L7WEC166R
USER
MANUAL
EN User Manual
Washer Dryer
www.aeg.com2
CONTENTS
1. SAFETY INFORMATION............................................................................................. 3
2. SAFETY INSTRUCTIONS.............................................................................................6
3. INSTALLATION............................................................................................................7
4. PRODUCT DESCRIPTION.........................................................................................12
5. CONTROL PANEL..................................................................................................... 13
6. DIAL AND BUTTONS................................................................................................ 15
7. PROGRAMMES..........................................................................................................17
8. BEFORE FIRST USE................................................................................................... 23
9. SETTINGS...................................................................................................................24
10. DAILY USE................................................................................................................24
11. DAILY USE - WASHING & DRYING....................................................................... 29
12. DAILY USE - DRYING ONLY...................................................................................31
13. FLUFF IN THE FABRICS..........................................................................................32
14. HINTS AND TIPS..................................................................................................... 32
15. CARE AND CLEANING.......................................................................................... 34
16. TROUBLESHOOTING.............................................................................................39
17. CONSUMPTION VALUES.......................................................................................42
18. TECHNICAL DATA..................................................................................................43
19. ACCESSORIES.........................................................................................................44
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1. SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent
disability.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away unless continuously supervised.
• Children of less than 3 years of age should be kept
away unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of
it appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when
the door is open.
• If the appliance has a child safety device, it should be
activated.
• Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
ENGLISH 3
1.2 General Safety
• Do not change the specification of this appliance.
www.aeg.com4
• This appliance is intended to be used in household
and similar applications such as:
– staff kitchen areas in shops, offices and other
working environments;
– by clients in hotels, motels, bed & breakfast and
other residential type environments;
– areas for communal use in blocks of flats or in
launderettes.
• The appliance shall be installed as a freestanding
product or below the kitchen worktop if space
margins permit.
• Do not install the appliance behind a lockable door, a
sliding door or a door with a hinge on the opposite
side, that would prevent the appliance door from
being fully open.
• Connect the mains plug to the mains socket only at
the end of the installation process. Make sure that the
mains plug is accessible after installation.
• The ventilation opening in the base must not be
covered by a carpet, mat, or any floor covering.
• WARNING: The appliance must not be supplied
through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on
and off by a utility.
• Ensure good air ventilation in the room where the
appliance is installed to avoid the backflow of
unwanted gases into the room from appliances
burning gas or other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is
used for exhausting fumes from any appliances
burning gas or other fuels.
• The operating water pressure at the water entry point
from the outlet connection must be between 0.5 bar
(0.05 MPa) and 8 bar (0.8 MPa).
• Do not exceed the maximum load of 10 kg (refer to
the "Programme chart" chapter).
ENGLISH 5
• The appliance must be connected to the water mains
using the new supplied hose sets, or other new hose
sets supplied by the Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must
be replaced by the manufacturer, its Authorised
Service Centre or similarly qualified persons to avoid
an electrical hazard.
• Wipe away lint or packaging debris that has
accumulated around the appliance.
• Items that have been soiled with substances such as
vegetable or mineral oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and wax
removers should be washed separately with an extra
amount of detergent before being dried in the washer
dryer.
• Do not use the appliance if items have been soiled
with industrial chemicals.
• Do not dry unwashed items in the wash dryer.
• Items such as foam rubber (latex foam), shower caps,
waterproof textiles, and rubber backed articles and
clothes, or pillows fitted with foam rubber pads should
not be dried in the washer dryer.
• Fabric softeners, or similar products, should only be
used as specified by the product manufacturer’s
instructions.
• Remove all objects from items that could be a source
of fire ignition such as lighters or matches.
• Never stop the washer dryer before the end of the
drying cycle unless all items are quickly removed and
separated so that residual heat can dissipate.
• The final part of the washer dryer cycle takes place
without heat (cool down cycle) to ensure that items
reach a temperature that will not cause damage to
them.
• Do not use high pressure water sprays and/or steam
to clean the appliance.
www.aeg.com6
• Clean the appliance with a moist cloth. Use only
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
2. SAFETY INSTRUCTIONS
2.1 Installation
The installation must comply
with relevant national
regulations.
• Follow the installation instructions
supplied with the appliance.
• Do not install or use the appliance
where the temperature can be less
than 0°C or where it is exposed to the
weather.
• Always keep the appliance vertical
when it is being moved.
• Make sure that there is air circulation
between the appliance and the floor.
• Remove all the packaging and the
transit bolts.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Keep the transit bolts in a safe place.
If the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Do not install the appliance where the
appliance door cannot be fully
opened.
• Adjust the feet to have the necessary
space between the appliance and the
flooring.
• When the appliance is in its
permanent position, check if it is
levelled correctly with the aid of a
spirit level. If it is not, adjust the feet
accordingly.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Do not touch the mains cable or the
mains plug with wet hands.
• UK and Ireland only. This appliance is
fitted with a 13 A mains plug. If it is
necessary to change the mains plug
fuse, use only a 13 A ASTA (BS 1362)
fuse.
• This appliance complies with the
E.E.C. Directives.
2.3 Water Connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes,
pipes not used for a long time, where
repair work has been carried out or
new devices fitted (water meters,
etc.), let the water flow until it is clean
and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
ENGLISH 7
2.4 Use
WARNING!
Risk of injury, electric shock,
fire, burns or damage to the
appliance.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not touch the glass door while a
programme is in operation. The glass
can get hot.
• Do not dry damaged (torn, frayed)
items that contain padding or fillings.
• If laundry has been washed with a
stain remover, carry out an additional
rinse cycle before starting a drying
cycle.
• Make sure that all metal objects are
removed from the laundry.
• Only dry fabrics that are suitable to
dry in the washer dryer. Follow the
cleaning instruction on the item label.
• Plastic items are not heat resistant.
– If a detergent ball is used, remove
it before starting a drying
programme.
– Do not use a detergent ball if
setting a non-stop programme.
WARNING!
Risk of injury or damage to
the appliance.
• Do not sit or stand on the open door.
• Do not dry dripping wet clothes in the
appliance.
2.5 Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
2.6 Disposal
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Remove the door catch to prevent
children or pets from becoming
trapped in the drum.
• Dispose of the appliance in
accordance with local requirements
for the disposal of Waste Electrical
and Electronic Equipment (WEEE).
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Unpacking
WARNING!
Remove all the packaging
and the transit bolts before
installing the appliance.
WARNING!
Use the gloves.
1. Remove the external film. If
necessary, use a cutter.
2. Remove the cardboard top and the
polystyrene packaging materials.
1
2
www.aeg.com8
3. Remove the internal film.
4. Open the door and remove the
polystyrene piece from the door seal
and all the items from the drum.
7. Remove the polystyrene protection
from the bottom.
8. Pull up the appliance in vertical
position.
9. Remove the power supply cable and
the drain hose from the hose holders.
5. Carefully put the appliance down on
its rear side.
6. Put the front polystyrene packaging
element on the floor under the
appliance.
Make sure not to
damage the hoses.
It is possible to see
water flowing from the
drain hose. This is due to
the testing with water of
the appliance in factory.
10. Remove the three bolts by using the
spanner supplied with the appliance.
11. Pull out the plastic spacers.
x4
12. Put the plastic caps, that you find in
the user manual bag, in the holes.
We recommend that you
keep the packaging and the
transit bolts for any
movement of the appliance.
3.2 Installation on suspended
flooring
Suspended wooden floors are
particularly susceptible to vibration.
To limit vibration we recommend placing
a waterproof wooden panel, at least 15
mm thick, under the appliance. It should
be screwed to at least 2 floor beams and
should extend beyond the front feet.
If possible, install the appliance where
the floor is more stable.
ENGLISH 9
2. Loosen or tighten the feet to adjust
the level.
WARNING!
Do not put cardboard, wood
or equivalent materials
below the appliance feet to
adjust the level.
The appliance must be level and stable.
A correct adjustment of the
appliance level prevents the
vibration, noise and the
movement of the appliance
when in operation.
When the machine is
installed on a plinth or if a
washer dryer is stacked on
the washing machine, use
the accessories described in
chapter 'Accessories'. Read
carefully the instructions
supplied with the appliance
and with the accessory.
3.3 Positioning and levelling
1. Install the appliance on a flat hard
floor.
Make sure that carpets do
not stop the air circulation
below the appliance.
Make sure that the
appliance does not touch
the wall or other units.
3.4 The inlet hose
1. Connect the water inlet hose to the
back of the appliance.
20O20
O
45O45
O
www.aeg.com10
2. Position it toward left or right
depending on the position of the
water tap.
Make sure that the inlet hose
is not in vertical position.
3. If necessary, loose the ring nut to set
it in the correct position.
4. Connect the water inlet hose to the
cold water tap with 3/4" thread.
You can extend the drain
hose to maximum 400 cm.
Contact the authorized
service centre for the other
drain hose and the
extension.
It is possible to connect the drain hose in
different ways:
1. Make a U shape with the drain hose
and put it around the plastic hose
guide.
2. On the edge of a sink - Fasten the
guide to the water tap or to the wall.
Make sure that the plastic
guide cannot move when
the appliance drains.
CAUTION!
Make sure that there are no
leaks from the couplings.
Do not use an extension
hose if the inlet hose is too
short. Contact the service
centre for the replacement
of the inlet hose.
3.5 Water drainage
The drain hose should be positioned at a
height of not less than 60 cm and not
more than 100 cm from the floor.
Make sure that the drain
hose end is not immersed in
the water. There may be a
return of dirty water into the
appliance.
3. To a stand pipe with vent-hole Insert the drain hose directly into a
drain pipe. Refer to the illustration.
The end of the drain hose
must always be ventilated ,
i.e. the inner diameter of the
drain pipe (min. 38 mm min. 1.5") must be larger
than the external diameter
of the drain hose.
4. If the end of the drain hose looks like
this (see the picture), you can push it
directly into the stand pipe.
ENGLISH 11
5. Without the plastic hose guide, to
a sink spigot - Put the drain hose in
the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the drain
hose makes a loop to
prevent particles going into
the appliance from the sink.
6. Position the hose directly to a builtin drain pipe in the room wall and
tighten it with a clamp.
1 2 3
9
5
6
7
4
10
8
11 12
www.aeg.com12
4. PRODUCT DESCRIPTION
4.1 Appliance overview
Worktop
1
Detergent dispenser
2
Control panel
3
Door handle
4
Rating plate
5
Drain pump filter
6
Feet for levelling the appliance
7
Drain hose
8
Inlet hose connection
9
Mains cable
10
Transit bolts
11
Hose support
12
5. CONTROL PANEL
A
nti
-
cr
ease
Quic
k W
a
sh
Start/Paus e
Program me
Cottons
Cottons Eco
Synthet ics
Delicat es
Dry
Wash
Steam
Rinse
Sp
in/Drai n
NonStop 60min
Outdoor
Wool
/Handwas
h
Auto Drying
Time Dry ing
Temp.
Spin
Stain
s/
Prewash
De
la
y
S
t
art
Mode
2
3
6
12 11 10 8
1
4
5
7
9
13
MIX
5.1 Control panel description
ENGLISH 13
Programme dial
1
Display
2
Drying time touch button (Time
3
Drying)
Drying level touch button (Auto
4
Drying)
Washing and drying mode touch
5
button (Mode)
• Wash
• Dry
Start and pause touch button (Start/
6
Pause)
5.2 Display
Delay Start touch button (Delay Start)
7
Time Saving touch button (Quick
8
Wash)
Anti-crease touch button (Anti-
9
crease)
Anti-stain and prewash touch button
10
(Stains/Prewash)
Spin reduction touch button (Spin)
11
On/Off push button (On/Off)
12
Temperature touch button (Temp.)
13
www.aeg.com14
Laundry weight indicator. The icon flashes during laundry load estimation (refer to "PROSENSE load detection" paragraph).
Maximum laundry indicator. It flashes when the laundry load exceeds
the maximum declared load of the selected programme.
Detergent quantity indicator: the value shows the percentage of detergent quantity needed.
Child safety lock indicator.
Drying time indicator.
Door locked indicator.
The digital indicator can show:
• Programme duration (e. g.
, washing and/or drying phase).
• Delay time (e. g. or ).
• Cycle end ( ).
• Warning code (e.g.
).
Washing phase indicator: it flashes during prewash and wash phase.
Rinsing phase indicator. It flashes during rinse phase.
The permanent Extra Rinse option:
• - one additional rinse.
• - two additional rinses.
Spin and drain phase indicator. It flashes during spin and drain phase.
Steam phase indicator.
Drying phase indicator.
Iron drying indicator.
Cupboard drying indicator.
Extra drying indicator.
Temperature indicator. The indicator appears when a cold wash is
set.
Spin speed indicator.
Rinse hold indicator.
Quiet indicator.
Pre-wash indicator.
Stain indicator.
ECO Energy saving indicators. It appears when you set the Cottons Eco pro-
gramme.
Delay start indicator.
6. DIAL AND BUTTONS
ENGLISH 15
6.1 On/Off
Pressing this button for a few seconds
allows to activate or deactivate the
appliance. Two different tunes sound
while switching the appliance on or off.
As the Stand-by function automatically
deactivates the appliance to decrease
the energy consumption in a few cases,
you may need to activate the appliance
again.
For more details, refer to Stand-by
paragraph in Daily Use chapter.
6.2 Introduction
The options/functions are
not selectable with all
washing programmes. Check
the compatibility between
options/functions and
washing programmes in the
"Programme Chart". An
option/function can exclude
another one, in this case the
appliance doesn't allow you
to set the incompatible
options/functions together.
Make sure the screen and
touch buttons are always
clean and dry.
6.3 Temp.
When you select a washing programme,
the appliance automatically proposes a
default temperature.
Touch this button repeatedly until the
desired temperature value appears on
the display.
When the display shows the indicators
and , the appliance does not
heat the water.
6.4 Spin
When you set a programme, the
appliance automatically selects the
maximum spin speed.
Touch this button repeatedly to:
• Decrease the spin speed.
The display shows only
the spin speeds available
for the set programme.
• Activate the Rinse Hold option .
The water of the last rinse is not
drained out to prevent the fabrics
from creasing. The washing
programme ends with water in the
drum and the final spin phase is not
performed.
The display shows the indicator
The drum turns regularly to reduce
creasing.
The door stays locked. The drum
turns regularly to reduce creasing.
You must drain the water to unlock
the door.
Touch Start/Pause button: the
appliance performs the spinning
phase and drains the water.
• Activate the Quiet option.
All spinning phases (intermediate spin
and final spin) are suppressed and the
.
www.aeg.com16
programme ends with water in the
drum. This helps to reduce creasing.
As the programme is very quiet, it is
suitable for use at night time when
cheaper electricity tariffs are available.
In some programmes the rinses are
performed with more water.
The display shows the indicator
The door stays locked. The drum
turns regularly to reduce creasing.
You must drain the water to unlock
the door.
Touch the Start/Pause button: the
appliance performs only the draining
phase.
The appliance empties the
water out automatically after
approximately 18 hours.
6.5 Stains/Prewash
Press this button repeatedly to activate
one of the two options.
The relevant indicator goes on in the
display.
• Stains
Select this option to add an anti-stain
phase to a programme in order to
treat heavily soiled or stained laundry
with stain remover.
Pour the stain remover into
compartment
will be added in the appropriate
phase of the washing programme.
This option can increase
the programme duration.
This option is not
available with a
temperature lower than
40 °C.
• Prewash
Use this option to add a prewash
phase at 30 °C before the washing
phase.
This option is recommended for
heavily soiled laundry, especially if
containing sand, dust , mud and other
solid particles.
This option can increase
the programme duration.
. The stain remover
These two options cannot
be set together.
6.6 Delay Start
With this option you can delay the start
of a programme in a more convenient
.
time.
Tap on the button repeatedly to set the
required delay. The time increases by
steps of 30 minutes up to 90' and from 2
hours up to 20 h.
After starting the cycle by the means of
the Start/Pause button, the display shows
the selected delay time and the
appliance begins the countdown.
6.7 Quick Wash
With this option you can decrease the
programme duration.
• If your laundry is normally or lightly
soiled, it may be advisable to shorten
the washing programme. Touch this
button once to decrease the duration.
• In case of smaller load, touch this
button twice to set an extra quick
programme.
On the display the programme duration
is adjusted accordingly.
When this button is set, the led above
the button is on.
This option can also be used
to shorten the Steam
programme duration.
6.8 Anti-crease
This option adds a short anti-crease
phase at the end of the programme.
This phase reduces fabric creasing and
facilitates the fabric ironing.
When this option is set, the led above
the button is on and then blinks during
anti-crease phase.
This option can increase the
programme duration.
By touching any button the anti-crease
movements stop and the door unlocks.
ENGLISH 17
6.9 Time Drying
Touch this button to set the time that
suits the fabrics you have to dry (refer to
"Timed drying" table). The display shows
the set value.
Each time you touch this button the time
value increases by 5 minutes.
You cannot set all time
values for different types of
fabrics.
6.10 Auto Drying
Touch this button to set one of 3
automatic dryness levels proposed by
the appliance.
On the display the relevant dryness
indicator goes on:
• Iron dry: laundry to be
ironed.
•
put in store.
Cupboard dry: laundry to be
7. PROGRAMMES
7.1 Programme Chart
• Extra dry: laundry to be
fully dried.
You can not set all
automatic levels for each
type of fabrics.
6.11 Mode
Thanks to this button, a cycle can
perform:
• Only washing : Wash indicator is on.
• Washing and drying : Wash and Dry
indicators are on.
• Only drying : Dry indicator is on.
6.12 Start/Pause
Touch the Start/Pause button to start,
pause the appliance or interrupt a
running programme.
Programme Programme description
Washing programmes
White cotton and coloured cotton. Normal, heavy and light
Cottons
Cottons Eco
Synthetics
Delicates
soil.
White cotton and coloured cotton. Normal, heavy and light
soil.
Cottons energy saving programme. This programme at 60ºC
with a load of 10 kg is the reference programme for data entered in the energy label, in compliance with 96/60/EC Directive. Set this programme to have a good washing results and
decrease the energy consumption. The time of the washing
programme is extended.
Synthetic items or mixed fabric items. Normal soil.
Delicate fabrics such as acrylics, viscose and mixed fabrics
requiring gentler washing. Normal soil.
www.aeg.com18
Programme Programme description
Machine washable wool, hand washable wool and other
Wool/Handwash
fabrics with «hand washing» care symbol1).
Outdoor
Wash&Dry programme
Non Stop 60min
Steam programme
Steam
Additional programmes
Rinse
Do not use fabric softener and make sure that
there is no softener residue in the detergent
dispenser.
Outdoor clothing, technical, sport fabrics, waterproof and
breathable jackets, shell jackets with a removable fleece or
inner insulation.
By performing a combined wash and dry programme, the drying phase also acts as waterrepellent restorer. Make sure that the gar-
ment care label permits tumble drying.
Complete programme composed of a washing phase and of a
drying phase for a small load of mixed fabrics (cotton and synthetic items).
Also, the indicator
Steam programmes
appears on the display.
2)
Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours
and make your laundry softer.
Do not use any detergent. If necessary, remove stains by
washing or using localized stain removal.
Steam programmes do not perform any hygienic cycle.
Do not set a Steam programme with these types of items:
• Items to be washed at a temperature lower than 40°C.
• Items where it is not specified on the care label as being
suitable for tumble drying.
• All items with plastic, metal, wooden parts or alike.
To rinse and spin the laundry. All fabrics, except woollens and
very delicate fabrics. Reduce the spin speed accordingly to the
type of laundry.
ENGLISH 19
Programme Programme description
All fabrics, except woollens and delicate fabrics. To spin the
Spin/Drain
1)
During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
2)
If you set a Steam programme with dried laundry, at the end of the cycle the laundry could be humid.
It is better to expose the items to the fresh air for about 10 minutes to let the humidity dry. When the
programme is completed, quickly remove the laundry from the drum. After a steam cycle, items may be
ironed however with less effort.
laundry and to drain the water in the drum.
Programme temperature, maximum spin speed and maximum load
Programme Default tempera-
ture
Temperature
Reference spin
speed
Spin speed range
Maximum load
range
Washing programmes
Cottons
Cottons Eco
Synthetics
Delicates
Wool/Handwash
Outdoor
Non Stop 60min
Steam
Rinse
Spin/Drain
40 °C
95 °C - Cold
40 °C
60°C - 40 °C
40 °C
60 °C - Cold
40 °C
40 °C - Cold
40 °C
40 °C - Cold
30 °C
40 °C - Cold
30 °C
40 °C - 30 °C
1600 rpm
1600 rpm - 400 rpm
1600 rpm
1600 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
10 kg
10 kg
4 kg
4 kg
1.5 kg
2 kg
1200 rpm 1 kg
1.5 kg
1600 rpm
1600 rpm - 400 rpm
1600 rpm
1600 rpm -
10 kg
10 kg
www.aeg.com20
Programme options compatibility
Options
Spin
Rinse Hold
Quiet
No Spin
Extra Rinse
Prewash
2)
Stains
Delay Start
Programme
Rinse
Cottons
Synthetics
Cottons Eco
Delicates
Wool/Handwash
Outdoor
Steam
Non Stop 60min
■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Spin/Drain
1)
■
Quick Wash
Anti-crease
Time Drying
3)
■ ■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
ENGLISH 21
Programme
Options
Auto Drying
1)
If you set No Spin option, the appliance only drains the water.
2)
This option is not available with temperature lower than 40 °C.
3)
If you set the shortest duration, we recommend that you decrease the load size. It is possible to fully
load the appliance, however the washing results can be less satisfactory.
4)
Iron Dry is not available with this programme.
7.2 Woolmark Apparel Care Blue
Cottons
■
Cottons Eco
4)
■
Delicates
Synthetics
Outdoor
Wool/Handwash
Non Stop 60min
washed according to the instructions
on the garment label and those
issued by the manufacturer of this
Steam
Rinse
washing machine. M1230
• The wool drying cycle of this machine
has been tested and approved by The
Woolmark Company. The cycle is
suitable to dry wool garments which
are labelled "hand wash" provided
that the garments are washed in a
Woolmark endorsed hand washing
cycle and dried according to the
instructions issued by the
manufacturer. M1224
• The wool wash cycle of this machine
has been approved by The Woolmark
Company for the washing of wool
In UK, Eire, Hong Kong and India the
Woolmark symbol is a certification
trademark.
garments labelled as "hand wash"
provided that the products are
Spin/Drain
7.3 Automatic drying
Dryness Level Type of fabric Load
Extra Dry
For towelling materials
Cottons and Linen
(bathrobes, bath towels, etc)
up to 6 kg
www.aeg.com22
Dryness Level Type of fabric Load
Cupboard Dry
1)
For items to be stored
Cottons and Linen
(bathrobes, bath towels, etc)
Synthetics and mixed fab-
up to 6 kg
up to 4 kg
rics
(jumpers, blouses, underwear, household and bed linen)
Delicate fabrics
up to 2 kg
(acrylics, viscose and delicate
mixed fabrics)
Wool items
up to 1 kg
(woollen jumpers)
Outdoor sporting garments
up to 2 kg
(Outdoor clothing, technical,
sport fabrics, waterproof and
breathable jackets, shell jackets)
Iron Dry
Suitable for ironing
1)
Hints for test institute The test performance, in accordance with EN 50229, must be carried out with
a FIRST drying load of the maximum declared drying capacity (load composition according to EN61121)
by setting the AUTOMATIC CUPBOARD DRY for Cottons Eco programme. The SECOND drying load
with the residual load must be tested by setting the AUTOMATIC CUPBOARD DRY for Cottons Eco programme.
Cottons and Linen
(sheets, tablecloths, shirts,
etc)
up to 6 kg
7.4 Timed drying
Dryness Level Type of fabric Load
(kg)
Extra Dry
For towelling
materials
Cottons and Linen
(bathrobes, bath towels, etc)
Spin
Suggested
spee
duration
d
(mins)
(rpm)
6 1600 245 - 265
4 1600 165 - 185
2 1600 125 - 135
ENGLISH 23
Dryness Level Type of fabric Load
(kg)
Cupboard Dry
For items to be
stored
Iron Dry
Suitable for
ironing
Cottons and Linen
(bathrobes, bath towels, etc)
Synthetics and mixed fabrics
(jumpers, blouses, underwear, household and bed linen)
Delicates
(acrylics, viscose and delicate mixed
fabrics)
Wool
(woollen jumpers)
Outdoor sporting garments
(Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets,
shell jackets)
Cottons and Linen
(sheets, tablecloths, shirts, etc)
6 1600 235 - 255
4 1600 155 - 175
2 1600 115 - 125
4 1200 135 - 145
1 1200 40 - 50
2 1200 150
1 1200 110 - 130
2 1200 160
6 1600 170 - 190
4 1600 105 - 125
2 1600 75 - 85
Spin
spee
d
(rpm)
Suggested
duration
(mins)
8. BEFORE FIRST USE
During installation or before
first use you may observe
some water in the appliance.
This is a residual water left in
the appliance after a full
functional test in the factory
to ensure the appliance is
delivered to customers in
perfect working order and is
no cause for concern.
1. Make sure that all transit bolts have
been removed from the appliance.
2. Make sure that the electrical power is
available and the water tap is open.
3. Pour 2 litres of water into the
detergent compartment marked by
.
This action activates the drain system.
4. Pour a small quantity of detergent
into the compartment marked by
.
5. Set and start a programme for cotton
at the highest temperature without
any laundry in the drum.
This removes all possible dirt from the
drum and the tub.
www.aeg.com24
9. SETTINGS
9.1 Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option,
touch the Stains/Prewash and the
Delay Start buttons simultaneously
until the indicator
off on the display.
You can activate this option:
• After you touch the Start/Pause
button: all the buttons and the
programme dial are deactivated
(except On/Off button ).
• Before you touch the Start/Pause
button: the appliance cannot start.
The appliance keeps the selection of this
option after you switch it off.
comes on/goes
9.2 Acoustic signals
This appliance is provided with different
acoustic signals, that operate when:
• You activate the appliance (special
short tune).
• You deactivate the appliance (special
short tune).
• You touch the buttons (click sound).
• You make a wrong selection (3 short
sounds).
• The programme is completed
(sequence of sounds for about 2
minutes).
• The appliance has a malfunction
(sequence of short sounds for about 5
minutes).
To deactivate/activate the acoustic
signals when the programme is
completed, touch the Delay Start and
the Quick Wash buttons simultaneously
for about 6 seconds.
If you deactivate the
acoustic signals, they
continue operate when the
appliance has a malfunction.
9.3 Permanent Extra Rinse
With this option you can permanently
have one or two extra rinses when you
set a new programme.
• Simultaneously touch the Temp.
button and the Spin button once to
add one extra rinse.
the display.
• Simultaneously touch the Temp.
button and the Spin button twice to
add two extra rinses.
the display.
• Simultaneously touch the Temp.
button and the Spin button three
times to remove extra rinses. The
display only shows
appears on
appears on
.
10. DAILY USE
WARNING!
Refer to Safety chapters.
10.1 Using weight sensors
For a correct use of the
weight sensor, the drum
must be empty when
activating the appliance.
Set the programme BEFORE
you put the laundry in the
drum.
10.2 Before activating the
appliance
1. Make sure that the mains plug is
connected to the mains socket.
2. Make sure that the water tap is open.
10.3 Activating the appliance
and setting a programme
1. Press button On/Off for a few
seconds to activate the appliance.
The programme dial is automatically set
on cotton programme and only the Wash
indicator is on.
ENGLISH 25
The indicator of Start/Pause button
flashes.
2. Turn the programme knob to the
necessary programme.
The programme indicator comes on.
The display shows the maximum load,
the default temperature, the maximum
spin speed, the indicators of the phases
making up the programme and the
programme duration.
3. If it is necessary, touch the Temp.
button and the Spin button to
change the water temperature and
the spin speed.
4. If necessary, touch the related
buttons to add some options and/or
to set a delayed start.
The display shows the symbol of the set
option and/or the digit shows the
delayed time.
10.4 Loading the laundry
1. Open the appliance door.
The display shows
2. Shake the items before you put them
in the drum. Put the laundry in the
drum, one item at time.
On the display the weight of the laundry
is updated by steps of kg 0.5 and the
programme duration is updated
accordingly. The weight is indicative and
changes with the type of the laundry.
If you put in the drum more
laundry than the maximum
load, the symbol
flashes for a few seconds
and shows the maximum
recommended load.
You can wash your laundry
anyway, but the water and
energy consumption
increase.
To have the best
consumption and washing
performance remove the
exceeding items.
The overload indication is
shown only in programmes
with a maximum load lower
than the appliance
maximum load.
3. Close the door. Make sure that no
laundry stays between the seal and
.
the door. There is a risk of water
leakage or damage to the laundry.
4. The display shows the percentage of
detergent quantity needed
.
This data is indicative and refers to the
detergent dosage recommended for a
maximum load on the detergent
package.
If you change the washing
programme after closing the
door, the display could show
to indicate a
possible overload: open the
door and remove a few
garments.
10.5 Filling the detergent and additives
Compartment for prewash phase,
soak programme or stain remover.
Compartment for washing phase.
Compartment for liquid additives
(fabric conditioner, starch).
1
2
www.aeg.com26
Maximum level for quantity of liquid
additives.
Flap for powder or liquid detergent.
Always follow the
instructions that you find on
the packaging of the
detergent products, but we
recommend that you do not
exceed the maximum
indicated level (
quantity will however
guarantee the best washing
results.
After a washing cycle, if
necessary, remove any
detergent residue from the
detergent dispenser.
). This
10.6 Check the position of the flap
1. Pull out the detergent dispenser until
it stops.
2. Press the lever down to remove the
dispenser.
3. To use powder detergent, turn the
flap up.
4. To use liquid detergent, turn the flap
down.
With the flap in the
position DOWN:
• Do not use
gelatinous or thick
liquid detergents.
• Do not put more
liquid detergent than
the limit shown on
the flap.
• Do not set the
prewash phase.
• Do not set the delay
start function.
5. Measure out the detergent and the
fabric conditioner.
6. Carefully close the detergent
dispenser.
Make sure that the flap does not cause a
blockage when you close the drawer.
10.7 Starting a programme
Touch the Start/Pause button to start the
programme.
The related indicator stops flashing and
stays on.
In the display, the indicator of the
operating phase starts flashing and the
detergent percentage indicator goes off.
The programme starts, the door is
locked. The display shows the indicator
.
The drain pump can operate
shortly before the appliance
fills water.
10.8 Starting a programme with the delay start
1. Touch the Delay Start button
repeatedly until the display shows
the desired delay time. The indicator
comes on.
2. Touch the Start/Pause button.
The appliance starts the countdown of
the delay start.
When the countdown is completed, the
programme starts.
The PROSENSE estimation
starts at the end of the
countdown.
Cancelling the delay start after the countdown has started
To cancel the delay start:
ENGLISH 27
1. Touch the Start/Pause button to
pause the appliance. The related
indicator flashes.
2. Touch the Delay Start button
repeatedly until the display shows
3. Touch the Start/Pause button again
to start the programme immediately.
Changing the delay start after the countdown has started
To change the delay start:
1. Touch the Start/Pause button to
pause the appliance. The related
indicator flashes.
2. Touch the Delay Start button
repeatedly until the display shows
the desired delay time.
3. Touch the Start/Pause button again
to start the new countdown.
10.9 The ProSense load
detection
After touching the Start/Pause button:
1. The detergent percentage indicator
goes off, the indicator flashes.
2. The ProSense starts the laundry load
detection to calculate the real
programme duration. The time dots
flash.
3. After about 15 minutes the display
shows the new programme duration:
the time dots
The appliance adjusts automatically
the programme duration to the load
to achieve perfect washing results in
the minimum possible time. The
programme duration could increase
or decrease.
The ProSense detection is
carried out with complete
washing programmes only
(no skipping phase
selected).
stop flashing.
10.10 Programme phase
indicators
When the programme starts the indicator
of the running phase flashes and the
other phase indicators are steady on.
.
www.aeg.com28
E.g. the washing or pre wash phase is
running: .
When the phase ends the relevant
indicator stops flashing and is steady on.
The next phase indicator starts flashing.
E.g. the rinse phase is running:
If you select the Steam programme the
steam phase indicator
comes on.
10.11 Interrupting a programme and changing the options
When the programme is running, you
can change only some options:
1. Touch the button Start/Pause.
The related indicator flashes.
2. Change the options. The given
information in the display changes
accordingly.
3. Touch the button Start/Pause again.
The washing programme continues.
10.12 Cancelling a running
programme
1. Press the button On/Off to cancel
the programme and to deactivate
the appliance.
2. Press the button On/Off again to
activate the appliance.
Now, you can set a new washing
programme.
If the ProSense phase is
already carried out and the
water filling is already
started, the new programme
starts without repeating
the ProSense phase. The
water and the detergent are
not drained out in order to
avoid waste.
10.13 Opening the door -
Adding garments
While a programme or the delay start
operates, the appliance door is locked.
If the temperature and level
of the water in the drum are
too high and/or the drum
still rotates you cannot open
the door.
1. Touch the button Start/Pause.
.
In the display the related door lock
indicator goes off.
2. Open the appliance door. If
necessary, add or remove the items.
3. Close the door and touch the button
Start/Pause.
The programme or the delay start
continues.
4. The door can be opened when the
programme is complete, or set Spin/
Drain programme and than press
Start/Pause button.
10.14 End of the programme
When the programme has finished, the
appliance stops automatically. The
acoustic signals operate (if they are
active).
In the display all washing phase
indicators become steady and the time
area shows
The indicator of the Start/Pause button
goes off.
The door unlocks and the indicator
goes off.
1. Press the On/Off button to
deactivate the appliance.
After five minutes from the end of the
programme, the energy saving function
automatically deactivates the appliance.
2. Remove the laundry from the
appliance.
3. Make sure that the drum is empty.
4. Keep the door and the detergent
dispenser slightly ajar to prevent
mildew and odours.
.
When you activate the
appliance again, the display
show the end of the last
selected programme. Turn
the programme dial to set a
new cycle.
ENGLISH 29
5. Close the water tap.
10.15 Draining water out after
end of cycle
If you have chosen a programme or an
option that does not empty out the
water of the last rinse, the programme is
completed, but:
• The display shows the indicator
option indicator
door locked indicator
indicator of the running phase
flashes.
• The drum still turns at regular intervals
to prevent the creases in the laundry.
• The door stays locked.
• You must drain the water to open the
door:
1. If necessary, touch the Spin button to
decrease the spin speed proposed
by the appliance.
2. Touch the Start/Pause button:
• If you have set
drains the water and spins.
• If you have set
only drains the water.
The option indicator
while the indicator
goes off.
3. When the programme is completed
and the door locked indicator
goes off, you can open the door.
or and the
, the appliance
, the appliance
or goes out,
flashes and then
, the
. The
4. Press the On/Off button a few
seconds to deactivate the appliance.
In any case, the appliance
empties the water out
automatically after
approximately 18 hours.
10.16 Stand-by option
The Stand-by function automatically
deactivates the appliance to decrease
the energy consumption when:
• You do not use the appliance for 5
minutes before you touch the Start/
Pause button.
Press the button On/Off to activate
the appliance again.
• After 5 minutes from the end of the
washing programme
Press the On/Off button to activate
the appliance again.
The display shows the end of the last
set programme.
Turn the programme dial to set a new
cycle.
If you set a programme or an
option that ends with water
in the drum, the Stand-by
function doesn't deactivate
the appliance to remind you
to drain the water.
11. DAILY USE - WASHING & DRYING
WARNING!
Refer to Safety chapters.
This appliance is an
automatic washer dryer.
11.1 Complete wash&dry
programmes
Automatic Non-Stop programme
The appliance is equipped with the Non
Stop 60min programme, an automatic
wash&dry programme where it is not
necessary to set the Dry mode.
To run this programme:
www.aeg.com30
1. After loading laundry and detergent,
press the On/Off button for some
seconds to activate the appliance.
2. Set the Non Stop 60minprogramme
by means of the programme dial.
The indicator
3. Touch the Start/Pause button to start
the programme.
appears on the display
Non-automatic wash&dry programmes
In some washing programmes, you can
combine Wash and Dry mode for
running a complete wash&dry
programme.
Proceed as follows:
1. Press the On/Off button for some
seconds to activate the appliance.
2. Turn the programme dial to the
desired washing programme. The
display shows the default
temperature and spin. If necessary,
change them according to your
laundry. The display also shows the
maximum recommended load for
washing phase.
3. Set the desired options, if there are
available.
4. Touch the Mode button once to
activate also the drying function. The
Wash and Dry indicators come on.
The indicators
appear on the display. The display
also shows the maximum
recommended load for a washing
and drying programme (e.g. 6 kg for
cottons).
5. Open the door and load the laundry
one item at a time. On the display
the weight of the laundry is updated
by steps of kg 0.5 and the
programme duration is updated
accordingly.
6. Close the door.
7. Put the detergent and the additives
in the appropriate compartment.
When drying a large laundry
load, make sure that the
garments are not rolled up
and that are uniformly
distributed in the drum.
and
11.2 Washing and Drying Automatic levels
1. Tap on the Auto Drying button
repeatedly until the display shows
the required dryness level. The
indicators in the display illuminate
accordingly:
a.
items;
b.
cotton and synthetic items;
c.
items.
The time value on the display is the
duration of both cycles washing and
drying.
To have a good drying by
using less energy and in a
shorter time, the appliance
does not let you set a too
low spin speed for the items
to be washed and dried.
2. Touch button Start/Pause to start the
programme. The PROSENSE
estimation starts.
In the display the door locked
indicator goes on, the indicator of the
running phase starts flashing.
The display also shows the remaining
programme time.
Iron dry: for cotton
Cupboard dry: for
Extra dry: for cotton
11.3 Washing and Timed
Drying
1. Tap on the button Time Drying
repeatedly to set the desired time
value (see the "Timed drying" table
the "Programmes" chapter). The
drying level indicator goes off and
the indicator
Each time you tap on this button the
time value increases by 5 minutes. The
display shows the set new time value.
2. Touch the Start/Pause to start the
programme. The PROSENSE
estimation starts.
In the display the door locked
indicator comes on and the indicator of
the running phase starts flashing.
comes on.
ENGLISH 31
The display also shows the remaining
programme time.
11.4 At the end of the drying programme
• The appliance stops automatically.
• The acoustic signals operate (if they
are active).
• In the display
• The indicator of button Start/Pause
goes off. The door locked
off
• Press the button On/Off for some
seconds to deactivate the appliance.
comes on.
goes
12. DAILY USE - DRYING ONLY
WARNING!
Refer to Safety chapters.
This appliance is an
automatic washer dryer.
12.1 Preparation to drying
1. Press the On/Off button for some
seconds to activate the appliance.
With a drying-only
programme the display does
not show the laundry weight
and the PROSENSE
estimation is deactivated.
2. Load the laundry one item at a time.
3. Turn the programme dial to the
programme suitable for the items to
dry.
4. Tap on the Mode button twice to
exclude washing and perform drying
only. The Dry indicator is on. The
indicators
the display.
When drying a big amount
of laundry, to have good
drying performances, make
sure that the laundry itself is
not rolled up and that is
uniformly distributed in the
drum.
and appear on
After some minutes from
the end of the
programme, the energy
saving function
deactivates the appliance
automatically.
1. Remove the laundry from the
appliance.
2. Make sure that the drum is empty.
After drying phase, clean the
drum, the seal and the inside
of the door with a wet cloth.
12.2 Drying - Automatic levels
1. Tap on the Auto Drying button
repeatedly until the display shows
the required dryness level. The
indicators in the display illuminate
accordingly:
a. Iron dry: for cotton
items;
b.
cotton and synthetic items;
c.
items.
The display shows the drying
programme duration.
2. Touch button Start/Pause to start the
programme.
In the display the door locked
indicator goes on, the indicator of the
running phase starts flashing.
The display also shows the remaining
programme time.
Cupboard dry: for
Extra dry: for cotton
To have a good drying by
using less energy and in a
shorter time, the appliance
does not let you set a too
low spin speed for the items
to be washed and dried.
12.3 Timed Drying
1. Tap on the button Time Drying
repeatedly to set the desired time
www.aeg.com32
value (see the "Timed drying" table
the "Programmes" chapter). The
drying level indicator goes off and
the indicator
Each time you tap on this button the
time value increases by 5 minutes. The
display shows the set new time value.
2. Touch the Start/Pause to start the
programme.
In the display the door locked
indicator comes on and the indicator of
the running phase starts flashing.
The display also shows the remaining
programme time.
comes on.
12.4 At the end of the drying programme
• The appliance stops automatically.
• The acoustic signals operate (if they
are active).
13. FLUFF IN THE FABRICS
During the washing and/or drying phase,
some types of fabric, (sponge, wool,
sweatshirt) could release fluff.
The released fluff could stick to the
fabrics during the next cycle.
This inconvenient increases with
technical fabrics.
To prevent the fluff in your laundry, we
recommend that you:
• To do not wash dark fabrics after you
washed and dried light coloured
fabrics (hand towel, wool, sweatshirt )
and the contrary.
• To dry this type of fabrics at open air
when they are washed the first time.
• To clean the drain filter.
• After the drying phase, clean the
empty drum, the gasket and the door
with a wet cloth.
• In the display
• The indicator of button Start/Pause
goes off. The door locked
off
• Press the button On/Off for some
seconds to deactivate the appliance.
After some minutes from
the end of the
programme, the energy
saving function
deactivates the appliance
automatically.
1. Remove the laundry from the
appliance.
2. Make sure that the drum is empty.
After drying phase, clean the
drum, the seal and the inside
of the door with a wet cloth.
To remove the fluff inside the drum,
set a special programme:
• Empty the drum.
• Clean the drum, the gasket and the
door with a wet cloth.
• Set the rinse programme.
• Simultaneously press the Stains/
Prewash and the Anti-crease buttons
until the display shows CLE to activate
the cleaning function.
• Touch the Start/Pause button to start
the programme.
If the appliance is frequently
used, carry out the CLE
programme regularly.
comes on.
goes
14. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
14.1 The laundry load
• Divide the laundry into: white,
coloured, synthetics, delicates and
wool.
• Follow the washing instructions on the
laundry care labels.
ENGLISH 33
• Do not wash white and coloured
items together.
• Some coloured items can discolour
with the first wash. We recommend
that you wash them separately for the
first couple of times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty pockets and unfold.
• Turn multilayered fabrics, wool and
items with printed illustrations inside
out.
• Pre-treat tough stains.
• Wash heavy soil stains with a special
detergent.
• Be careful with curtains. Remove the
hooks and put the curtains in a
washing bag or pillowcase.
• Do not wash laundry without hems or
with cuts.
• Use a washing bag to wash small
and/or delicate items (e.g. underwired
bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase leading
to excessive vibration. If this occurs:
a. interrupt the programme and
open the door (refer to "Daily
Use" chapter);
b. manually redistribute the load so
that the items are spaced evenly
around the tub;
c. press the Start/Pause button. The
spin phase continues.
14.2 Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is
applicable to the type of stain and fabric.
14.3 Detergents and other
treatments
• Only use detergents and other
treatments specially made for
washing machines:
– powder detergents for all types of
fabric, excluding delicate. Prefer
powder detergents containing
bleach for whites and laundry
sanitization
– liquid detergents, preferably for
low temperature wash
programmes (60 °C max) for all
types of fabric, or special ones for
woollens only.
• Do not mix different types of
detergents.
• To help the environment, do not use
more than the recommended quantity
of detergent.
• Follow the instructions that you find
on packaging of the detergents or
other treatments without exceeding
the indicated maximum level (
• Use the recommended detergents for
the type and colour of the fabric, the
programme temperature and the
level of soil.
14.4 Ecological hints
• Set a programme without the
prewash phase to wash laundry with
normal soil.
• Always start a washing programme
with the maximum load of laundry
allowed.
• If you pre-treat the stains or use a
stain remover, set a programme with
a low temperature.
• To use the correct quantity of
detergent, check the water hardness
of your domestic system. Refer to
"Water hardness".
14.5 Water hardness
If the water hardness in your area is high
or moderate, we recommend that you
use a water softener for washing
machines. In areas where the water
hardness is soft it is not necessary to use
a water softener.
To find out the water hardness in your
area, contact your local water authority.
Use the correct quantity of water
softener. Follow the instructions that you
find on the packaging of the product.
14.6 Prepare the drying cycle
• Open the water tap.
).
www.aeg.com34
• Check if the drain hose is connected
properly. Refer to installation chapter
for more information.
• For the maximum laundry load of the
drying programmes, refer to the
drying programmes table.
14.7 Items not suitable for
drying
Do not set a drying programme for
this laundry:
• Synthetic curtains.
• Pieces of clothing with metal inserts.
• Nylon stockings.
• Quilts.
• Bed covers.
• Duvets.
• Anoraks.
• Sleeping bags.
• Fabrics with residue of hair sprays, nail
solvents or similar.
• Garments with foam-rubber or
materials similar to foam-rubber.
14.8 Garment labels
When you dry the laundry, obey the
indications on the labels of the
manufacturers:
•
= The item can be tumble dried
= The drying cycle is at high
•
temperature
•
= The drying cycle is at reduced
temperature
= The item can not be tumble
•
dried.
14.9 Drying cycle duration
The drying time can change depending
on:
• speed of the last spin
• dryness level
• type of laundry
• weight of the load
14.10 Additional drying
If, at the end of the drying programme,
the laundry is still damp, set a short
drying cycle again.
WARNING!
To avoid creasing and
shrinkage do not overdry
the laundry.
14.11 General Tips
Refer to the «Drying programmes» table
to find the average drying times.
Experience will help you to dry the
laundry better. Take note of the duration
of the cycles done before.
To avoid the static charge at the end of
the drying cycle:
1. Use fabric conditioner in the washing
cycle.
2. Use special fabric conditioner for
tumble dryers.
When the drying programme is
completed remove the laundry promptly.
15. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
15.1 External cleaning
Clean the appliance with mild soap and
warm water only. Fully dry all the
surfaces.
CAUTION!
Do not use alcohol, solvents
or chemical products.
CAUTION!
Do not clean the metal
surfaces with chlorine-based
detergent.
15.2 Descaling
If the water hardness in your
area is high or moderate, we
recommend that you use a
water descaling product for
washing machines.
1
2
ENGLISH 35
Regularly examine the drum to check for
limescale.
The regular detergents already contain
water softening agents, but we
recommend to run a cycle with empty
drum and a descaling product
occasionally.
Always follow the
instructions that you find on
the packaging of the
product.
15.3 Maintenance wash
The repeated and prolonged use of low
temperature programmes can cause
detergent deposits, fluff residues,
bacterial growth inside the drum and the
tub. This could generate bad odours and
mildew.
To eliminate these deposits and
hygienize the inner part of the appliance,
run a maintenance wash regularly (at
least once a month):
1. Remove all laundry from the drum.
2. Run a cotton programme with the
highest temperature with a small
quantity of powder detergent.
Always follow the
instructions that you find on
the packaging of the
product.
2. Run a short cotton programme at
high temperature with empty drum
and with a small quantity of powder
detergent, in order to rinse out any
residues left .
15.6 Cleaning the detergent
dispenser
To prevent possible deposits of dried
detergent or clotted fabric softener
and/or formation of mould in the
detergent dispenser drawer, once in a
while carry out the following cleaning
procedure:
1. Open the drawer. Press the catch
downwards as indicated in the
picture and pull it out.
15.4 Door seal
Regularly examine the seal and remove
all objects from the inner part.
15.5 Cleaning the drum
Regularly examine the drum to prevent
rust forming.
For a complete cleaning:
1. Clean the drum with special products
for stainless steel.
2. Remove the top part of the additive
compartment to aid cleaning and
flush it out under running warm
water, to remove any traces of
accumulated detergent. After
cleaning, replace the top part in its
position.
1
2
www.aeg.com36
3. Make sure that all detergent residue
is removed from the upper and lower
part of the recess. Use a small brush
to clean the recess.
4. Insert the detergent drawer into the
guide rails and close it. Run the
rinsing programme without any
clothes in the drum.
WARNING!
• Do not remove the filter
while the appliance
operates.
• Do not clean the pump if
the water in the
appliance is hot. Wait
until the water cools
down
Proceed as follows to clean the pump:
1. Open the pump cover.
2. Place a suitable bowl below the drain
pump access to collect the water that
flows out.
3. Open the chute downwards. Always
keep a rag nearby to dry up any
water spillages when removing the
filter.
15.7 Cleaning the drain pump
WARNING!
Disconnect the mains plug
from the mains socket.
Regularly check the drain
pump filter and make sure
that it is clean.
Clean the drain pump if:
• The appliance does not drain the
water.
• The drum does not turn.
• The appliance makes an unusual
noise because of the blockage of the
drain pump.
• The display shows the alarm code
.
4. Turn the filter 180 degrees in anticlockwise direction to open it,
without removing. Let the water flow
out.
5. When the bowl is full of water, turn
1
2
2
1
2
1
the filter back and empty the
container.
6. Repeat the steps 4 and 5 until the
water stops to flow out.
7. Turn the filter anti-clockwise to
remove it.
ENGLISH 37
11. Put the filter back into the special
guides by turning it clockwise. Make
sure that you tighten the filter
correctly to prevent leakages.
12. Close the pump cover.
8. If it is necessary, remove fluff and
objects from the filter recess.
9. Make sure that the impeller of the
pump can rotate. If it does not
rotate, contact the Authorised
Service Centre.
When you drain the water with the
emergency drain procedure, you must
activate the drain system again:
a. Put 2 litres of water in the main
wash compartment of the
10. Clean the filter under the water tap.
detergent dispenser.
b. Start the programme to drain the
water.
1
2
3
45°
20°
www.aeg.com38
15.8 Cleaning the inlet hose
and the valve filter
It is recommended to clean both the
filters of the inlet hose and valve
occasionally to remove any deposit,
collected over the time:
1. Remove the inlet hose from the tap
and clean the filter.
2. Remove the inlet hose from the
appliance by loosening the ring nut.
15.9 Emergency drain
If the appliance cannot drain the water,
carry out the same procedure, described
in 'Cleaning the drain pump' paragraph.
If necessary, clean the pump.
When you drain the water with the
emergency drain procedure, you must
activate the drain system again:
1. Put 2 litres of water in the main wash
compartment of the detergent
dispenser.
2. Start the programme to drain the
water.
15.10 Frost precautions
If the appliance is installed in an area
where the temperature can reach the
values around 0° C or drop below,
remove the remaining water from the
inlet hose and the drain pump.
3. Clean the valve filter on the back of
the appliance with a toothbrush.
4. When you reconnect the hose to the
back of the appliance, turn it left or
right (not in vertical position)
depending on the position of your
water tap.
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in
a container and let the water flow out
of the hose.
4. Empty the drain pump. Refer to the
emergency drain procedure.
5. When the drain pump is empty,
install the inlet hose again.
WARNING!
Make sure that the
temperature is higher than 0
°C before you use the
appliance again.
The manufacturer is not
responsible for damages
caused by low temperatures.
16. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
16.1 Introduction
The appliance does not start or it stops
during operation.
First try to find a solution to the problem
(refer to the table). If the problem
persists, contact the Authorised Service
Centre.
In case of major problems, the acoustic
signals operate, the display shows an
alarm code and the Start/Pause button
may flash continuously:
- The appliance does not fill with
•
water properly.
Start the appliance again by pressing
Start/Pause button. After 5 seconds
the door will be unlocked.
•
•
- The appliance does not drain
the water.
- The appliance door is open or
not closed correctly. Please check the
door!
If the appliance is
overloaded, remove
some items from the
drum and/or keep
pressed the door while
touching the Start/Pause
button until the indicator
stops flashing (see
the picture below).
ENGLISH 39
• - The mains supply is unstable.
Wait until the mains supply is stable.
•
- No communication between
electronic elements of the appliance.
Switch it off and switch on again.
The programme was not finished
properly or the appliance stopped
too early. If the alarm code appears
again, contact the Authorised Service
Centre.
•
- The anti-flood device is on.
Disconnect the appliance and close
the water tap. Contact the Authorised
Service Centre.
WARNING!
Deactivate the appliance
before carrying out any
check.
16.2 Possible failures
Problem Possible solution
• Make sure that the mains plug is connected to the mains
socket.
• Make sure that the appliance door is closed.
The programme does
not start.
• Make sure that there is no damaged fuse in the fuse box.
• Make sure that the Start/Pause has been touched.
• If the delay start is set, cancel the setting or wait for the end
of countdown.
• Deactivate the Child Lock function if it is on.
www.aeg.com40
Problem Possible solution
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too
low. For this information, contact your local water authority.
• Make sure that the water tap is not clogged.
The appliance does not
fill with water properly.
• Make sure that the inlet hose has no kinks, damages or
bends.
• Make sure that the connection of the water inlet hose is
correct.
• Make sure that the filter of the inlet hose and the filter of
the valve are not clogged. Refer to 'Care and cleaning'.
The appliance fills with
water and drains immediately
• Make sure that the drain hose is in the correct position. The
hose may be positioned too low. Refer to "Installation instruction".
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the drain filter is not clogged. Clean the fil-
The appliance does not
drain the water.
ter, if necessary. Refer to "Care and cleaning".
• Make sure that the connection of the drain hose is correct.
• Set the drain programme if you set a programme without
drain phase.
• Set the drain programme if you set an option which ends
with water in the tub.
• Set the spin programme.
The spin phase does not
operate or the washing
cycle lasts longer than
usual.
• Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
• Adjust manually the items in the tub and start the spin
phase again. This problem may be caused by balance problems.
• Make sure that the couplings of the water hoses are tight
and there is not water leakages.
There is water on the
floor.
• Make sure that the water inlet hose and the drain hose have
no damages.
• Make sure you use the correct detergent and the correct
quantity of it.
• Make sure that a washing programme that ends with water
in tub, has been selected.
• Make sure that the washing programme is finished.
• Set the drain or the spin programme if there is water in the
You cannot open the appliance door.
drum.
• Make sure that the appliance receives electrical power.
• This problem may be caused by a failure of the appliance.
Contact the Authorised Service Centre.
If you need to open the door, please read carefully "Emergency door opening".
Problem Possible solution
• Make sure the levelling of the appliance is correct. Refer to
The appliance makes an
unusual noise and vibrates.
"Installation instruction".
• Make sure that the packaging and/or the transit bolts are
removed. Refer to "Installation instruction".
• Add more laundry in the drum. The load may be too small.
The programme duration
increases or decreases
during programme execution.
• The ProSense function is able to adjust the programme du-
ration according to the type and the laundry load size. Refer to "The ProSense load detection" in "Daily Use" chapter.
• Increase the detergent quantity or use a different deter-
gent.
The washing results are
not satisfactory.
• Use special products to remove the stubborn stains before
you wash the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
Too much foam in the
• Reduce the quantity of detergent.
drum during the washing
cycle.
After the washing cycle,
there are some detergent residues in the dispenser drawer.
The drum is empty and
the display shows there is
• Make sure that the flap is in the correct position (UP for
powder detergent - DOWN for liquid detergent).
• Make sure you have used the detergent dispenser according the indications given in this user manual.
• Press the On/Off button to deactivate the appliance and
activate it again to set a tare.
some weight in.
• You loaded the laundry before activating the appliance.
The drum is full but the
display shows 0.0 kg.
Press the On/Off button to deactivate the appliance.
• Empty the drum and follow the necessary steps. (Refer to
"Loading the laundry")
• Turn the water tap on.
The appliance does not
dry or does not dry correctly.
• Make sure the drain filter is not clogged.
• Reduce the laundry load.
• Make sure you have set the correct cycle. if necessary, set
again a short drying time.
The fabrics washed in the previous cycle released fluff of a different colour:
The laundry is full of different colours fluff.
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum run the special programme to clean it (refer to “Fluff in the fabrics" for
more details).
ENGLISH 41
www.aeg.com42
After the check, activate the appliance. The programme continues from the point of
interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes. Deactivate and activate the appliance. If the
problem continues, contact the Authorised Service Centre.
16.3 Emergency door opening
In case of power failure or functioning
failure the appliance door remains
locked. The washing programme
continues when the power is restored. If
the door remains locked in case of
failure, it is possible to open it using the
emergency unlock function.
Before opening the door:
CAUTION!
Risk of burns! Make sure
that the water
temperature is not too
high and the laundry is not
hot. If necessary, wait until
they cool down.
CAUTION!
Risk of injury! Make sure
that the drum is not
rotating. If necessary, wait
until the drum stops
rotating.
Make sure that the water
level inside the drum is not
too high. If necessary,
proceed with an
emergency drain (refer to
«Emergency drain» in
«Care and cleaning»
chapter).
To open the door, proceed as follows:
1. Press the On/Off button to switch the
appliance off.
2. Disconnect the mains plug from the
mains socket.
3. Open the filter flap.
4. Pull the emergency unlock trigger
downward once. Pull it downward
once again, keep it tensed and, in
the meanwhile, open the appliance
door.
5. Take out the laundry and then close
the appliance door.
6. Close the filter flap.
17. CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of
laundry and ambient temperature. Water pressure, the supply voltage
and the temperature of inlet water may also affect the washing programme duration.
Technical specifications may be changed without prior notice to improve
the quality of product.
ENGLISH 43
During the washing programme, the ProSense technology can vary the
wash duration and the consumption values. For further details see 'The
ProSense load detection' paragraph in 'Daily Use' chapter.
Programmes Load
Cottons 60°C 10 1.70 85 205
Cottons Eco
Cotton Energy Saving Pro-
gramme 60°C
Cottons 40°C 10 1.30 85 205
Synthetics 40°C 4 0.78 55 130
Delicates 40°C 4 0.60 63 91
Wool/Handwash 30°C 1.5 0.35 57 60
1)
«Cotton Energy Saving programme » at 60°C with a load of 10kg is the reference programme for the
data entered in the energy label, in compliance with 96/60/EC Directive.
1)
18. TECHNICAL DATA
Dimension Width/ Height/ Depth/
Total depth
Electrical connection Voltage
Overall power
Fuse
Frequency
Level of protection against ingress of solid particles
and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture
Water supply
Water supply pressure2)Minimum
1)
Maximum
Energy
(kg)
consumption (kWh)
10 0.92 61 275
Water consumption (litre)
600 mm/ 850 mm/ 630 mm/ 660 mm
230-240 V
2200 W
13 A
50 Hz
IPX4
Cold water
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Approximate programme duration
(minutes)
Maximum wash load Cotton 10 kg
Maximum dry load Cotton
Synthetics
6 kg
4 kg
www.aeg.com44
Spin Speed Maximum spin speed 1550 rpm
1)
Connect the water inlet hose to a water tap with a 3/4'' thread.
2)
The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your
domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
19. ACCESSORIES
19.1 Available in
19.3 Pedestal with the drawer www.aeg.com/shop or from authorised dealer
Only appropriate
accessories approved by
AEG ensure the safety
standards of the appliance. If
unapproved parts are used,
any claims will be
invalidated.
19.2 Fixing plate kit
If you install the appliance on a plinth,
secure the appliance with the fixing
plates.
Read carefully the instructions supplied
with the accessory.
To raise your appliance and make
loading and unloading laundry easier.
The drawer can be used for laundry
storage e.g.: towels, cleaning products
and more.
Read carefully the instructions supplied
with the accessory.
20. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
.
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
*
ENGLISH 45
www.aeg.com46
ENGLISH 47
www.aeg.com/shop
157024390-A-372018
Loading...