with upper basket raised 19 cm 32 cm
with upper basket lowered 21 cm 30 cm
3 The height of the baskets can also be adjusted when they are loaded.
Raising/lowering the upper basket
1. Pull out the upper basket complete-
ly.
2. Raise the upper basket as far as it will go and then lower it vertically. The upper basket will latch into the lower or the upper position.
Maximum plate sizes, upper basket in upper position
Maximum plate sizes, upper basket in lower position
19
Adding detergent
Detergents remove the dirt from dishes and cutlery. The detergent must be added before the cycle starts.
1 Only use detergent intended for do-
mestic dishwashers. The detergent compartment is lo-
cated on the inside of the door.
1. If the lid is closed: Press the release button. The lid will spring open.
2. Place the detergent in the detergent dispenser. The markings indicate the dosing levels for powder detergents: “20/30” corresponds to approx. 20/30 ml of detergent. Follow the manufacturer’s instruc­tions with regard to dosing and storage.
3. Close the lid and press until it locks into place.
3 In the case of very heavily soiled
dishes, fill the adjoining compart­ment (1) with additional detergent. This detergent comes into use during the pre-wash cycle.
20
Concentrated detergents
Today’s detergents for dishwashers are almost exclusively low-alkaline concentrated detergents with natural enzymes in tablet or powder form.
2 Using 50°C dishwashing cycles in conjunction with these concentrated
detergents reduces pollution and is good for your dishes, as these dish­washing cycles are specially matched to the dirt-dissolving properties of the enzymes in concentrated detergents. It is for this reason that us­ing 50 °C dishwashing cycles in conjunction with concentrated deter­gents can achieve the same cleaning results that can otherwise only be achieved using 65 °C cycles.
Detergent tablets
3 Detergent tablets from different manufacturers dissolve at different
rates. For this reason, some detergent tablets do not attain their full cleaning power during short cycles. Therefore please use dishwashing cycles with pre-wash when using detergent tablets.
21
Using 3in1 detergents
These products are detergents with a combined cleaning, rinsing and salt function.
When the 3in1 function is activated, – the addition of special salt and rinse aid from the respective dispenser
is prevented.
If the salt and rinse aid dispensers are empty, this is not indicated. The dishwashing cycles can be up to 30 minutes longer.
3 If you want to use 3in1 detergents, check whether these detergents are
suitable for your water hardness. (Follow the manufacturer’s instruc­tions.)
If you want to use 3in1 products
1. Press the ON/OFF button.
2. Press the 3IN1 button.
The button indicator lights up: 3in1 function is selected. Before the start of the dishwashing cycle put 3in1 detergent in the de-
tergent dispenser.
3 As the rinse aid inflow is automatically switched off when the 3in1
function is activated, it may come about because of the different qual­ity standards in the 3in1 detergent, that the dishes do not dry suffi­ciently. If this happens, proceed as follows (see section “Adding rinse aid”):
Fill up the dispenser (if this is empty) with rinse aid.
Set rinse aid dosage to “2” mechanically.
Activate rinse aid inflow.
22
If you do not want to use 3in1 products any more
If you want to stop using 3in1 products, please do the following:
Deactivate the 3in1 function.
Fill up the dispensers for salt and rinse aid again.
Switch the water softener to the highest setting and perform up to
three normal cycles without loading any dishes.
Then set the water softener to the water hardness in your area.
If you want to use 4in1 products
When using "4 in 1" detergents that integrate also anti- glass corrosion agent into "3 in 1" formula, please follow the same indication as given for "3 in 1" detergents.
Selecting the dishwashing cycle (Cycle Table)
Dishwashing-
cycle
AUTOMATIC (50° - 65°)
30 MIN.
3)
(60°)
Suitable
Dinner service
2)
and cookware
Dishes, excluding saucepans
for:
Type of
soiling
normally soiled, dried-on food re­mains
just used, lightly to normally soiled
Programme
sequence
Pre-wash
Main wash
Intermediate rinse
1 to 2x
- - -
Final rinse
Consumption
values
Drying
Length (minutes)
Energy (kWh)
90 - 115
1,0 - 1,5
30
0,8
1)
heavily soiled,
INTENSIVE
CARE 70°
Dinner service and cookware
dried-on food re­mains, in particular protein and starch
2x
110 - 120
1,75 - 1,95
Dinner service and cookware,
ECO 50°
4)
temperature-sen­sitive crockery
normally soiled • • • • •
130 - 160
0,95 - 1,05
1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are. Variations are therefore possible in practice.
2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and water and energy consumption can vary greatly – depend­ing upon the load and how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C.
3) When using this cycle, only load the dishwasher half full.
4) Test programme for Test Institutes
Water (litres)
12 - 22
8
22 - 24
12 - 14
23
Selecting a programme
When your dishes look like this, select: an intensive programme.
a normal or energy-saving pro­gramme.
24
a short programme (e.g. 30 minute programme).
Starting a dishwashing cycle
1. Check that the spray arms can turn freely.
2. Turn the water tap on fully.
3. Press the ON/OFF button.
4. Select the desired programme.
The programme indicator will illuminate.
5. Close the door. The wash programme will begin.
Interrupting or aborting a dishwashing cycle
Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary.
Interrupting the dishwashing programme by opening the dishwash­er door
1 Hot steam may escape when the door is opened. There is a risk of scald-
ing.
1. Open the door carefully. The dishwashing cycle will stop.
2. Close the door. The cycle will continue.
Aborting the dishwashing cycle
1. Press function buttons 2 and 3 and keep them pressed.
Two lines are displayed in the multi-display.
2. Release the function buttons. The dishwashing cycle has been can­celled.
3. If you want to start a new cycle, check whether there is any detergent in the dispenser.
Setting the Delay Timer
3 With the delay timer you can delay the start of a dishwashing cycle for
between 1 and 19 hours.
1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example, 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is lit.
2. Select dishwashing cycle.
3. The time remaining until the start of the cycle is continuously displayed
(e. g., 12h, 11h, 10h, … 1h etc.).
4. Close the door.
25
To change the delay timer:
As long as the cycle has not yet started, you can still change the setting by pressing the Delay Timer button after opening the door.
Cancelling the time delay:
Press the Delay Timer button repeatedly until the length of the selected cycle appears in the multi-display. The selected dishwashing cycle will begin immediately.
To change a dishwashing cycle
As long as the cycle has not yet started, you can still change the dish­washing cycle. First abort the dishwashing cycle, then re-set the time delay, lastly select the new dishwashing cycle.
Switching off the dishwasher
If the acoustic signal has been enabled, a continuous tone will sound for approx. 15 seconds at the end of the dishwashing cycle.
1 Carefully open the door. Hot steam may escape.
Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about 15 minutes before removing them. You also get a better drying result.
1. Press the ON/OFF button. All display indicators will go out.
2. Turn off the water tap.
3 If the dishwasher is not switched off, then the acoustic signal is repeat-
ed after 3 minutes and after 6 minutes.
Removing the dishes
3 It is normal for the inner door and the dispensers to be damp.
Empty the lower basket first, then the upper basket. This way you
avoid dripping water from the upper basket onto dishes in the lower basket.
26
Care and cleaning
Do not use furniture care products or aggressive cleaners.
1
When necessary, clean the dishwasher’s controls with a soft cloth and
clean warm water.
Occasionally check the internal dispensers, door seal and water inlet
filter (if fitted) for dirt and clean them, if necessary.
Polished chromium steel surfaces
Remove light dirt with a clean, damp, soft cloth – microfibre cloths are particularly good.
1 When cleaning ensure that you do not go against the direction of the
stainless steel finish (the fine horizontal lines).
No circular movements!
Alulook surfaces
Remove light dirt with a clean, damp, soft cloth – microfibre cloths are particularly good. Agents that scratch or scour are not suitable. If required, use a commercially available cleaner for chrome surfaces. Follow the manufacturer’s instructions when using this cleaner.
27
Cleaning the filters
3 The filters must be regularly checked
and cleaned. Dirty filters will affect the dishwashing results.
Coarse filter (1)
The coarse filter must be checked after every dishwashing cycle.
1. Open the door and remove the lower basket.
2. Remove the coarse filter.
3. If necessary, rinse under running water and replace.
Fine filter (2)
The fine filter must be cleaned occa­sionally.
1. Open the door and remove the lower basket.
2. Release the fine filter by turning to the right and remove.
3. Clean the fine filter thoroughly with a brush under running water.
4. Place the fine filter in the holder and turn to the left until you feel it click into place (arrow).
1 Do not press the handle downwards.
If the filter does not click into place, this can lead to the spray arm nozzles becoming blocked. Under no circumstances may the dishwasher be used without its filters.
28
Cleaning the spray arms
Regularly check the nozzles in the three spray arms for blockages. If necessary, clean the nozzles with a piece of fine wire or a fine needle and a strong water jet.
1 Do not damage the nozzle openings.
Top spray arm
1. Undo the fixing screw (A) by turning
anti-clockwise.
2. Pull the spray arm off the shaft.
3. Clean the spray arm and the fixing
screw.
4. Fasten the spray arm with the fixing screw (A) turning clockwise.
Middle spray arm
1. Remove the middle spray arm by
turning it laterally. The two-part spray arm bearing is held together by a tension spring (B)
2. Clean spray arm nozzles.
3. To re-fit, press the middle spray arm
upwards until you feel it snap into place.
Lower spray arm
1. Undo the fixing screw (C) by turning
anti-clockwise.
2. Pull the spray arm off the shaft.
3. Clean the spray arm and the fixing
screw.
4. Fasten the spray arm with the fixing screw (C) turning clockwise.
29
What to do if...
Remedying small malfunctions
If the acoustic signal is activated, warning tones sound if there are faults. If one of the following fault codes is displayed in the multi-display dur­ing operation:
Fault codeÅ10 (Problems with water inlet),Fault codeÅ20 (Problems with water drainage),
please have a look at the following table. When the fault is remedied, press the button for the cycle that has
started. The cycle will continue. With other fault codes (“Å ” followed by a number):
Abort the dishwashing cycle. Switch the appliance off and on again. Re-set the dishwashing cycle.
If the fault is displayed again, please contact the Customer Care De­partment and inform them of the fault code.
Malfunction Possible cause Remedy
30
1 short warning tone continuously repeated can be heard, the cycle indicator for the selected dishwashing cycle is flashing: fault code played in the multi-dis­play: (Problems with water in­let)
Å10 is dis-
Water tap is blocked with limescale or faulty.
The tap is turned off. Turn the tap on.
The filter (where present) in the threaded hose fitting on the tap is blocked.
Filters in the base of the dishwasher compartment are blocked.
Water inlet hose has not been correctly posi­tioned.
Check the water tap and have it repaired if necessary.
Clean the filter in the threaded hose fitting.
Cancel the dishwashing cy­cle (see chapter: Starting a dishwashing cycle), clean filters (see chapter: Cleaning the filters), then start the dishwashing cycle again.
Check the position of the hose.
Malfunction Possible cause Remedy
2 short warning tones
The sink outlet is blocked. Clean out sink outlet. continuously repeated can be heard. The cycle indicator for the selected dishwashing cycle is flashing, fault code
Å20 is dis-
played in the multi-dis-
Water drain hose
has not been correctly posi-
tioned.
Check the position of the hose.
play. (Problems with water outflow)
3 short warning tones continuously repeated can be heard, Fault code
Å30 is dis-
played in the multi-dis-
The anti-flood system has
been triggered.
First shut off the water tap, then switch off the appli­ance and contact the Cus­tomer Care Department.
play.
The cycle is not starting.
The mains plug is not
plugged in.
A fuse in the house’s wiring
system is defective.
For dishwasher models with
a delay start timer:
A start time has been se-
lected.
Plug in mains plug.
Replace fuse.
If the dishes are to be washed immediately, cancel the delay start.
The dishwashing compart-
ment is made from rust-
free stainless steel. Rust
spots in the dishwashing
Rust spots are visible in the dishwashing compart­ment.
compartment are due to
rust particles from external
sources (rust particles from
water pipes, pans, cutlery,
Only wash cutlery, dishes and pans that are suitable for dishwasher use.
etc.). Remove such spots
with a commercially-avail-
able cleaning product for
stainless steel.
Decalcify appliance with commercially available
agents for cleaning dish­A whistling noise can be heard when washing dish­es.
The whistling is not a cause for concern.
washers.
If the noises can still be
heard after decalcifying the
machine, use a different
brand of detergent for
washing cutlery and dishes.
31
If the dishwashing results are not satisfactory
The dishes are still dirty.
The wrong dishwashing cycle was selected.
The dishes were loaded is such a way that the dishwashing water did
not reach all items. The baskets for the dishes must not be overload­ed.
The filters in the base of the washing compartment are dirty or incor­rectly positioned.
Good quality detergent was not used, or too little was used.
In the case of scale deposits on the dishes: The special salt dispenser is
empty or the water softening system has been incorrectly set.
The drain hose is incorrectly positioned.
Pollutants from the water in the dishwasher can block the jets in the
spray arms. You have the option of removing the spray arms from their fixture for cleaning (see section “Care and Cleaning”).
The dishes do not dry and are not shining.
Poor quality rinse aid was used.
The rinse aid dispenser is empty.
There are smears, streaks, milky spots or a shiny bluish coating on glasses and dishes.
Lower rinse aid dosage.
32
There are dried water drops on the glasses and dishes.
Increase rinse aid dosage.
The detergent may be the cause. Contact the detergent manufactur-
er's customer advice centre.
Glass corrosion
Contact the detergent manufacturer's customer advice centre.
Disposal
Packaging material
2
The packaging materials are environmentally friendly and can be recy­cled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities.
2 Old appliance
The symbol product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of elec­trical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed infor­mation about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
W on the product or on its packaging indicates that this
1 Warning! When your appliance has finished its working life, remove
the plug from the socket. Cut off the cable and plug and dispose of them. Break the door lock so that the door no longer shuts. This prevents chil­dren from trapping themselves inside and endangering their lives.
33
Technical data
Capacity: 11 place settings including serving dishes
Permitted water pres­sure:
Electrical connection: 230 V, 10 A, also see the rating plate on the right-hand side
Total output 2250 W
Dishwashers that can be integrated and built-in
Dimensions: 759 x 546 x 570 (H x W x D in mm)
Max. weight: 55.3 kg
1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa)
of the dishwasher’s interior door.
5 This appliance conforms with the following EU Directives:
73/23/EEC dated 19.02.1973 Low Voltage Directive89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
34
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the
appliance fully loaded and using the test cycle (see "Cycle Table"). Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively, and using the test cycle (see "Cycle Table").
Full load:
11 place settings incl. serving dishes
Amount of detergent required: 27.5 g in the dispenser for detergent
Rinse aid setting: 6
Measurement of noise
The measurement is to be made immediately following a completed short cycle.
Sample loading arrangements:
Upper basket * Lower basket
* Upper basket in bottom (lowered) position
Cutlery basket
1 Soup spoon 2 Knife 3 Fork
4 Dessert spoon 5 Teaspoon 6 Serving spoon
35
Installation and connection instructions
1 Safety information for the installation
Only transport the dishwasher in an upright position, otherwise salt water may run out.
Before using the dishwasher for the first time, check for any damage caused in transport. Do not under any circumstances connect an ap­pliance that is damaged. In the case of damage, please contact your supplier.
Never use the dishwasher if the mains cable, water inlet or drain hose are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible.
Always plug the mains plug into a correctly installed shockproof socket.
Permanent connection: a permanent connection must only be in­stalled by a trained electrician.
Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the sup­ply where the appliance is to be installed. The fuse rating is also to be found on the rating plate.
Multi-way plugs / connectors and extension cables must not be used. This could constitute a fire hazard through overheating.
The dishwasher’s cable must only be replaced by the Customer Care Department or a registered electrician.
A water inlet hose with safety valve must only be replaced by the Customer Care Department.
36
General
The dishwasher is supplied ready to be connected to the electrical sup­ply, i.e. with electrical cable, in­stalled drain hose and inlet hose with filter.
The dishwasher may be built into recesses made of flammable mate­rials without additional measures being taken.
It is preferable that the connection to the mains is located in the unit next to the dishwasher. It must not be directly behind the appliance.
The regulations of the local water board and electricity company must be observed.
37
Connecting to the water supply
Inlet
Water pressure: 1–10 bar (flow pressure)
The appliance can be connected to cold and hot water, maximum
temperature 65 °C.
The site must provide a regulating tap with G 3/4” outlet.
The appliance must be connected with the plastic pressure hose sup-
plied (with filter, in accordance with EN61770, 10 bar.)
Installation of an IRG filter is recommended as part of the house’s water system.
After the regulating tap is opened, no water may leak out of the con­nection fittings.
If connecting to the hot water system, the threaded joints must be checked a few minutes after the machine is first used and tightened if necessary. (Be careful not to overwind the threaded joints.)
Drainage
The flexible drain hose with an inner diameter of 22 mm is to be laid
with no kinks.
The appliance can also be installed above the level of the sink spigot. A return inhibitor is integrated into the machine’s drainage and therefore connection fittings with non-return valves are not neces­sary.
The preferred connection is via the spigot of the sink outlet in the unit next to the machine.
The highest point of the drain hose is not to be more than 500 mm above the floor of the appliance.
38
Installing and fitting the hinged door
A normal kitchen unit door with the following dimensions can be used as a hinged door:
Max width 596 mm
Max. height 720 mm
Max. depth 20 mm
Weight (including handle) 3 kg to
max. 8 kg
1 Do not exceed maximum door height,
as otherwise the door will not be able to close properly.
The hinged door must be fitted with a handle. The hinges needed for installation and the associated screws are stand-
ard parts (included in the delivery).
3 Hinged doors with special handles are also available as accessories.
These must be ordered separately:
Hinged door set in “AEG Nexxt” design: Accessory number 153 1295 00
Hinged door set in “Century” design: Accessory number 153 1296 00
3 The plinth area that can still be seen
after the hinged door has been in­stalled can either be hidden with a matching panel, or by extending the panel of the kitchen unit that is un­der the appliance.
39
Fitting the hinged door
1. Fit the two lateral bars A as shown in
the figure opposite. Align bars at the top so that the upper hole lies over the pre-mounted aligning disk. With a width of 568 mm first fix the additionally supplied aligning disks B on the already pre-mounted aligning disks.
2. Screw in the bars at the top only.
3. Stand the machine in front of the
kitchen unit into which it is to be in­stalled. Place cable and hoses into the neighbouring unit. As you push the machine in, keep on pulling the cable and hoses through and ensure that they do not become kinked.
4. Align the machine laterally in the plinth area with the angle AN, tight­en the screw V slightly.
5. Before installation of the hinge sup­port: Screw bottom unit of the hinge into the holes provided in the hinge support.
40
6. Place the hinge supports evenly spaced on the floor of the recess and align flush with the front of the floor of the recess. Fasten with the 6 wood screws supplied.
7. Using the drilling template supplied, mark out and drill two holes a (ø35 mm, 11 mm deep) for the hinges at the bottom of the hinged door. To do this, align the drilling template with the bottom edge of the hinged door.
a
8. Using the drilling template supplied, mark out and drill 8 holes b for the two guides (ø2 mm, 12 mm deep) at the top of the hinged door. To do this, align the drilling template with the top edge of the hinged door.
b
41
9. Screw the hinges using 4 countersunk head wood screws and the guides us­ing 8 Spax screws (4.0 x 20, pozidrive) to the hinged door.
10. Snap the hinges on the hinged door into the bottom units of the hinges. Hold the hinged door carefully, so that the hinges are not bent.
11. Adjust the hinges using the screws A, B and C to match the kitchen unit
(width of gap, etc.)
12. Insert the guiders into the guides.
42
13. Fix the guiders with screws to the right and the left on the appliance door.
14. Adjust the depth of the appliance, open the appliance door carefully, without changing the position found. Fix the appliance laterally at the top using wood screws.
15. Fix the appliance laterally by tighten­ing screw V. To do this, there are 2 oblong holes to the right and left in the hinge support to allow access for the screwdriver.
43
Connection to the electrical supply
Installation must be via a mains cable with a plug. The plug must be ac­cessible after the installation, or a separation device with at least a 3 mm contact gap must be provided in the permanent house wiring that gives the appliance simultaneous all-pole separation from the electrical supply.
House’s electrical system:
Install fuse, mains cable and socket in accordance with the electrical schematic.
Wiring:
Heating element voltage 230 V
44
Guarantee Conditions
Belgium
DECLARATION OF GUARANTEE TERMS. Our appliances are produced with the greatest of care. However, a defect may still occur. Our con­sumer services department will repair this upon request, either during or after the guarantee peri­od. The service life of the appliance will not, however, be reduced as a result.
This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provi­sions of the Civil Code. The statutory rights that the consumer has under this legislation are not affected by this declaration of guarantee terms. This declaration does not affect the vendor's statutory warranty to the end user. The appliance is guaranteed within the context of and in adherence with the following terms:
1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of charge any defect that occurs within 24 months from the date the appliance is delivered to the first end user. These guarantee terms do not apply in the event of use for professional or equivalent purposes.
2. Performing the guarantee means that the appliance is returned to the condition it was in before the defect occurred. Defective parts are replaced or repaired. Parts replaced free of charge become our property.
3. So as to avoid more severe damage, the defect must be brought to our attention immediately.
4. Applying the guarantee is subject to the consumer providing proof of purchase showing the pur-
chase and/or delivery date.
5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic), synthetic materials and rubber, is the result of inappropriate use.
6. The guarantee cannot be called on for minor faults that do not affect the value or the overall reli­ability of the appliance.
7. The statutory warranty does not apply when defects are caused by:
a chemical or electrochemical reaction caused by water,
abnormal environmental conditions in general,
unsuitable operating conditions,
contact with harsh substances.
8. The guarantee does not apply to defects due to transport which have occurred outside of our re­sponsibility. Nor will the guarantee cover those caused by inadequate installation or assembly, lack of maintenance or failure to respect the assembly instructions or directions for use.
9. Defects that result from repairs or measures carried out by people who are not qualified or expert or defects that result from the addition of non-original accessories or spare parts are not covered by the guarantee.
10. Appliances that are easy to transport may be delivered or sent to the consumer services depart­ment. Home repairs are only anticipated for bulky appliances or built-in appliances.
11 . If the appliances are built-in, built-under, fixed or suspended in such a way that removing and re-
placing them in the place where they are fitted takes more than half an hour, the costs that result therefrom will be charged for. Connected damage caused by these removal and replacement oper­ations will be the responsibility of the user.
12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the re­pair costs are considered disproportionate, in agreement with the consumer, the defective appli­ance may be replaced with another appliance of the same value. In this event, we reserve the right to ask for a financial contribution calculated according to the length of time it has been used.
13. A repair under guarantee does not mean that the normal guarantee period will be extended nor that a new guarantee period begins.
14. We give a twelve month guarantee for repairs, limited to the same defect.
15. Except in the event where liability is legally imposed, this declaration of guarantee terms excludes
any compensation for damage outside the appliance for which the consumer wishes to assert his rights. In the event of legally admitted liability, compensation will not exceed the purchase price paid for the appliance.
These guarantee terms are only valid for appliances purchased and used in Belgium. For exported appliances, the user must first make sure that they satisfy the technical conditions (e.g.: voltage, frequency, installation instructions, type of gas, etc.) for the country concerned and that they can
45
withstand the local climatic and environmental conditions. For appliances purchased abroad, the user must first ensure that they meet the qualifications required in Belgium. Non-essential or re­quested adjustments are not covered by the guarantee and are not possible in all cases.
Our consumer services department is always at your disposal, even after the guarantee period has expired.
Address for our consumer services department: ELECTROLUX HOME PRODUCTS BELGIUM Bergensesteenweg, 719 - 1502 LEMBEEK Tel.: 02.363.04.44
Customer Service Centres
Belgium
Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek E-mail: consumer.services@electrolux.be
Consumer services 02/363.04.44 02/363.04.00
Tel.: Fax.:
02/363.04.60
46
Service
In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instruc­tions (section “What to do if…”).
If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners.
In order to be able to assist you quickly, we require the following information:
Model descriptionProduct number (PNC)Serial number (S No.)
(for numbers see rating plate)
Type of faultAny error messages displayed by
the appliance
So that you have the necessary reference numbers from your appliance at hand, we recommend that you write them in here:
Model description: .....................................
PNC: .....................................
S No: .....................................
47
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg
http://www.aeg-electrolux.de
© Copyright by AEG
822 612 845-00-13 0906-02
Subject to change without notice
Loading...