Page 1
USER
MANUAL
L7FEE1412N
EN User Manual
Wa织hing Machine
Page 2
www.aeg.com2
CONTENTS
1. SAFETY INFORMATION.............................................................................................
2. SAFETY INSTRUCTIONS.............................................................................................4
3. INSTALLATION............................................................................................................6
4. PRODUCT DESCRIPTION.........................................................................................10
5. CONTROL PANEL..................................................................................................... 11
6. DIAL AND BUTTONS................................................................................................ 13
7. PROGRAMMES..........................................................................................................16
8. SETTINGS...................................................................................................................19
9. BEFORE FIRST USE................................................................................................... 20
10. DAILY USE................................................................................................................20
11. HINTS AND TIPS..................................................................................................... 25
12. CARE AND CLEANING.......................................................................................... 26
13. TROUBLESHOOTING.............................................................................................31
14. TECHNICAL DATA..................................................................................................34
15. ACCESSORIES.........................................................................................................35
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
2
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
SAFETY INFORMATION
1.
Before the installation and use of the appliance,
carefully read the supplied instructions. The
Page 3
ENGLISH 3
manufacturer is not responsible for any injuries or
damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away unless continuously supervised.
• Children of less than 3 years of age should be kept
away unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of
it appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when
the door is open.
• If the appliance has a child safety device, it should be
activated.
• Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
• Do not change the specification of this appliance.
• This appliance is intended to be used in household
and similar applications such as:
– staff kitchen areas in shops, offices and other
working environments;
– by clients in hotels, motels, bed & breakfast and
other residential type environments;
– areas for communal use in blocks of flats or in
launderettes.
Page 4
www.aeg.com4
• Do not exceed the maximum load of 10 kg (refer to
the "Programme chart" chapter).
• The operating water pressure at the water entry point
from the outlet connection must be between 0.5 bar
(0.05 MPa) and 8 bar (0.8 MPa).
• The ventilation opening in the base must not be
covered by a carpet, mat, or any floor covering.
• The appliance must be connected to the water mains
using the new supplied hose sets, or other new hose
sets supplied by the Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must
be replaced by the manufacturer, its Authorised
Service Centre or similarly qualified persons to avoid
an electrical hazard.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
• Do not use high pressure water sprays and/or steam
to clean the appliance.
• Clean the appliance with a moist cloth. Use only
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
2. SAFETY INSTRUCTIONS
2.1 Installation
The installation must comply
with relevant national
regulations.
• Remove all the packaging and the
transit bolts including rubber bush
with plastic spacer.
•
Keep the transit bolts in a safe place.
If the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Do not install or use the appliance
where the temperature can be less
than 0°C or where it is exposed to the
weather.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• When the appliance is in its
permanent position, check if it is
levelled correctly with the aid of a
spirit level. If it is not, adjust the feet
accordingly.
• Do not install the appliance directly
above a floor drain.
Page 5
ENGLISH 5
• Do not spray water on the appliance
and do not expose it to excessive
humidity.
•
Do not install the appliance where the
appliance door cannot be fully
opened.
• Do not put a closed container to
collect possible water leakage under
the appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
2.2 Electrical connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
•
Always use a correctly installed
shockproof socket.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug and to the mains
cable. Should the mains cable need
to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not touch the mains cable or the
mains plug with wet hands.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the
E.E.C. Directives.
2.3 Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes,
pipes not used for a long time, where
repair work has been carried out or
new devices fitted (water meters,
etc.), let the water flow until it is clean
and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• Do not use an extension hose if the
inlet hose is too short. Contact the
Authorised Service Centre for the
replacement of the inlet hose.
• It is possible to see water flowing
from the drain hose. This is due to the
testing of the appliance with the use
of water in the factory.
• You can extend the drain hose to
maximum 400 cm. Contact the
Authorised Service Centre for the
other drain hose and the extension.
2.4 Use
WARNING!
Risk of injury, electric shock,
fire, burns or damage to the
appliance.
• Follow the safety instructions on the
detergent packaging.
•
Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Make sure that all metal objects are
removed from the laundry.
• Do not wash fabrics which are heavily
soiled with oil, grease or other greasy
substances. It can damage rubber
parts of the washing machine.
Prewash such fabrics by hand before
loading them into the washing
machine.
• Do not touch the glass door while a
programme is in operation. The glass
can get hot.
2.5 Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
Page 6
www.aeg.com6
• Remove the door catch to prevent
children or pets from becoming
trapped in the drum.
•
Dispose of the appliance in
accordance with local requirements
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Unpacking
WARNING!
Remove all the packaging
and the transit bolts before
installing the appliance.
WARNING!
Use the gloves.
1. Remove the external film. If
necessary, use a cutter.
for the disposal of Waste Electrical
and Electronic Equipment (WEEE).
4. Open the door and remove the
polystyrene piece from the door seal
and all the items from the drum.
2. Remove the cardboard top and the
polystyrene packaging materials.
3. Remove the internal film.
5. Carefully put the appliance down on
its rear side.
6. Put the front polystyrene packaging
element on the floor under the
appliance.
Make sure not to
damage the hoses.
7. Remove the polystyrene protection
from the bottom.
Page 7
1
2
ENGLISH 7
8. Pull up the appliance in vertical
position.
9. Remove the power supply cable and
the drain hose from the hose holders.
It is possible to see
water flowing from the
drain hose. This is due to
the testing with water of
the appliance in factory.
10. Remove the three bolts by using the
spanner supplied with the appliance.
11. Pull out the plastic spacers.
12. Put the plastic caps, that you find in
the user manual bag, in the holes.
We recommend that you
keep the packaging and the
transit bolts for any
movement of the appliance.
3.2 Positioning and levelling
1. Install the appliance on a flat hard
floor.
Make sure that carpets do
not stop the air circulation
below the appliance.
Make sure that the
appliance does not touch
the wall or other units.
2. Loosen or tighten the feet to adjust
the level.
WARNING!
Do not put cardboard, wood
or equivalent materials
below the appliance feet to
adjust the level.
Page 8
x4
20O20
O
45O45
O
www.aeg.com8
The appliance must be level and stable.
A correct adjustment of the
appliance level prevents the
vibration, noise and the
movement of the appliance
when in operation.
When the machine is
installed on a plinth or if a
washer dryer is stacked on
the washing machine, use
the accessories described in
chapter 'Accessories'. Read
carefully the instructions
supplied with the appliance
and with the accessory.
3.3 The inlet hose
1. Connect the water inlet hose to the
back of the appliance.
2. Position it toward left or right
depending on the position of the
water tap.
Make sure that the inlet hose
is not in vertical position.
3. If necessary, loose the ring nut to set
it in the correct position.
4. Connect the water inlet hose to the
cold water tap with 3/4" thread.
CAUTION!
Make sure that there are no
leaks from the couplings.
Do not use an extension
hose if the inlet hose is too
short. Contact the service
centre for the replacement
of the inlet hose.
3.4 Water-stop device
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing.
The red sector in the window «A» shows
this fault.
Page 9
A
If this occurs, close the water tap and
contact the authorized service centre to
replace the hose.
3.5 Water drainage
The drain hose should be positioned at a
height of not less than 60 cm and not
more than 100 cm from the floor.
You can extend the drain
hose to maximum 400 cm.
Contact the authorized
service centre for the other
drain hose and the
extension.
It is possible to connect the drain hose in
different ways:
1. Make a U shape with the drain hose
and put it around the plastic hose
guide.
ENGLISH 9
Make sure that the drain
hose end is not immersed in
the water. There may be a
return of dirty water into the
appliance.
3. To a stand pipe with vent-hole Insert the drain hose directly into a
drain pipe. Refer to the illustration.
2. On the edge of a sink - Fasten the
guide to the water tap or to the wall.
Make sure that the plastic
guide cannot move when
the appliance drains.
The end of the drain hose
must always be ventilated ,
i.e. the inner diameter of the
drain pipe (min. 38 mm min. 1.5") must be larger
than the external diameter
of the drain hose.
4. If the end of the drain hose looks like
this (see the picture), you can push it
directly into the stand pipe.
Page 10
www.aeg.com10
5. Without the plastic hose guide, to
a sink spigot - Put the drain hose in
the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the drain
hose makes a loop to
prevent particles going into
the appliance from the sink.
4. PRODUCT DESCRIPTION
4.1 Special features
Your new washing machine meets all
modern requirements for an effective
treatment of laundry with low water,
energy and detergent consumption and
proper care of fabric.
• The ProSense technology detects
the laundry load size defining the
programme duration in 30 seconds.
The washing programme is tailored to
the laundry load and the type of fabric
without consuming more time, energy
and water than necessary.
• The steam has a quick and easy way
to refresh the clothes. The gentle
6. Position the hose directly to a builtin drain pipe in the room wall and
tighten it with a clamp.
steam programmes remove odours
and reduce creases in dry fabrics so
they need little ironing.
The 易熨烫 option, finishes every
cycle with gentle steam that relaxes
the fibres and reduces fabric creasing.
Ironing will be easier!
• Thanks to the Soft Plus option, the
fabric softener is uniformly spread out
in the laundry and deeply penetrates
the fabric fibres favouring a perfect
softness.
Page 11
4.2 Appliance overview
1 2 3
9
5
6
7
4
10
8
11 12
2
3
6
12 11 10 8
1
4
5
7
9
ENGLISH 11
Worktop
1
Detergent dispenser
2
Control panel
3
Door handle
4
Rating plate
5
Drain pump filter
6
Feet for levelling the appliance
7
5. CONTROL PANEL
5.1 Control panel description
Drain hose
8
Inlet hose connection
9
Mains cable
10
Transit bolts
11
Hose support
12
Page 12
MIX
www.aeg.com12
Programme dial
1
Display
2
3
Eco touch button (节能)
4
Time saving touch button (省时)
5
Rinse touch button (漂洗)
• Extra rinse option (额外漂洗)
• Skipping wash phase - Only Rinse
option (单漂洗)
Start/Pause touch button (启动/暂停)
6
Stain/Prewash touch button (去污/预
7
洗)
• Stain option (去污)
• Prewash option (预洗)
5.2 Display
8
Delay start touch button (预约)
9
Steam Plus touch button (易熨烫)
10
Spin reduction touch button (脱水)
• Rinse Hold option
• Extra Silent option
• Skipping wash and rinse phases -
Only Spin option (单脱水)
• Skipping wash, rinse and spin
phases - Only Drain option (单排
水)
11
Temperature touch button (温度)
12
On/Off push button (开/关)
Maximum load indicator. The indicator flashes during the laundry
load estimation (refer to ProSense load detection paragraph) .
Maximum laundry indicator. It blinks if the laundry amount exceeds the
declared load.
Door locked indicator.
Delay start indicator.
The digital indicator can show:
• Programme duration (e. g.
• Delay time (e. g.
• Cycle end (
• Warning code (e.g.
Washing phase indicator. It flashes during pre-wash and wash phase.
or ).
).
).
).
Page 13
ENGLISH 13
Rinsing phase indicator. It flashes during rinse phase.
When the Soft Plus option is activated, the indicator appears.
Spinning and draining phase indicator. It flashes during spin and drain
phase.
Steam phase indicator.
Anti-crease phase indicator.
Child safety lock indicator.
Energy saving indicators. The indicator appears by selecting a
programme for cotton at 40 °C or 60 °C.
Time saving indicator.
Spin speed indicator.
Rinse hold indicator.
Extra Silent indicator.
Temperature indicator. The indicator appears when a cold wash is
set.
6. DIAL AND BUTTONS
6.1 开/关
Pressing this button for a few seconds
allows to activate or deactivate the
appliance. Two different tunes sound
while switching the appliance on or off.
As the Stand-by function automatically
deactivates the appliance to decrease
the energy consumption in a few cases,
you may need to activate the appliance
again.
For more details, refer to Stand-by
paragraph in Daily Use chapter.
6.2 Introduction
The options/functions are
not selectable with all
washing programmes. Check
the compatibility between
options/functions and
washing programmes in the
"Programme Chart". An
option/function can exclude
another one, in this case the
appliance doesn't allow you
to set the incompatible
options/functions together.
Make sure the screen and
touch buttons are always
clean and dry.
6.3 温度
When you select a washing programme,
the appliance automatically proposes a
default temperature.
Page 14
www.aeg.com14
Touch this button repeatedly until the
desired temperature value appears on
the display.
When the display shows the indicators
and , the appliance does not
heat the water.
6.4 脱水
When you set a programme, the
appliance automatically sets the
maximum spin speed allowed.
Touch repeatedly this button to:
• Decrease the spin speed.
The display shows only
the spin speeds available
for the set programme.
• Activate the Rinse Hold option.
The final spin is not performed. The
water of the last rinse is not drained
out to prevent the fabrics from
creasing. The washing programme
ends with water in the drum.
The display shows the indicator
The door stays locked and the drum
turns regularly to reduce creasing.
You must drain the water to unlock
the door.
If you touch the 启动/暂停 button, the
appliance performs the spinning
phase and drains the water.
The appliance empties
the water out
automatically after 18
hours approximately.
• Activate the Extra Silent option.
The intermediate and the final
spinning phases are suppressed and
the programme ends with water in the
drum. This helps to reduce creasing.
The display shows the indicator
The door stays locked. The drum
turns regularly to reduce creasing.
You must drain the water to unlock
the door.
As the programme is very quiet, it is
suitable for use at night time when
cheaper electricity tariffs are available.
In some programmes the rinses are
performed with more water.
If you touch the 启动/暂停 button, the
appliance performs the only draining
phase.
The appliance empties
the water out
automatically after 18
hours approximately.
• Activate the drain-only option
(Skipping the wash, rinse and spin
phases): 单排水.
The appliance performs the only
draining phase of the selected
washing programme.
The display shows the indicator
(cold), and the indicator (no
spin) and the indicator
• Activate the spin-only option
(Skipping the wash and rinse
phases): 单脱水.
Before setting this
option, select a suitable
washing programme for
.
the garments. The
appliance will performs
the most fitting spin cycle
for your garments care
(e.g. For synthetics items,
first select the 化纤
washing programme and
then the 单脱水 option).
The appliance performs only the
spinning phase of the selected
washing programme.
The display shows the indicator
(cold), the phase indicator and the
spin speed.
6.5 去污/预洗
Press this button repeatedly to activate
.
one of the two options or both.
The relevant indicator goes on in the
display.
• 去污
Select this option to add an anti-stain
phase to a programme in order to
treat heavily soiled or stained laundry
with stain remover.
Pour the stain remover into
compartment
. The stain remover
.
Page 15
ENGLISH 15
will be added in the appropriate
phase of the washing programme.
This option is not
available with a
temperature lower than
40 °C.
• 预洗
Use this option to add a pre-wash
phase at 30 °C before the washing
phase.
This option is recommended for
heavily soiled laundry, especially if
containing sand, dust , mud and other
solid particles.
The options can increase the
programme duration.
6.6 易熨烫
This option adds a steam phase followed
by a short anti-crease phase at the end
of the washing programme.
The steam phase reduces fabric creasing
and facilitates the fabric ironing.
The indicator
during steam phase.
This option can increase the
programme duration.
When the programme stops the display
shows a zero , the indicator is
steady on and the indicator starts
flashing. The drum performs smooth
movements for about 30 minutes to keep
the steam benefit. By touching any
button the anti-crease movements stop
and the door unlocks.
A small laundry load helps to
reach better results.
flashes on the display
6.7 预约
With this option you can delay the start
of a programme in a more convenient
time.
Touch the button repeatedly to set the
required delay. The time increases by
steps of 30 minutes up to 90' and from 2
hours up to 20 h.
After touching the 启动/暂停 button, the
display shows the indicator
selected delay time and the appliance
begins the countdown.
and the
6.8 漂洗
With this button you can select one of
the following options:
• 额外漂洗 option
This option adds a few rinses
according to the selected washing
programme.
Use this option for persons allergic to
detergent residues and in areas
where the water is soft.
This option increases
slightly the programme
duration.
• Skipping wash phase - 单漂洗 option
The appliance performs only the
rinsing phase , the spinning and the
draining phases of the selected
programme.
The corresponding indicator above the
touch button illuminates.
6.9 省时
With this option you can decrease the
programme duration.
• If your laundry is normally or lightly
soiled, it may be advisable to shorten
the washing programme. Touch this
button once to decrease the duration.
• In case of smaller load, touch this
button twice to set an extra quick
programme.
The display shows the indicator .
This option can also be used
to shorten the 蒸汽
programme duration.
6.10 节能
The 节能 option reduces the energy
consumption maintaining good washing
results.
Set this option for slightly or normally
soiled items washed at 30°C or higher
temperatures.
Page 16
www.aeg.com16
Water and energy consumption may
depend on different causes, such as
water pressure, its hardness and
temperature, ambient temperature, type
and quantity of laundry, the set options,
spin speed and voltage fluctuations in
the electricity network. The display shows
the indicator .
7. PROGRAMMES
7.1 Programme Chart
Washing programmes
Programme Programme description
Washing programmes
棉物
化纤
精
羊毛/手洗
Steam programme
蒸汽
Washing programmes
6.11 启动/暂停
Touch the 启动/暂停 button to start,
pause the appliance or interrupt a
running programme.
White cotton and coloured cotton. Normal, heavy and light
soil.
Cotton Energy saving programme. This programme at 60°C
with a load of 10 kg and 节能 option is the reference programme for the data entered in the energy label, in compliance with GB/T 4288-2008.
Synthetic items or mixed fabric items. Normal soil.
Delicate fabrics such as acrylics, viscose and mixed fabrics
requiring gentler washing. Normal soil.
Machine washable wool, hand washable wool and other
fabrics with «hand washing» care symbol1).
Steam programme for cotton and synthetic items. Steam
can be used for dried2), washed or worn once laundry. This
programme reduce creases and odours3) and relaxes the fibres. When the programme is completed, quickly remove the
laundry from the drum. After a steam programme, ironing becomes effortless. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam
programmes do not perform any hygienic cycle. Do not set a
Steam programme with these types of items:
• Items that are not suitable for tumble drying.
• All items with plastic, metal, wooden parts or alike.
Page 17
Programme Programme description
White cotton items. This programme removes micro-organ-
抗过敏
isms thanks to a washing phase with the temperature maintained above 60°C for several minutes. This helps remove
germs, bacteria, micro-organism and particles. An additional
rinsing phase ensures a proper removal of detergent residues
and pollens/allergenic items. In this way the wash is more effective.
Cotton and synthetic items lightly soiled or once worn.
快洗 20'
ENGLISH 17
户外
there is no softener residue in the detergent
dispenser.
Outdoor clothing, technical, sport fabrics, waterproof and
breathable jackets, shell jackets with a removable fleece or
inner insulation. The recommended laundry load is 2.5 kg.
This programme can also be used as water-repellent restoring
cycle, specifically tailored for treating clothes with a hydrophobic coating. To perform the water-repellent restoring cycle,
proceed as follows:
• Pour the washing detergent in the compartment
• Pour a special water-repellent restorer for fabric in the
drawer compartment for fabric softener .
• Reduce the laundry load to 1 kg.
To further improve the water-repellent restoring action, dry the laundry in a tumble dryer by
setting the 户外 drying programme (if available
and if the garment care label permits tumble
drying).
Single synthetic blanket, padded clothes, duvets, down
Do not use fabric softener and make sure that
羽绒被
jackets and similar items.
Denim clothing and jersey items. Normal soil. This pro-
牛仔
gramme performs a gentle rinsing phase, designed for denim,
that reduces fading and does not cause washing powder residues on the fibres.
1)
During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
2)
If you set a Steam programme with dried laundry, at the end of the cycle the laundry can be humid.
Line dry the items for about 10 minutes.
3)
Steam programme doesn't remove particularly intense odour.
.
Page 18
www.aeg.com18
Programme temperature, maximum spin speed and maximum load
Programme Default tempera-
ture
Maximum spin speed
Spin speed range
Temperature
range
Washing programmes
Maximum load
棉物
化纤
精
羊毛/手洗
Steam programme
蒸汽
Washing programmes
抗过敏
快洗 20'
户外
羽绒被
40 °C
95 °C - Cold
40 °C
60 °C - Cold
40 °C
40 °C - Cold
40 °C
40 °C - Cold
- - 1.5 kg
60 °C
30 °C
40 °C - 30 °C
30 °C
40 °C - Cold
40 °C
60 °C - 30 °C
1400 rpm
1400 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1400 rpm
1400 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
1200 rpm
1200 rpm - 400 rpm
800 rpm
800 rpm - 400 rpm
10 kg
4 kg
4 kg
1.5 kg
10 kg
3 kg
2.5 kg
1 kg
3 kg
1)
2)
40 °C
牛仔
1)
Washing programme.
2)
Washing programme and waterproofing phase.
60 °C - Cold
1200 rpm
1200 rpm - 400 rpm
10 kg
Page 19
7.2 Woolmark Apparel Care - Blue
8. SETTINGS
ENGLISH 19
The wool wash cycle of this machine has been
approved by The Woolmark Company for the
washing of wool garments labelled as «hand
wash» provided that the garments are washed according to the instructions issued by the
manufacturer of this washing machine. Follow
the garment care label for drying and other
laundry instructions. M1230
The Woolmark symbol is a Certification mark
in many countries.
8.1 Introduction
When pressing a key
combination, do not tilt
your fingers downwards .
The sensors of the
underneath buttons are
sensitive and may interfere
with Your choice.
8.2 Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option,
touch the 脱水 and the 去污/预洗
buttons simultaneously until the
indicator
the display.
You can activate this option:
•
After you touch the 启动/暂停 button:
all the buttons and the programme
dial are deactivated (except 开/关
button ).
• Before you touch the 启动/暂停
button: the appliance cannot start.
The appliance keeps the selection of this
option after you switch it off.
comes on/goes off on
8.3 Acoustic signals
This appliance is provided with different
acoustic signals, that operate when:
• You activate the appliance (special
short tune).
• You deactivate the appliance (special
short tune).
• You touch the buttons (click sound).
• You make a wrong selection (3 short
sounds).
• The programme is completed
(sequence of sounds for about 2
minutes).
• The appliance has a malfunction
(sequence of short sounds for about 5
minutes).
To deactivate/activate the acoustic
signals when the programme is
completed, touch the 去污/预洗 and the
预约 buttons simultaneously for about 6
seconds.
If you deactivate the
acoustic signals, they
continue operate when the
appliance has a malfunction.
8.4 Permanent Extra Rinse
With this option you can permanently
have an extra rinse when you set a new
programme.
To activate/deactivate this option
•
touch the 去污/预洗 button and the
漂洗 button simultaneously until the
indicator of the 额外漂洗 button
comes on/goes off.
8.5 Soft Plus
Set the Soft Plus option to optimise the
fabric softener distribution and improve
the fabric softness.
It is suggested when you use the fabric
softener.
Page 20
www.aeg.com20
This option increases slightly
the programme duration.
To activate/deactivate this option touch
the 温度 button and the 脱水 button
9. BEFORE FIRST USE
During installation or before
first use you may observe
some water in the appliance.
This is a residual water left in
the appliance after a full
functional test in the factory
to ensure the appliance is
delivered to customers in
perfect working order and is
no cause for concern.
1. Make sure that all transit bolts have
been removed from the appliance.
2. Make sure that the electrical power is
available and the water tap is open.
10. DAILY USE
WARNING!
Refer to Safety chapters.
simultaneously until the indicator
comes on/goes off above the
indicator.
3. Pour 2 litres of water into the
detergent compartment marked by
.
This action activates the drain system.
4. Pour a small quantity of detergent
into the compartment marked by
.
5. Set and start a programme for cotton
at the highest temperature without
any laundry in the drum.
This removes all possible dirt from the
drum and the tub.
Make sure not to put too much laundry
in the drum.
4. Close the door firmly.
10.1 Activating the appliance
1. Connect the mains plug to the mains
socket.
2. Open the water tap.
3. Press the 开/关 button for a few
seconds to activate the appliance.
A short tune sounds (if activated). The
programme dial is automatically set on
Cotton programme .
The display shows the maximum load,
the default temperature, the maximum
spin speed, the indicators of the phases
making up the programme and the cycle
duration.
10.2 Loading the laundry
1. Open the appliance door.
2. Shake the items before you put them
in the appliance.
3. Put the laundry in the drum, one item
at a time.
CAUTION!
Make sure that no laundry
stays between the seal and
the door. There is a risk of
water leakage or damage to
the laundry.
Page 21
10.3 Filling the detergent and
1
2
additives
Compartment for prewash phase
an soak programme.
Compartment for washing phase.
Compartment for liquid additives
(fabric conditioner, starch).
Maximum level for quantity of
liquid additives.
Compartment for stain remover.
Flap for powder or liquid
detergent.
ENGLISH 21
3. To use powder detergent, turn the
flap up.
Always follow the
instructions that you find on
the packaging of the
detergent products, but we
recommend that you do not
exceed the maximum
indicated level (
quantity will however
guarantee the best washing
results.
After a washing cycle, if
necessary, remove any
detergent residue from the
detergent dispenser.
). This
10.4 Check the position of the flap
1. Pull out the detergent dispenser until
it stops.
2. Press the lever down to remove the
dispenser.
4. To use liquid detergent, turn the flap
down.
Page 22
www.aeg.com22
With the flap in the
position DOWN:
•
Do not use
gelatinous or thick
liquid detergents.
• Do not put more
liquid detergent than
the limit shown on
the flap.
• Do not set the
prewash phase.
• Do not set the delay
start function.
5. Measure out the detergent and the
fabric conditioner.
6. Carefully close the detergent
dispenser.
Make sure that the flap does not cause a
blockage when you close the drawer.
10.5 Setting a programme
1. Turn the programme dial to select
the desired washing programme. The
related programme indicator comes
on.
The indicator of the 启动/暂停 button
flashes.
The display shows the maximum
declared load for the programme, the
default temperature, the maximum spin
speed, the washing phase indicators
(when available) and an indicative
programme duration.
2. To change the temperature and/or
the spin speed, touch the related
buttons.
3. If desired, set one or more options
by touching the related buttons. The
related indicators come on in the
display and the given information
changes accordingly.
In case a selection is not
possible, no indicator comes
on and an acoustic signal
sounds.
10.6 Starting a programme
Touch the 启动/暂停 button to start the
programme.
The related indicator stops flashing and
stays on.
In the display, the indicator of the
operating phase starts flashing and the
maximum load indicator goes off.
The programme starts, the door is
locked. The display shows the indicator
.
The drain pump can operate
shortly before the appliance
fills water.
10.7 Starting a programme with the delay start
1. Touch the 预约 button repeatedly
until the display shows the desired
delay time. The indicator
on.
2. Touch the 启动/暂停 button.
The appliance starts the countdown of
the delay start.
When the countdown is completed, the
programme starts.
The PROSENSE estimation
starts at the end of the
countdown.
goes
Cancelling the delay start after the countdown has started
To cancel the delay start:
1. Touch the 启动/暂停 button to pause
the appliance. The related indicator
flashes.
2. Touch the 预约 button repeatedly
until the display shows
3. Touch the 启动/暂停 button again to
start the programme immediately.
.
Page 23
ENGLISH 23
Changing the delay start after the countdown has started
To change the delay start:
1. Touch the 启动/暂停 button to pause
the appliance. The related indicator
flashes.
2. Touch the 预约 button repeatedly
until the display shows the desired
delay time.
3. Touch the 启动/暂停 button again to
start the new countdown.
10.8 The ProSense load detection
The programme duration in
the display is referred to a
medium/high load.
After touching the 启动/暂停 button, the
maximum declared load indicator goes
off, the indicator
ProSense starts the laundry load
detection:
1. The appliance detects the load in the
first 30 seconds: the indicator
the time dots
rotates shortly.
2. At the end of the load detection, the
indicator
dots
stop flashing. The programme
duration will be adjusted accordingly
and could increase or decrease. After
further 30 seconds, the water filling
starts.
At the end of the load detection, in case
of drum overload, the indicator is
flashing in the display:
In this case, for 30 seconds, it is possible
to pause the appliance and remove the
exceeding garments.
Once removed the exceeding garments,
touch the 启动/暂停 button to start the
programme again. The ProSense phase
can be repeated up to three times (see
point 1).
Important! If the laundry amount will not
be reduced, the washing programme
starts anyway, despite the overload. In
flashes, the
and
flash, the drum
goes off and the time
this case, it will be not possible to
guarantee the best washing results.
About 20 minutes after the
programme start, the
programme duration could
be adjusted again
depending on the capacity
of water absorption of the
fabrics.
The ProSense detection is
carried out with complete
washing programmes only
(no skipping phase
selected).
10.9 Programme phase indicators
When the programme starts the indicator
of the running phase flashes and the
other phase indicators are steady on.
E.g. the washing or pre wash phase is
running: .
When the phase ends the relevant
indicator stops flashing and is steady on.
The next phase indicator starts flashing.
E.g. the rinse phase is running:
If you select the 易熨烫 the steam phase
indicators come on.
The steam phase is running:
The anti-crease phase is running:
.
.
.
10.10 Interrupting a programme and changing the options
When the programme is running, you
can change only some options:
1. Touch the button 启动/暂停.
The related indicator flashes.
2. Change the options. The given
information in the display changes
accordingly.
3. Touch the button 启动/暂停 again.
Page 24
www.aeg.com24
The washing programme continues.
10.11 Cancelling a running programme
1. Press the button 开/关 to cancel the
programme and to deactivate the
appliance.
2. Press the button 开/关 again to
activate the appliance.
Now, you can set a new washing
programme.
If the ProSense phase is
already carried out and the
water filling is already
started, the new programme
starts without repeating
the ProSense phase. The
water and the detergent are
not drained out in order to
avoid waste. The display
shows the maximum
duration of the programme,
updating it about 20 minutes
after the starting of the new
programme.
10.12 Opening the door Adding garments
While a programme or the delay start
operates, the appliance door is locked.
If the temperature and level
of the water in the drum are
too high and/or the drum
still rotates you cannot open
the door.
1. Touch the button 启动/暂停.
In the display the related door lock
indicator goes off.
2. Open the appliance door. If
necessary, add or remove the items.
3. Close the door and touch the button
启动/暂停.
The programme or the delay start
continues.
4. The door can be opened when the
programme is complete, or set Spin
Drain programme and than press 启
动/暂停 button.
10.13 End of the programme
When the programme has finished, the
appliance stops automatically. The
acoustic signals operate (if they are
active).
In the display all washing phase
indicators become steady and the time
area shows
The indicator of the 启动/暂停 button
goes off.
The door unlocks and the indicator
goes off.
1. Press the 开/关 button to deactivate
the appliance.
After five minutes from the end of the
programme, the energy saving function
automatically deactivates the appliance.
2. Remove the laundry from the
appliance.
3. Make sure that the drum is empty.
4. Keep the door and the detergent
dispenser slightly ajar to prevent
mildew and odours.
5. Close the water tap.
.
When you activate the
appliance again, the display
show the end of the last
selected programme. Turn
the programme dial to set a
new cycle.
10.14 Draining water out after end of cycle
If you have chosen a programme or an
option that does not empty out the
water of the last rinse, the programme is
completed, but:
• The display shows the indicator
option indicator
door locked indicator
indicator of the running phase
flashes.
• The drum still turns at regular intervals
to prevent the creases in the laundry.
• The door stays locked.
• You must drain the water to open the
door:
or and the
, the
. The
Page 25
ENGLISH 25
1. If necessary, touch the 脱水 button to
decrease the spin speed proposed
by the appliance.
2. Touch the 启动/暂停 button:
• If you have set
drains the water and spins.
•
If you have set
only drains the water.
The option indicator
while the indicator
goes off.
3. When the programme is completed
and the door locked indicator
goes off, you can open the door.
4. Press the 开/关 button a few seconds
to deactivate the appliance.
In any case, the appliance
empties the water out
automatically after
approximately 18 hours.
flashes and then
10.15 Stand-by option
The Stand-by function automatically
deactivates the appliance to decrease
the energy consumption when:
11. HINTS AND TIPS
, the appliance
, the appliance
or goes out,
• You do not use the appliance for 5
minutes before you touch the 启动/暂
停 button.
Press the button 开/关 to activate the
appliance again.
•
After 5 minutes from the end of the
washing programme
Press the 开/关 button to activate the
appliance again.
The display shows the end of the last
set programme.
Turn the programme dial to set a new
cycle.
If you set a programme or an
option that ends with water
in the drum, the Stand-by
function doesn't deactivate
the appliance to remind you
to drain the water.
WARNING!
Refer to Safety chapters.
11.1 The laundry load
• Divide the laundry into: white,
coloured, synthetics, delicates and
wool.
Follow the washing instructions on the
•
laundry care labels.
• Do not wash white and coloured
items together.
• Some coloured items can discolour
with the first wash. We recommend
that you wash them separately for the
first couple of times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty pockets and unfold.
• Turn multilayered fabrics, wool and
items with printed illustrations inside
out.
• Pre-treat tough stains.
• Wash heavy soil stains with a special
detergent.
• Be careful with curtains. Remove the
hooks and put the curtains in a
washing bag or pillowcase.
• Do not wash laundry without hems or
with cuts.
• Use a washing bag to wash small
and/or delicate items (e.g. underwired
bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase leading
to excessive vibration. If this occurs:
a. interrupt the programme and
open the door (refer to "Daily
Use" chapter);
b. manually redistribute the load so
that the items are spaced evenly
around the tub;
c. press the 启动/暂停 button. The
spin phase continues.
Page 26
www.aeg.com26
11.2 Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is
applicable to the type of stain and fabric.
11.3 Detergents and other treatments
• Only use detergents and other
treatments specially made for
washing machines:
– powder detergents for all types of
fabric, excluding delicate. Prefer
powder detergents containing
bleach for whites and laundry
sanitization
– liquid detergents, preferably for
low temperature wash
programmes (60 °C max) for all
types of fabric, or special ones for
woollens only.
• Do not mix different types of
detergents.
• To help the environment, do not use
more than the recommended quantity
of detergent.
• Follow the instructions that you find
on packaging of the detergents or
other treatments without exceeding
the indicated maximum level (
• Use the recommended detergents for
the type and colour of the fabric, the
programme temperature and the
level of soil.
11.4 Ecological hints
• Set a programme without the
prewash phase to wash laundry with
normal soil.
• Always start a washing programme
with the maximum load of laundry
allowed.
• If you pre-treat the stains or use a
stain remover, set a programme with
a low temperature.
• To use the correct quantity of
detergent, check the water hardness
of your domestic system. Refer to
"Water hardness".
11.5 Water hardness
If the water hardness in your area is high
or moderate, we recommend that you
use a water softener for washing
machines. In areas where the water
hardness is soft it is not necessary to use
a water softener.
To find out the water hardness in your
area, contact your local water authority.
Use the correct quantity of water
softener. Follow the instructions that you
find on the packaging of the product.
).
12. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
12.1 External cleaning
Clean the appliance with mild soap and
warm water only. Fully dry all the
surfaces.
CAUTION!
Do not use alcohol, solvents
or chemical products.
CAUTION!
Do not clean the metal
surfaces with chlorine-based
detergent.
12.2 Descaling
If the water hardness in your
area is high or moderate, we
recommend that you use a
water descaling product for
washing machines.
Regularly examine the drum to check for
limescale.
Page 27
1
2
ENGLISH 27
The regular detergents already contain
water softening agents, but we
recommend to run a cycle with empty
drum and a descaling product
occasionally.
Always follow the
instructions that you find on
the packaging of the
product.
12.3 Maintenance wash
The repeated and prolonged use of low
temperature programmes can cause
detergent deposits, fluff residues,
bacterial growth inside the drum and the
tub. This could generate bad odours and
mildew.
To eliminate these deposits and
hygienize the inner part of the appliance,
run a maintenance wash regularly (at
least once a month):
1. Remove all laundry from the drum.
2. Run a cotton programme with the
highest temperature with a small
quantity of powder detergent.
12.4 Door seal
Always follow the
instructions that you find on
the packaging of the
product.
2. Run a short cotton programme at
high temperature with empty drum
and with a small quantity of powder
detergent, in order to rinse out any
residues left .
12.6 Cleaning the detergent
dispenser
To prevent possible deposits of dried
detergent or clotted fabric softener
and/or formation of mould in the
detergent dispenser drawer, once in a
while carry out the following cleaning
procedure:
1. Open the drawer. Press the catch
downwards as indicated in the
picture and pull it out.
Regularly examine the seal and remove
all objects from the inner part.
12.5 Cleaning the drum
Regularly examine the drum to prevent
rust forming.
For a complete cleaning:
1. Clean the drum with special products
for stainless steel.
2. Remove the top part of the additive
compartment to aid cleaning and
flush it out under running warm
water, to remove any traces of
accumulated detergent. After
cleaning, replace the top part in its
position.
Page 28
1
2
www.aeg.com28
3. Make sure that all detergent residue
is removed from the upper and lower
part of the recess. Use a small brush
to clean the recess.
4. Insert the detergent drawer into the
guide rails and close it. Run the
rinsing programme without any
clothes in the drum.
WARNING!
• Do not remove the filter
while the appliance
operates.
• Do not clean the pump if
the water in the
appliance is hot. Wait
until the water cools
down
Proceed as follows to clean the pump:
1. Open the pump cover.
2. Place a suitable bowl below the drain
pump access to collect the water that
flows out.
3. Open the chute downwards. Always
keep a rag nearby to dry up any
water spillages when removing the
filter.
12.7 Cleaning the drain pump
WARNING!
Disconnect the mains plug
from the mains socket.
Regularly check the drain
pump filter and make sure
that it is clean.
Clean the drain pump if:
• The appliance does not drain the
water.
• The drum does not turn.
• The appliance makes an unusual
noise because of the blockage of the
drain pump.
• The display shows the alarm code
.
4. Turn the filter 180 degrees in anticlockwise direction to open it,
without removing. Let the water flow
out.
Page 29
5. When the bowl is full of water, turn
1
2
2
1
2
1
the filter back and empty the
container.
6. Repeat the steps 4 and 5 until the
water stops to flow out.
7. Turn the filter anti-clockwise to
remove it.
ENGLISH 29
11. Put the filter back into the special
guides by turning it clockwise. Make
sure that you tighten the filter
correctly to prevent leakages.
12. Close the pump cover.
8. If it is necessary, remove fluff and
objects from the filter recess.
9. Make sure that the impeller of the
pump can rotate. If it does not
rotate, contact the Authorised
Service Centre.
When you drain the water with the
emergency drain procedure, you must
activate the drain system again:
a. Put 2 litres of water in the main
wash compartment of the
10. Clean the filter under the water tap.
detergent dispenser.
b. Start the programme to drain the
water.
Page 30
1
2
3
45°
20°
www.aeg.com30
12.8 Cleaning the inlet hose
and the valve filter
It is recommended to clean both the
filters of the inlet hose and valve
occasionally to remove any deposit,
collected over the time:
1. Remove the inlet hose from the tap
and clean the filter.
2. Remove the inlet hose from the
appliance by loosening the ring nut.
12.9 Emergency drain
If the appliance cannot drain the water,
carry out the same procedure, described
in 'Cleaning the drain pump' paragraph.
If necessary, clean the pump.
When you drain the water with the
emergency drain procedure, you must
activate the drain system again:
1. Put 2 litres of water in the main wash
compartment of the detergent
dispenser.
2. Start the programme to drain the
water.
12.10 Frost precautions
If the appliance is installed in an area
where the temperature can reach the
values around 0° C or drop below,
remove the remaining water from the
inlet hose and the drain pump.
3. Clean the valve filter on the back of
the appliance with a toothbrush.
4. When you reconnect the hose to the
back of the appliance, turn it left or
right (not in vertical position)
depending on the position of your
water tap.
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in
a container and let the water flow out
of the hose.
4. Empty the drain pump. Refer to the
emergency drain procedure.
5. When the drain pump is empty,
install the inlet hose again.
WARNING!
Make sure that the
temperature is higher than 0
°C before you use the
appliance again.
The manufacturer is not
responsible for damages
caused by low temperatures.
Page 31
13. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
13.1 Introduction
The appliance does not start or it stops
during operation.
First try to find a solution to the problem
(refer to the table). If the problem
persists, contact the Authorised Service
Centre.
In case of major problems, the acoustic
signals operate, the display shows an
alarm code and the 启动/暂停 button
may flash continuously:
- The appliance does not fill with
•
water properly.
Start the appliance again by pressing
启动/暂停 button. After 5 seconds the
door will be unlocked.
•
•
- The appliance does not drain
the water.
- The appliance door is open or
not closed correctly. Please check the
door!
If the appliance is
overloaded, remove
some items from the
drum and/or keep
pressed the door while
touching the 启动/暂停
button until the indicator
stops flashing (see
the picture below).
ENGLISH 31
• - The mains supply is unstable.
Wait until the mains supply is stable.
•
- No communication between
electronic elements of the appliance.
Switch it off and switch on again.
The programme was not finished
properly or the appliance stopped
too early. If the alarm code appears
again, contact the Authorised Service
Centre.
•
- The anti-flood device is on.
Disconnect the appliance and close
the water tap. Contact the Authorised
Service Centre.
WARNING!
Deactivate the appliance
before carrying out any
check.
13.2 Possible failures
Problem Possible solution
• Make sure that the mains plug is connected to the mains
socket.
• Make sure that the appliance door is closed.
The programme does
not start.
• Make sure that there is no damaged fuse in the fuse box.
• Make sure that the 启动/暂停 has been touched.
• If the delay start is set, cancel the setting or wait for the end
of countdown.
• Deactivate the Child Lock function if it is on.
Page 32
www.aeg.com32
Problem Possible solution
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too
low. For this information, contact your local water authority.
• Make sure that the water tap is not clogged.
The appliance does not
fill with water properly.
• Make sure that the inlet hose has no kinks, damages or
bends.
• Make sure that the connection of the water inlet hose is
correct.
• Make sure that the filter of the inlet hose and the filter of
the valve are not clogged. Refer to 'Care and cleaning'.
The appliance fills with
water and drains immediately
• Make sure that the drain hose is in the correct position. The
hose may be positioned too low. Refer to "Installation instruction".
• Make sure that the sink spigot is not clogged.
•
Make sure that the drain hose has no kinks or bends.
• Make sure that the drain filter is not clogged. Clean the fil-
The appliance does not
drain the water.
ter, if necessary. Refer to "Care and cleaning".
• Make sure that the connection of the drain hose is correct.
• Set the drain programme if you set a programme without
drain phase.
• Set the drain programme if you set an option which ends
with water in the tub.
• Set the spin programme.
The spin phase does not
operate or the washing
cycle lasts longer than
usual.
• Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
• Adjust manually the items in the tub and start the spin
phase again. This problem may be caused by balance problems.
• Make sure that the couplings of the water hoses are tight
and there is not water leakages.
There is water on the
floor.
• Make sure that the water inlet hose and the drain hose have
no damages.
• Make sure you use the correct detergent and the correct
quantity of it.
• Make sure that a washing programme that ends with water
in tub, has been selected.
• Make sure that the washing programme is finished.
• Set the drain or the spin programme if there is water in the
You cannot open the appliance door.
drum.
• Make sure that the appliance receives electrical power.
• This problem may be caused by a failure of the appliance.
Contact the Authorised Service Centre.
If you need to open the door, please read carefully "Emergency door opening".
Page 33
Problem Possible solution
• Make sure the levelling of the appliance is correct. Refer to
The appliance makes an
unusual noise and vibrates.
The programme duration
increases or decreases
during programme execution.
The washing results are
not satisfactory.
Too much foam in the
drum during the washing
cycle.
After the washing cycle,
there are some detergent residues in the dispenser drawer.
"Installation instruction".
• Make sure that the packaging and/or the transit bolts are
removed. Refer to "Installation instruction".
• Add more laundry in the drum. The load may be too small.
• The ProSense function is able to adjust the programme du-
ration according to the type and the laundry load size. Refer to "The ProSense load detection" in "Daily Use" chapter.
• Increase the detergent quantity or use a different deter-
gent.
•
Use special products to remove the stubborn stains before
you wash the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
• Reduce the quantity of detergent.
• Make sure that the flap is in the correct position (UP for
powder detergent - DOWN for liquid detergent).
• Make sure you have used the detergent dispenser accord-
ing the indications given in this user manual.
ENGLISH 33
After the check, activate the appliance. The programme continues from the point of
interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes. Deactivate and activate the appliance. If the
problem continues, contact the Authorised Service Centre.
13.3 Emergency door opening
In case of power failure or functioning
failure the appliance door remains
locked. The washing programme
continues when the power is restored. If
the door remains locked in case of
failure, it is possible to open it using the
emergency unlock function.
Before opening the door:
CAUTION!
Risk of burns! Make sure
that the water
temperature is not too
high and the laundry is not
hot. If necessary, wait until
they cool down.
To open the door, proceed as follows:
CAUTION!
Risk of injury! Make sure
that the drum is not
rotating. If necessary, wait
until the drum stops
rotating.
Make sure that the water
level inside the drum is not
too high. If necessary,
proceed with an
emergency drain (refer to
«Emergency drain» in
«Care and cleaning»
chapter).
Page 34
www.aeg.com34
1. Press the 开/关 button to switch
the appliance off.
2. Disconnect the mains plug from the
mains socket.
3. Open the filter flap.
4. Pull twice the emergency unlock
trigger downward and open the
appliance door.
14. TECHNICAL DATA
Dimension Width/ Height/ Depth/
Total depth
Electrical connection Voltage
Overall power
Fuse
Frequency
Level of protection against ingress of solid particles
and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture
Water supply pressure Minimum
Maximum
Water supply
Maximum Load Cotton 10 kg
Energy Efficiency Class Level 1
Spin Speed Maximum 1400 rpm
This product meets the following standards:
Energy efficiency standard number: GB12021.4, Energy efficiency rating is 1;
CCC standard number: GB17625.1; GB4343.1; GB4706.1; GB4706.24;
Manufacturer: Guangdong Deyijie Electric Appliance Co., Ltd.
1)
Connect the water inlet hose to a water tap with a 3/4'' thread.
1)
5. Take out the laundry and then close
the appliance door.
6. Close the filter flap.
600 mm/ 850 mm/ 630 mm/ 660 mm
220 - 240 V
2200 W
10 A
50 Hz
IPX4
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Cold water
Page 35
15. ACCESSORIES
ENGLISH 35
15.1 Available in www.aeg.com/shop or from authorised dealer
Only appropriate
accessories approved by
AEG ensure the safety
standards of the appliance. If
unapproved parts are used,
any claims will be
invalidated.
15.2 Fixing plate kit
If you install the appliance on a plinth,
secure the appliance with the fixing
plates.
Read carefully the instructions supplied
with the accessory.
15.3 Stacking kit
Verify the compatible
stacking kit by checking the
depth of your appliances.
The stacking kit can be used only with
the appliances specified in the leaflet
provided with the accessory.
Read carefully the instructions supplied
with the appliance and with the
accessory.
WARNING!
Do not put the tumble dryer
under the washing machine.
15.4 Pedestal with the drawer
To raise your appliance and make
loading and unloading laundry easier.
The drawer can be used for laundry
storage e.g.: towels, cleaning products
and more.
The tumble dryer can be stacked on the
top of the washing machine only by
using the correct stacking kit
manufactured and approved by AEG.
Read carefully the instructions supplied
with the accessory.
16. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
Page 36
EN
Hazardous substances
Parts Name
Pb Hg Cd Cr6+ PBBs PBDEs
Cabinet (including fl oater and back panel)
Washing group (including drum, tub, heater,
pulley)
X
Motor (including belt)
X
Hydraulics (inlet and drain hoses, pressure switch,
pumps, including electrovalves)
X
Control panel (including sensors, electronic
boards - user interface, main board, motor control
bard)
X
Door (including hinge)
X
Wirings and power cord
X
Worktop
Note:
1. This table is compiled according to SJ/T11364-2014.
2.
means this kind of hazard substance content in all the homogenous material of this part is under the limitation regulated
in GB/T26572-2011.
3.
X
means this kind of hazard substance content in at least one homogenous material of this part is above the limitation regulated
in GB/T26572-2011.
4. For these parts with
X
in the above table, there is no replacement solution due to technique limitation in the industry;
however, this may change with the technique improvement.
5. Under normal usage condition, the environment friendly usage period is 15 year.
www.aeg.com36
*
Page 37
ENGLISH 37
Page 38
www.aeg.com38
Page 39
ENGLISH 39
Page 40
www.aeg.com/shop
157024500-A-442018
Loading...