S93880KMB0
S93880KMX0
REFRIGERATOR USER MANUAL
EN
2
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have
created it to give you impeccable performance for many
years, with innovative technologies that help make life
simpler – features you might not find on ordinary
appliances. Please spend a few minutes reading to get the
very best from it.
ACCESSORIES AND CONSUMABLES
In the AEG webshop, you’ll find everything you need to
keep all your AEG appliances looking spotless and
working perfectly. Along with a wide range of accessories
designed and built to the high quality standards you
would expect, from specialist cookware to cutlery baskets,
from bottle holders to delicate laundry bags…
Visit the webshop at:
www.aeg.com/shop
CONTENTS
4 Safety information
6 Control panel
10 Water dispenser
11 First use
12 Daily use
14 Helpful hints and tips
15 Care and cleaning
17 What to do if…
20 Technical data
20 Installation
26 Noises
28 Environmental concerns
Contents
3
The following symbols are used in this user
manual:
Important information concerning your
personal safety and information on how to
avoid damaging the appliance.
General information and tips
Environmental information
Subject to change without notice
4 Safety information
SAFETY INFORMATION
In the interest of your safety and to ensure the correct use, before installing and first using
the appliance, read this user manual carefully, including its hints and warnings. To avoid
unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.
For the safety of life and property keep the precautions of these user's instructions as the
manufacturer is not responsible for damages caused by omission.
Children and vulnerable people safety
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Keep all packaging well away from children. There is risk of suffocation.
• If you are discarding the appliance pull the plug out of the socket, cut the connection
cable (as close to the appliance as you can) and remove the door to prevent playing children to suffer electric shock or to close themselves into it.
• If this appliance featuring magnetic door seals is to replace an older appliance having a
spring lock (latch) on the door or lid, be sure to make that spring lock unusable before
you discard the old appliance. This will prevent it from becoming a death trap for a child.
General safety
WARNING!
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.
• The appliance is intended for keeping foodstuff, production of cold water, with or without carbon dioxide and for beverages in a normal household as explained in this instruction booklet.
• If the gas cylinder is used for other purposes than that intended or if it is filled by an
unauthorised person, all guarantees automatically become null and void.
• Do not use a mechanical device or any artificial means to speed up the thawing process.
• Do not use other electrical appliances (such as ice cream makers) inside of refrigerating
appliances, unless they are approved for this purpose by the manufacturer.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
Safety information 5
During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition
– thoroughly ventilate the room in which the appliance is situated
• It is dangerous to alter the specifications or modify this product in any way. Any damage
to the cord may cause a short-circuit, fire and/or electric shock.
WARNING!
Any electrical component (power cord, plug, compressor) must be replaced by a certified
service agent or qualified service personnel to avoid hazard.
1. Power cord must not be lengthened.
2. Make sure that the power plug is not squashed or damaged by the back of the ap-
pliance. A squashed or damaged power plug may overheat and cause a fire.
3. Make sure that you can come to the mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not insert the power plug. There is a risk of
electric shock or fire.
6.
You must not operate the appliance without the lamp cover
1)
of interior lighting.
• This appliance is heavy. Care should be taken when moving it.
• Do not remove nor touch items from the freezer compartment if your hands are damp/
wet, as this could cause skin abrasions or frost/freezer burns.
• Avoid prolonged exposure of the appliance to direct sunlight.
•
Bulb lamps
2)
used in this appliance are special purpose lamps selected for household
appliances use only. They are not suitable for household room illumination.
Daily use
• Do not put hot pot on the plastic parts in the appliance.
• Do not store flammable gas and liquid in the appliance, because they may explode.
• Appliance's manufacturers storage recommendations should be strictly adhered to. Refer
to relevant instructions.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the mains plug from the
mains socket.
• Do not clean the appliance with metal objects.
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean
the drain. If the drain is blocked, water will collect in the bottom of the appliance.
Installation
For electrical connection carefully follow the instructions given in specific paragraphs.
1) If the lamp cover is foreseen
2) If the lamp is foreseen
6 Control panel
• Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought it.
In that case retain packing.
• It is advisable to wait at least four hours before connecting the appliance to allow the oil
to flow back in the compressor.
• Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.
• Wherever possible the back of the product should be against a wall to avoid touching or
catching warm parts (compressor, condenser) to prevent possible burn.
• The appliance must not be located close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.
•
Connect to potable water supply only.
3)
Service
• Any electrical work required to do the servicing of the appliance should be carried out by
a qualified electrician or competent person.
• This product must be serviced by an authorized Service Centre, and only genuine spare
parts must be used.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The appliance shall not be discarded together
with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local
authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked by the symbol
are recyclable.
CONTROL PANEL
1 2 3 4 5 6
1 ON/OFF button
2 Mode button
3 OK button
4 Temperature colder button
5 Temperature warmer button
6 Display
It is possible to change predefined sound of buttons to a loudly one by pressing together
Mode button and Temperature colder button for some seconds. Change is reversible.
3) If a water connection is foreseen.
Control panel
Display/Indicator
4321
78 56
1 Timer indicator
2 COOLMATIC function
3 Holiday function
4 Temperature indicator
5 Alarm indicator
6 Child Lock function
7 Minute Minder function
8 Humidity function
Switching on
To switch on the appliance do these steps:
1. Connect the mains plug to the power socket.
2. Press the ON/OFF button if the display is off.
3. The temperature indicators show the set default temperature.
To select a different set temperature refer to "Temperature regulation".
WARNING!
If the door remains open for some minutes, the light will turn off automatically. The light is
reset by closing and opening the door itself.
7
Switching off
To switch off the appliance do these steps:
1. Press the ON/OFF button for few seconds.
2. The display switches off.
3. To disconnect the appliance from the power disconnect the mains plug from the pow-
er socket.
Temperature regulation
The set temperature of the fridge may be adjusted by pressing the temperature button.
Set default temperature:
• +5°C for the fridge
The temperature indicator shows the set temperature.
The set temperature will be reached within 24 hours.
After a power failure the set temperature remains stored.
8 Control panel
Minute Minder function
The Minute Minder function is to be used to set an acoustic alarm at the preferred time,
useful for example when a recipe requires to cool down a mixture for a certain lenght of
time.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
The Minute Minder indicator flashes.
The Timer shows the set value (30 minutes) for a few seconds.
2. Press the Temperature colder or the Temperature warmer button to change the Timer
set value from 1 to 90 minutes.
3. Press the OK button to confirm.
The Minute Minder indicator is shown.
The Timer start to flash (min).
At the end of the countdown the Minute Minder indicator flashes and an audible alarm
sounds:
1. Press OK button to switch off the sound and terminate the function.
It is possible to deactivate the function at any time during the countdown:
1. Press the Mode button until the Minute Minder indicator flashes.
2. Press the OK button to confirm.
3. The Minute Minder indicator goes off.
It is possible to change the time during the countdown by pressing the Temperature colder
button and the Temperature warmer button.
Child Lock function
To lock the buttons from unintentional operation select the Child Lock function.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
2. The Child Lock indicator flashes.
3. Press the OK button to confirm.
The Child Lock indicator is shown.
To switch off the function:
1. Press the Mode button until the Child Lock indicator flashes.
2. Press the OK button to confirm.
3. The Child Lock indicator goes off.
COOLMATIC function
If you need to insert a large amount of warm food, for example after doing the grocery
shopping, we suggest activating the COOLMATIC function to chill the products more rapidly
and to avoid warming the other food which is already in the refrigerator.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
The COOLMATIC indicator flashes.
Control panel
2. Press the OK button to confirm.
The COOLMATIC indicator is shown.
The COOLMATIC function shuts off automatically after approximately 6 hours.
To switch off the function before its automatic end:
1. Press the Mode button until the COOLMATIC indicator flashes.
2. Press the OK button to confirm.
3. The COOLMATIC indicator goes off.
The function switches off by selecting a different fridge set temperature.
Extra Humidity function
If you need to increase the humidity in the refrigerator, we suggest activating the Extra
Humidity function:
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
The Extra Humidity indicator flashes.
2. Press the OK button to confirm.
The Extra Humidity indicator is shown.
To switch off the function:
1. Press the Mode button until the Extra Humidity indicator flashes.
2. Press the OK button to confirm.
3. The Extra Humidity indicator goes off.
9
Holiday function
This function allows you to keep the refrigerator closed and empty during a long holiday
period without the formation of a bad smell.
The fridge compartment must be empty with holiday function on.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
The Holiday indicator flashes.
The fridge temperature indicator shows the set temperature.
2. Press the OK button to confirm.
The Holiday indicator is shown.
To switch off the function:
1. Press the Mode button until the Holiday indicator flashes.
2. Press the OK button to confirm.
3. The Holiday indicator goes off.
The function switches off by selecting a different fridge set temperature.
10 Water dispenser
Door open alarm
An acoustic alarm will sound if the door is left open for a few minutes. The door open alarm
conditions are indicated by:
• flashing Alarm indicator
• acoustic buzzer
When normal conditions are restored (door closed), the alarm will stop.
During the alarm, the buzzer can be switched off by pressing any button.
WATER DISPENSER
1
1 Child lock indicator
2 Carbonated water button
3 Plain water button
4 Water filter indicator
5 Water outlet
6 Flap
7 Illumination
2
6 57
3
Child lock function
The child lock function is activated at delivery.
Temporary unlocking
Press button 2 or 3 for about three seconds until the child lock indicator light (1) goes out.
The child lock function is reactivated automatically after about three seconds.
4
Permanent unlocking
Press buttons 2 and 3 at the same time for about three seconds.
The button 2 or 3 lights up to indicate unlocking and the child lock indicator (1) goes out.
To activate the child lock function
Press buttons 2 and 3 at the same time for about three seconds.
The child lock indicator is lit when activated.
First use
Selecting and dispensing water
Before dispensing water, select either carbonated water (2) or plain water (3). The actual
choice is indicated by the lit button.
Water selection can be changed while the water is running.
Water is dispensed by pressing a glass or other container towards the flap (6). Draw back
the glass or container to stop the water flow.
Any water that drips or is spilled is collected in the drip tray below the water dispenser. The
drip tray can be detached and emptied when necessary.
Lighting
The water dispenser lighting (7) illuminates automatically when water is dispensed.
For continuous lighting
1. Make sure that the water dispenser is unlocked.
2. Press the plain water button (3) until the lighting goes on (about three seconds).
Brightness is now about 50% until the dispenser is used.
Switch off the lighting
1. Make sure that the water dispenser is unlocked.
2. Press the plain water button (3) until the lighting goes out (about three seconds).
Water filter indicator
When the water filter indicator (4) lights up the water filter has about 20% remaining lifetime. In this situation, it is recommended that you buy a replacement filter.
When the water filter indicator starts flashing, the water filter lifetime is consumed .
Replace the water filter without delay, refer to "Installation of the water filter".
When the water filter is replaced. Press the plain water button (3) for a few seconds to reset
the water filter indicator.
11
FIRST USE
Cleaning the interior
Before using the appliance for the first time, wash the interior and all internal accessories
with lukewarm water and some neutral soap so as to remove the typical smell of a brandnew product, then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
12 Daily use
Check that the drain hose at the rear of the cabinet discharges into the drip tray.
DAILY USE
Movable shelves
The walls of the refrigerator are equipped with a
series of runners so that the shelves can be positioned as desired.
Some shelves must be lifted up by the rear edge
to enable them to be removed.
Do not move the glass shelf above the vegetable
drawer to ensure correct air circulation.
Vegetable Drawer
The drawer is suitable for storing fruit and vegetables.
Some models have a separator inside the drawer that can be placed in different positions to
allow for the subdivision best suited to personal needs.
All parts inside the drawer can be removed for cleaning purposes.
Daily use 13
Bottle rack
Place the bottles (with the opening facing front)
in the pre-positioned shelf.
If the shelf is positioned horizontally, place only
closed bottles.
This bottle holder shelf can be tilted in order to
store previously opened bottles. To obtain this result, pull the shelf up so it can rotate upwards and
be placed on the next higher level.
Clean Air Control Filter
Your appliance is equipped with a carbon filter behind the air lever flap.
The filter purifies the air from unwanted odours in the fridge compartment preserving food
quality.
On delivery the filter is in a plastic bag. Refer to "Installation of the Clean Air Control filter"
for instructions.
Make sure that the air lever flap is closed to obtain proper function.
Positioning the door shelves
To permit storage of food packages of various sizes, the door shelves can be placed at different heights.
Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
Do not move the lower door shelf to ensure correct air circulation.
14 Helpful hints and tips
HELPFUL HINTS AND TIPS
Hints for energy saving
• Do not open the door frequently or leave it open longer than absolutely necessary.
• If the ambient temperature is high and the Temperature Regulator is set to low tempera-
ture and the appliance is fully loaded, the compressor may run continuously, causing
frost or ice on the evaporator. If this happens, set the Temperature Regulator toward
warmer settings to allow automatic defrosting and so a saving in electricity consumption.
Hints for fresh food refrigeration
To obtain the best performance:
• do not store warm food or evaporating liquids in the refrigerator
• do cover or wrap the food, particularly if it has a strong flavour
• position food so that air can circulate freely around it
Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable
drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
Hints for temperature inside the fridge
A suitable temperature inside the fridge is approx. +5° C. When the temperature regulator
is set to +5°C this represents the mean temperature in the fridge. It is normal with higher
temperature in the top of the fridge.
If the temperature regulator is set to a cold temperature, the ambient temperature is high
or if the fridge is fully loaded the compressor will run for a longer time. It too cold, change
to a higher temperature setting.
Do not place food against or close to the temperature sensor. This can result in too cold temperatures.
Care and cleaning 15
If you want to check the temperature of food
stored in the refrigerator, place a glass of water
centrally in the cabinet, and put a proper thermometer with an accuracy of +/– 1 °C into it. After 6 hours the temperature can be monitored.
The measuring shall be performed under steadystated conditions (without changing the load).
CARE AND CLEANING
CAUTION!
Unplug the appliance before carrying out any maintenance operation.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must
therefore only be carried out by authorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with lukewarm water and some neutral soap.
• regularly check the door seals and wipe clean to ensure they are clean and free from
debris.
• rinse and dry thoroughly.
Do not pull, move or damage any pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders, highly perfumed cleaning products or wax polishes
to clean the interior as this will damage the surface and leave a strong odour.
Clean the condenser (black grill) and the compressor at the back of the appliance with a
brush. This operation will improve the performance of the appliance and save energy consumption.
Take care of not to damage the cooling system.
When moving the cabinet, lift it by the front edge to avoid scratching the floor.
16 Care and cleaning
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the
plastics used in this appliance. For this reason use a soft cloth rinsed in warm water and
neutral soap emulsion for cleaning external surfaces.
Do not use detergents or abrasive paste as these will damage the paint, or stainless steel
anti finger print coating.
After cleaning, reconnect the equipment to the mains supply.
Replacing the Clean Air Control filter
To get the best performance replace the Clean Air Control filter once every year.
New active filters can be purchased from your local dealer.
Refer to "Installation of the Clean Air Control filter" for instructions.
Replacing the water filter
Remove the filter. A small amount of water will run out. Dry off and fit the new filter.
Refer to "Installation of the water filter"
Replacement filters can be ordered from Electrolux Service Force Centre,
The water connection does not need to be switched off when changing the filter.
Replacing the gas cylinder
Remove the gas cylinder, refer to "Installation of the gas cylinder"
The replacement gas cylinder is obtained through your local dealer.
Cleaning the water dispenser
When necessary, clean the surfaces of the dispenser, using only a soft cloth and warm water.
The dispenser drip tray can be cleaned with a lukewarm water and some neutral soap. Lime
deposits on the dispenser surface can removed using vinegar or diluted acetic acid as cleaning agent. Wipe clean with a damp cloth.
Cleaning the ventilation grille
The ventilation grille can be removed for washing.
Make sure the door is open and then:
1. Loosen the upper edge of the grille by
pulling outward/downward.
2. Pull the grille straight out to completely
remove it.
3. Vacuum clean under the cabinet.
Defrosting the refrigerator
Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out
What to do if… 17
through a drain hole into a special container at the back of the appliance, over the motor
compressor, where it evaporates.
Periods of non-operation
When the water system is not use for a long period, turn off the water connection to the
refrigerator.
• A filter that has been in service shall not be exposed to temperatures below 0°C as crack-
ing of the filter body may occur due to freezing expansion.
• If the filter still is to be preserved for later reuse, suitable storage temperature will be
+5°C.
When the appliance is not in use for long periods, take the following precautions:
1. disconnect the appliance from electricity supply
2. remove all food
3. clean the appliance and all accessories
4. leave the door/doors open to prevent unpleasant smells.
Before using the appliance again, rinse the system thoroughly by dispensing at least three
litres (5 pints) of water.
• If necessary, the system can be cleaned by using a sanitizing kit which can be ordered
through Electrolux Service Force Centre or through our website www.electrolux.com.
If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food
inside from spoiling in case of a power failure.
WHAT TO DO IF…
During operation of the appliance some smaller but annoying trouble can often occur,
which does not require calling a technician out. In the following chart information is given
about them to avoid unnecessary charges on service.
The operation of the appliance goes with certain sounds (compressor and circulating
sound). This not means a trouble, but a normal operation.
The appliance operates discontinuously, so the stopping of compressor does not mean being no current. That is why you must not touch the electrical parts of the appliance before
breaking the circuit.
Problem Possible cause Solution
The appliance is noisy. The appliance is not supported
Sound level is too high
during dispensing of water.
The buzzer sounds. The
Alarm icon flashing.
properly.
The transport supporting tie of
the water system pressure pump
has not been removed.
The door is not closed correctly. Refer to "Door open alarm".
Check if the appliance stands stable (all feet and wheels should be
on the floor). Refer to "Levelling".
Remove the tie. Refer to "Removing the transport support".
18 What to do if…
Problem Possible cause Solution
upper or lower square
is shown in the temperature display.
The compressor runs continuously.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too
The food temperature is too
The room temperature is too
Water flows inside the refrigerator.
Food prevent that water flows
Water flows on the
ground.
The temperature in the
appliance is too cold.
The temperature in the
appliance is too warm.
The door is not closed correctly. Refer to "Closing the door".
The food temperature is too
The temperature in the refrigeration is too warm.
Large quantities of food to be
The appliance does not
operate.
The mains plug is not connected
An error has occurred in measuring the temperature
The Temperature regulator may
be set incorrectly.
frequently.
high.
high.
The water outlet is clogged. Clean the water outlet.
into the water collector.
The melting water outlet does
not flow in the evaporative tray
above the compressor.
The Temperature regulator may
be set incorrectly.
The Temperature regulator may
be set incorrectly.
warm.
There is no cold air circulation in
the appliance.
cooled were put in at the same
time.
The appliance is switched off. Switch on the appliance.
to the mains socket correctly.
Call your service representative
(the cooling system will continue
to keep food products cold, but
temperature adjustment will not
be possible)
Set a warmer temperature.
Do not keep the door open longer
than necessary.
Let the food temperature decrease to room temperature before storage.
Decrease the room temperature.
Make sure that food do not touch
the rear plate.
Attach the melting water outlet
to the evaporative tray.
Set a warmer temperature.
Set a colder temperature.
Let the food temperature decrease to room temperature before storage.
Make sure that there is cold air
circulation in the appliance.
Insert smaller quantities of food
to be cooled at the same time.
Connect the mains plug to the
mains socket correctly.
What to do if…
Problem Possible cause Solution
The appliance has no power.
Not enough carbon dioxide in the water.
Too much carbon dioxide
in the water.
No carbon dioxide. The gas cylinder is empty. Refer to "Replacing gas cylinder"
No or very low water flow. The gas cylinder is empty. Refer to "Replacing gas cylinder".
Sediment in the water. Remove and clean the strainer in
Water supply obstructed. Check water supply.
Only gas comes out when
dispensing carbonated water.
Sediment in the water. Remove and clean the strainer in
The water filter indicator
flashes.
The water filter indicator
lights constantly.
The water dispenser lamp
and the child lock indicator flashes.
Leakage from filter operation. Open water module hatch and
Dispensing is interrupted
after a short time.
The lamp does not work. The door has been open to long. Close the door.
The lamp is defective. Refer to "Replacing the lamp".
Door interferes with ventilation grill.
Misaligned door. The appliance is not levelled. Refer to "Levelling".
There is no voltage in the mains
socket.
The carbon dioxide is running
out.
Dilute with ordinary water. Refer to "Selecting and dispens-
Water supply obstructed. Check water supply.
The filter has been totally consumed.
20% of filter capacity remains. Buy a new filter.
Internal leakage at the water
connection.
The maximum time of two minutes is exceeded.
The appliance is not levelled. Refer to "Levelling".
Connect a another electrical appliance to the mains socket.
Check fuse. Contact a qualified
electrician.
Refer to "Installation of the gas
cylinder".
ing water".
the inlet hose connection.
the inlet hose connection.
Refer to "Replacing the water filter".
Contact your local Electrolux
Service Force Centre.
dry up water from the bottom,
look for leakages.
If filter leaks, refer to "Replacing
the water filter"
Start new dispensing.
19
As much as the advice does not lead to result, call the nearest brand-mark service.
Replacing the lamp
The appliance is equipped with a longlife LED interior light.
20 Technical data
Only service is allowed to replace the lighting device. Contact your Service Center .
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to "Installation".
3. If necessary, replace the defective door gaskets. Contact the Service Center.
TECHNICAL DATA
S93880KMB0 S93880KMX0
Dimension
Height 1810 mm 1810 mm
Width 595 mm 595 mm
Depth 650 mm 650 mm
Voltage 230 V 230 V
Frequency 50 Hz 50 Hz
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
Water pressure range
The water pressure must be at least 1 bar (100kPa) Consult your installer if water pressure is
Highest allowed water pressure 10 bar (1000kPa) If water pressure exceeds 10 bar a re-
Capacity 50-80 litres of carbonated water per cylinder.
• Do not connect the appliance in spaces where ambient temperature can decrease to below freezing.
• The appliance may only be connected to drinking water supplies.
• The appliance may only be connected to cold water supplies.
less than 1 bar.
duction valve must be fitted (available
from your specialist shop).
INSTALLATION
WARNING!
Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
Positioning
Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:
Installation 21
Climate class Ambient temperature
SN +10°C to + 32°C
N +16°C to + 32°C
ST +16°C to + 38°C
T +16°C to + 43°C
Location
To ensure best performance, if the appliance is positioned below an overhanging wall unit,
the minimum distance between the top of the cabinet and the wall unit must be at least 40
mm . Ideally, however, the appliance should not be positioned below overhanging wall
units.
The ventilation space can be:
• directly above the appliance
• behind and above the top cupboard.
In this case, the space behind the top cupboard
must be at least 50 mm deep.
50mm
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply.
The appliance must be earthed. The power supply cable plug is provided with a contact for
this purpose. If the domestic power supply socket is not earthed, connect the appliance to a
separate earth in compliance with current regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if the above safety precautions are not observed.
This appliance complies with the E.E.C. Directives.
Removing the transport support
Your appliance is equipped with transport support to secure the door during transportation.
To remove them do these steps:
22 Installation
1. Open the door.
2. Remove the transport support from the
door sides.
3. Remove the transport support from the
lower hinge (some models).
4. Remove the transport support from un-
derneath the water unit.
5. Cut the pump securing tie and remove
it.
Some models are fitted with a silencing pad
under the cabinet. Do not remove this pad.
3
2
5
Rear spacers
Install the spacers provided within the accessory bag as shown in the figure.
Install two spacers on the back side of the panel
and two spacers with adhesive on the lower part.
Connecting the water hose.
Water supply should be provided with a tap and 3/4" male connector within 1,5 m from the
appliance.
4
Installation 23
This work is to be carried out by a skilled plumber.
There are different type-approved taps and tap assemblies on the market.
The water hose must not be cracked, squeezed or put in tight bends.
Before the appliance is placed its final location, ensure that the water connection has been
correctly carried out, that there is no leakage at the connection to the water tap.
Tighten the screw enough by hand.
Make sure that the gasket is properly positioned in the connector.
We recommend that the appliance is placed on a "run-off" mat intended for refrigerators
and freezers, which makes it easier to detect possible leakage
Fitting the door handles
(Example for right hinge performance)
The handles are supplied as a kit at delivery.
1. Screw the top handle bracket to the
handle rod.
2. Fit the bottom handle bracket on the
lower left-hand side of the door.
3. Fit the top handle bracket on the top
left-hand side of the door.
4. Screw the handle rod to the bottom
handle bracket.
Do not use excessive force and overtighten
the screws (max. 2 Nm) as you may damage
the door handles.
12
43
Levelling
When placing the appliance ensure that it stands
level. If necessary adjust the feet using the adjustment spanner supplied.
Door alignment is dependent on proper levelling.
Installation of the Clean Air Control filter
The Clean Air Control filter is an active carbon filter which absorbs bad odours maintain the
best flavour and aroma for all foodstuffs without risk of odour cross contamination.
On delivery the carbon filter is in a plastic bag to preserve performance.
24 Installation
1. Open the air lever flap.
2. Take the filter out of the plastic bag.
3. Insert the filter in the slot found in the
back of the air lever flap.
4. Close the air lever flap.
The filter should be handled carefully so
fragments do not loosen from the surface.
Make sure that the air lever flap is closed to
obtain proper function.
Starting the water system for the first time.
Ensure proper connection to the water supply, refer to "Connecting the water hose".
1. Open the tap on the water connection.
2. Start the refrigerator (switch off and restart if it is already running).
The water system main valve opens and the pump starts to fill the system.
Installation of the water filter
Unpack the filter.
1. Remove the accessories in front of the
water module and open the service
hatch.
2. Place a cloth or a piece of kitchen towel
in the space beneath the water filter.
3. Pull the bypass cartridge outwards,
grasping the lower part, until the water
bypass cartridge is automatically ejected.
4. Remove the protective wrapping of the
new water filter and insert the new filter firmly into the filter connection.
5. Push the water filter back to its original
position.
6. Remove cloth or towel and make sure
that spilled water is wiped off.
7. Close the hatch and remount the interi-
or.
8. Keep the bypass cartridge for future use.
9. Unlock the water dispenser. Refer to
"Child lock functions". Select plain water
and dispense about 2 litres of water.
There may be some air to start with.
Installation 25
Installation of the gas cylinder
1. Remove the gas cylinder wrapping and
screw on the adapter to the gas cylinder. Tighten by hand only.
26 Noises
2. Position the gas cylinder with the
adapter attached underneath the valve
and ensure that the hooks of the lever
system supports the protruding parts of
the adapter.
3. Then turn the lever upwards in one con-
tinuous movement.
4. Unlock the water dispenser, refer to
"Water dispenser functions". Choose
carbonated water and dispense further
1,5 litres (2,5 pints) of water.
5. The system is now ready for use. In or-
der to obtain the best possible performance from the refrigerator, wait until
the set temperature is reached.
2
1
Door reversibility
It is not possible to change the opening direction of the door.
The water supply goes through the hinge to the water dispenser. Contact your dealer for
more information.
NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
SSSRRR!
Noises 27
CLICK!
OK
CLICK!
BRRR!
HISSS!
BLUBB!
BRRR!
CRACK!
CLICK!
BRRR!
BLUBB!
BLUBB!
28 Environmental concerns
HISSS!
HISSS!
SSSRRR!
SSSRRR!
CRACK!
CRACK!
ENVIRONMENTAL CONCERNS
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
293031
www.aeg.com/shop 298376902-B-112011
Loading...