AEG-Electrolux 99852G-M User Manual

B 99852G

User Manual

Hob

Important Safety Information

You MUST read these warnings carefully before installing or using the hob. If
you need assistance, contact our Customer Care Department on 08705 350350

Installation

z This appliance must be installed and serviced by a competent person as stated in the

Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring
Regulations.

z For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas

Installations I.S.813 Current Editions and the ETCI Rules for Electrical Installations.

z Remove all packaging before using the hob.
z Ensure that the gas and electrical supply complies with the type stated on the rating

plate, located near the gas supply pipe.

z Do not attempt to modify the hob in any way.

Child Safety

z This hob is designed to be operated by adults. Do not allow children to play near or

with the hob.

z The hob gets hot when it is in use. Children should be kept away until it has cooled.
z Children can also injure themselves by pulling pans or pots off the hob.
z This appliance is not intended for use by children or other persons whose physical,

During Use

z This hob is intended for domestic cooking only. It is not designed for commercial or

z This appliance is not connected to a combustion products evacuation device. It must

z When in use a gas cooking hob will produce heat and moisture in the room in which

z When using the hob for a long period of time, the ventilation should be improved, by

2

sensory or mental capabilities or lack of experience and knowledge prevents them
from using the appliance safely without supervision or instruction by a responsible
person to ensure that they can use the appliance safely.

industrial purposes.

be installed and connected in accordance with current installation regulations. Particular
attention shall be given to the relevant requirements regarding ventilation.

it has been installed. Ensure there is a continuous air supply , keeping air vents in
good condition or installing a cooker hood with a venting hose.

opening a window or increasing the extractor speed.

z Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.
z Ensure the control knobs are in the ‘OFF’ position when not in use.
z When using other electrical appliances, ensure the cable does not come into contact

with the hot surfaces of the cooking appliance.

z Unstable or misshapen pans should not be used on the hob as unstable pans can

cause an accident by tipping or spillage.

z Never leave the hob unattended when cooking with oil and fats.
z Never use plastic or aluminium foil dishes on the hob.
z Perishable food, plastic items and areosols may be affected by heat and should not

be stored above or below the hob unit.

Service

z This hob should only be repaired or serviced by an authorised Service Engineer and

only genuine approved spare parts should be used.

Environmental Information

U

z After installation, please dispose of the packaging with due regard to safety and the

environment.

z When disposing of an old appliance, make it unusable, by cutting off the cable.
z The symbol on the product or on its packaging indicates that this product may

not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. For more detailed information
about recycling of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.

Keep this instruction book for future reference and ensure it is passed on to any
new owner.

These instructions are only valid for countries whose identification symbols are shown
on the cover of this instruction booklet and on the appliance itself.

3

Contents

Instructions for the User

Important Safety Information 2
Description of the Hob 5
Operation 6
Maintenance and Cleaning 8
Something Not Working? 10
Service and Spare Parts 11
Customer Care 24
Guarantee Conditions 25
European Guarantee 26

Instructions for the Installer

Important safety requirements 12
Installation 13
Building In 14
Electrical connections 17
Wiring diagram 18
Fault Finding 19
Commissioning 22
Conversion from Natural Gas to LPG 23

Guide to Use the instructions

The following symbols will be found in the text to guide you throughout the Instructions:

Safety Instructions
Step by step instructions for an operation

))

)

))

Hints and Tips
Environmental Information

U

This appliance is manufactured according to the following EEC directives:
2006/95 EEC - 93/68 EEC ­89/336 EEC - 90/396 EEC, current edition.

4

Description of the Hob

1

2

3

1. Hob T op

2. Semi-rapid Burners

3. Auxiliary Burner

4. Ultra-rapid Burner (triple crown)

5. Control knobs

4

2

2

5

INSTALLATION

Any gas installation must be carried out by a competent person, and in accordance
with existing rules and regulations.

The relevant instructions are to be found in the second section of this manual.
Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the

event of a breakdown.

WHEN THE HOB IS FIRST INSTALLED

Once the hob has been installed, it is important to remove any protective materials, which
were put on in the factory .

5

Operation

Hob burners

T o light a burner:

))

)

))

z Push in the relevant control knob and turn it to

maximum position.

z Upon ignition, keep the knob pushed down about

5 seconds. This will allow the "thermocouple"
(fig. 1 - letter D) to be heated and the safety device
to be switched off, otherwise the gas supply would
be interrupted.

z Then adjust the flame as required.
z If the burner does not ignite, turn the control knob

to zero, and try again.

z If you cannot light the flame even after several

attempts, check the "cap" (lett. A) and the "crown"
(lett. B) are in the correct position.

triple crown

burner

Each control knob is equipped with a pilot light
which gradually lights up according to the heat
level that you select with the control knob.
When switching on the mains, after installation or a
power cut, it is quite normal for the spark generator
to be activated automatically.

As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid simmering.

If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the vessel, causing the handle to
overheat.

Take care when frying food in hot oil or fat,
as the overheated splashes could easily ignite.

If the control knobs become difficult to turn, please contact your local Service Force Centre.

In the absence of electricity, ignition can occur without the electrical device; in this case
approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until
it reaches the "maximum" position.

C

A - Burner cap

B - Burner crown
C - Ignition electrode
D - Thermocouple

A
B

D

6

T o ensure maximum burner efficiency , you should only use pots and pans with a flat
bottom fitting the size of the burner used (see table).

Burner minimum maximum

diameter diameter

Large (ultra-rapid) 180 mm 260 mm
Medium (semi-rapid) 120 mm 220 mm
Small (Auxiliary) 80 mm 160 mm

Using the Wok Stand

A wok stand is provided to enable you to use a
round bottomed wok on the hob. The wok stand
must only be used on the central burner, and
should not be used with any other type of wok
or pan. When fitting the wok stand, ensure the
recessesd in the frame fit securely onto the bars
of the pan supports, as shown in figure 2.

Fig. 2

7

Maintenance and Cleaning

Before any maintenance or cleaning
can be carried out, you must
DISCONNECT the hob from the
electricity supply .

The hob is best cleaned whilst it is still
warm, as spillage can be removed more
easily than if it is left to cool.

The Hob Top

Regularly wipe over the hob top using a
soft cloth well wrung out in warm water
to which a little wasing up liquid has been
added. Avoid the use of the following:

- household detergent and bleaches;

- impregnated pads unsuitable for non­stick saucepans;

- steel wool pads;

- bath/sink stain removers.
Should the hob top become heavily
soiled, the following product s are
recommended:

- for stainless steel hobs use a
proprietary stainless steel cleaner;

- for other hobs use Hob Brite or Bar
Keepers Friend.

If scratches or cracks are noticed,
disconnect the appliance from the
electrical supply and call your
nearest Service Force Centre.

YES

NO

fig. 3.

Pan Supports

To keep the pan supports in the
correct position, they are mounted
on metal pins located in the back
of the hob. After cleaning the hob,
ensure the pan supports are
properly placed as shown in fig. 3.

8

Pan Supports

T o keep the pan supports in the correct position, they are mounted on metal pins
located in the back of the hob. After cleaning the hob, ensure the pan supports are
properly placed as shown in fig. 3.
The pan supports are dishwasher proof. If washing them by hand, take care when drying
them as the enamelling process occasionally leaves rough edges. If necessary , remove
stubborn stains using a paste cleaner.

The Burners

The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy water , and remove marks with a mild
paste cleaner. A well moistened soap impregnated steel wool pad can be used with
caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry
with a soft cloth.

Ignition electrode

The electric ignition is obtained through a ceramic "electrode" and a metal electrode (fig.
1 - letter C). Keep these components well clean, to avoid difficult lighting, and check that the
burner crown holes are not obstructed.

9

Something Not Working?

If the hob is not working correctly, please carry out the following checks before contacting
your local Service Force Centre.

SYMPTOM

 There is no spark when lighting the gas

SOLUTION

 Check that the unit is plugged in and the

electrical supply is switched on

 Check that the RCCB has not tripped (if fitted)
 Check the mains fuse has not blown
 Check the burner cap and crown have been

replaced correctly, e.g. after cleaning.

 The gas ring burns unevenly

 Check the main jet is not blocked and the

burner crown is clear of food particles.

 Check the burner cap and crown have been

replaced correctly, e.g. after cleaning.

If after all these checks, your hob still does not operate correctly, contact your local
Service Force Centre.

Please note that it will be necessary to provide proof of purchase for any in­guarantee service calls.

In-guarantee customers should ensure that the above checks have been made as the
engineer will make a charge if the fault is not a mechanical or electrical breakdown.

10

Instructions for the Installer

Engineers technical data

Instructions for the Installer

Overall dimensions

Width: 880 mm
Depth: 510 mm

Cut out dimensions

Width: 830 mm
Depth: 480 mm

Supply Connections

Gas: RC 1/2 inch (1/2 inch male) Rear right

hand corner
Electric: 230 V 50 Hz supply , 3 core flexible
cable with non rewireable plug fitted with a 3
amp cartridge fuse.

Heat Input

Ultra-rapid Burner 3.8 kW Natural Gas
(Triple crown) (12,966 BTU/HR)

3.8 kW L.P.G.
(12,966 BTU/HR)

BURNER ULTRA-RAPID SEMI-RAPID AUXILIARY

TYPE OF GAS

POSITION MAX MIN MA X MIN M AX MIN

Burner Dia. Tap By-pass

1/100 mm

Auxiliary 28
Semi-rapid 32
Ultra-rapid 56

Aeration adjustment none

Semi-rapid Burner 1.9 kW (6,483 BTU/HR)
Auxiliary Burner 1.0 kW (3,412 BTU/HR)

Appliance class 3
Appliance category II2H3+
Gas supply Natural gas G 20 / 20 mbar

(triple crown) (medium) (small)

NATURAL GAS

20 mbar

VALUE =

37.78 MJ/m

Ws - 50.7 MJ/ m

LPG GAS

28-30/37 mbar

VALUE =

49.92 MJ/Kg

NOMINAL THERMAL
POWER (kW) 3.8 1.20 1 . 9 0.45 1.0 0.33

NOMINAL FLOW
RATE (m3/h) 0.362 0.114 0.181 0.043 0.095 0.028

3

3

NOZZLE REFERENCE 146 Adjust. 96 Adjust. 70 Adjust.

(1/100 mm)

NOMINAL THERMAL
POWER (kW) 3.8 1.20 1 . 9 0.45 1.0 0.33

NOMINAL FLOW
RATE (g/h) 274 86 137 32.4 72 23.8

NOZZLE REFERENCE 98 40 71 32 50 28
(1/100 mm)

11

Instructions for the Installer

Important safety requirements

This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations
(Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the
Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the
ETCI Rules for Electrical Installations. Detailed recommendations are contained in the following
British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.

Provision for ventilation

The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed
in a room of volume less than 5 m
in a room of volume between 5 m
if the volume exceeds 11 m
directly to the outside no air vent is required even if the volume is between 5 m

3

an air vent of effective area of 110 cm2 is required. If it is installed

3

and 10 m3 an air vent of effective area of 50 cm2 is required, while

3

no air vent is required. However, if the room has a door which opens

3

and 11 m3. If there are
other fuel burning appliances in the same room, B.S. 5440 Part 2 Current Edition, should be
consulted to determine the requisite air vent requirements. For appliances installed in the Republic of
Ireland please refer to the NSAI- Domestic Gas Installation I.S. 813 Current Editions T able Four.

Location

The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom,
shower room or garage. Before making the cut out in the worktop ensure that there is a minimum
distance of 55 mm between the rear edge of the hob and the wall. A minimum distance of 100 mm
must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum
distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm
If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. The
minimum distance combustible material can be fitted directly above the hob is 700 mm. For
appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813
Current Edition Section 7- Permitted Locations of Appliance.

CLEARANCES REQUIRED WHEN FITTING THE GAS HOB

WITHOUT A COOKER HOOD ABOVE

CLEARANCES REQUIRED WHEN FITTING THE GAS HOB

WITH A COOKER HOOD ABOVE

12

700 mm

100 mm

400 mm

50 mm

55 mm

50 mm

400 mm

FO 2027*

700 mm

100 mm

400 mm

50 mm

55 mm

400 mm

50 mm

FO 2028*

Instructions for the Installer

Installation

Important

This hob must be installed by a competent person to the relevant Gas Standards.

Any gas installation must be carried out by a registered competent person.

The manufacturer will not accept liability , should the above instructions or any of the
other safety instructions incorporated in this book be ignored.

On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so
that the washer is fitted between the components as shown in the diagram. Screw the
parts together without using excessive force.

Gas Connection

Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or
copper.

The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread).
When the final connection has been made, it is essential that a thorough leak test is

carried out on the hob and installation.
Ensure that the main connection pipe does not exert any strain on the hob.

FO 0814

FO 0264

A) Ramp with ending nut
B) Seal
C) Elbow

It is important to install the elbow correctly , with the shoulder on the end of the thread,
fitted to the hob connecting pipe.
Failure to ensure the correct assembly will cause leakage of gas.

13

Instructions for the Installer

Cut Out Size

The dimensions of the cut-out are given in the diagram.

510

880

0

8

4

FO 2349

30

830

150 min

Building In

Building over a cupboard or drawer

If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat
resistant board below the base of the hob on the underside of the work surface.
It is also recommended to carry out the electrical connection to the hob as shown in
diagrams 1 and 2 (See next page).

14

Instructions for the Installer

1

FLEX
OUTLET

FO 0763

ON/OFF SWITCH

FO 0764

2

ON/OFF SWITCH

FLEX
OUTLET

Building over a kitchen unit with door

Proper arrangements must be taken in
designing the furniture unit, in order to avoid
any contact with the bottom of the hob which
can be heated when it is operated. The
recommended solution is shown in diagram

3.
The panel fitted under the hob ("a") should
be easily removable to allow easy access
if technical assistance is needed. The space
behind the kitchen unit ("b") can be used
for connections.

3

60

30

a

20 min

b

FO 1013

Dimensions are given in mm.

15

Instructions for the Installer

Fitting the hob to the worktop

Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside

))

)

))

outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent
spillage near the hob seeping into the cabinet below.

1) Remove the pan supports, the burners caps and crowns and turn the hob upside down,
taking care the ignition electrodes are not damaged in this operation.

2) Place the sealing gasket all around the glass top edge as shown in diagram 4.

3) Fit the hob in the cut out and push it down until the glass top and the working top make
contact, as shown in diagram 5.

4

FO 2320

16

5

FO 2321

a

a) Sealing

Instructions for the Installer

Electrical connections

Any electrical work required to install this hob should be carried out by a qualified
electrician or competent person, in accordance with the current regulations.

THIS HOB MUST BE EARTHED.

The manufacturer declines any liability should these safety measures not be observed.
This hob is designed to be connected to a 230-240V 50Hz AC electrical supply .
Before switching on, make sure the electricity supply voltage is the same as that indicated
on the hob rating plate. The rating plate is located on the bottom of the hob. A copy is
attached on the back cover of this book.
The hob is supplied with a 3 core flexible supply cord incorporating a 3amp plug fitted. In
the event of having to change the fuse, a 3amp AS TA approved (BS 1362) fuse must be
used.
Should the plug need to be replaced for any reason, the wires in the mains lead are
coloured in accordance with the following code:
Green and Y ellow - Earth

Blue - Neutral
Brown - Live

1) Connect the green and yellow (earth) wire

to the terminal in the plug which is marked
with the letter 'E' or the earth symbol

coloured green and yellow.

2) Connect the blue (neutral) wire to the terminal

in the plug which is marked with the letter 'N'
or coloured black.

3) Connect the brown (live) wire to the terminal

in the plug which is marked with the letter 'L' or coloured red.
Upon completion there must be no cut, or stray strands of wire present and the cord
clamp must be secure over the outer sheath.
In the event of having to change the fuse, a 3amp AST A approved (BS 1362) fuse must
be used.

or

FO 0390

A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of safely .

17

Instructions for the Installer

Permanent Connection

In the case of a permanent connection, it is necessary that you install a double pole switch
between the hob and the electricity supply (mains), with a minimum gap of 3 mm between
the switch contacts and of a type suitable for the required load in compliance with the
current electric regulations.
The switch must not break the yellow and green earth cable at any point.

Ensure that the hob supply cord does not come into contact with surfaces with
temperatures higher than 50 deg. C.

Replacement of the cable

The connection of the voltage cable to the appliance's terminal block is of type "Y". This
means that its replacement requires the specific equipment of a technician.
In this case, only cable types H05RR-F , H05 V2V2-F (T90) or H05 BB-F must be used.
The cable section must be suitable to the voltage and the working temperature.
The yellow/green earth wire must be approximately 2 cm longer than the phase wires.

Wiring diagram

18

1. IGNITOR SWITCHES

2. IGNITOR UNIT

3. LED POWER INDICAT ORS

Instructions for the Installer

Fault Finding

Preliminary Electrical Systems Check

START

Isolate appliance
and carry out:
A: Earth Continuity
check.

NO YES

Has inlet fuse blown?

NO YES

Inlet wiring
faulty.
Rectify any
fault.

Carry out:

C: Polarity check.

PLUG (with cover removed)

Earth Wire
Green/Yellow

Neutral Wire
Blue

Carry out:
D: Resistance to
Earth check.

Electricity supply
should now be
satisfactory.

( )

FUSE

Brown

Brown

Blue

Blue

SOCKET

(face view)

E

Green
Yellow

Green
Yellow

( )

Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.

N

L

19

Instructions for the Installer

A. EARTH CONTINUITY CHECK

Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and
adjust zero if necessary.

— Test leads from any appliance earth point to earth pin on plug. Resistance should be

less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean
and tight.

B. INSULATION CHECK

Appliance electrically disconnected, all switches ON.
a) meter set on Ω (Ohms) x 1 scale.

T est leads from L to N in appliance terminal block. If meter reads «0» then there is a
short circuit.

b) meter set on Ω (Ohm) x 100 scale.

Repeat test with leads from L to E. If meter reads less than ∞ (infinity) there is a fault.

NOTE - Should it be found that the fuse has failed but no fault is indicated - a detailed continuity
check (i.e. by disconnecting and checking each component) is required to trace the faulty
component.

It is possible that a fault could occur as a result of local burning/arcing but no fault could be found
under test. However a detailed visual inspection should reveal evidence of burning around the
fault.

20

Ignition System / Gas Ignition

Instructions for the Installer

Ignitor does not spark

NO

Check plug top fuse and
replace if necessary

Check polarity and earth
continuity of supply point

Check earth continuity
of appliance

Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit

YES

Check gas supply at
burner

Light burner manually

Check by pass simmer
adjusted

Check position of the
electrode

Check continuity from the tip of
each electrode to the terminals 1
to 4 on the ignitor unit

Check fitting of
burners

Check continuity from 'L' on the
mains connector block and the
taps ignition switches

Check continuity from ignition
switches connector to ignitor unit

Check for breaks in the insulation
of the HT leads

Change the taps ignition
switches

Change the ignitor unit

21

Instructions for the Installer

Commissioning

When the hob has been fully installed it will be necessary to check the minimum flame setting. T o
do this, follow the procedure below.

1) Turn the gas tap to the MAX position and ignite.

))

)

))

2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX

several times. If the flame is unstable or is extinguished follow the procedure below.

Procedure:

1) Re-ignite the burner and set to MIN.

))

)

))

2) Remove the control knob.

3) To adjust, use a thin bladed

screwdriver and turn the adjustment
screw (see diagram) until the flame
is steady and does not extinguish,
when the knob is turned from MIN
to MAX. Repeat this procedure for
all burners.

Minimum adjustment screw

Pressure Testing

1) Remove left hand pan support and front left burner cap and crown.

))

)

))

2) Fit manometer tube over the injector.

3) Turn on the burner gas supply and ignite another burner supply .

The pressure reading should be nominally 20mbar and must be between 17 mbar
and 25mbar.

4) Turn off the burner supplies.

22

Instructions for the Installer

Conversion from Natural Gas to LPG

IMPORTANT
The replacement/conversion of the gas hob should only be undertaken by a
competent person.

It is important to note that this model is designed for use with natural gas but can be
converted for use with butane or propane gas providing the correct injectors are fitted and
the gas rate is adjusted to suit.

Method

1) Ensure that the gas taps are in the 'OFF' position

))

)

))

2) Isolate the hob from the electricity supply

3) Remove all pan supports, burner caps, rings, crowns and control knobs.

4) With the aid of a 7mm box spanner the burner injectors can then be unscrewed and
replaced by the appropriate LPG injectors.

To adjust the gas rate

With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment
screw. Upon completion stick the replacement rating plate on the under side of the hob.

23

Service and Spare Parts

In the event of your appliance requiring service, or if you wish to purchase spare parts,
please contact your local Service Force Centre by telephoning
0870 5 929 929

Y our telephone call will be automatically routed to the Service Force Centre covering your
postcode area.For the address of your local Service Force Centre and further informa­tion about Service Force, please visit the website at
www.serviceforce.co.uk

Before calling out an engineer, please ensure you have read the details under the heading
“Something not working”
When you contact the Service Centre, you will need to give the following details:

1. Your name, address and post code.

2. Your telephone number

3. Clear and concise details of the fault

4. The model and the serial number (see rating label on the back of this instruction
booklet)

5. Date of purchase

Customer Care

For general enquiries concerning your Electrolux appliance, or for further information on
Electrolux products please contact our Custo-mer Care Department by letter or telephone
at the address below or vi-sit our website at www.electrolux.co.uk

Customer Care Department

Electrolux Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
T el : 08705 350350*

* calls to this number may be recorded for training purposes.

24

Guarantee Conditions

Standard guarantee conditions

We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG­Electrolux appliance or any part thereof is pro-ved to be defective by reason only of faulty
workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE
for labour, materials or carriage on condition that:

• The appliance has been correctly installed and used only on the elec-tricity supply stated on
the rating plate.

• The appliance has been used for normal domestic purposes only , and in accordance with
the manufacturer’s instructions.

• The appliance has not been serviced, maintained, repaired, taken apart or tampered with
by any person not authorised by us.

• Electrolux Service Force Centre must undertake all service work under this guarantee

• Any appliance or defective part replaced shall become the Company’s property .

• This guarantee is in addition to your statutory and other legal rights..

Exclusions

This guarantee does not cover:

• Damage or calls resulting from transportation, improper use or neg-lect, the replacement of
any light bulbs or removable parts of glass or plastic.

• Costs incurred for calls to put right an appliance which is improperly installed or calls to
appliances outside the United Kingdom.

• Appliances found to be in use within a commercial environment, plus those which are
subject to rental agreements.

• Products of AEG-Electrolux manufacture which are not marketed by AEG-Electrolux.

25

European Guarantee

This appliance is guaranteed by Electrolux in each of the countries listed at the back of this
user manual, for the period specified in the appliance guarantee or otherwise by law. If
you move from one of these countries to another of the countries listed be-low the appliance
guarantee will move with you subject to the following qualificati-ons:

• The appliance guarantee starts from the date you first purchased the appliance which

will be evidenced by production of a valid purchase document issued by the seller of
the appliance.

• The appliance guarantee is for the same period and to the same extent for labour and
parts as exists in your new country of residence for this particular model or range of
appliances.

• The appliance guarantee is personal to the original purchaser of the appliance and
cannot be transferred to another user.

• The appliance is installed and used in accordance with instructions issued by Elec­trolux and is only used within the home, i.e. is not used for commercial purposes.

• The appliance is installed in accordance with all relevant regulations in force within
your new country of residence.

The provisions of this European Guarantee do not affect any of the rights granted to you by
law.

26

27

www.aeg-electrolux.co.uk

AEG Haugeräte GmbH
Postfach 1036
D-90327 Nürnberg

http://www.aeg.hausgeraete.de
© Copyright by AEG

35686-0204 AM 02/07 Grafiche MDM - Forlì